Improved Smith prediction monitoring AGC system based on feedback-assisted iterative learning control

The performance of Smith prediction monitoring automatic gauge control(AGC) system is influenced by model mismatching greatly in strip rolling process. Aiming at this problem, a feedback-assisted iterative learning control strategy, which learned unknown modeling error by using previous control information repeatedly, was introduced into Smith prediction monitoring AGC system. Firstly, conventional Smith predictor and improved Smith predictor with PI-P controller were analyzed. Secondly, on the basis of establishing of feedback-assisted iterative learning control strategy for improved Smith predictor, process control signal update law and control error were deduced, then convergence condition of this strategy was put forward and proved. Finally, after modeling the automatic position control system, the PI-P Smith prediction monitoring AGC system with feedback-assisted iterative learning control was researched through simulation. Simulation results indicate that this system remains stable during model mismatching. The robustness and response of monitoring AGC is improved by development of feedback-assisted iterative learning control strategy for PI-P Smith predictor.

Design and implementation of digital closed-loop drive control system of a MEMS gyroscope

In order to effectively control the working state of the gyroscope in drive mode, the drive characteristics of the micro electromechanical system （MEMS） gyroscope are analyzed in principle. A novel drive circuit for the MEMS gyroscope in digital closed-loop control is proposed, which utilizes a digital phase-locked loop （PLL） in frequency control and an automatic gain control （AGC） method in amplitude control. A digital processing circuit with a field programmable gate array （FPGA） is designed and the experiments are carried out. The results indicate that when the temperature changes, the drive frequency can automatically track the resonant frequency of gyroscope in drive mode and that of the oscillating amplitude holds at a set value. And at room temperature, the relative deviation of the drive frequency is 0.624 ×10^-6 and the oscillating amplitude is 8.0 ×10^-6, which are 0. 094% and 18. 39% of the analog control program, respectively. Therefore, the control solution of the digital PLL in frequency and the AGC in amplitude is feasible.

Design of a Proportional-Integral-Derivative Controller for an Automatic Generation Control of Multi-area Power Thermal Systems Using Firefly Algorithm

Essentially, it is significant to supply the consumer with reliable and sufficient power. Since, power quality is measured by the consistency in frequency and power flow between control areas. Thus, in a power system operation and control,automatic generation control(AGC) plays a crucial role. In this paper, multi-area(Five areas: area 1, area 2, area 3, area 4 and area 5) reheat thermal power systems are considered with proportional-integral-derivative(PID) controller as a supplementary controller. Each area in the investigated power system is equipped with appropriate governor unit, turbine with reheater unit, generator and speed regulator unit. The PID controller parameters are optimized by considering nature bio-inspired firefly algorithm(FFA). The experimental results demonstrated the comparison of the proposed system performance(FFA-PID)with optimized PID controller based genetic algorithm(GAPID) and particle swarm optimization(PSO) technique(PSOPID) for the same investigated power system. The results proved the efficiency of employing the integral time absolute error(ITAE) cost function with one percent step load perturbation(1 % SLP) in area 1. The proposed system based FFA achieved the least settling time compared to using the GA or the PSO algorithms, while, it attained good results with respect to the peak overshoot/undershoot. In addition, the FFA performance is improved with the increased number of iterations which outperformed the other optimization algorithms based controller.

Switched-mode AGC circuits with internally created reset module for burst-mode unbalanced data optical receiver

This paper presents an innovative switched-mode auto gain control （AGC） circuit with internally created reset module for DC-10Mb/s burst-mode unbalanced （BMU） optical data transmission. Conventional AGC circuit is inappropriate for BMU data transmission because it is based on average level detection and requires considerable time to settle on a predefined gain. Therefore, we adopt a fast switched-mode AGC based on peak level detection. After the gain is adjusted, the peak level detectors need to re-detect the peak level of the input signal. Thus, we develop an internally created reset module. This AGC with reset module exhibits a fast operation and achieves an adjusted stable gain within one-bit, avoiding any bit loss up to 10Mb/s data rate. During power-up, the peak level detectors possibly hold an uncertain level resulting in the bit-errors. We propose a power-up reset circuit to solve this problem. Designed in a 0.5μm CMOS technology, the circuit achieves an optical sensitivity of better than -30dBm and a wide dynamic range of over 30dB with a power dissipation of only 30 mW from a 5V supply.

