High adsorption selectivity of activated carbon and carbon molecular sieve boosting CO_(2)/N_(2) and CH_(4)/N_(2) separation

Flue gas and coal bed methane are two important sources of greenhouse gases.Pressure swing adsorption process has a wide range of application in the field of gas separation,and the selection of adsorbent is crucial.In this regard,in order to assess the better adsorbent for separating CO_(2) from flue gas and CH_(4) from coal bed methane,adsorption isotherms of CO_(2),CH_(4) and N_(2) on activated carbon and carbon molecular sieve are measured at 303.15,318.15 and 333.15 K,and up to 250 kPa.The experimental data fit better with Langmuir 2 compared to Langmuir 3 and Langmuir-Freundlich models,and Clausius-Clapeyron equation was used to calculate the isosteric heat.Both the order of the adsorbed amount and the adsorption heat on the two adsorbents are CO_(2)>CH_(4)>N_(2).The adsorption kinetics are calculated by the pseudo-first kinetic model,and the order of adsorption rates on activated carbon is N_(2)-CH_(4)>CO_(2),while on carbon molecular sieve,it is CO_(2)-N_(2)>CH_(4).It is shown that relative molecular mass and adsorption heat are the primary effect on kinetics for activated carbon,while kinetic diameter is the main resistance factor for carbon molecular sieve.Moreover,the adsorption selectivity of CH_(4)/N_(2) and CO_(2)/N_(2) were estimated with the ideal adsorption solution theory,and carbon molecular sieve performed best at 318.15 K for both CO_(2) and CH_(4) separation.The study suggested that activated carbon is a better choice for separating flue gas and carbon molecular sieve can be a strong candidate for separating coal bed methane.

In-situ construction of abundant active centers on hierarchically porous carbon electrode toward high-performance phosphate electrosorption: Synergistic effect of electric field and capture sites

Phosphate removal is crucial for eutrophication control and water quality improvement.Electro-assisted adsorption,an eco-friendly elec-trosorption process,exhibited a promising potential for wastewater treatment.However,there are few works focused on phosphate electro-sorption,and reported electrodes cannot attach satisfactory removal capacities and rates.Herein,electro-assisted adsorption of phosphate via in-situ construction of La active centers on hierarchically porous carbon(LaPC)has been originally demonstrated.The resulted LaPC composite not only possessed a hierarchically porous structure with uniformly dispersed La active sites,but also provided good conductivity for interfacial electron transfer.The LaPC electrode achieved an ultrahigh phosphate electrosorption capability of 462.01 mg g^(-1) at 1 V,outperforming most existing electrodes.The superior phosphate removal performance originates from abundant active centers formed by the coupling of electricfield and capture sites.Besides,the stability and selectivity toward phosphate capture were maintained well even under comprehensive conditions.Moreover,a series of kinetics and isotherms models were employed to validate the electrosorption process.This work demonstrates a deep understanding and promotes a new level of phosphate electrosorption.

Fate and Behavior of Tetracycline Resistance Genes in Activated Carbon Adsorption

The accessibility of tetracycline resistance gene (tetG) into the pores of activated carbon (AC), as well as the impact of the pore size distribution (PSD) of AC on the uptake capacity of tetG, were investigated using eight types of AC (four coal-based and four wood-based). AC showed the capability to admit tetG and the average reduction of tetG for coal-based and wood-based ACs at the AC dose of 1 g·L-1 was 3.12 log and 3.65 log, respectively. The uptake kinetic analysis showed that the uptake of the gene followed the pseudo-second-order kinetics reaction, and the uptake rate constant for the coal-based and wood-based ACs was in the range of 5.97 × 10-12 - 4.64 × 10-9 and 7.02 × 10-11 - 1.59 × 10-8 copies·mg-1·min-1, respectively. The uptake capacity analysis by fitting the obtained experiment data with the Freundlich isotherm model indicated that the uptake constant (KF) values were 1.71 × 103 - 8.00 × 109 (copies·g-1)1-1/n for coal-based ACs and 7.00 × 108 - 3.00 × 1010 (copies·g-1)1-1/n for wood-based ones. In addition, the correlation analysis between KF values and pore volume as well as pore surface at different pore size regions of ACs showed that relatively higher positive correlation was found for pores of 50 - 100 Å, suggesting ACs with more pores in this size region can uptake more tetG. The findings of this study are valuable as reference for optimizing the adsorption process regarding antibiotic resistance-related concerns in drinking water treatment.

