The effects of three different aging treatment processes,namely single-stage,double-stage,and reverse double-stage aging treatment processes,on the microstructures and mechanical properties of the AZ63(Mg-6Al-3Zn-0.25...The effects of three different aging treatment processes,namely single-stage,double-stage,and reverse double-stage aging treatment processes,on the microstructures and mechanical properties of the AZ63(Mg-6Al-3Zn-0.25Mn)casting magnesium alloy were investigated and compared.The results indicate that the microstructures of all the aged alloys under the three treatment processes are mainly composed ofα-Mg,Mg17Al12),and Al4Mn phases,indicating that the double-stage and reverse double-stage aging treatments have no obvious effect on the type of alloy phases.However,as compared with the single-stage and double-stage processes,the reverse double-stage process has a great effect on the quantity of the Mg17Al12phases.After the reverse double-stage aging treatment,which results in a stronger drive for decomposition of the supersaturated solid solution,the number of Mg17Al12phases precipitated in the grains significantly increases.In addition,as compared with the single-stage aged alloy,the tensile properties at room temperature for both the double-stage and reverse double-stage aged alloys are significantly improved.Among them,the reverse double-stage aged alloy achieves the highest tensile strength,yield strength,and elongation of 295 MPa,167 MPa,and 8.6%,respectively.展开更多
In this study, grain refining effect of Al-1.5℃ master alloy was examined on an AZ63B magnesium alloy, and the refining mechanism was studied through investigating the role of C and Fe in this process. The results sh...In this study, grain refining effect of Al-1.5℃ master alloy was examined on an AZ63B magnesium alloy, and the refining mechanism was studied through investigating the role of C and Fe in this process. The results show that addition of Al-1.5℃ master alloy leads to significant decrease of the mean grain size from about 270μm to 50μm at the center of the AZ63 alloy ingot. Grain refinement by carbon addition is mainly due to the heterogeneity nucleation on the Al-, C-, O-, Fe- and Mn-rich particles, but not constitutional undercooling caused by the carbon solute element. Fe plays an important role in the formation of the nucleating particles, but not acts as an inhibiting element.展开更多
Effects of Ca addition on the microstructure and viscosity as well as electrochemical properties of casting AZ63 magnesium alloy were studied. Testing results show that the viscosity value increases with the increase ...Effects of Ca addition on the microstructure and viscosity as well as electrochemical properties of casting AZ63 magnesium alloy were studied. Testing results show that the viscosity value increases with the increase of calcium content, especially at the higher temperature, and there exists such a relation between the ignition temperature and viscosity of magnesium alloy: when the melt viscosity increases, the ignition temperature increases too. The microstructure of AZ63 magnesium alloy is first refined and then coarsened with the increase of Ca addition. By the addition of 0.15% Ca, AZ63 alloy has more negative open-circuit potential(1.624 5V), bigger anode efficiency (55.65%) and lower corrosion rate(0.214 g/(m^2·h)). AZ63 alloy containing some Ca content is a high driving-potential and high-efficiency sacrificial anodes material.展开更多
Due to their high specific strength and low density, magnesium alloys are widely used in many weight-saving applications. This research is aimed at investigating the microstructure and hardness of commercial AZ63 allo...Due to their high specific strength and low density, magnesium alloys are widely used in many weight-saving applications. This research is aimed at investigating the microstructure and hardness of commercial AZ63 alloy specimens subjected to two different thermomechanical treatments （TMTs）. For the first TMT, after solution treated at the temperature of 380 ℃ for 20 h, AZ63 alloy specimens were 5% cold worked by rolling process followed by ageing at the temperatures of 150 ℃and 250 ℃ for 3, 9 and 25 h. In the second TMT, the specimens were solution treated at the temperature of 380 ℃ for 20 h, underwent 2% cold worked and quenched in water of 0 ℃. Half of the specimens were then 2% cold worked whilst the rest were rolled to 8% cold worked. All the specimens were then aged at the temperatures of 150 ℃ and 250 ℃ for 3, 9 and 25 h. Optical microscope was used to analyze the microstructures of the specimens. Hardness test was too conducted to measure the effect of the treatments on the specimens. Results show that two-step aging enhances the hardness of the specimens due to the distribution of fine β-phase （MglTA112） in the alloy matrix. The results also reveal that, the best hardness from the first TMT was produced by specimen that was pre-aged at 150 ℃ whereas, in the second TMT, aging at 250 ℃ exhibited the best hardness values.展开更多
