Electrochemical Hydrogen Charging on Corrosion Behavior of Ti-6Al-4V Alloy in Artificial Seawater

This study employs advanced electrochemical and surface characterization techniques to investigate the impact of electrochemical hydrogen charging on the corrosion behavior and surface film of the Ti-6Al-4V alloy.The findings revealed the formation ofγ-TiH andδ-TiH_(2) hydrides in the alloy after hydrogen charging.Prolonging hydrogen charging resulted in more significant degradation of the alloy microstructure,leading to deteriorated protectiveness of the surface film.This trend was further confirmed by the electrochemical measurements,which showed that the corrosion resistance of the alloy progressively worsened as the hydrogen charging time was increased.Consequently,this work provides valuable insights into the mechanisms underlying the corrosion of Ti-6Al-4V alloy under hydrogen charging conditions.

Dependence of microstructure and mechanical properties on solidification condition of directionally solidified Zn-55Al-1.6Si alloys

In this study,directional solidification was utilized to explore the relationship between microstructure,mechanical properties,and withdrawal speeds of Zn-55Al-1.6Si alloys.In order to assess the characteristics of Zn-55Al-1.6Si alloys,both the microstructure and mechanical properties were thoroughly analyzed.This involved conducting room temperature tensile tests on samples with different withdrawal speeds(5,10,100,200,and 400μm·s^(-1)).The results reveal that both the as-cast alloy and samples after directional solidification are composed of zinc,aluminum,and silicon phases.As the withdrawal speed increases,an evident decrease in the size of the primary dendrites is observed.The results of tensile experiments show that Zn-55Al-1.6Si alloys after directional solidification exhibit brittle fracture characteristics,both the tensile strength and elongation of the alloys increase with withdrawal speed.

Two-stage dynamic recrystallization and texture evolution in Al-7Mg alloy during hot torsion

Hot torsion tests were performed on the Al-7Mg alloy at the temperature ranging from 300 to 500℃ and strain rates between 0.05 and 5 s^(-1) to explore the progressive dynamic recrystallization(DRX)and texture behaviors.The DRX behavior of the alloy manifested two distinct stages:Stage 1 at strain of≤2 and Stage 2 at strains of≥2.In Stage 1,there was a slight increase in the DRXed grain fraction(X_(DRX))with predominance of discontinuous DRX(DDRX),followed by a modest change in X_(DRX) until the transition to Stage 2.Stage 2 was marked by an accelerated rate of DRX,culminating in a substantial final X_(DRX) of~0.9.Electron backscattered diffraction(EBSD)analysis on a sample in Stage 2 revealed that continuous DRX(CDRX)predominantly occurred within the(121)[001]grains,whereas the(111)[110]grains underwent a geometric DRX(GDRX)evolution without a noticeable sub-grain structure.Furthermore,a modified Avrami’s DRX kinetics model was utilized to predict the microstructural refinement in the Al-7Mg alloy during the DRX evolution.Although this kinetics model did not accurately capture the DDRX behavior in Stage 1,it effectively simulated the DRX rate in Stage 2.The texture index was employed to assess the evolution of the texture isotropy during hot-torsion test,demonstrating significant improvement(>75%)in texture randomness before the commencement of Stage 2.This initial texture evolution is attributed to the rotation of parent grains and the substructure evolution,rather than to an increase in X_(DRX).

Corrosion and antimicrobial property of TiO_(2)/Cu_(2)O and TiO_(2)/Cu_(2)O@CeO_(2)micro-arc oxidation coatings on Ti-6Al-4V alloys in natural seawater

Microarc oxidation is an effective surface treatment for improving certain properties of metals and their alloys.In this paper,TiO_(2)/Cu_(2)O and TiO_(2)/Cu_(2)O@CeO_(2)coatings were prepared on Ti-6Al-4V by microarc oxidation.Thecoatings exhibited good corrosion resistance and antimicrobial properties.X-ray diffraction(XRD),scanning electronmicroscopy(SEM),and 3D laser confocal were used to characterize the coatings.The properties of TiO_(2)/Cu_(2)O and TiO_(2)/Cu_(2)O@CeO_(2)coatings were analyzed,including microstructure,surface roughness,corrosion resistance,andantimicrobial properties.The electrochemical results showed that the coatings prepared by microarc oxidation hadenhanced corrosion resistance compared to the substrate.The antibacterial properties of TiO_(2)/Cu_(2)O and TiO_(2)/Cu_(2)O@CeO_(2)coating against Pseudomonas aeruginosa were evaluated by fluorescence microscopy and plate counting.The antibacterial rate of TiO_(2)/Cu_(2)O@CeO_(2)coating was up to 99.70%.In summary,the TiO_(2)/Cu_(2)O and TiO_(2)/Cu_(2)O@CeO_(2)coatings prepared by microarc oxidation have a potential application background in the field of marine corrosionprotection and biofouling.

