To investigate the effect of rare earth on size and distribution of TiB2 phase in aluminum alloy refiner,Al-5Ti-1B-RE master alloy was fabricated,and its microstructure and phase constitutions were investigated by the...To investigate the effect of rare earth on size and distribution of TiB2 phase in aluminum alloy refiner,Al-5Ti-1B-RE master alloy was fabricated,and its microstructure and phase constitutions were investigated by the combination of first principles calculations and experimental investigation.The calculated results reveal that Ce has the most effective modification ability due to the most positive adsorption energy and the largest charge transfer value compared with other rare earth elements.Results of experimental investigation indicate that the addition of rare earth in the Al-5Ti-1B alloys can greatly refine the particle size of TiB2,improve the distribution of particles and lead to better refinement effect than that of the Al-5Ti-1B alloys without rare earth.Moreover,Ce has the best optimization effect,which agrees well with the calculated results.展开更多
Commercial A356 alloy was refined with a homemade A1-5Ti-0.25C-2RE master alloy, and the microstructure and macrostructure of the refined alloy were investigated. The results show that the grain refining effect of A35...Commercial A356 alloy was refined with a homemade A1-5Ti-0.25C-2RE master alloy, and the microstructure and macrostructure of the refined alloy were investigated. The results show that the grain refining effect of A356 is poor by the addition level of 0.5 wt% master alloy, but when the level reaches 3.0 wt% the grain can get a satisfactory refining effect. Dendrite of A356 can be effectively refined by addition of 0.5 wt% master alloy; however, the refining effect is not significantly improved by further increasing the addition of master alloy. Grain and dendrite refining effects are compared in this article, and the results show that the grain and dendrite exhibit different refining effects with the same addition level of master alloy. Dendrite is easier to reach the optimal refining effect than grain.展开更多
The Al-5Cu alloys were prepared by different treatment methods,including adding a refiner Al-5Ti-1B,exerting a rotating magnetic field(RMF),and compound treatment of both refiner and RMF.The effects of treatment metho...The Al-5Cu alloys were prepared by different treatment methods,including adding a refiner Al-5Ti-1B,exerting a rotating magnetic field(RMF),and compound treatment of both refiner and RMF.The effects of treatment methods on the microstructure,properties,and solid solubility of the Al-5Cu alloy were investigated.The optimal magnetic field parameters and addition amount of refiner were confirmed by experiment.Results show that either RMF or adding refiner Al-5Ti-1B alone can refine the grain size,and the refining effect can be further improved by a compound refining treatment with optimized magnetic field parameters(120 A current and 8 Hz frequency) and 1.0wt.% Al-5Ti-1B refiner(RMF*+Al-5Ti-1B*).The average grain size is decreased to 68.1 μm,which is 60.8%,21.1%,and 83.5% lower than that of the alloy treated by the optimized rotating magnetic field,the Al-5Ti-1B refiner,and the alloy without any treatment,respectively.The tensile strength and elongation of the alloy reach 232.5 MPa and 18.6%,respectively,which are obviously higher than those of the alloys treated by rotating magnetic field,Al-5Ti-1B refiner,and the alloy without any treatment,respectively.Additionally,the solid solubility of the alloy is also obviously improved compared to the alloys treated by other methods.展开更多
Power consumption is the energy source of the impact on fibers or pulp during low-consistency(LC)pulp refining,and the strength of refining affects refining quality and efficiency.The pulp properties,operating paramet...Power consumption is the energy source of the impact on fibers or pulp during low-consistency(LC)pulp refining,and the strength of refining affects refining quality and efficiency.The pulp properties,operating parameters,and bar parameters of the refiner plates are important parameters affecting refining efficiency,which can be defined as the ratio of net to total refining power.In this study,LC refining trials for pulps with different consistencies and fiber lengths were conducted using five isometric straightbar plates with different bar angles to explore the influences of the plate bar angle and pulp properties on the no-load power,impact capacity on fibers and refining efficiency.It was found that the no-load power of the LC refining process decreased with an increase in the plate bar angle while increased when pulp with higher consistency was refined under the same refining conditions.However,the effect of pulp consistency on the no-load power can be neglected when refining is conducted using plates with larger bar angles.Meanwhile,a critical bar angle for straight-bar plates in LC refining may exist,which has the strongest impact on the pulp and highest refining efficiency under the same refining conditions.In addition,the impact capacity of the plate on the pulp and refining efficiency in LC refining can be enhanced by appropriately increasing the pulp consistency and average fiber length when the bar angle of the refiner plate with a sector angle of 40°is less than 30°.Therefore,the efficiency and power consumption of the LC refining process can be adjusted by optimizing the pulp consistency and bar parameters of the refining plates.展开更多