Theoretical and Experimental Study on the Adsorption and Desorption of Methane by Granular Activated Carbon at 25℃

A theoretical and experimental study was conducted to accurately determine the amount of adsorption and desorption of methane by various Granular Activated Carbon （GAC） under different physical conditions. To carry out the experiments, the volumetric method was used up to 500 psia at constant temperature of 25℃. In these experiments, adsorption as well as desorption capacities of four different GAC in the adsorption of methane, the major constituent of natural gas, at various equilibrium pressures and a constant temperature were studied. Also, various adsorption isotherm models were used to model the experimental data collected from the experiments. The accuracy of the results obtained from the adsorption isotherm models was compared and the values for the regressed parameters were reported. The results shows that the physical characteristics of activated carbons such as BET surface area, micropore volume, packing density, and pore size distribution play an important role in the amount of methane to be adsorbed and desorbed.

Adsorption and desorption phenomena on thermally annealed multi-walled carbon nanotubes by XANES study

The multi-walled carbon nanotubes(MWCNTs) studied in this work were synthesized by the catalytic chemical vapor deposition(CCVD) process, and were thermally annealed by the hot filament plasma enhanced(HF PE) method at 550℃ for two hours.The x-ray absorption near edge structure(XANES) technique was used to investigate the adsorption and desorption phenomena of the MWCNTs at normal and grazing incidence angles.The adsorbates were found to have different sensitivities to the thermal annealing.The geometry of the incident beam consistently gave information about the adsorption and desorption phenomena.In addition, the adsorption of non-intrinsic potassium quantitatively affected the intrinsic adsorbates and contributed to increase the conductivity of the MWCNTs.The desorption of potassium was almost 70% greater after the thermal annealing.The potassium non-intrinsic adsorbates are from a physisorption mechanism whereas the intrinsic adsorbates result from chemisorption.

Experimental and Theoretical Study of the Effect of Moisture on Methane Adsorption and Desorption by Activated Carbon at 273.5 K

Adsorption and desorption of methane by activated carbon （AC） at constant temperature and at various pressures were investigated. The effect of moisture was also studied. A volumetric method was used, up to 40 bar, at a temperature of 273.5 K. Results of a dry AC sample were compared with those obtained from a moist sample and two different ACs with different physical and surface properties were used. As expected, the results showed that the existence of moisture, trapped in the AC pores, could lead to a decrease in the amount of methane adsorbed and a decrease in the amount of methane delivered during desorption. To model the experimental results, a large variety of adsorption isotherms were used. The regressed parameters for the adsorption isotherms were obtained using the experimental data generated in the present study. The accuracy of the results obtained from the different adsorption isotherms was favorably compared.

SEPARATION OF Re AND Mo BY ADSORPTION OF ACTIVE CARBON

Separation of Re and Mo by adsorption of active carbon has been studied. The results show that Re and Mo can be separated effectively by adjusting the pH value. As pH】8.2. the coefficient of separation SRc/Mo】3.042. The adsorption isotherm for Re conforms to the Freundlich formula.