Effects of neodymium addition on microstructure and mechanical properties of near-eutectic Al-12Si alloys

The microstructure and mechanical properties of near-eutectic Al-12 Si alloys modified with 0-0.4% Nd（mass fraction） were investigated. The results indicate that a submicro- or nano-sized Al2 Nd phase is observed in the modified alloy with 0.3% Nd. The morphology of the α（Al） phase is significantly refined in the Nd-modified alloys. The primary Si morphology simultaneously changes into a fine, particle-like morphology, and the morphology of eutectic Si becomes fine-fibrous instead of coarse-acicular. Relatively few growth twins are observed on the surface of the Si plate in the Al-12Si-0.3Nd alloy at the optimal modification level. The mechanical property test results confirm that the mechanical properties of the as-cast Al-12 Si alloys are enhanced after the Nd addition, with optimal ultimate tensile strength（UTS） of 252 MPa and elongation（EL） of 13% at an Nd content of 0.3%. The improved mechanical properties are attributed to the refined morphology of Si phase and the formation of the Al2 Nd phase.

Corrosion mechanism associated with Mg_2Si and Si particles in Al-Mg-Si alloys

The electrochemical behaviors and coupling behaviors of the Mg2Si and Si phases with α（Al） were investigated, the corrosion morphologies of Al alloys containing Mg2Si and Si particles were observed, and the corrosion mechanism associated with them in Al-Mg-Si alloys was advanced. The results show that Si particle is always cathodic to the alloy base, Mg2Si is anodic to the alloy base and corrosion occurs on its surface at the beginning. However, during its corrosion process, the preferential dissolution of Mg and the enrichment of Si make Mg2Si transform to cathode from anode, leading to the anodic dissolution and corrosion of the alloy base at its adjacent periphery at a later stage. As the mole ratio of Mg to Si in an Al-Mg-Si alloy is less than 1.73, it contains Mg2Si and Si particles simultaneously in the grain boundary area, and corrosion initiates on the Mg2Si surface and the precipitate-free zone （PFZ） at the adjacent periphery of Si particle. As corrosion time is extended, Si particle leads to severe anodic dissolution and corrosion of the PFZ at its adjacent periphery, expedites the polarity transformation between Mg2Si and the PFZ and accelerates the corrosion of PFZ at the adjacent periphery of Mg2Si particle.

Grain refining mechanism of Al-3B master alloy on hypoeutectic Al-Si alloys

Al-3B master alloy is a kind of efficient grain refiner for hypoeutectic Al-Si alloys. Experiments were carried out to evaluate the effect of undissolved AlB2 particles in Al-3B master alloy on the grain refinement of Al-7Si. It is found that the number and the settlement of AlB2 particles in the melt all have effect on the grain refining efficiency. On the basis of experiments and theoretical analysis, a new grain refinement mechanism was proposed to explain the grain refinement action of Al-3B on hypoeutectic Al-Si alloys. The formation of ＇Al-AlB2＇ shell structure is the direct reason for grain refinement and the undissolved AlB2 particles is the indirect nucleating base for subsequent α（Al） phase.

不同固溶处理对亚共晶Al-Si合金组织和性能的影响

铸态的亚共晶Al-Si合金中,粗大的α-Al晶粒和针片状共晶Si是造成其性能降低的主要原因。通过对Al-Ti-La和Nd细化变质后的Al-7Si合金进行了不同条件的固溶处理,研究了不同固溶温度和时间对其微观组织及性能的影响。结果表明:铸态Al-7Si合金随着固溶温度的升高,二次枝晶臂间距(SDAS)逐渐增大,共晶Si尺寸逐渐减小,并且共晶Si由长条状和纤维状向短棒状转变。随着固溶时间的延长,共晶Si的演变过程为:长条状→短棒状→粒状→粗化长大。当固溶温度为535℃、固溶时间为3 h时,合金的显微硬度为62.5 HV,相比于铸态提升了10.5%,极限抗拉强度(UTS)和断裂延伸率(El)由铸态的170.2 MPa和11.1%提升至174.0 MPa和13.1%,分别提升2.2%和18.0%,断口的解理平台小且出现大面积韧窝,由脆性断裂转变为韧性断裂。