Through the use of purification and recirculation superheating techniques on molten glass,the Ni65Cu33Co2 alloy was successfully undercooled to a maximum temperature of 292 K.High-speed photography was employed to cap...Through the use of purification and recirculation superheating techniques on molten glass,the Ni65Cu33Co2 alloy was successfully undercooled to a maximum temperature of 292 K.High-speed photography was employed to capture the process of interface migration of the alloy liquid,allowing for an analysis of the relationship between the morphological characteristics of the alloy liquid solidification front and the degree of undercooling.Additionally,the microstructure of the alloy was examined using metallographic microscopy,leading to a systematic study of the microscopic morphological characteristics and evolution laws of the refined structure during rapid solidification.The research reveals that the grain refining mechanism of the Ni-Cu-Co ternary alloy is consistent with that of the binary alloy(Ni-Cu).Specifically,under low undercooling conditions,intense dendritic remelting was found to cause grain refinement,while under high undercooling conditions,recrystallization driven by accumulated stress and plastic strain resulting from the interaction between the liquid flow and the primary dendrites caused by rapid solidification was identified as the main factor contributing to grain refinement.Furthermore,the study highlights the significant role of the Co element in influencing the solidification rate and reheat effect of the alloy.The addition of Co was also found to facilitate the formation of non-segregated solidification structure,indicating its importance in the overall solidification process.展开更多
In Mg-Ca alloys the grain refining mechanism,in particular regarding the role of nucleant substrates,remains the object of debates.Although native MgO is being recognised as a nucleating substrate accounting for grain...In Mg-Ca alloys the grain refining mechanism,in particular regarding the role of nucleant substrates,remains the object of debates.Although native MgO is being recognised as a nucleating substrate accounting for grain refinement of Mg alloys,the possible interactions of MgO with alloying elements that may alter the nucleation potency have not been elucidated yet.Herein,we design casting experiments of Mg-xCa alloys varied qualitatively in number density of native MgO,which are then comprehensively studied by advanced electron microscopy.The results show that grain refinement is enhanced as the particle number density of MgO increases.The native MgO particles are modified by interfacial layers due to the co-segregation of Ca and N solute atoms at the MgO/Mg interface.Using aberration-corrected scanning transmission electron microscopy and electron energy loss spectroscopy,we reveal the nature of these Ca/N interfacial layers at the atomic scale.Irrespective of the crystallographic termination of MgO,Ca and N co-segregate at the MgO/Mg interface and occupy Mg and O sites,respectively,forming an interfacial structure of a few atomic layers.The interfacial structure is slightly expanded,less ordered and defective compared to the MgO matrix due to compositional deviations,whereby the MgO substrate is altered as a poorer template to nucleate Mg solid.Upon solidification in a TP-1 mould,the impotent MgO particles account for the grain refining mechanism,where they are suggested to participate into nucleation and grain initiation processes in an explosive manner.This work not only reveals the atomic engineering of a substrate through interfacial segregation but also demonstrates the effectiveness of a strategy whereby native MgO particles can be harnessed for grain refinement in Mg-Ca alloys.展开更多
