Properties of Activated Carbons from Sugarcane Leaves and Rice Straw Derived Charcoals by Activation at Low Temperature via KMnO_(4)Pre-Oxidation-Hydrolysis

Activated carbon preparation from sugarcane leaves and rice straw by carbonization(250℃–400℃)and activation at 500℃were studied.The effects of pre-oxidation,hydrolysis of derived charcoals by boiled KMnO4 aqueous solution were evaluated.The derived charcoals products were pretreated using oxidation-hydrolysis with 1–5 wt.%KMnO4 at 100℃and then activated at 500℃.The derived charcoal and activated carbon products were characterized by FTIR,XRD,SEM-EDS and BET.Iodine number and methylene blue number of derived products were also used for the analysis of the products.It was found that fabricated charcoal materials made at 350℃–400℃possess good characteristics with low content of surface functional groups and high carbon content.After pre-oxidation-hydrolysis and activation at 500℃,the resulting derived activated carbon materials from charcoals with 400℃carbonization temperature have high content of oxygen containing surface functional groups such as Mn-O,Si-O,Si-O-Si,C-O,or O-H.In addition,MnO_(2) accumulated on the surface of the derived activated carbon products.The surface area and pore volume of the activated carbon products have also increased with increasing of KMnO_(4) concentration from 1 to 3 wt.%and then decreased with 5 wt.%used during activation.Therefore,activated carbon products made by pre-oxidation-hydrolysis with 3 wt.%KMnO_(4) were used for Fe(Ⅲ)adsorption experiments.It was found that Fe(Ⅲ)adsorption on the activated carbon materials can be fitted with both the Freundlich and the Langmuir models.The calculated maximum Fe(Ⅲ)adsorption capacities of sugarcane leaves derived activated carbon and rice straw derived activated carbon products were 50.00 and 39.37 mg/g,respectively.It was shown that the effect of pre-oxidation-hydrolysis by KMnO_(4) and activation at 500℃are beneficial for activated carbon preparation with environmentally friendly and low-cost simplified operation.

Preparation and Characterization of Activated Carbons from Palm Nut Shells: Effects of Calcination Temperature on Porosity and Chemical Properties

Activated carbons (ACs) calcined at 400˚C, 500˚C, and 600˚C (AC-400, AC-500, and AC-600) were prepared using palm nut shells from Gabon as raw material and zinc chloride (ZnCl2) as a chemical activating agent. Prepared ACs were characterized by physisorption of nitrogen (N2), determination of diode and methylene blue numbers for studies of porosity and by quantification and determination of surface functional groups and pH at point of zero charge (pHpzc) respectively, for studies of chemical properties of prepared ACs. Then, effects of calcination temperature (Tcal) on porosity and chemical properties of prepared ACs were studied. The results obtained showed that when the calcination temperature increases from 500˚C to 600˚C, the porosity and chemical properties of prepared ACs are modified. Indeed, the methylene blue and iodine numbers determined for activated carbons AC-400 (460 and 7.94 mg·g−1, respectively) and AC-500 (680 and 8.90 mg·g−1, respectively) are higher than those obtained for AC-600 (360 and 5.75 mg·g−1, respectively). Compared to the AC-500 adsorbent, specific surface areas (SBET) and microporous volume losses for AC-600 were estimated to 44.7% and 45.8%, respectively. Moreover, in our experimental conditions, the effect of Tcal on the quantities of acidic and basic functional groups on the surface of the ACs appears negligible. In addition, results of the pHpzc of prepared ACs showed that as Tcal increases, the pH of the adsorbents increases and tends towards neutrality. Indeed, a stronger acidity was determined on AC-400 (pHpzc = 5.60) compared to those on AC-500 and AC-600 (pHpzc = 6.85 and 6.70, respectively). Also according to the results of porosity and chemical characterizations, adsorption being a surface phenomenon, 500˚C appears to be the optimal calcination temperature for the preparation of activated carbons from palm nut shells in our experimental conditions.