Research on Wind Farm Participation in Power Grid AGC Control

Since wind power has the features of being intermittent and unpredictable, and usually needs transmission over long distances, grid integration of large-scale wind power will exert signif icant influence on power grid planning and construction, and will make a heavy impact on the safe and reliable operation of power systems. To deal with the diff iculties of large scale wind power dispatch, this paper presents a new automatic generation control (AGC) scheme that involves the participation of wind farms. The scheme is based on ultra-short-term wind power forecast. The author establishes a generation output distribution optimization mode for the power system with wind farms and verif ies the feasibility of the scheme by an example.

The Techniques to Reduce Variations within One Plate

Conventional techniques to control variations within one plate have been based on preset models and constant automatic position control (APC or pressure feedback automatic gauge control(PAGC).However.because of the rolling force prediction error in the preset models and of the inadequate response speed of dynamic system and of the eccentricity, etc.,the conventional method has not given satisfactory results, the statistics'variations within one plate are in range of 0.25-0.60 mm The authors have developed the techniques to control the variations, which are dynamic intelligent control of hydraulic screwdown system. synchronism control of hydraulic screwdown, eccentricity control method by rotary encoder and the curve of modulus of mill measured automatically, etc., The techniques were fully and successfully industrialized in The Plate Mill of Maanshan Iron and Steel Company and good results that variations are in range of 0.08-0.15min hare been obtained in that mill.

A Novel Cascaded PID Controller for Automatic Generation Control Analysis With Renewable Sources

Present day power scenarios demand a high quality uninterrupted power supply and needs environmental issues to be addressed. Both concerns can be dealt with by the introduction of the renewable sources to the existing power system. Thus, automatic generation control(AGC) with diverse renewable sources and a modified-cascaded controller are presented in the paper.Also, a new hybrid scheme of the improved teaching learning based optimization-differential evolution(hITLBO-DE) algorithm is applied for providing optimization of controller parameters. A study of the system with a technique such as TLBO applied to a proportional integral derivative(PID), integral double derivative(IDD) and PIDD is compared to hITLBO-DE tuned cascaded controller with dynamic load change.The suggested methodology has been extensively applied to a 2-area system with a diverse source power system with various operation time non-linearities such as dead-band of, generation rate constraint and reheat thermal units. The multi-area system with reheat thermal plants, hydel plants and a unit of a wind-diesel combination is tested with the cascaded controller scheme with a different controller setting for each area. The variation of the load is taken within 1% to 5% of the connected load and robustness analysis is shown by modifying essential factors simultaneously by± 30%. Finally, the proposed scheme of controller and optimization technique is also tested with a 5-equal area thermal system with non-linearities. The simulation results demonstrate the superiority of the proposed controller and algorithm under a dynamically changing load.

Response characteristics of sonar receiver under intense sound pulse

For anti-jamming and anti-countermeasure techniques of the sonar receiver, the response characteristics of the automatic gain control （AGC） circuit and the survivability of the prime circuit under strong interference are analyzed by simulations and experiments. An AGC simulation model based on the voltage control amplifier VCA810 prototype is proposed. Then static and dynamic simulations are realized with single frequency signal and linear frequency modulated （LFM） signal commonly used in the active sonar. Based on intense sound pulse （ISP） interference experiments, the real-time response characteristics of each module of the receiver are studied to verify the correctness of the model as well as the simulation results. Simulation and experiment results show that, under 252 dB/20 μs ISP interference, the specific sonar receiver will produce sustained cut top oscillation above 30 ms, which may affect the receiver and block the regular sonar signal.