In this work,we aim to introduce some modifications to the Anam-Net deep neural network(DNN)model for segmenting optic cup(OC)and optic disc(OD)in retinal fundus images to estimate the cup-to-disc ratio(CDR).The CDR i...In this work,we aim to introduce some modifications to the Anam-Net deep neural network(DNN)model for segmenting optic cup(OC)and optic disc(OD)in retinal fundus images to estimate the cup-to-disc ratio(CDR).The CDR is a reliable measure for the early diagnosis of Glaucoma.In this study,we developed a lightweight DNN model for OC and OD segmentation in retinal fundus images.Our DNN model is based on modifications to Anam-Net,incorporating an anamorphic depth embedding block.To reduce computational complexity,we employ a fixed filter size for all convolution layers in the encoder and decoder stages as the network deepens.This modification significantly reduces the number of trainable parameters,making the model lightweight and suitable for resource-constrained applications.We evaluate the performance of the developed model using two publicly available retinal image databases,namely RIM-ONE and Drishti-GS.The results demonstrate promising OC segmentation performance across most standard evaluation metrics while achieving analogous results for OD segmentation.We used two retinal fundus image databases named RIM-ONE and Drishti-GS that contained 159 images and 101 retinal images,respectively.For OD segmentation using the RIM-ONE we obtain an f1-score(F1),Jaccard coefficient(JC),and overlapping error(OE)of 0.950,0.9219,and 0.0781,respectively.Similarly,for OC segmentation using the same databases,we achieve scores of 0.8481(F1),0.7428(JC),and 0.2572(OE).Based on these experimental results and the significantly lower number of trainable parameters,we conclude that the developed model is highly suitable for the early diagnosis of glaucoma by accurately estimating the CDR.展开更多
Second-generation high-temperature superconducting(HTS)conductors,specifically rare earth-barium-copper-oxide(REBCO)coated conductor(CC)tapes,are promising candidates for high-energy and high-field superconducting app...Second-generation high-temperature superconducting(HTS)conductors,specifically rare earth-barium-copper-oxide(REBCO)coated conductor(CC)tapes,are promising candidates for high-energy and high-field superconducting applications.With respect to epoxy-impregnated REBCO composite magnets that comprise multilayer components,the thermomechanical characteristics of each component differ considerably under extremely low temperatures and strong electromagnetic fields.Traditional numerical models include homogenized orthotropic models,which simplify overall field calculation but miss detailed multi-physics aspects,and full refinement(FR)ones that are thorough but computationally demanding.Herein,we propose an extended multi-scale approach for analyzing the multi-field characteristics of an epoxy-impregnated composite magnet assembled by HTS pancake coils.This approach combines a global homogenization(GH)scheme based on the homogenized electromagnetic T-A model,a method for solving Maxwell's equations for superconducting materials based on the current vector potential T and the magnetic field vector potential A,and a homogenized orthotropic thermoelastic model to assess the electromagnetic and thermoelastic properties at the macroscopic scale.We then identify“dangerous regions”at the macroscopic scale and obtain finer details using a local refinement(LR)scheme to capture the responses of each component material in the HTS composite tapes at the mesoscopic scale.The results of the present GH-LR multi-scale approach agree well with those of the FR scheme and the experimental data in the literature,indicating that the present approach is accurate and efficient.The proposed GH-LR multi-scale approach can serve as a valuable tool for evaluating the risk of failure in large-scale HTS composite magnets.展开更多
Roads are crucial public spaces in cities and serve as a window to showcase the city’s characteristics.They serve not only as a means of urban transportation but also as a crucial spatial carrier for urban communicat...Roads are crucial public spaces in cities and serve as a window to showcase the city’s characteristics.They serve not only as a means of urban transportation but also as a crucial spatial carrier for urban communication activities and a significant location for meeting the increasing demands of people for a better quality of life.The current road infrastructure prioritizes the right of way for cars,neglecting the design of sidewalks and green belts within the road’s boundaries,and extension spaces between buildings and boundary lines of roads.There is a pressing need to improve street space in response to the demand for development transformation and the creation of a warmer city.This paper summarizes common problems in current road spaces,draws on the experience of excellent urban road spaces in foreign countries,discusses new ideas for the refined design of road spaces based on the transformation of road planning concepts,and suggests a reference standard for guiding detailed design.Simultaneously,the review of road construction will incorporate the detailed design of road space to enhance the role of planning in guiding and controlling the construction of road works.展开更多