Ultra-high specific surface area activated carbon from Taihu cyanobacteria via KOH activation for enhanced methylene blue adsorption

Cyanobacteria-based activated carbon(CBAC)was successfully prepared by pyrolysis-activation of Taihu cyanobacteria.When the impregnation ratio and activated temperature were 2 and 800-C,respectively,the optimal CBACs possessed an ultra-high specific surface(2178.90 m^(2)·g^(-1))and plenty of micro-and meso-pores,as well as a high pore volume(1.01 cm^(3)·g^(-1)).Ascribed to ultra-high surface area,π-π interaction,electrostatic interaction,as well as hydrogen-bonding interactions,the CBACs displayed huge superiority in efficient dye removal.The saturated methylene blue adsorption capacity by CBACs could be as high as 1143.4 mg·g^(-1),superior to that of other reported biomass-activated carbons.The adsorption was endothermic and modeled well by the pseudo-second-order kinetic,intra-particle diffusion,and Langmuir models.This work presented the effectiveness of Taihu cyanobacteria adsorbent ascribed to its super large specific surface area and high adsorption ability.

Preparation of activated carbon from sunflower straw through H_(3)PO_(4) activation and its application for acid fuchsin dye adsorption

With the development circular economy, the use of agricultural waste to prepare biomass materials to remove pollutants has become a research hotspot. In this study, sunflower straw activated carbon (SSAC) was prepared by the one-step activation method, with sunflower straw (SS) used as the raw material and H3PO4 used as the activator. Four types of SSAC were prepared with impregnation ratios (weight of SS to weight of H3PO4) of 1:1, 1:2, 1:3, and 1:5, corresponding to SSAC1, SSAC2, SSAC3, and SSAC4, respectively. The adsorption process of acid fuchsin (AF) in water using the four types of SSAC was studied. The results showed that the impregnation ratio significantly affected the structure of the materials. The increase in the impregnation ratio increased the specific surface area and pore volume of SSAC and improved the adsorption capacity of AF. However, an impregnation ratio that was too large led to a decrease in specific surface area. SSAC3, with an impregnation ratio of 1:3, had the largest specific surface area (1 794.01 m2/g), and SSAC4, with an impregnation ratio of 1:5, exhibited the smallest microporosity (0.052 7 cm3/g) and the largest pore volume (2.549 cm3/g). The adsorption kinetics of AF using the four types of SSAC agreed with the quasi-second-order adsorption kinetic model. The Langmuir isotherm model was suitable to describe SSAC3 and SSAC4, and the Freundlich isotherm model was appropriate to describe SSAC1 and SSAC2. The result of thermodynamics showed that the adsorption process was spontaneous and endothermic. At 303 K, SSAC4 showed a removal rate of 97.73% for 200-mg/L AF with a maximum adsorption capacity of 2 763.36 mg/g, the highest among the four types of SSAC. This study showed that SAAC prepared by the H3PO4-based one-step activation method is a green and efficient carbon material and has significant application potential for the treatment of dye-containing wastewater.

Chemically activated carbon nanofibers for adsorptive removal of bisphenol-A:Batch adsorption and breakthrough curve study

Activated carbon nanofibers(ACNFs)with small diameter can significantly increase the accessibility of intra pores and accelerate adsorption of molecules from water.In this study,ACNFs were made by blending K_(2)CO_(3)or ZnCl_(2)as the activating agent into the polyacrylonitrile(PAN)in dimethylformamide solution for electrospinning prior to pyrolysis.Bisphenol-A(BPA),an endocrine disruption pollutant,is widely applied in the production of polycarbonate plastics and epoxy resins.Accordingly,BPA is often used as a model contaminant commonly removed via adsorption.Batch adsorption studies were used to evaluate the kinetics and adsorption capacity of the ACNFs.Redlich-Peterson(R-P)and Langmuir models were found to fit the isotherm of BPA adsorption better than Freundlich model,showing the homogeneous nature of the PAN originated ACNFs.The adsorption kinetics was better described by the pseudo second-order model than that by the pseudo first-order model.The fitting by intraparticle diffusion model indicates the adsorption of BPA onto ACNFs is mainly controlled by pore diffusion.High pH value and ionic strength reduced BPA adsorption from aqueous solution.The breakthrough curves studied in two different fixed bed systems(cross flow bed system and packed flow bed system)confirmed the scalability of BPA removal by ACNFs in dynamic adsorption processes.The modified dose-response model predicted well the fixed-bed outlet concentration profiles.

