Preparation of Laser Cladding Coating Undercooling Cu-based Alloy and Co on Non-equilibrium Solidification Structure

The effect of the gradient content of Co element on the solidification process of Cu-based alloy under deep under cooling conditions was explored.The non-equilibrium solidification structure of the under cooled alloy samples were analyzed.It is found that the rapidly solidified alloy has undergone twice grain refinement during the undercooling process.Characterization and significance of the maximum undercooling refinement structure of Cu60Ni35Co5 at T=253 K were analyzed.High-density defects were observed,such as dislocations,stacking faults networks,and twinning structures.The standard FCC diffraction pattern represents that it is still a single-phase structure.Based on the metallographic diagram,EBSD and TEM data analysis,it is illustrated that the occurrence of grain refinement under high undercooling is due to stress induced recrystallization.In addition,the laser cladding technology is used to coat Co-based alloy(Stellite12) coating on 304 stainless steel substrate;the microstructure of the coating cross-section was analyzed.It was found that the microstructure of the cross-section is presented as columnar crystals,planar crystals,and disordered growth direction,so that the coating has better hardness and wear resistance.By electrochemical corrosion of the substrate and coating,it can be seen that the Co and Cr elements present in the coating are more likely to form a dense passivation film,which improved the corrosion resistance of the coating.

Simulation of microstructures in solidification of aluminum twin-roll casting

Based on the research on the solidification of twin-roll continuous casting aluminum thin strip, the analytical model of heterogeneous nucleation, the growth kinetics of tip （KGT） and columnar dendrite transformation to equiaxed dendrite （CET） of twin-roll continuous casting aluminum thin strip solidification was established by means of the principle of metal solidification and modem computer emulational technology. Meantime, based on the cellular automaton, the emulational model of twin-roll continuous casting aluminum thin strip, solidification was established. The foundation for the emulational simulation of twin-roll casting thin strip solidification structure was laid. Meanwhile, the mathematical simulation feasibility was confirmed by using the solidification process of twin-roll continuous casting aluminum thin strip.

Banding structure formation during directional solidification of Pb-Bi peritectic alloys

Directional solidification experiments on Pb-Bi peritectic alloys were carried out at very low growth rate （v=0.5 μm/s） and high temperature gradient （G=35 K/mm） in an improved Bridgman furnace. The banding structures were observed in both hypoperitectic and hyperperitectic compositions （Pb-xBi, x=26%, 28%, 30% and 34%）. Tree-like primary α phase in the center of the sample surrounded by the peritectic β phase matrix was also observed, resulting from the melt convection. The banding microstructure, however, is found to be transient after the tree-like structure and only the peritectic phase forms after a few bands. Composition variations in the banding structure are measured to determine the nucleation undercooling for both α and β phases. In a finite length sample, convection is shown to lead only to the transient formation of bands. In this transient banding regime, only a few bands with a variable width are formed, and this transient banding process can occur over a wide range of compositions inside the two-phase peritectic region.

Structure Evolution and Solidification Behavior of Austenitic Stainless Steel in Pulsed Magnetic Field

To understand the solidification behavior of austenitic stainless steel in pulsed magnetic field, the solidification process is investigated by means of the self-made high voltage pulse power source and the solidification tester. The results show that the solidification structure of austenitic stainless steel can be remarkably refined in pulsed magnetic field, yet the grains become coarse again when the magnetic intensity is exceedingly large, indicating that an optimal intensity range existed for structure refinement. The solidification temperature can be enhanced with an increase in the magnetic intensity. The solidification time is shortened obviously, but the shortening degree is reduced with the increase of the magnetic intensity.

Solidification Structure of Low Carbon Steel Strips with Different Phosphorus Contents Produced by Strip Casting

In the present paper, low carbon steel strips with different phosphorus contents were produced using a twin roll strip casting process. The solidification structure was studied and its features were analyzed in detail. It was found that the strips possessed a fine microstructure compared with the mould cast steels. With increasing phosphorus content more ferrite has been formed with finer grains.

Effect of electric pulse treatment on solidification structure of an Al-15%Si alloy

The effect of electric pulse modifying on the solidification structure of an Al-15%Si alloy was investigated. The result shows that the primary silicon disappears sometimes and the eutectic phase is refined after the treatrnent of EP （electric pulse） though there are different modalities in different treating durations. DSC （differential scanning calorimetry） analysis indicates that the super-cooling texture decreases and the freezing range narrows evidently after the electric pulse treatment.

Effect of Rectangle Wave Pulse Current on Solidification Structure of ZA27 Alloy

The effect of rectangle wave pulse current on solidification structure of ZA27 alloy was studied. The restdts show that the wave pattern relies on the frequency range of harmonic wave and the energy of pulse current within the frequency range of pulse current. Imposed pulse current could induce the solidification system to oscillate. The frequency range and the relevant energy distribution of pulse current exert an influence on the amount of atoms involved for forming critical nucleus, the surface states of dusters in melt, the oscillating state of melt on the surface of dusters, the active energy of atom diffusion , the frequnce response of the resonance of bulk melt and the absorbability of the solidification system to the external work. Rectangle wave pulse current involves rich harmonic waves ; the amplitudes of high order of harmonic waves are higher and reduce slowly, so it has a better effect on inoculation and modification.