Elimination, Kinetics and Thermodynamics of Fe(II) Ions by Adsorption in Static and Dynamic Conditions on Activated Carbons in Aqueous Media

This work investigated the removal, kinetics and thermodynamics of iron(II) ions (Fe(II)) by adsorption in static and dynamic conditions in aqueous media on activated carbons (AC-i30min, AC-i1h, and AC-i24h), prepared from palm nut shells collected in the city of Franceville to Gabon, using potassium hydroxide (KOH) as the activating agent. Results on the elimination of Fe(II) in static and dynamic adsorption on prepared activated carbons (ACs) showed that the AC-i24h adsorbent has the best Fe(II) adsorption capacities at saturation (Qsat). The Qsat obtained on AC-i24h in static and dynamic conditions (17.87 and 10.38 mg/g, respectively) were higher than those of AC-i30min (13.89 and 5.54 mg/g respectively) and AC-i1h (14.92 and 8.64 mg/g respectively). Moreover, the static adsorption was more effective in the removal of Fe(II) ions in aqueous media in our experimental conditions. The percentage removal (%E) of Fe(II) obtained on prepared activated carbons in static conditions was better than those obtained in dynamic conditions, especially on AC-i24h, where the %E was 89.27% in static and 61.56% in dynamic. In kinetics, results showed that the pseudo-second-order kinetic model best described the adsorption mechanisms of Fe(II) on prepared activated carbons in static adsorption, with mainly of chemisorption on the solid surfaces. However, in dynamic conditions, the pseudo-first-order kinetic model was more suitable. In addition to the weak interactions between Fe(II) and the activated carbon surfaces, strong interactions (chemisorption) were also observed. Also, thermodynamic data obtained on AC-i24h in static adsorption indicated that the adsorption of Fe(II) was spontaneous and increased with temperature (ΔG˚ H˚ = 503.54 KJ/mol).

Adsorption Isotherm and Kinetics of Dibenzofuran on Granular Activated Carbons

The adsorption of dibenzofuran on three commercial granular activated carbons (ACs) was investigated by dynamic experiment to correlate the adsorption equilibrium and kinetics with the structure of activated carbons.Physical properties including surface area, average pore diameter, micropore area and micropore volume of the activated carbons were characterized by N2 adsorption experiment on ASAP2010. To calculate the adsorption parameters, adsorption isotherm data were fitted to the Langmuir equation, and adsorption kinetic data were fitted to the linear driving force (LDF) diffusion model. From the correlation results, it is concluded that the adsorption equilibrium and diffusion coefficient of dibenzofuran on activated carbon are controlled respectively by the total adsorbent surface area and the adsorbent pore diameter.

Synthesis of activated carbons from black sapote seeds,characterization and application in the elimination of heavy metals and textile dyes

Many different techniques may be used to remove industrial pollutants from wastewater. Adsorption using activated carbon has been reported to be an effective method. This work proposes the use of a vegetable residue(black sapote seeds) as a raw material for its synthesis. These carbons were chemically activated using phosphoric acid and carbonized at 673 and 873 K. Adsorption isotherms were constructed for the textile dyes on the carbons, and this data was treated using Langmuir’s equation to quantitatively describe the adsorption process. The synthesized carbons were characterized using FTIR, EA, SEM, Nitrogen adsorption(specific surface areas of 879 and 652 m2·g-1), and their points of zero charge(2.1 and 2.3). It was possible to adsorb both heavy metals and textile dyes present in aqueous solutions and wastewaters using these activated carbons. Heavy metals were adsorbed almost completely by both carbons. Cationic dyes where adsorbed(58–59.8 mg·g-1) in greater amounts compared to anionic dyes(10–58.8 mg·g-1). The amount of anionic dyes adsorbed increased almost 30% by changing the pH of the solutions. One of the carbons was thermally regenerated on three occasions without losing its adsorption capacity and it was proved in a flow system.

Optimization of Preparation Conditions of Activated Carbons Based on the Shells of Ricinodendron heudoltii

The purpose of this work is to prepare better activated carbons from the shells of Ricinodendron Heudelotii by chemical activation with sulfuric acid (H2SO4) and sodium hydroxide (NaOH). The process was optimized by a full factorial design (2K) based on the analysis of the external specific surface area of sixteen (16) activated carbons prepared according to the parameters of the preparation. This active analysis reveals that under the preparation conditions, good carbons are obtained for a sodium hydroxide concentration equal to 1 M, an impregnation time of 24 h and carbonization at 500˚C for 1 h. The external specific surface of this carbon is 358 m2 • g-1. The characteristics of this prepared carbon are as follows: a pH at zero point charge (pHpzc) of 8.2, a predominantly amorphous structure, a basic character and a low ash content (4.2%). It also has surface functions;the lactonic and carbonyl groups (C=O) at 1600 cm-1 and the carboxylate groups (O-H or C-O) at 1340 cm-1.