Optimizing Methylene Blue Removal from Textile Effluents: Comparative Study of Adsorption Efficiency Using Raw and Activated Carbon Derived from Gmelina Wood Wastes

This research investigates the efficacy of activated Gmelina Wood Sawdust (GWS) as an adsorbent for the removal of methylene blue (MB) dye from aqueous solutions, in comparison with raw GWS. The study employs laboratory experiments to assess the percentage of dye removal across various temperature and pH conditions. The adsorption process is scrutinized under different parameters, encompassing contact time, initial dye concentration, adsorbent dosage, temperature, and pH. Results demonstrate that activated GWS surpasses its raw counterpart, showcasing superior MB dye removal percentages. Extended contact times increased initial dye concentrations, and higher adsorbent dosages contribute positively to removal efficiency, while temperature exhibits an inverse relationship with dye removal. Optimal adsorption occurs at a pH of 7.0, aligning with the adsorbent’s zero-point charge (pHzpc), underscoring the role of surface charge in the adsorption process. This study underscores the potential of activated GWS as an economical and promising adsorbent material for addressing pollutants. Furthermore, the utilization of activated carbon derived from abundant agricultural waste underscores an environmentally conscious approach to adsorption applications. The ability to tailor the size and properties of activated carbon particles opens avenues for optimizing adsorption capabilities, thereby presenting opportunities for enhanced water treatment solutions.

Characteristic and mercury adsorption of activated carbon produced by CO_2 of chicken waste

Preparation of activated carbon from chicken waste is a promising way to produce a useful adsorbent for Hg removal. A three-stage activation process （drying at 200℃, pyrolysis in N2 atmosphere, followed by CO2 activation） was used for the production of activated samples. The effects of carbonization temperature （409-4500℃）, activation temperature （700-900℃）, and activation time （1-2.5 h） on the physicochemical properties （weight-loss and BET surface） of the prepared carbon wereinvestigated. Adsorptive removal of mercury from real flue gas onto activated carbon has been studied. The activated carbon from chicken waste has the same mercury capacity as commercial activated carbon （Darco LH） （Hg^v： 38.7% vs. 53.5%, Hg^0： 50.5% vs. 68.8%）, although its surface area is around 10 times smaller, 89.5 m^2/g vs. 862 m^2/g. The low cost activated carbon can be produced from chicken waste, and the procedure is suitable.

Adsorption and Regeneration of Volatile Organic Compounds(VOCs)on Coal-Based Activated Carbon by Ferric Nitrate Modification

In this study,the Heishan coal was used to prepare a series of activated carbon(AC)samples via a vapor deposition method.The effects of the Fe(NO_(3))3/coal weight ratio on the physicochemical properties of the activated carbon were systematically investigated,and the AC samples were analyzed by the N2 adsorption-desorption technique,the scanning electron microscopy,the X-ray diffraction,the Raman spectroscopy,and the Fourier transform infrared spectroscopy.Furthermore,the adsorption properties of ethyl acetate were investigated.The results indicated that as the Fe(NO_(3))3/coal mass ratio increased from 1:8 to 1:2,the specific surface area,the total pore volume and the micropore volume initially increased and then decreased.The specific surface area increased from 560.86 m^(2)/g to 685.90 m^(2)/g,and then decreased to 299.56 m^(2)/g.The total pore volume and micropore volume increased from 0.29 cm^(3)/g and 0.17 cm^(3)/g to 0.30 cm^(3)/g and 0.22 cm^(3)/g,and then decreased to 0.16 cm^(3)/g and 0.10 cm^(3)/g,respectively.The optimized ratio was 1:8.During the activation process,iron ions infiltrated the activated carbon to promote the development of the pore structure,the pore size of which was between 2.5 nm and 3 nm in daimeter.This approach could enhance the capacity for adsorption of ethyl acetate.It is worth noting that the ACs displaying the largest specific surface area and total pore volume(685.90 m^(2)/g and 0.30 cm^(3)/g)were formed under the optimized activation conditions(950℃,20%(volume)of CO_(2),ratio 1:5),and the maximum AC capacity for adsorption of ethyl acetate was 962.62 mg/g.After seven repeated thermal regeneration experiments,the saturated AC adsorption capacity was still above 90%.