Effects of Mn and Sn on microstructure of Al-7Si-Mg alloy modified by Sr and Al-5Ti-B

The effects of Mn and Sn on the microstructure of Al?7Si?Mg alloy modified by Sr and Al?5Ti?B were studied. The results show that the columnar dendrites structure is observed with high content of Sr, indicating a poisoning effect of the Al?5Ti?B grain refinement. In addition, Sr intermetallic compounds distribute on the TiB2 particles, which agglomerate inside the eutectic Si. The mechanism responsible for such poisoning was discussed. The addition of Mn changes the morphology of iron intermetallic compounds fromβ-Al5FeSi toα-Al(Mn,Fe)Si. Increasing the amount of Mn changes the morphology ofα-Al(Mn,Fe)Si from branched shape to rod-like shape with branched distribution, and finally convertsα-Al(Mn,Fe)Si to Chinese script shape. The microstructure observed by transmission electron microscopy (TEM) shows that Mg is more likely to interact with Sn in contrast with Si under the effect of Sn. Mg2Sn compound preferentially precipitates between the Si/Si interfaces and Al/Si interfaces.

Effect of electropulsing on deformation behavior of Ti-6Al-4V alloy during cold drawing

Electron backscattered diffraction （EBSD） and transmission electron microscopy （TEM） were used to investigate effect of electropulsing on microstructure and texture evolution of Ti-6Al-4V during cold drawing. Research results demonstrate that the electropulsing treatment （EPT） can enhance the deformability of the grains with unfavorable orientations, which makes the compatibility of deformation among grains much better. A comparison in texture evolution between conventional cold drawing and EPT cold drawing indicates that the EPT promotes prismatic 〈a〉 slip moving, restricts pyramidal 〈c＋a〉 slip occurring and accommodates the deformation with c-component by grain boundary sliding. The fraction decrease of low-angle grain boundaries for samples deformed with EPT reveals that the application of electropulsing restricts the formation of the incidental dislocation boundaries and the geometrically necessary boundaries.

Tribocorrosion behaviors of Ti-6Al-4V and Monel K500 alloys sliding against 316 stainless steel in artificial seawater

The tribocorrosion behaviors of Ti-6Al-4V and Monel K500 alloys sliding against 316 stainless steel were investigated using a ring-on-block test rig in both artificial seawater and distilled water. It is found that friction coefficients are in general larger in distilled water compared with seawater. The wear losses of Ti-6Al-4V and Monel K500 alloys are larger in seawater compared with distilled water. The mechanical action can destroy the passive film and increase the corrosion rate. The synergism effect between corrosion and wear occurs. The synergism action between corrosion and wear is related to the corrosion rate and with the increase of corrosion rate, the synergism becomes more important. 316 stainless steel suffers severe wear sliding against Monel K500 alloy compared with sliding against Ti-6Al-4V alloy in both distilled water and seawater.

Hot deformation behavior of Al-9.0Mg-0.5Mn-0.1Ti alloy based on processing maps

Hot deformation behavior of extrusion preform of the spray-formed Al-9.0Mg-0.5Mn-0.1Ti alloy was studied using hot compression tests over deformation temperature range of 300-450 ℃ and strain rate range of 0.01-10 s-1. On the basis of experiments and dynamic material model, 2D processing maps and 3D power dissipation maps were developed for identification of exact instability regions and optimization of hot processing parameters. The experimental results indicated that the efficiency factor of energy dissipate （η） lowered to the minimum value when the deformation conditions located at the strain of 0.4, temperature of 300 ° C and strain rate of 1 s-1. The softening mechanism was dynamic recovery, the grain shape was mainly flat, and the portion of high angle grain boundary （〉15°） was 34%. While increasing the deformation temperature to 400 ° C and decreasing the strain rate to 0.1 s-1, a maximum value of η was obtained. It can be found that the main softening mechanism was dynamic recrystallization, the structures were completely recrystallized, and the portion of high angle grain boundary accounted for 86.5%. According to 2D processing maps and 3D power dissipation maps, the optimum processing conditions for the extrusion preform of the spray-formed Al？9.0Mg？0.5Mn？0.1Ti alloy were in the deformation temperature range of 340-450 ° C and the strain rate range of 0.01-0.1 s-1 with the power dissipation efficiency range of 38%？43%.