In this article,we first establish an asymptotically sharp result on the higher order Fréchet derivatives for bounded holomorphic mappings f(x)=f(0)+∞∑s=1Dskf(0)(x^(sk))/(sk)!:B_(X)→B_(Y),where B_X is the unit...In this article,we first establish an asymptotically sharp result on the higher order Fréchet derivatives for bounded holomorphic mappings f(x)=f(0)+∞∑s=1Dskf(0)(x^(sk))/(sk)!:B_(X)→B_(Y),where B_X is the unit ball of X.We next give a sharp result on the first order Fréchet derivative for bounded holomorphic mappings F(X)=F(0+)∞∑s=KD^(s)f(0)(x^(8)/s!):B_(X)→B_(Y),where B_(X)is the unit ball of X.The results that we derive include some results in several complex variables,and extend the classical result in one complex variable to several complex variables.展开更多
Objective: To investigate the application effect of refined nursing care in the care for elderly patients with reflux esophagitis. Methods: Following the difference in nursing style, 84 cases of elderly patients with ...Objective: To investigate the application effect of refined nursing care in the care for elderly patients with reflux esophagitis. Methods: Following the difference in nursing style, 84 cases of elderly patients with reflux esophagitis admitted to our hospital from May 2022 to May 2023 were randomly grouped into a control group and a research group, with 42 cases each. The control group was given conventional nursing care and the research group was given refined nursing care. The psychological state and treatment adherence of the two groups of patients after the nursing intervention were compared. Results: After the nursing intervention, the self-rating anxiety scale (SAS) and self-rating depression scale (SDS) scores of the research group were lower than those of the control group (P < 0.05). The treatment compliance of the research group was better than the control group (P < 0.05). Conclusion: The implementation of refined nursing care for elderly patients with reflux esophagitis exhibited a significant effect on improving the patient’s psychological state, treatment compliance, and rehabilitation.展开更多
This article discusses and analyzes the law of nitrogen increase in liquid steel and the main factors affect-ing the nitrogen increasing of molten steel,through the way of adding nitrogen to molten steel by bottom blo...This article discusses and analyzes the law of nitrogen increase in liquid steel and the main factors affect-ing the nitrogen increasing of molten steel,through the way of adding nitrogen to molten steel by bottom blowing nitrogen gas in LF refining process.It is considered that the main factors affecting the nitrogen increasing instability of molten steel are the initial temperature of LF refining,nitrogen relative element,surface active elements[O]and[S]of steel liquid,and bottom blowing rate of ladle.The large-scale production practice shows that T[O]not more than 50×10-6 and[S]is not more than 0.020 in LF refining at the initial temperature of not less than 1570.The liquid steel nitrogen enrichment test is carried out by ladle bottom blowing nitrogen gas after 20 min of refining,the flow rate is set as(6.0~7.0)NL/min per ton,and it is turned to 2 NL/min at 6 min before the end of refining,the nitrogen increasing rate of liquid steel is basically stable at(5~6)×10-6 per minute.展开更多
Objective:To evaluate the application value of a refined quality control management model for a sterilization supply center.Methods:A retrospective analysis was conducted on the work situation of the sterilization sup...Objective:To evaluate the application value of a refined quality control management model for a sterilization supply center.Methods:A retrospective analysis was conducted on the work situation of the sterilization supply center from January 2021 to January 2023.The work situation before January 31,2022,was classified as the control group;a routine quality control management model was implemented,and the work situation after January 31,2022,was classified as the observation group.The quality of medical device management and department satisfaction between the two groups were compared.Results:The timely recovery and supply rate,classification and cleaning pass rate,disinfection pass rate,packaging pass rate,sterilization pass rate,and department satisfaction score in the observation group were all higher than those of the control group(P<0.05).Conclusion:Implementing a refined quality control management model in the sterilization supply center can improve the quality management level of medical devices and department satisfaction and is worthy of promotion.展开更多
由于 AZ 系变形镁合金属于密排六方结构,其塑性变形性能和机械性能相对较差。采用晶粒细化的方法可大大改善镁合金的力学性能。本文通过对自制的新型晶粒细化剂(Al-Ti-C-RE)与常规的细化剂(MgCO_3)的细化作用的比较发现,新开发的晶粒细...由于 AZ 系变形镁合金属于密排六方结构,其塑性变形性能和机械性能相对较差。采用晶粒细化的方法可大大改善镁合金的力学性能。本文通过对自制的新型晶粒细化剂(Al-Ti-C-RE)与常规的细化剂(MgCO_3)的细化作用的比较发现,新开发的晶粒细化剂 Al-Ti-C-RE 可以更有效地细化镁合金的晶粒,提高 AZ系镁合金的综合力学性能。展开更多
