A homogeneous atmospheric pressure air plasma in a 10 mm gap based on a three-electrode configuration

Generation of atmospheric pressure homogeneous air plasma in a large gap(>4 mm)is a challenge.In this study,an atmospheric pressure homogeneous air plasma generated in a gap up to 10 mm is reported,which is based on a three-electrode configuration,where a high-voltage(HV)electrode and a middle electrode form a surface dielectric barrier discharge(S-DBD),and together with the ground electrode form the main volume discharge.High-speed photographs confirm that the discharge in the main gap is homogeneous.The gas temperature of the plasma estimated from the N_(2)(C^(3)∏_(u)-B^(3)∏_(g))(Δv=-2)emission is about 320 K,which is close to room temperature.A detailed analysis shows that the discharge ignited between the HV electrode and the middle electrode is serving as an electron source,and the electrons deposited on the dielectric plate are due to the S-DBD along with the applied voltage generating a driving force,which results in a high concentration of seed electrons in the main gap and induces the homogeneous plasma.Further analysis shows that the electric field in the main gap is only about18.45 k V·cm^(-1),which is much lower than the typical breakdown electric field of 30 k V·cm^(-1)for atmospheric pressure air discharge.

Effect of Thermal Treatment on the Grain Growth of Nanostructured YSZ Thermal Barrier Coating Prepared by Air Plasma Spraying

A nanostructured thermal barrier coating is prepared by air plasma spraying using the 8wt% Y_2O_3 partially stabilized zirconia nano-powder with an average grain size of 40 nm. The microstructure and phase composition of feedstock nano-powder and coating are investigated using SEM, TEM and XRD. It is found that the as-sprayed zirconia coating has an average grain size of 67 nm and mainly consistes of metastable tetragonal phase, together with some monoclinic phase and tetragonal phase. Thermal treatment results show that the grains of the nanostructured coating grow slightly below 900℃, whereas over 1000℃ the gains grow rapidly and monoclinic phase noticeably appeares.

Effects of Atmospheric Pressure Air Plasma Pretreatment on the Seed Germination and Early Growth of Andrographis paniculata

The objective of this paper is to demonstrate whether air plasma can change the seed germination characteristics, seedling emergence, as well as biochemical reactivity, in Andrographis paniculata （A. paniculata） seedlings by modifying the seed coat and finding a beneficial treatment dose. Eight treatment doses and one control were used to conduct electrical conductivity determination, a germination test, a seedling emergence test and a biochemical assay. The results showed that after being treated with air plasma excited at 5950 V for 10 s, the perme- ability of the seeds was improved significantly, resulting in the acceleration of seed germination and seedling emergence. In the meantime, the catalase activity and catalase isoenzyme expression were also improved, while the malondialdehyde content in the seedlings was decreased （which means greater counteraction with environmental stress）. After being treated with 4250 V for 10 s and 5950 V for 20 s, the seed germination was enhanced, but without an obvious change in seedUng emergence. However, after treatment with 3400 V for 20 s and 5100 V for 10 s, the permeability of the seeds was decreased, resulting in a delay in seedling emergence. These results indicate that air plasma can change the physiological and biochemical characteristics of Andrographis paniculata seeds by modifying the seed coat, combined with the effects of the active plasma species, and that different treating doses have different effects.

The Effect of Air Plasma on Sterilization of Escherichia coli in Dielectric Barrier Discharge

In this work, a Dielectric Barrier Discharge （DBD） air plasma was used to sterilize Escherichia eoli （E. coli） on the surface of medical Polyethylene Terephthalate （PET） film. The leakage of cellular DNA and protein by optical absorbance measurement at 260 nm and 280 nm, together with transmission electron microscopy （TEM） about cell morphology were performed after sterilization to analyse inactivation mechanisms. The results indicated that the DBD air plasma was very effective in E. coli sterilization. The plasma germicidal efficiency depended on the plasma treatment time, the air-gap distance, and the applied voltage. Within 5 min of plasma treatment, the germicidal efficiency against E. coli could reach 99.99%. An etching action on cell membranes by electrons, ions and radicals is the primary mechanism for DBD air plasma sterilization, which leads to the effusion of cellular contents （DNA and protein） and bacterial death.