基金supported by the National Key R&D Program of China(Grant No.2018YFB1106800)the National Natural Science Foundation of China(Grant No.51771152)。
文摘The effects of three different aging treatment processes,namely single-stage,double-stage,and reverse double-stage aging treatment processes,on the microstructures and mechanical properties of the AZ63(Mg-6Al-3Zn-0.25Mn)casting magnesium alloy were investigated and compared.The results indicate that the microstructures of all the aged alloys under the three treatment processes are mainly composed ofα-Mg,Mg17Al12),and Al4Mn phases,indicating that the double-stage and reverse double-stage aging treatments have no obvious effect on the type of alloy phases.However,as compared with the single-stage and double-stage processes,the reverse double-stage process has a great effect on the quantity of the Mg17Al12phases.After the reverse double-stage aging treatment,which results in a stronger drive for decomposition of the supersaturated solid solution,the number of Mg17Al12phases precipitated in the grains significantly increases.In addition,as compared with the single-stage aged alloy,the tensile properties at room temperature for both the double-stage and reverse double-stage aged alloys are significantly improved.Among them,the reverse double-stage aged alloy achieves the highest tensile strength,yield strength,and elongation of 295 MPa,167 MPa,and 8.6%,respectively.
基金supported by the National Natural Science Foundation of China(No.50171037)Natural Science Foundation of Shandong Province of China(No.Z2004F03).
文摘In this study, grain refining effect of Al-1.5℃ master alloy was examined on an AZ63B magnesium alloy, and the refining mechanism was studied through investigating the role of C and Fe in this process. The results show that addition of Al-1.5℃ master alloy leads to significant decrease of the mean grain size from about 270μm to 50μm at the center of the AZ63 alloy ingot. Grain refinement by carbon addition is mainly due to the heterogeneity nucleation on the Al-, C-, O-, Fe- and Mn-rich particles, but not constitutional undercooling caused by the carbon solute element. Fe plays an important role in the formation of the nucleating particles, but not acts as an inhibiting element.
文摘Effects of Ca addition on the microstructure and viscosity as well as electrochemical properties of casting AZ63 magnesium alloy were studied. Testing results show that the viscosity value increases with the increase of calcium content, especially at the higher temperature, and there exists such a relation between the ignition temperature and viscosity of magnesium alloy: when the melt viscosity increases, the ignition temperature increases too. The microstructure of AZ63 magnesium alloy is first refined and then coarsened with the increase of Ca addition. By the addition of 0.15% Ca, AZ63 alloy has more negative open-circuit potential(1.624 5V), bigger anode efficiency (55.65%) and lower corrosion rate(0.214 g/(m^2·h)). AZ63 alloy containing some Ca content is a high driving-potential and high-efficiency sacrificial anodes material.
文摘Due to their high specific strength and low density, magnesium alloys are widely used in many weight-saving applications. This research is aimed at investigating the microstructure and hardness of commercial AZ63 alloy specimens subjected to two different thermomechanical treatments （TMTs）. For the first TMT, after solution treated at the temperature of 380 ℃ for 20 h, AZ63 alloy specimens were 5% cold worked by rolling process followed by ageing at the temperatures of 150 ℃and 250 ℃ for 3, 9 and 25 h. In the second TMT, the specimens were solution treated at the temperature of 380 ℃ for 20 h, underwent 2% cold worked and quenched in water of 0 ℃. Half of the specimens were then 2% cold worked whilst the rest were rolled to 8% cold worked. All the specimens were then aged at the temperatures of 150 ℃ and 250 ℃ for 3, 9 and 25 h. Optical microscope was used to analyze the microstructures of the specimens. Hardness test was too conducted to measure the effect of the treatments on the specimens. Results show that two-step aging enhances the hardness of the specimens due to the distribution of fine β-phase （MglTA112） in the alloy matrix. The results also reveal that, the best hardness from the first TMT was produced by specimen that was pre-aged at 150 ℃ whereas, in the second TMT, aging at 250 ℃ exhibited the best hardness values.