Effect of ultrasonic power and casting speed on solidification structure of 7050 aluminum alloy ingot in ultrasonic field

With the experiment and finite element simulation, the influences of power ultrasonic on the solidification structure of 7050 aluminum alloy ingot in semi-continuous casting were researched, and the effects of casting speed on solidification structure in ultrasonic field were also analyzed. The experiment and simulation results show that the solidification structure of the ingot is homogeneously distributed, and its grain size is obviously refined at ultrasonic power of 240 W. The average grain sizes, which can be seen from the Leica microscope, are less than 100 μm. When the casting speed is 45-50 mm/min, the best grain refinement is obtained.

Effect of pulse magnetic field on solidification structure and properties of pure copper

The application of pulse magnetic field to metal solidification is an advanced technique which can remarkably refine solidification structure. In this paper, the effect of pulse magnetic field on solidification structure, mechanical properties and conductivity of pure copper was experimentally investigated. The results showed that the solidification structure transformed from coarse columnar crystal to fine globular crystal with increasing pulse voltage. Increasing pulse voltage also improved the tensile strength. However, with the increase of pulse voltage, the elongation and electrical resistivity firstly decreased, then increased when the pulse voltage beyond a critical value. Moreover, in some conditions, pulse magnetic field can simultaneously improve the conductivity and mechanical property of pure copper.

Electro-Pulse on Improving Steel Ingot Solidification Structure

Pulse Electric Discharging (PED) is a novel technique that can modify solidifying structure and reduce grain size. ItS effectsapplied to the high carbon liquid steel were presented here. The macrostructure and microstructure of the high carbon alloy steel werealso observed. Results show that (1 ) the length of columnar crystal at the edge of ingot without PED treatment is much longer than thatwith PED, and (2) the perlite lamellae of steel billets after deposed by PED are twisted and shortened. An explanation of those experimental results is given.

Simulation on solidification structure of 72A tire cord steel billet using CAFE method

The solidification microstructure has an important effect on the mechanical properties of castings. Therefore, an FE （Finite Element） - CA （Cellular Automaton） coupling model was developed for the simulation of solidification structure during the continuous casting process of 72A tire cord steel. In the model, the effect of phase transformation （λ→γ→α） during solidification was considered based on a thermodynamic database. The effect of electromagnetic stirring （EMS） was determined by increasing both the thermal conductivity and crystal formation rate in the liquid phase. The results show that the cooling curves and solidification structure calculated by this model agree well with the experimental results. The optimum pouring temperature range for tire cord steel casting was also discussed based on the present model. By comprehensive consideration of billet quality and smooth production, the pouring temperature should be controlled at about 1,495 ℃ under the casting conditions of the local plant in this study.

Effect of temperature field on solidification structure of pure Al under pulse magneto-oscillation

This article discusses the effect of temperature field on the Pulse Magneto-Oscillation(PMO) induced solidification refinement of pure aluminium to provide more information for the industrial application of the PMO solidification technology.The temperature field is altered mainly by applied variable cooling conditions and pulse parameters.Experimental results show that the refinement effect in the case of full sand mould applied is weakened with the decreasing of cooling rate,however,in the alternative case,the sand mould whose sand bottom was replaced by a graphite block is favorable to the survival of equiaxed nucleus.The refinement mechanism is discussed in terms of the relationship between temperature field and the formation process of solidified structure.The formation or survival of nucleus depends on both temperature field and Joule heat produced by PMO,both low pulse frequency and high pulse current were experimentally confirmed to be effective;and PMO was demonstrated high potential in industrial application.

Effect of cooling rate on solidification structure and linear contraction of a duplex stainless steel

Cooling rate is a key factor that can drastically affect the phase transformation and thermal stress of duplex stainless steels. Therefore, in this research, different sand moulds were used to explore the influence of cooling rate on the solidification of the 2304 duplex stainless steel (DSS). The macro and micro structures of the 2304 DSS were investigated. Small equiaxed grains are obtained in chromite sand mould sample with a lower pouring temperature and a higher cooling rate, whereas coarse columnar and equiaxed grains are found in silica sand and refractory powder mould samples. The size of austenite phase is significantly increased with decreasing cooling rate, while the ferrite phase content ranging from 51.6% to 53.9% does not change obviously. In addition, the linear contraction of the 2304 DSS decreases from 2.34% to 1.09% when the mean cooling rate above 1,173 K increases from 0.99 K·s-1 to 3.66 K·s-1.