Cold atmospheric-pressure air plasma treatment of C6 glioma cells:effects of reactive oxygen species in the medium produced by the plasma on cell death

An atmospheric-pressure air plasma is employed to treat C6 glioma cells in vitro. To elucidate on the mechanism causing cell death and role of reactive species （RS） in the medium produced by the plasma, the concentration of the long-lived RS such as hydrogen peroxide, nitrate, and ozone in the plasma-treated liquid （phosphate-buffered saline solution） is measured. When vitamin C is added to the medium as a ROS quencher, the viability of C6 glioma cells after the plasma treatment is different from that without vitamin C. The results demonstrate that reactive oxygen species （ROS） such as H2O2, and O3 constitute the main factors for inactivation of C6 glioma cells and the reactive nitrogen species （RNS） may only play an auxiliary role in cell death.

Thermodynamic and Transport Properties of Real Air Plasma in Wide Range of Temperature and Pressure

Air plasma has been widely applied in industrial manufacture. In this paper, both dry and humid air plasmas＇ thermodynamic and transport properties are calculated in temperature 300 100000 K and pressure 0.1-100 atm. To build a more precise model of real air plasma, over 70 species are considered for composition. Two different methods, the Gibbs free energy minimization method and the mass action law method, are used to deternfinate the composition of the air plasma in a different temperature range. For the transport coefficients, the simplified Chapman-Enskog method developed by Devoto has been applied using the most recent collision integrals. It is found that the presence of CO2 has almost no effect on the properties of air plasma. The influence of H2O can be ignored except in low pressure air plasma, in which the saturated vapor pressure is relatively high. The results will serve as credible inputs for computational simulation of air plasma.

The Mutation Breeding and Mutagenic Effect of Air Plasma on Penicillium Chrysogenum

Low temperature air plasma was used as the mutation tool for penicillin-producing strain Penicillium chrysogenum. The discharge conditions were RF power of 360 W, temperature of 40℃ in a sealed chamber, and pressure of 10 Pa to 30 Pa. The result showed that the kinetics of the survival rate followed a typical saddle-shaped curve. Based on a statistic analysis, at the treating duration of 10 min, the positive mutation rate was as high as 37.5% while the negative mutation rate was low. The colonial morphology changed obviously when the plasma treating duration reached or exceeded 45 min. After both primary and secondary screening, a mutant designated as aPc051310 with high productivity of penicillin was obtained, and a strong mutagenic effect on P. chrysogenurn was observed in the process. It was proved that after five generations, the mutant aPc051310 still exhibits a high productivity. All the results prove that the plasma mutation method could be developed as a convenient and effective tool to breed high-yield strains in the fermentation industry, while expanding the plasm application at the same time.

Numerical Analysis of MHD Accelerator with Non-Equilibrium Air Plasma

Magnetohydrodynamic （MHD） accelerator is proposed as a next generation propulsion system. It can be used to increase the performance of a propulsion system. The objective of this study is to investigate the performance of MHD accelerator using non-equilibrium air plasma as working gas. In this study, the fundamental performance of MHD accelerator such as flow performance and electrical performance is evaluated at different levels of applied magnetic field using I-D numerical simulation. The numerical simulation is developed based on a set of differential equations with MHD approximation. To solve this set of differential equations the MacCormack scheme is used. A specified channel designed and developed at NASA Marshall Space Flight Centre is used in the numerical simulation. The composition of the simulated air plasma consists of seven species, namely, N2, N, O2, O, NO, NO＋, and e-. The performance of the non-equilibrium MHD accelerator is also compared with the equilibrium MHD accelerator.

Numerical and Experimental Investigation of Electron Beam Air Plasma Properties at Moderate Pressure

Large size of air plasma at near atmospheric pressure has specific effects in aerospace applications. In this paper, a two dimensional multi-fluid model coupled with Monte Carlo （MC） model is established, and some experiments were carried out to investigate the characteristics of electron beam air plasma at pressure of 100-170 Torr. Based on the model, the properties of electron beam air plasma are acquired. The electron density is of the order of 1016 m-3 and the longitudinal size can exceed 1.2 m. The profiles of charged particles demonstrate that the oxygen molecule is very important for air plasma and its elementary processes play a key role in plasma equilibrium processes. The potential is almost negative and a very low potential belt is observed at the edge of plasma acting as a protection shell. A series of experiments were carried out in a low pressure vacuum facility and the beam plasma densities were diagnosed. The experimental results demonstrate that electron density increased with the electron beam energy, and the relatively low pressure was favorable for gaining high density plasma. Hence in order to achieve high density and large size plasma, it requires the researchers to choose proper discharge parameters.