Design of a 6.25 Gbps backplane SerDes with adaptive decision feedback equalization

A 6.25 Gbps SerDes core used in the high signed based on the OIF-CEI-02.0 standard. To speed backplane communication receiver has been decounteract the serious Inter-Syrmbol-Interference （ISI）, the core employed a half-rate four-tap decision feedback equalizer （DFE）. The equalizer used the Signsign least mean-squared （SS-LMS） algorithm to realize the coefficient adaptation. An automatic gain control （AGC） amplifier with the sign least mean-squared （S-LMS） algorithm has been used to compensate the transmission media loss. To recover the clock signal from the input data serial and provide for the DFE and AGC, a bang-bang clock recovery （BB-CR） is adopted. A third order phase loop loek （PLL） model was proposed to predict characteristics of the BB-CR. The core has been verified by behavioral modeling in MATLAB. The results indicate that the core can meet the specifications of the backplane receiver. The DFE recovered data over a 34＂ FR-4 backplane has a peak-to-peak jitter of 17 ps, a horizontal eye opening of 0.87 UI, and a vertical eye opening of 500 mVpp.

CMOS Automatic Gain Control Circuit with DC Offset Cancellation for FM/cw Ladar

This paper presented an automatic gain control （AGC） circuit suitable for FM/cw ladar. The proposed architecture was based on two-stage variable gain amplifier （VGA） chain with a novel DC offset canceller circuit, which contained an improved Gilbert cell and a Gm-C feedback loop. To keep the VGA with a linearity in dB characteristic, an improved exponential gain control circuit was introduced. The AGC was implemented in 0.18 gm standard CMOS process. Simulation and measurement results verified that its gain ranged from -20 dB to 30 dB, and band- width ranged from 100 kHz to 10 MHz. Its power consumption was 19.8 mW under a voltage supply of 3.3 V.

Anti-interference Strategy of 20-Hi Cold Mill Automatic Gauge Control

Automatic gauge control(AGC in the article)is the key technology of product thickness accuracy and flatness quality in modern cold rolling mill.Most traditional AGC control algorithms need stable external system conditions and hard to stabilize under complex interference that meets coverage requirements.This paper presents a new anti-interference strategy for AGC control of 20-Hi cold reversing mill.The proposed algorithm introduces a united dynamic weights algorithm of feed forward-mass flow to avoid the complex interference problem in AGC control,the relevant control strategy is provided to eliminate the adverse effects.At the same time,the D-value between feed forward-mass flow pre-computation and thickness measurement deviation is dynamic compared,the final gap position regulation is calculated by developing a set of united dynamic weights between feed forward control and mass flow control.Finally,the output of controllers is sent to actuator though a constant rate smoothing.The proposed strategy is compared with conventional AGC control on Experimental platform and project application,the results show that the proposed strategy is more stable than comparison method and majority of system uncertainty produced by mentioned interference is significantly eliminated.

Acquisition algorithm assisted by AGC control voltage for DSSS signals

An appropriate acquisition configuration in terms of signal quality can optimize the acquisition performance. In view of this, a new approach of acquisition assisted by the control voltage of automatic gain control(AGC) is proposed. This approach judges the signal power according to the AGC control voltage and switches the working modes correspondingly and adaptively. Non-coherent accumulation times and the detection threshold are reconfigured according to the working mode. Theoretical derivation and verification by simulation in typical situations are provided, and the algorithm is shown to be superior in terms of the mean acquisition time, especially in strong signal scenarios compared with the conventional algorithm.