Improving the solidification structure of commercially pure aluminium with electropulse acting on liquid metal

The effect of electropulse on the solidification structure of commercially pure aluminium was studied. The orthogonal array L9 was used to determine the effect of three process parameters of electropulse modification （EPM）, which were pulse current intensity, pulse frequency, and treating time. For each factor, three levels were chosen to cover the experimental region. According to the experimental results, the solidification structure of commercially pure aluminium was modified from large grains with columnar crystals to finer grains with equiaxed crystals, by allowing the electropulse to act on liquid aluminium. However, the solidification structures could be refined differently at different EPM parameters. Certain EPM parameters should be selected to get the optimum solidification structure. Among the three parameters, pulse frequency was the most important factor influencing the solidification structure, the secondary factor was current intensity, and treating time was the third one. The optimum parameters were the pulse frequency of 5 Hz, the current intensity of 68 A, and the treating time of l0 s.

Effect of micro-alloying Nb and Ti on solidification structure in 430 ferritic stainless steel

With the increase in the content of carbon, nitrogen and titanium in 430 ferritic stainless steel, the refinement of the solidification structure is obvious and the proportion of equiaxed grain increases remarkably as well. This is attributed to the increasing role of the inhomogeneous nucleation by TiN particles during solidification. In addition, more fine precipitations of （Ti ,Nb）N are found in steel with increased carbon and nitrogen content.

Physical Properties and Solidification Structure of Al－SiEutectic Alloy Melt with Cerium Modification

Relationship between physical property change of melt and solidification structure has been investigated by measuring the density, viscosity and electrical resistivity of the Al-Si eutectic alloy melt with different Ce contents. The results show that there exists corresponding relation between the turning points of physical properties change and eutectic Si shape change.

Effects of Pulse Current on Solidification Structure of Austenitic Stainless Steel

The 1Cr18Ni9Ti specimens were treated respectively with pulse current under 520 V and 2 600 V during solidification and the solidification structure was observed.The results showed that pulse current can refine solidification grains,cut primary dentrities remarkably and reduce second dentritic arm spacing.The mechanism and effect are changed with operation parameters.

Solidification behavior and rheo-diecasting microstructure of A356 aluminum alloy prepared by self-inoculation method

Semisolid slurry of A356 aluminum alloy was prepared by self-inoculation method, and the microstructure and solidification behavior during rheo-diecasting process were investigated. The results indicate that the semisolid slurry of A356 aluminum alloy can be prepared by self-inoculation method at 600℃. Primary a-AI particles with fine and spherical morphologies are uniformly distributed when the isothermal holding time of slurry is 3 min. Liquid phase segregation occurs during rheo-diecasting process of semisolid slurry and the primary particles （α1） show obvious plastic deformation in the area of high stress and low cooling rate. A small amount of dendrites resulting from the relatively low temperature of the shot chamber at the initial stage of secondary solidification are fragmented as they pass through the in-gate during the mould filling process. The amount of dendrite fragments decreases with the increase of filling distance. During the solidification process of the remaining liquid, the nucleation rate of secondary particles （α2） increases with the increase of cooling rate, and the content of Si in secondary particles （α2） are larger than primary particles （α1）. With the increase of cooling rate, the content of Si in secondary particles （α2） gradually increases. The morphologies of eutectic Si in different parts of die casting are noticeably different. The low cooling rate in the first filling positions leads to coarse eutectic structures, while the high cooling rate in the post filling positions promotes small and compact eutectic structures.

Effect of hafnium addition on solidification structure of cast Ti-46Al alloys

To investigate the effect of hafnium addition on the solidification structure, Ti-46AI alloys with nominal compositions of Ti-46AI-xHf （x = 0, 3, 5, 7） （at.%） were arc-melted into small ingots in an argon atmosphere. The characteristics of the macrostructures and microstructures were studied using a linear intercept method, OM, SEM （BSE）, XRD and TEM. The results showed that the ingots with Hf have near lamellar microstructure in columnar and dendrite morphology. The hafnium concentration has a strong effect on the columnar spacing refinement. Increasing Hf from 0 to 7 （at.%）, the columnar spacing can be reduced from - 1000 to-400 μm. Constitute phases of the ingots are a2, a small amount of B2 and 7. Most of the B2 phases, richer in Hf and leaner in AI and Ti, exist on the node of the dendrite core in block shape and a little across the lamellar colonies in stick shape. The 7 phases exist on the boundaries of lamellar colonies in small cellular shape. There also exists a segregation of Hf on the columnar and dendrite core. Particularly, both the a-and ,β-phase form from the melt as prior phases. The possible phase sequencing during solidification and solid-state transformations with Hf is given in this paper.

Liquid−liquid structure transition in metallic melt and its impact on solidification:A review

Understanding the nature of liquid structures and properties has always been a hot field in condensed matter physics and metallic materials science.The liquid is not homogeneous and the local structures inside change discontinuously with temperature,pressure,etc.The liquid will experience liquid−liquid structure transition under a certain condition.Liquid−liquid structure transition widely exists in many metals and alloys and plays an important role in the final microstructure and the properties of the solid alloys.This work provides a comprehensive review on this unique structure transition in the metallic liquid together with the recent progress of its impact on the following microstructure and properties after solidification.These effects are discussed by integrating them into different experimental results and theoretical considerations.The application of liquid−liquid structure transition as a strategy to tailor the properties of metals and alloys is proven to be practical and efficient.