Quantitative Determination of Density of Ground State Atomic Oxygen from Both TALIF and Emission Spectroscopy in Hot Air Plasma Generated by Microwave Resonant Cavity

Two experimental techniques have been used to quantify the atomic oxygen density in the case of hot air plasma generated by a microwave （MW） resonant cavity. The latter operates at a frequency of 2.45 GHz inside a cell of gas conditioning at a pressure of 600 mbar, an injected air flow of 12 L/min and an input MW power of 1 kW. The first technique is based on the standard two photon absorption laser induced fluorescence （TALIF） using xenon for calibration but applied for the first time in the present post discharge hot air plasma column having a temperature of about 4500 K near the axis of the nozzle. The second diagnostic technique is an actinometry method based on optical emission spectroscopy （OES）. In this case, we compared the spectra intensities of a specific atomic oxygen line （844 nm） and the closest wavelength xenon line （823 nm）. The two lines need to be collected under absolutely the same spectroscopic parameters. The xenon emission is due to the addition of a small proportion of xenon （1% Xe） of this chemically inert gas inside the air while a further small quantity of H2 （2~） is also added in the mixture in order to collect OH（A- X） and NH（A-X） spectra without noise. The latter molecular spectra are required to estimate gas and excitation temperatures. Optical emission spectroscopy measurements, at for instance the position z=12 mm on the axis plasma column that leads to a gas measured temperature equal to 3500 K, an excitation temperature of about 9500 K and an atomic oxygen density 2.09× 1017＋ 0.2×1017 cm-3. This is in very good agreement with the TALIF measurement, which is equal to 2.0×101T cm-3.

Sensitivity of two drug-resistant bacteria to low-temperature air plasma in catheterassociated urinary tract infections under different environments

The high incidence of catheter-associated urinary tract infections,which are dominated by drugresistant bacteria,has attracted an increasing number of researchers interested in solving this public health problem.The purpose of this study was to explore the killing effect of lowtemperature air plasma(LTAP)on extended-spectrum beta-lactamase-producing Escherichia coli and high level gentamycin resistance enterococci under two simulated environments in vitro.The results showed that the survival rate of these two kinds of bacteria decreased to less than20%after being treated by LTAP in different environments for 5 min.A comparison of the LTAP treatments showed that the killing efficacy of the two kinds of bacteria in the early stage(0-1 min)was up to 50%.Moreover,the results of transmission electron microscopy,reactive nitrogen species measurement,and a temperature test indicated that the bactericidal effect of the LTAP treatment on the two kinds of bacteria worked through the destruction of the ribosome and other organelles inside the bacteria,rather than the thermal effect,to achieve sterilization.

Oxidation Performance of Ytterbium Disilicate/Silicon Environmental Barrier Coating via Optimized Air Plasma Spraying

Environmental barrier coatings (EBCs) play a critical role in mitigating the degradation of SiCf/SiC ceramic matrix composites (CMCs) in complex combustion environment, and improve the service life of thermal engine components. In this paper, by adjusting the parameters of atmospheric plasma spraying (APS), the spraying process of ytterbium disilicate (Yb2Si2O7) under a lower power has been optimized. A two-layer EBC system consisting of ytterbium disilicate and silicon is prepared on the SiCf/SiC composite substrate by using optimized technological parameters. The thermal resistance and water oxygen corrosion resistance of such two-layer EBC system are investigated. The results indicate that the current ytterbium disilicate/silicon EBC system exhibits good phase stability, excellent water vapor and oxygen corrosion resistance. However, the exposed silicon bonding layer tends to generate an excessive thermal growth oxide (TGO) layer known as SiO2, leading to an early spallation of the coating.