Preparation and Characterization of Activated Carbons from Asparagus Palm (Laccosperma robustum) Bark by Chemical Activation with H3PO4 and KOH

The present work deals with the preparation and characterization of activated carbons from the bark of the asparagus palm (Laccosperma robustum) by chemical activation with phosphoric acid and potassium hydroxide. The process was optimized on the basis of the analysis of the iodine number, methylene blue number and activated carbons yield as a function of the preparation parameters (concentration of the activating agents and the pyrolysis temperature). It emerges that the pyrolysis temperature and the concentration of activating agents influence the activated carbons preparation process. Their values were 500°C and 20% respectively for activated carbon with H3PO4 (ACP) and 700°C and 1.5% for activated carbon with KOH (ACK). The iodine numbers obtained were 850.26 mg/g for ACP and 865.49 mg/g for ACK. The methylene blue numbers obtained were 149.35 mg/g for ACP and 149.25 mg/g for ACK. The activated carbons yields obtained were 25% for ACP and 5.9% for ACK. The activated carbons prepared under optimal conditions have shown the pH of zero-point charge (pHzpc) of 4.4 and 7.0 for ACP for ACK respectively. The determination of the surface functions revealed that ACP had a strong acidic character while ACK had neutral character. The Fourier transformed infrared spectroscopy also showed the presence of different functional groups on the surface of the precursor and activated carbons.

Effect of Relative Humidity on Adsorption of Formaldehyde on Modified Activated Carbons

This work mainly involves the study of effect of relative humidity on adsorption of formaldehyde on the activated carbons modified with organosilane solution. Modification of activated carbons was carded out by impregnating activated carbon with organosilane/methanol-containing solutions. The breakthrough curves of formaldehyde in the packed beds of original and modified activated carbons were measured, respectively, at relative humidity of 30%, 60%, and 80%. Temperature-programmed desorption （TPD） experiments were used to estimate the activation energy for desorption of formaldehyde from the activated carbon. Results showed that the relative humidity had strongly influence on breakthrough curves of formaldehyde in the packed beds. The higher the relative humidity of gas mixtures through the packed beds was, the smaller the breakthrough time of formaldehyde became. The use of organosilane compounds to modify surfaces of the activated carbon can enhance the interaction between formaldehyde and the surfaces, and as a result, the breakthrough times of formaldehyde in the packed beds of the modified activated carbon were longer than that in the packed bed of the unmodified activated carbon.

Preparation of activated carbons and their adsorption properties for greenhouse gases:CH_4 and CO_2

Three kinds of activated carbons were prepared using coconut-shells as carbon precursors and characterized by XRD, FT-IR and texture property test. The results indicate that the prepared activated carbons were mainly amorphous and only a few impurity groups were adsorbed on their surfaces. The texture property test reveals that the activated carbons displayed different texture properties, especially the micropore size distribution. The adsorption capacities of the activated carbons were investigated by adsorbing CH4, CO2, N2 and O2 at 25 ？C in the pressure range of 0-200 kPa. The results reveal that all the activated carbons had high CO2 adsorption capacity, one of which had the highest CO2 adsorption value of 2.55 mmol/g at 200 kPa. And the highest adsorption capacity for CH4 of the activated carbons can reach 1.93 mmol/g at 200 kPa. In the pressure range of 0-200 kPa, the adsorption capacities for N2 and O2 were increased linearly with the change of pressure and K-AC is an excellent adsorbent towards the adsorption separation of greenhouse gases.

Preparation of mesoporous activated carbons from coal liquefaction residue for methane decomposition

Mesoporous activated carbons were prepared from direct coal liquefaction residue （CLR） by KOH activation method, and the experiments were carried out to investigate the effects of KOH/CLR ratio, solvent for mixing the CLR and KOH, and carbonization procedure on the resultant carbon texture and catalytic activity for catalytic methane decomposition （CMD）. The results showed that optimal KOH/CLR ratio of 2 ： 1; solvent with higher solubility to KOH or the CLR, and an appropriate carbonization procedure are conductive to improving the carbon pore structure and catalytic activity for CMD. The resultant mesoporous carbons show higher and more stable activity than microporous carbons. Additionally, the relationship between the carbon textural properties and the catalytic activity for CMD was also discussed.