State-of-the-art review on frequency response of wind power plants in power systems

With an increasing penetration of wind power in the modern electrical grid, the increasing replacement of large conventional synchronous generators by wind power plants will potentially result in deteriorated frequency regulation performance due to the reduced system inertia and primary frequency response. A series of challenging issues arise from the aspects of power system planning,operation, control and protection. Therefore, it is valuable to develop variable speed wind turbines(VSWTs) equipped with frequency regulation capabilities that allow them to effectively participate in addressing severe frequency contingencies. This paper provides a comprehensive surveyon frequency regulation methods for VSWTs. It fully describes the concepts, principles and control strategies of prevailing frequency controls of VSWTs, including future development trends. It concludes with a performance comparison of frequency regulation by the four main types of wind power plants.

Real-time AGC dispatch units considering wind power and ramping capacity of thermal units

The high penetration of wind energy sources in power systems has substantially increased the demand for faster-ramping thermal units participating in the frequency regulation service.To fulfill the automatic generation control(AGC)and compensate the influence of wind power fluctuations simultaneously,ramping capacity should be considered in the dispatch model of thermals.Meanwhile,conventional methods in this area do not take the impact of transmission loss into the dispatch model,or rely on offline network model and parameters,failing to reflect the real relationships between the wind farms and thermal generators.This paper proposes an online approach for AGC dispatch units considering the above issues.Firstly,the power loss sensitivity is online identified using recursive least square method based on the real-time data of phasor measurement units.It sets up power balance constraint and results in a more accurate dispatch model.Then,an improved multi-objective optimization model of dispatch is proposed and a connection is established between the thermal units with fast ramping capacity and the wind farms with rapid fluctuations.Genetic algorithm is used to solve the dispatch model.The proposed method is compared with conventional methods in simulation case in the IEEE 30-bus system.Finally,simulation results verify the validity and the feasibility of identification method and optimization model.

A Two-stage Kalman Filter for Cyber-attack Detection in Automatic Generation Control System

Communication plays a vital role in incorporating smartness into the interconnected power system.However,historical records prove that the data transfer has always been vulnerable to cyber-attacks.Unless these cyber-attacks are identified and cordoned off,they may lead to black-out and result in national security issues.This paper proposes an optimal two-stage Kalman filter(OTS-KF)for simultaneous state and cyber-attack estimation in automatic generation control(AGC)system.Biases/cyber-attacks are modeled as unknown inputs in the AGC dynamics.Five types of cyber-attacks,i.e.,false data injection(FDI),data replay attack,denial of service(DoS),scaling,and ramp attacks,are injected into the measurements and estimated using OTS-KF.As the load variations of each area are seldom available,OTS-KF is reformulated to estimate the states and outliers along with the load variations of the system.The proposed technique is validated on the benchmark two-area,three-area,and five-area power system models.The simulation results under various test conditions demonstrate the efficacy of the proposed filter.

Real-time impact of power balancing on power system operation with large scale integration of wind power

Highly wind power integrated power system requires continuous active power regulation to tackle the power imbalances resulting from the wind power forecast errors. The active power balance is maintained in real-time with the automatic generation control and also from the control room, where regulating power bids are activated manually. In this article, an algorithm is developed to simulate the activation of regulating power bids, as performed in the control room, during power imbalance between generation and load demand. In addition, the active power balance is also controlled through automatic generation control, where coordinated control strategy between combined heat and power plants and wind power plant enhances the secure power system operation. The developed algorithm emulating the control room response,to deal with real-time power imbalance, is applied and investigated on the future Danish power system model. The power system model takes the hour-ahead regulating power plan from power balancing model and the generation and power exchange capacities for the year 2020 into account.The real-time impact of power balancing in a highly wind power integrated power system is assessed and discussed by means of simulations for different possible scenarios.

Application of Fractional Order PID Controller for AGC Under Deregulated Environment

In this paper, a fractional order proportional integral derivative （FOPID） controller for multiarea automatic generation control （AGC） scheme has been designed. FOPID controller has five parameters and provides two additional degrees of flexibility in comparison to a proportional integral derivative （PID） controller. The optimal values of parameters of FOPID controller have been determined using Big Bang Big Crunch （BBBC） search algorithm. The designed controller regulates real power output of generators to achieve the best dynamic response of frequency and tie-line power on a load perturbation. The complete scheme for designing of the controllers has been developed and demonstrated on multiarea deregulated power system. The performance of the designed FOPID controllers has been compared with the optimally tuned PID controllers. It is observed from the results that the FOPID controller shows a considerable improvement in the performance as compared to the conventional PID controller.