Al-Ti-C grain refiner was prepared by SHS (self-propagating high-temperature synthesis )-melting technique. The effect of La on the microstructures of grain refiner was studied by OM, TEM, SEM, XRD, and EDS. The exp...Al-Ti-C grain refiner was prepared by SHS (self-propagating high-temperature synthesis )-melting technique. The effect of La on the microstructures of grain refiner was studied by OM, TEM, SEM, XRD, and EDS. The experimental results indicate that La can improve the wettability between liquid aluminum and graphite ; the addition of La results in dispersive distribution of TiAl3 and TiC particles in the matrix. An excellent grain refining performance of Al-Ti-C grain refiner on commercially pure Al was obtained.展开更多
An alloy of A1-8wt% Si-0.8wt% Fe was cast in a metallic die, and its microstrucmral changes due to Ti-B refiner and Sr modifier additions were studied. Apart from usual refinement and modification of the microstructur...An alloy of A1-8wt% Si-0.8wt% Fe was cast in a metallic die, and its microstrucmral changes due to Ti-B refiner and Sr modifier additions were studied. Apart from usual refinement and modification of the microstructure, some mutual influences of the additives took place, and no mutual poisoning effects by these additives, in combined form, were observed. It was noticed that the dimensions of the iron-rich intermetallics were influenced by the additives causing them to become larger. The needle-shaped intermetallics that were obtained from refiner addition became thicker and longer when adding the modifier. It was also found that a-Al and eutectic silicon phases preferentially nucleate on different types of intermetallic compounds. The more iron content of the intermetallic compounds and the more changes in their dimensions occurred. Formation of the shrinkage porosities was also observed.展开更多
1 INTRODUCTIONWood chip refining is the most critical step in mechanical pulping.Commercical experi-ences have been gained for years.Modelling and control of chip refiners,however,pose a challenge mainly because of th...1 INTRODUCTIONWood chip refining is the most critical step in mechanical pulping.Commercical experi-ences have been gained for years.Modelling and control of chip refiners,however,pose a challenge mainly because of the stochastic nature of the process.Some attemptshave been made to employ factor analysis technique[1]in the modelling andsimulating of refiner operation[2,3].Strand[2]used common factors as links betweenintrinsic fibre properties and pulp quality.He believed that a qualitative concept onthe physical nature of these common factors could be arrived at,and thus would helpto understand what refining variables need to be controlled or adjusted in order to im-prove pulp quality.However,the linear model used in factor analysis is based on theassumption that the interactions among the system variables are linear,which,ofcourse,is not true in practice.展开更多
基金supported by the Natural Science Foundation of Inner Mongolia Autonomous Region(Grant No.2021MS05049)the Youth Fund Project of State Key Laboratory of Baiyunobo Rare Earth Resource Researches and Comprehensive Utilization(Grant No.2021Z2348)the Project of China North Rare Earth(Group)High-tech Co.,Ltd.(Grant No.2020H2177).
文摘To investigate the effect of rare earth on size and distribution of TiB2 phase in aluminum alloy refiner,Al-5Ti-1B-RE master alloy was fabricated,and its microstructure and phase constitutions were investigated by the combination of first principles calculations and experimental investigation.The calculated results reveal that Ce has the most effective modification ability due to the most positive adsorption energy and the largest charge transfer value compared with other rare earth elements.Results of experimental investigation indicate that the addition of rare earth in the Al-5Ti-1B alloys can greatly refine the particle size of TiB2,improve the distribution of particles and lead to better refinement effect than that of the Al-5Ti-1B alloys without rare earth.Moreover,Ce has the best optimization effect,which agrees well with the calculated results.
基金financially supported by the National Natural Science Foundation of China (No. 51174177)
文摘Commercial A356 alloy was refined with a homemade A1-5Ti-0.25C-2RE master alloy, and the microstructure and macrostructure of the refined alloy were investigated. The results show that the grain refining effect of A356 is poor by the addition level of 0.5 wt% master alloy, but when the level reaches 3.0 wt% the grain can get a satisfactory refining effect. Dendrite of A356 can be effectively refined by addition of 0.5 wt% master alloy; however, the refining effect is not significantly improved by further increasing the addition of master alloy. Grain and dendrite refining effects are compared in this article, and the results show that the grain and dendrite exhibit different refining effects with the same addition level of master alloy. Dendrite is easier to reach the optimal refining effect than grain.