A mini-review on the modeling of volatile organic compound adsorption in activated carbons: Equilibrium, dynamics, and heat effects

The research on the adsorption equilibria,kinetics,and increase in process temperature of the volatile organic compound(VOC)adsorption in porous materials ensures safe production,thereby reducing production costs and improving separation efficiency.Therefore,it is critical in predicting the entire adsorption process based on minimal or no experimental input of the adsorbate and adsorbent.We discuss,in this review,the factors that affect the adsorption performance of VOCs in activated carbons,including the adsorption equilibrium,adsorption kinetics,and exotherm during adsorption.Subsequently,the existing prediction models are summarized and compared concerning the adsorption equilibrium,adsorption kinetics,and exothermic process of adsorption.We then propose a new prediction model based on intermolecular interaction and provide an outlook toward the design and manipulation of efficient adsorbents for the VOC system.

Modified activated carbons with amino groups and their copper adsorption properties in aqueous solution

Activated carbons were prepared by two chemical methods and the adsorption of Cu(II) on activated carbons from aqueous solution containing amino groups was studied. The first method involved the chlorination of activated carbon following by substitution of chloride groups with amino groups, and the second involved the nitrilation of activated carbon with reduction of nitro groups to amino groups. Resultant activated carbons were characterized in terms of porous structure, elemental analysis, FTIR spectroscopy, XPS, Boehm titration,and p Hzpc. Kinetic and equilibrium tests were performed for copper adsorption in the batch mode. Also,adsorption mechanism and effect of p H on the adsorption of Cu(II) ions were discussed. Adsorption study shows enhanced adsorption for copper on the modified activated carbons, mainly by the presence of amino groups, and the Freundlich model is applicable for the activated carbons. It is suggested that binding of nitrogen atoms with Cu(II) ions is stronger than that with H+ions due to relatively higher divalent charge or stronger electrostatic force.

Preparation and electrochemical characterization of activated carbons by chemical-physical activation

A process was proposed based on the combination of chemical and physical activation for the production of activated carbons used as the electrode material for electric double layer capacitor (EDLC). By material characterization and electrochemical methods, the influences of the activitation process on the specific surface area, pore structure and electrochemical properties of the activated carbons were investigated. The results show that specific surface area, the mesopore volume, and the specific capacitance increase with the increase of the mass ratio of KOH to char (m(KOH)/m(char)) and the activation time, respectively. When m(KOH)/m(char) is 4.0, the specific surface area and the mesopore volume reach the maximum values, i.e. 1 960 m2/g and 0.308 4 cm3/g, and the specific capacitance is 120.7 F/g synchronously. Compared with the chemical activation, the activated carbons prepared by chemical-physical activation show a larger mesopore volume, a higher ratio of mesopore and a larger specific capacitance.

Sustainable Activated Carbons from Agricultural Residues Dedicated to Antibiotic Removal by Adsorption

The. objectives.of this study are to convert at laboratory s.cale agric.ultural residues into activated carbons （AC） with specific properties, to characterize them and to test them in adsorption reactor for tetracycline removal, a common antibiotic. Two new ACs were produced by direct activation with steam from beet pulp （BP-H2O） and peanut hu_lls （PH-H2O） in environmental friendly conditions BP-H2O and PH-H2Opresentcarbon content rangedcarbons with different intrinsic properties.

Preparation of activated carbons from mesophase pitch and their electrochemical properties

The influences of molar ratio of KOH to C and activated temperature on the pore structure and electrochemical property of porous activated carbon from mesophase pitch activated by KOH were investigated. The surface areas and the pore structures of activated carbons were analyzed by nitrogen adsorption, and the electrochemical properties of the activated carbons were studied using two-electrode capacitors in organic electrolyte. The results indicate that the maximum surface area of 3 190 m2/g is obtained at molar ratio of KOH to C of 5:1, the maximum specific capacitance of 122 F/g is attained at molar ratio of KOH to C of 4:1, and 800 ℃ is the proper temperature to obtain the maximum surface area and capacitance.