A numerical simulation study on active species production in dense methane-air plasma discharge

Recently, low-temperature atmospheric pressure plasmas have been proposed as a potential type of ＇reaction cartier＇ for the conversion of methane into value-added chemicals. In this paper, the multi-physics field coupling software of COMSOL is used to simulate the detailed discharge characteristics of atmospheric pressure methane-air plasma. A two-dimensional axisymmetric fluid model is constructed, in which 77 plasma chemical reactions and 32 different species are taken into account. The spatial density distributions of dominant charged ions and reactive radical species, such as ＋ ＋ ＋ ＋ CH4, CH3,N2,02, H, O, CH3, and CH2, are presented, which is due to plasma chemical reactions of methane/air dissociation （or ionization） and reforming of small fragment radical species. The physicochemical mechanisms of methane dissociation and radical species recombination are also discussed and analyzed.

Hemostasis Efficacy and Mechanism of Cold Atmospheric Air Plasma

The capacity of a cold atmospheric-pressure air plasma (CAAP) device for advanced first aid is presented. Using swine as an animal model, two trials: 1) a large, curved cut in hindquarters area and 2) amputation of a front leg, were performed. Cold atmospheric-pressure air plasma effluent, which carries reactive oxygen species (ROS) atomic oxygen (OI), is applied for wound treatments. Swift hemostasis of the wounds by the CAAP treatment was demonstrated. The pressure applied by a finger on the cut arteries in trial 1 and the tourniquet applied in trial 2 could be removed immediately after the treatment and there was no re-bleed in both cases. CAAP hemostasis mechanism was explored via in-vitro tests. The tests on sodium citrate mixed blood-droplet samples show that 1) the heat delivered by the CAAP has no impact on the observed clot formation, 2) plasma effluent activates platelets to promote coagulation state and cascade, and 3) the degree of clotting increases with the total amount of applied OI by means of the CAAP effluent. It took only 16 s of the CAAP treatment to reach full clotting, which was considerably shortened from the natural clotting time of about 25 minutes. The tests on smeared blood samples show that the reduction of the platelet count and the increase of RBC count are proportional to the amount of applied OI. A plausible CAAP hemostasis mechanism is concluded from the in vitro test results and the animal model trials.

Air Plasma Mitigation of Shock Wave

Shock wave is a detriment in the development of supersonic aircrafts;it increases flow drag as well as surface heating from additional friction;it also initiates sonic boom on the ground which precludes supersonic jetliner to fly overland. A shock wave mitigation technique is demonstrated by experiments conducted in a Mach 2.5 wind tunnel. Non-thermal air plasma generated symmetrically in front of a wind tunnel model and upstream of the shock, by on-board 60 Hz periodic electric arc discharge, works as a plasma deflector, it deflects incoming flow to transform the shock from a well-defined attached shock into a highly curved shock structure. In a sequence with increasing discharge intensity, the transformed curve shock increases shock angle and moves upstream to become detached with increasing standoff distance from the model. It becomes diffusive and disappears near the peak of the discharge. The flow deflection increases the equivalent cone angle of the model, which in essence, reduces the equivalent Mach number of the incoming flow, manifesting the reduction of the shock wave drag on the cone. When this equivalent cone angle exceeds a critical angle, the shock becomes detached and fades away. This shock wave mitigation technique helps drag reduction as well as eliminates sonic boom.

Improved Ethanol Production from Xylose by Candida shehatae Induced by Dielectric Barrier Discharge Air Plasma

Xylose fermentation is essential for ethanol production from lignocellulosic biomass. Exposure of the xylose-fermenting yeast Candida shehatae （C. shehatae） CICC1766 to atmospheric pressure dielectric barrier discharge （DBD） air plasma yields a clone （designated as C81015） with stability, which exhibits a higher ethanol fermentation rate from xylose, giving a maximal enhancement in ethanol production of 36.2% compared to the control （untreated）. However, the biomass production of C81015 is lower than that of the control. Analysis of the NADH （nicotinamide adenine dinucleotide）- and NADPH （nicotinamide adenine dinucleotide phosphate）- linked xylose reductases and NAD＋-linked xylitol dehydrogenase indicates that their activities are enhanced by 34.1%, 61.5% and 66.3%, respectively, suggesting that the activities of these three enzymes are responsible for improving ethanol fermentation in C81015 with xylose as a substrate. The results of this study show that DBD air plasma could serve as a novel and effective means of generating microbial strains that can better use xylose for ethanol fermentation.