文摘The Al-5Cu alloys were prepared by different treatment methods,including adding a refiner Al-5Ti-1B,exerting a rotating magnetic field(RMF),and compound treatment of both refiner and RMF.The effects of treatment methods on the microstructure,properties,and solid solubility of the Al-5Cu alloy were investigated.The optimal magnetic field parameters and addition amount of refiner were confirmed by experiment.Results show that either RMF or adding refiner Al-5Ti-1B alone can refine the grain size,and the refining effect can be further improved by a compound refining treatment with optimized magnetic field parameters(120 A current and 8 Hz frequency) and 1.0wt.% Al-5Ti-1B refiner(RMF*+Al-5Ti-1B*).The average grain size is decreased to 68.1 μm,which is 60.8%,21.1%,and 83.5% lower than that of the alloy treated by the optimized rotating magnetic field,the Al-5Ti-1B refiner,and the alloy without any treatment,respectively.The tensile strength and elongation of the alloy reach 232.5 MPa and 18.6%,respectively,which are obviously higher than those of the alloys treated by rotating magnetic field,Al-5Ti-1B refiner,and the alloy without any treatment,respectively.Additionally,the solid solubility of the alloy is also obviously improved compared to the alloys treated by other methods.
基金funding from the National Natural Science Foundation of China (Grant No. 50745048)Shaanxi Provincial Key Research and Development Project (Grant No. 2020 GY-105)Natural Science Basic Research Program of Shaanxi (Grant No. 2023-JC-QN-0154)。
文摘Power consumption is the energy source of the impact on fibers or pulp during low-consistency(LC)pulp refining,and the strength of refining affects refining quality and efficiency.The pulp properties,operating parameters,and bar parameters of the refiner plates are important parameters affecting refining efficiency,which can be defined as the ratio of net to total refining power.In this study,LC refining trials for pulps with different consistencies and fiber lengths were conducted using five isometric straightbar plates with different bar angles to explore the influences of the plate bar angle and pulp properties on the no-load power,impact capacity on fibers and refining efficiency.It was found that the no-load power of the LC refining process decreased with an increase in the plate bar angle while increased when pulp with higher consistency was refined under the same refining conditions.However,the effect of pulp consistency on the no-load power can be neglected when refining is conducted using plates with larger bar angles.Meanwhile,a critical bar angle for straight-bar plates in LC refining may exist,which has the strongest impact on the pulp and highest refining efficiency under the same refining conditions.In addition,the impact capacity of the plate on the pulp and refining efficiency in LC refining can be enhanced by appropriately increasing the pulp consistency and average fiber length when the bar angle of the refiner plate with a sector angle of 40°is less than 30°.Therefore,the efficiency and power consumption of the LC refining process can be adjusted by optimizing the pulp consistency and bar parameters of the refining plates.
基金Funded by the Basic Research Project in Shanxi Province(No.202103021224183)。
文摘Through the use of purification and recirculation superheating techniques on molten glass,the Ni65Cu33Co2 alloy was successfully undercooled to a maximum temperature of 292 K.High-speed photography was employed to capture the process of interface migration of the alloy liquid,allowing for an analysis of the relationship between the morphological characteristics of the alloy liquid solidification front and the degree of undercooling.Additionally,the microstructure of the alloy was examined using metallographic microscopy,leading to a systematic study of the microscopic morphological characteristics and evolution laws of the refined structure during rapid solidification.The research reveals that the grain refining mechanism of the Ni-Cu-Co ternary alloy is consistent with that of the binary alloy(Ni-Cu).Specifically,under low undercooling conditions,intense dendritic remelting was found to cause grain refinement,while under high undercooling conditions,recrystallization driven by accumulated stress and plastic strain resulting from the interaction between the liquid flow and the primary dendrites caused by rapid solidification was identified as the main factor contributing to grain refinement.Furthermore,the study highlights the significant role of the Co element in influencing the solidification rate and reheat effect of the alloy.The addition of Co was also found to facilitate the formation of non-segregated solidification structure,indicating its importance in the overall solidification process.