Dynamic stability enhancement of interconnected multi-source power systems using hierarchical ANFIS controller-TCSC based on multi-objective PSO

Suppression of the dynamic oscillations of tie-line power exchanges and frequency in the affected interconnected power systems due to loading-condition changes has been assigned as a prominent duty of automatic generation control(AGC). To alleviate the system oscillation resulting from such load changes, implementation of flexible AC transmission systems(FACTSs) can be considered as one of the practical and effective solutions. In this paper, a thyristor-controlled series compensator(TCSC), which is one series type of the FACTS family, is used to augment the overall dynamic performance of a multi-area multi-source interconnected power system. To this end, we have used a hierarchical adaptive neuro-fuzzy inference system controller-TCSC(HANFISC-TCSC) to abate the two important issues in multi-area interconnected power systems, i.e., low-frequency oscillations and tie-line power exchange deviations. For this purpose, a multi-objective optimization technique is inevitable. Multi-objective particle swarm optimization(MOPSO) has been chosen for this optimization problem, owing to its high performance in untangling non-linear objectives. The efficiency of the suggested HANFISC-TCSC has been precisely evaluated and compared with that of the conventional MOPSO-TCSC in two different multi-area interconnected power systems, i.e., two-area hydro-thermal-diesel and three-area hydro-thermal power systems. The simulation results obtained from both power systems have transparently certified the high performance of HANFISC-TCSC compared to the conventional MOPSO-TCSC.

Real-time vehicle-to-grid control for frequency regulation with high frequency regulating signal

The large-scale popularization of electric vehicles(EVs)brings the potential for grid frequency regulation.Considering the characteristics of fast response and adjustment of EVs,two control strategies of automatic generation control(AGC)with EVs are proposed responding to two high frequency regulating signals extracted from area control error(ACE)and area regulation requirement(ARR)by a digital filter,respectively.In order to dispatch regulation task to EVs,the capacity of regulation is calculated based on maximum V2G power and the present V2G power of EVs.Finally,simulations based on a two-area interconnected power system show that the proposed approaches can significantly suppress frequency deviation and reduce the active power output of traditional generation units.

Automatic Generation Control with Virtual Synchronous Renewables

As synchronous generators(SGs)are gradually displaced by renewable energy sources(RESs),the frequency stability of power systems deteriorates because RESs,represented by utility-scale solar and wind power sources,do not provide the inertial response,primary frequency response,secondary frequency response,and tertiary frequency regulation.As a result,the remaining SGs may not be sufficient to maintain the power balance and frequency stability.The concept and control strategies of virtual synchronous generators(VSGs)enable the inverter-based wind and solar power sources to emulate the outer characteristics of traditional SGs and participate in the active power and frequency control of power systems.This paper focuses on the automatic generation control(AGC)with virtual synchronous renewables(VSRs).First,the VSR strategy that enables the RESs to participate in AGC is introduced.Second,based on the interval representation of uncertainty,the output of RES is transformed into two portions,i.e.,the dispatchable portion and the stochastic portion.In the dispatchable portion,the RESs can participate in AGC jointly with SGs.Accordingly,a security-constrained economic dispatch(SCED)model is built considering the RESs operating in VSR mode.Third,the solution strategy that employs the slack variables to acquire deterministic constraints is introduced.Finally,the proposed SCED model is solved based on the 6-bus and 39-bus systems.The results show that,compared with the maximum power point tracking(MPPT)mode,VSRs can participate in the active power and frequency control jointly with SGs,increase the maximum penetration level of RESs,and decrease the operating cost.