Microstructures and properties of Al-45%Si alloy prepared by liquid-solid separation process and spray deposition

The microstructures and properties of A1-45%Si alloy prepared by liquid-solid separation （LSS） process and spray deposition （SD） were studied. The results show that the size, shape and distribution of the primary Si phase have different influence on the properties of alloys. Comparing with the Si particles with irregular shape, fine size and continuous distribution in SD alloy, the primary Si phase in LSS alloy is sphere-like, coarse and surrounded by the continuous AI matrix. The microstructure features of LSS alloy are beneficial to the higher thermal conductivity and lower thermal expansion coefficient at room temperature. The fine Si particle in SD alloy is advantageous to improving the mechanical properties. The increasing rates of thermal expansion coefficient with temperature are influenced by the distribution of the Si particles, where a lower rate is obtained in SD alloy with continuous Si particles. The agreement of thermal expansion coefficient with the model in LSS alloy differs from that in the SD alloy because of the different microstructure characteristics.

Effects of Al-Ti-B-RE grain refiner on microstructure and mechanical properties of Al-7.0Si-0.55Mg alloy

To investigate the effects of Al-Ti-B-RE grain refiner on microstructure and mechanical properties of Al-7.0Si-0.55Mg （A357） alloy, some novel Al-7.0Si-0.55Mg alloys added with different amount of Al-STi-1B-RE grain refiner with different RE composition were prepared by vacuum-melting. The microstructure and fracture behavior of the AI-7.0Si-0.55Mg alloys with the grain refiners were observed by X-ray diffraction （XRD）, optical microscopy （OM）, scanning electron microscopy （SEM）, and the mechanical properties of the alloys were tested in mechanical testing machine at room temperature. The observation of AI-Ti-B-RE morphology and internal structure of the particles reveals that it exhibits a TiAl3/Ti2Al20RE core-shell structure via heterogeneous TiB2 nuclei. The tensile strength of Al-7.0Si-0.55Mg alloys with Al-5Ti-1B-3.0RE grain refiner reaches the peak value at the same addition （0.2%） of grain refiner.

Influence of hydrogen content on room temperature compressive properties of Ti-6Al-4V alloy at high strain rate

Electromagnetic forming tests were done at room temperature to reveal the influence of hydrogen content on the compressive properties of Ti-6Al-4V alloy at high strain rate. Microstructure was observed to reveal the mechanism of hydrogen-enhanced compressive properties. The experimental results indicate that hydrogen has favorable effects on the compressive properties of Ti-6Al-4V alloy at high strain rate. Compression of Ti-6Al-4V alloy first increases up to a maximum and then decreases with the increase of hydrogen content at the same discharge energy under EMF tests. The compression increases by 47.0% when 0.2% (mass fraction) hydrogen is introduced into Ti-6Al-4V alloy. The optimal hydrogen content for cold formation of Ti–6Al–4V alloy under EMF was determined. The reasons for the hydrogen-induced compressive properties were discussed.

表面喷丸及退火处理对Fe-30Mn-3Al-3Si TWIP钢组织与性能的影响

为实现强韧化,对Fe-30Mn-3Al-3Si TWIP钢进行了表面喷丸及退火热处理。采用金相显微镜、X射线衍射仪和透射电子显微镜等手段分析了喷丸以及喷丸结合退火处理对TWIP钢显微组织结构的影响,并利用显微维氏硬度计和万能材料试验机对原始样品、喷丸以及喷丸结合退火处理样品的硬度分布、力学性能及加工硬化行为进行了研究。分析结果表明,喷丸可在TWIP钢表面引起强烈的塑性变形,并形成包含60~100 nm大小的位错胞块的强烈形变层和包含微纳尺度形变孪晶结构的过渡层。该纳米-微米尺度的晶粒尺寸梯度结构可以将TWIP钢表面强烈形变层的硬度显著提升至366 HV0.1,并在残余压应力联合作用下使试样的屈服强度提升至485 MPa,均远高于初始样品的对应值。但受喷丸引起的表面粗糙和强烈形变层纳米晶塑性低的影响,其断后延伸率仅为41.8%。退火处理后,喷丸样品中的形变组织发生回复与再结晶,其中强烈形变层位置的再结晶晶粒尺寸为1~3μm,硬度也降低至215 HV0.1。所形成的微米-微米尺度晶粒尺寸梯度结构试样的屈服强度降低至261 MPa,但延伸率增加至65.3%。晶粒尺寸梯度结构有助于增加TWIP钢屈服与抗拉强度,但不利于延伸率的提升。