Bromate removal by activated carbon adsorption:material selection and impact factors study

Studies are conducted by using activated carbon process aimed at bromate removal from the raw water.Screening of activated carbon for bromate removal was performed in different activated carbons.GAC Merck possesses the highest iodine number and surface area,the highest number of basic groups and Vmeso,thereby contains the highest adsorption velocity and adsorption capacity.Impact factors of bromate removal on activated carbon were studied.Through static absorption experiments we studied the effect of adsorption time,pH,temperature,anions and organic matter on bromate removal.With the decrease of pH,removal of bromate enhanced,suggests that it may be possible to increase bromate reduction through pH control.The increase of temperature will be favorable to adsorption of bromate on activated carbon.Anions and organic matter can inhibit the adsorption of bromate on activated carbon through competing active sites.Bromate removal can be improved by controlling key water quality parameters.

Adsorption and Desorption of Gold on the Magnetic Activated Carbon

Adsorption and desorption of gold on the magnetic activated carbon (MAC) were investigated The adsorption rate of gold is higher than that of conventional coconut carbon in cyanide leach solution The loading gold can be easily desorbed as coconut carbon. Crushed fine magnetic carbon can be selected by a magnetic separator, It is suggested that the MAC can be used in carbon-in-pulp (CIP)process for increasing the recovery rate of gold

Adsorption of Cu and Ni Ions from Aqueous Solutions by Commercial Activated Carbon and the Reutilization in Glass Coloration

Toxic Cu(Ⅱ) and Ni(Ⅱ) ions in aqueous solutions were adsorbed by microporous activated carbon(AC). The adsorption isotherm and kinetics correlation coefficients indicate that the adsorption of Cu(Ⅱ) and Ni(Ⅱ) ions on the AC fits the pseudo second-order rate model and Langmuir adsorption model. The used AC adsorbents containing the adsorbed Cu and Ni ions were used as colorant in glass preparation. The coloration effect of Cu ions was influenced by the carbon absorbent included in the glass batch due to the reduction phenomenon, while the coloration of Ni ions was not affected.

Characterization and Methanol Adsorption of Walnutshell Activated Carbon Prepared by KOH Activation

Walnut-shellactivated carbons（WSACs）were prepared by the KOH chemicalactivation.The effects of carbonization temperature,activation temperature,and ratio of KOH to chars on the pore development of WSACs were investigated.Fourier transform infrared spectroscopy（FTIR）,X-ray powder diffraction（XRD）,and scanning electron microscopy（SEM）were employed to characterize the microstructure and morphology of WSACs.Methanoladsorption performance onto the optimalWSAC and the coal-based AC were also investigated.The results show that the optimalpreparation conditions are a carbonization temperature of 700 ℃,an activation temperature of 700 ℃,and a mass ratio of 3.The BET surface area,the micropore volume,and the micropore volume percentage of the optimalWASC are 1636 m^2/g,0.641 cm^3/g and 81.97%,respectively.There are a lot of micropores and a certain amount of meso-and macropores.The characteristics of the amorphous state are identified.The results show that the optimalWSAC is favorable for methanoladsorption.The equilibrium adsorption capacity of the optimalWSAC is 248.02mg/g.It is shown that the equilibrium adsorption capacity of the optimalWSAC is almost equivalent to that of the common activated carbon.Therefore the optimalWSAC could be a potentialadsorbent for the solar energy adsorption refrigeration cycle.