Influence of nitrogen hetero-substitution on the electrochemical performance of coal-based activated carbons measured in non-aqueous electrolyte

Nitrogen-containing carbons were prepared by modification of activated carbons.The modified carbons were used as electrode materials with improved electrochemical performance.Precursor anthracite was activated by KOH(KOH:anthracite= 1:1), modified by melamine or urea and then treated at 1173 K to obtain the modified carbons.The porous structure, the chemical composition and the electrochemical characteristics of the carbons were investigated by nitrogen sorption, XPS and electrochemical methods respectively.Electrochemical experiments were performed in an organic electrolytic solution of 1 M(C2H5)4NBF4/PC.The samples modified by the different methods showed differences in chemical composition that introduced varying degrees of electrochemical performance enhancement.The presence of nitrogen enhanced the electron donor properties and the surface wettability of the activated carbons:this ensured a sufficient utilization of the exposed surface for charge storage.

Removal of phenol by activated carbons prepared from palm oil mill effluent sludge

The study was attempted to produce activated carbons from palm oil mill effluent （POME） sludge. The adsorption capacity of the activated carbons produced was evaluated in aqueous solution of phenol. Two types of activation were followed, namely, thermal activation at 300, 500 and 800%, and physical activation at 150% （boiling treatment）. A control （raw POME sludge） was used to compare the adsorption capacity of the activated carbons produced. The results indicated that the activation temperature of 800℃ showed maximum absorption capacity by the activated carbon （POME 800） in aqueous solution of phenol. Batch adsorption studies showed an equilibrium time of 6 h for the activated carbon of POME 800. It was observed that the adsorption capacity was higher at lower values ofpH （2--3） and higher value of initial concentration of phenol （200--300 mg/L）, The equilibrium data were fitted by the Langmuir and Freundlich adsorption isotherms. The adsorption of phenol onto the activated carbon POME 800 was studied in terms of pseudo-first and second order kinetics to predict the rate constant and equilibrium capacity with the effect of initial phenol concentrations. The rate of adsorption was found to be better correlation for the pseudo-second order kinetics compared to the first order kinetics.

Effect of Adding Microwave Absorber on Structures and Properties of Hypercoal-Based Activated Carbons

Using lignite-based hypercoal as raw material, KOH as activator and CuO as microwave absorber, we prepared hypercoal-based activated carbons by microwave-assisted activation. The pore structure and the electrochemical performance of the activated carbons were tested, and the effects of adding CuO in the activation reaction process were also investigated. The activated carbons prepared were characterized by nitrogen adsorption-desorption, X-ray diffraction (XRD) and scanning electron microscopy (SEM). The specific surface area and mesoporous ratio of the hypercoal-based activated carbon are 1257 m2/g and 55.4%, respectively. When the activated carbons are used as the electrode materials, the specific capacitance reaches 309 F/g in 3 M KOH electrolyte. In comparison with those prepared without CuO absorber, the specific capacitance increases by 11.6%. It was proved that the addition of microwave absorber in microwave-assisted activation was a low-cost method for rapidly preparing activated carbon, and it could effectively promote the development of the pore structure and improve its electrochemical performance.

Granular activated carbons from palm nut shells for gold di-cyanide adsorption

Granular activated carbons were produced from palm nut shells by physical activation with steam. The proximate analysis of palm nut shells was investigated by thermogravimetric analysis, and the adsorption capacity of the activated carbons, produced as a result of shell pyrolysis at 600℃ followed by steam activation at 900℃ in varying activation times, was evaluated using nitrogen adsorption at 77 K. Applicability of the activated carbons for gold dicyanide adsorption was also investigated. Increasing the activation hold time with the attendant increase in the degree of carbon burn-off results in a progressive increase in the surface area of the activated carbons, reaching a value of 903.1 m2/g after activation for 6 h. The volumes of total pores, mieropores, and mesopores in the activated carbons also increase progressively with the increasing degree of carbon burn-off, resulting from increasing the activation hold time. The gold di-cyanide adsorption of the activated carbons increases with the rise of pore volume of the activated carbons. The gold di-cyanide adsorption of palm nut shell activated carbon obtained after 6-h activation at 900℃ is superior to that of a commercial activated carbon used for gold di-cyanide adsorption.

PREPARATION AND CHARACTERIZATION OF POLYMER-BASED SPHERICAL ACTIVATED CARBONS

A series of spherical activated carbons(SACs)with different pore structures were prepared from chloromethylated polydivinylbenzene by ZnCl_2 activation.The effects of activation temperature and retention time on the yield and textural properties of the resulting SACs were studied.All the SACs are generated with high yield of above 65% and exhibit relatively high mesopore fraction(me%)of 35.7%-43.6% compared with conventional activated carbons.The sample zlc28 prepared at 800℃for 2 h has the largest BET surf...