Sr含量对Al-Si合金显微组织和热导率的影响

以纯铝、Al-20Si和Al-10Sr中间合金为原料,Sr为变质剂(含量为0.01%、0.02%、0.04%和0.06%,质量分数),制备了Al-7Si-xSr、Al-12Si-xSr和Al-20Si-xSr合金,研究了Sr含量对Al-Si合金相变储热材料显微组织及热导率的影响。利用Hot Disk热常数分析仪测量合金的热导率,通过扫描电镜观察及分析合金的显微组织。结果表明:在Al-Si合金中添加变质元素Sr会影响合金的热导率,Al-7Si-0.04Sr合金热导率较Al-7Si合金增加了73.47 W·m^(-1)·K^(-1),Al-20Si-0.04Sr合金的热导率较Al-20Si合金增加了24.09 W·m^(-1)·K^(-1),Al-12Si-0.04Sr合金的热导率较Al-12Si合金增加了17.79 W·m^(-1)·K^(-1)。铝硅合金热导率的增长主要与α(Al)、共晶硅和初晶硅的形貌有关。经过Sr变质之后,Al-7Si合金中共晶Si立体形貌均由片层状转变为珊瑚状,Al-12Si和Al-20Si合金中共晶Si立体形貌由片层状转变为枝条状;其中,Al-7Si合金中α(Al)尺寸明显减少、排列紧密,二次枝晶臂间距逐渐减小;Al-20Si合金中的初晶Si尺寸明显减小,其形貌由多角的大块状变为小块状;α(Al)形态的转变不仅能够为自由电子的传输提供快速通道,而且还会使得共晶Si的排列更加规则,减少自由电子发生散射的几率,对合金的热导率影响较大。共晶Si由片层状转变为珊瑚状或枝条状,增加电子的平均自由程,有利于电子的传输。Al-20Si合金的热导率与初晶Si的形态有着重要联系,大尺寸且形状完整的初晶Si会发生晶格振动,会提高合金的热导率。

In situ study on columnar-equiaxed transition and anaxial columnar dendrite growth of Al-15%Cu alloy by synchrotron radiography

Directional solidification of Al-15% （mass fraction） Cu alloy was investigated by in situ and real time radiography which was performed by Shanghai synchrotron radiation facility （SSRF）. The imaging results reveal that columnar to equiaxed transition （CET） is provoked by external thermal disturbance. The detaching and floating of fragments of dendrite arms are the prelude of the transition when the solute boundary layer in front of the solid-liquid interface is thin. And the dendrite triangular tip is the fracture sensitive zone. When the conditions are suitable, new dendrites can sprout and grow up. This kind of dendrite has no obvious stem and is named anaxial columnar dendrites.

Effects of isothermal process parameters on semisolid microstructure of Mg-8%Al-1%Si alloy

A Mg-8%Al-1%Si alloy with semisolid microstructure was fabricated by isothermal heat treatment process. The effects of isothermal process parameters such as holding temperature and holding time on the microstructure of Mg-8%Al-1%Si alloy were investigated. The results show that a non-dendritic microstructure could be obtained by isothermal heat treatment. With increasing holding temperature from 560 to 575 °C or holding time from 5 to 30 min, the liquid volume fraction increases, the average size of α-Mg grains grows larger and globular tendency becomes more obvious. In addition, the Mg2Si phase transforms from Chinese script shape to granule shape. The morphology modification mechanisium of Mg2Si phase in Mg-8%Al-1%Si alloy during the semisolid isothermal heat treatment was also studied.

Effect of grain size of primary α phase on bonding interface characteristic and mechanical property of press bonded Ti-6Al-4V alloy

The effect of grain size of primary α phase on the bonding interface characteristic and shear strength of bond was investigated in the press bonding of Ti-6Al-4V alloy. The quantitative results show that the average size of voids increases from 0.8 to 2.6 μm and the bonding ratio decreases from 90.9% to 77.8% with an increase in grain size of primary α phase from 8.2 to 16.4 μm. The shape of voids changes from the tiny round to the irregular strip. The highest shear strength of bond can be obtained in the Ti-6Al-4V alloy with a grain size of 8.2 μm. This is contributed to the higher ability of plastic flow and more short-paths for diffusion in the alloy with smaller grain size of primary α phase, which promote the void closure process and the formation of α/β grains across bonding interface.