Cost Effective Adsorption of Aluminium and Iron from Synthetic and Real Wastewater by Rice Hull Activated Carbon (RHAC)

The adsorption of aluminium(III) and iron(III) ions from their single and binary systems, by RHAC was investigated in a batch system. The activated carbon prepared from rice hulls was characterized by scanning electron microscopy and Fourier transformation infrared techniques. Batch adsorption experiments were performed under different operating conditions including pH (2 - 5), adsorbent dosage (0.5 - 2.0 g/l), initial ion concentration (5 - 100 mg/l), and contact time (30 - 240 min). The equilibrium time for maximum ions removal was found to be 180 min in single and binary ions systems. The kinetics of adsorption was evaluated using the pseudo-first order, pseudo-second order and Elovich kinetic models. The Langmuir, Freundlich and Temkin equilibrium models were applied to the adsorption experimental data. Real wastewater samples were collected from different locations to investigate the efficiency of rice hull activated carbon in treating real samples. The real wastewater samples were treated with the activated carbon prepared from rice hulls and a commercial activated carbon. The results showed that the activated carbon prepared in the present work was more efficient in the removal of aluminium and iron from real wastewater as compared to the commercial activated carbon which is more advantageous considering both economics and environmental parameters.

Adsorption of acid and basic dyes by sludge-based activated carbon:Isotherm and kinetic studies

A batch experiment was conducted to investigate the adsorption of an acid dye(Acid Orange 51) and a basic dye(Safranine) from aqueous solutions by the sludge-based activated carbon(SBAC). The results show that the adsorption of Acid Orange 51 decreases at high p H values, whereas the uptake of Safranine is higher in neutral and alkaline solutions than that in acidic conditions. The adsorption time needed for Safranine to reach equilibrium is shorter than that for Acid Orange 51. The uptakes of the dyes both increase with temperature increasing, indicating that the adsorption process of the dyes onto SBAC is endothermic. The equilibrium data of the dyes are both best represented by the Redlich-Peterson model. At 25 °C, the maximum adsorption capacities of SBAC for Acid Orange 51 and Safranine are 248.70 mg/g and 525.84 mg/g, respectively. The Elovich model is found to best describe the adsorption process of both dyes, indicating that the rate-limiting step involves the chemisorption. It can be concluded that SBAC is a promising material for the removal of Acid Orange 51 and Safranine from aqueous solutions.

Adsorption of residual amine collector HAY from aqueous solution by refined carbon from coal fly ash and activated carbon

Refined carbon(RC) derived from coal fly ash(CFA) as well as powdered activated carbon(PAC) was investigated as adsorbent to remove residual amine collector HAY from aqueous solution.The RC and PAC were characterized by scanning electron microscopy(SEM),surface area measurement,Zeta potential measurement and Fourier transform infrared(FTIR) spectroscopy.The effect factors and mechanisms of HAY adsorption onto RC and PAC were studied in detail.The results show that the experimental kinetic data agree well with the pseudo second-order equation,and the Langmuir isotherm model is found to be more appropriate to explicate the experimental equilibrium isotherm results than the Freundlich model.The adsorption capacities of PAC and RC increase with pH.It is found that alkaline condition is conducive to the adsorption of HAY onto PAC and RC and the adsorption efficiency of RC is close to PAC at pH near 11.Zeta potential variation of adsorbents suggests that HAY generates electrostatic adsorption onto RC and PAC.FTIR analysis shows that the adsorption is dominantly of a physical process.The Box-Behnken design optimization conditions of process are RC 1 g/L,pH 11,temperature 302 K and initial HAY concentration 100 mg/L.Under these conditions,the measured adsorption ratio and adsorption capacity are 87.91%and 87.91 mg/g,respectively.Thus,the RC is considered to be a potential adsorbent for the removal of residual amine from aqueous solution.