Determination of the temporal structure of femtosecond laser pulses by means of laser-induced air plasma

A new approach is presented to reveal the temporal structure of femtosecond laser pulses by recording the correspond- ing time-resolved shadowgraphs of the laser-induced air plasma. It is shown that the temporal structures of femtosecond laser pulses, normally not observable by the ordinary intensity autocorrelator, can be detected through intuitively analyz- ing the ultrafast evolution process of the air plasma induced by the femtosecond laser pulses under examination. With this method, existence of pre- and post-pulses has been clearly unveiled within the time window of 4-150 fs in reference with the main 50-fs laser pulses output from a commercial 1-kHz femtosecond laser amplifier. The unique advantage of the proposed method is that it can directly provide valuable information about the pulse temporal structures＇ effect on the laser-induced ionization or material ablation.

The dependence on optical energy of terahertz emission from air plasma induced by two-color femtosecond laser-pulses

The generation of terahertz （THz） emission from air plasma induced by two-color femtosecond laser pulses is studied on the basis of a transient photocurrent model. While the gas is ionized by the two-color femtosecond laser-pulses com- posed of the fundamental and its second harmonic, a non-vanishing directional photoelectron current emerges, radiating a THz electromagnetic pulse. The gas ionization processes at three different laser-pulse energies are simulated, and the corresponding THz waveforms and spectra are plotted. The results demonstrate that, by keeping the laser-pulse width and the relative phase between two pulses invariant when the laser energy is at a moderate value, the emitted THz fields are significantly enhanced with a near-linear dependence on the optical energy.

Control of multidrug-resistant planktonic Acinetobacter baumannii:biocidal efficacy study by atmospheric-pressure air plasma

In this research,an atmospheric-pressure air plasma is used to inactivate the multidrug-resistant Acinetobacter baumannii in liquid.The efficacy of the air plasma on bacterial deactivation and the cytobiological variations after the plasma treatment are investigated.According to colony forming units,nearly all the bacteria（6-log） are inactivated after 10 min of air plasma treatment.However,7% of the bacteria enter a viable but non-culturable state detected by the resazurin based assay during the same period of plasma exposure.Meanwhile,86% of the bacteria lose their membrane integrity in the light of SYTO 9/PI staining assay.The morphological changes in the cells are examined by scanning electron microscopy and bacteria with morphological changes are rare after plasma exposure in the liquid.The concentrations of the long-living RS,such as H2O2,NO3^- and O3,in liquid induced by plasma treatment are measured,and they increase with plasma treatment time.The changes of the intracellular ROS may be related to cell death,which may be attributed to oxidative stress and other damage effects induced by RS plasma generated in liquid.The rapid and effective bacteria inactivation may stem from the RS in the liquid generated by plasma and air plasmas may become a valuable therapy in the treatment of infected wounds.

The mechanism study of low-pressure air plasma cleaning on large-aperture optical surface unraveled by experiment and reactive molecular dynamics simulation

Low-pressure air plasma cleaning is an effective method for removing organic contaminants on large-aperture optical components in situ in the inertial confinement fusion facility.Chemical reactions play a significant role in plasma cleaning,which is a complex process involving abundant bond cleavage and species generation.In this work,experiments and reactive molecular dynamics simulations were carried out to unravel the reaction mechanism between the benchmark organic contaminants of dibutyl phthalate and air plasma.The optical emission spectroscopy was used to study the overall evolution behaviors of excited molecular species and radical signals from air plasma as a reference to simulations.Detailed reaction pathways were revealed and characterized,and specific intermediate radicals and products were analyzed during experiments and simulation.The reactive species in the air plasma,such as O,HO_(2)and O_(3)radicals,played a crucial role in cleaving organic molecular structures.Together,our findings provide an atomic-level understanding of complex reaction processes of low-pressure air plasma cleaning mechanisms and are essential for its application in industrial plasma cleaning.