基金financial support under grant number EP/N007638/1supported by EPSRC under grant number EP/W021080/1
文摘In Mg-Ca alloys the grain refining mechanism,in particular regarding the role of nucleant substrates,remains the object of debates.Although native MgO is being recognised as a nucleating substrate accounting for grain refinement of Mg alloys,the possible interactions of MgO with alloying elements that may alter the nucleation potency have not been elucidated yet.Herein,we design casting experiments of Mg-xCa alloys varied qualitatively in number density of native MgO,which are then comprehensively studied by advanced electron microscopy.The results show that grain refinement is enhanced as the particle number density of MgO increases.The native MgO particles are modified by interfacial layers due to the co-segregation of Ca and N solute atoms at the MgO/Mg interface.Using aberration-corrected scanning transmission electron microscopy and electron energy loss spectroscopy,we reveal the nature of these Ca/N interfacial layers at the atomic scale.Irrespective of the crystallographic termination of MgO,Ca and N co-segregate at the MgO/Mg interface and occupy Mg and O sites,respectively,forming an interfacial structure of a few atomic layers.The interfacial structure is slightly expanded,less ordered and defective compared to the MgO matrix due to compositional deviations,whereby the MgO substrate is altered as a poorer template to nucleate Mg solid.Upon solidification in a TP-1 mould,the impotent MgO particles account for the grain refining mechanism,where they are suggested to participate into nucleation and grain initiation processes in an explosive manner.This work not only reveals the atomic engineering of a substrate through interfacial segregation but also demonstrates the effectiveness of a strategy whereby native MgO particles can be harnessed for grain refinement in Mg-Ca alloys.
基金funded byResearchers Supporting Project Number(RSPD2024R 553),King Saud University,Riyadh,Saudi Arabia.
文摘In this work,we aim to introduce some modifications to the Anam-Net deep neural network(DNN)model for segmenting optic cup(OC)and optic disc(OD)in retinal fundus images to estimate the cup-to-disc ratio(CDR).The CDR is a reliable measure for the early diagnosis of Glaucoma.In this study,we developed a lightweight DNN model for OC and OD segmentation in retinal fundus images.Our DNN model is based on modifications to Anam-Net,incorporating an anamorphic depth embedding block.To reduce computational complexity,we employ a fixed filter size for all convolution layers in the encoder and decoder stages as the network deepens.This modification significantly reduces the number of trainable parameters,making the model lightweight and suitable for resource-constrained applications.We evaluate the performance of the developed model using two publicly available retinal image databases,namely RIM-ONE and Drishti-GS.The results demonstrate promising OC segmentation performance across most standard evaluation metrics while achieving analogous results for OD segmentation.We used two retinal fundus image databases named RIM-ONE and Drishti-GS that contained 159 images and 101 retinal images,respectively.For OD segmentation using the RIM-ONE we obtain an f1-score(F1),Jaccard coefficient(JC),and overlapping error(OE)of 0.950,0.9219,and 0.0781,respectively.Similarly,for OC segmentation using the same databases,we achieve scores of 0.8481(F1),0.7428(JC),and 0.2572(OE).Based on these experimental results and the significantly lower number of trainable parameters,we conclude that the developed model is highly suitable for the early diagnosis of glaucoma by accurately estimating the CDR.
基金Project supported by the National Natural Science Foundation of China(Nos.11932008 and 12272156)the Fundamental Research Funds for the Central Universities(No.lzujbky-2022-kb06)+1 种基金the Gansu Science and Technology ProgramLanzhou City’s Scientific Research Funding Subsidy to Lanzhou University of China。
文摘Second-generation high-temperature superconducting(HTS)conductors,specifically rare earth-barium-copper-oxide(REBCO)coated conductor(CC)tapes,are promising candidates for high-energy and high-field superconducting applications.With respect to epoxy-impregnated REBCO composite magnets that comprise multilayer components,the thermomechanical characteristics of each component differ considerably under extremely low temperatures and strong electromagnetic fields.Traditional numerical models include homogenized orthotropic models,which simplify overall field calculation but miss detailed multi-physics aspects,and full refinement(FR)ones that are thorough but computationally demanding.Herein,we propose an extended multi-scale approach for analyzing the multi-field characteristics of an epoxy-impregnated composite magnet assembled by HTS pancake coils.This approach combines a global homogenization(GH)scheme based on the homogenized electromagnetic T-A model,a method for solving Maxwell's equations for superconducting materials based on the current vector potential T and the magnetic field vector potential A,and a homogenized orthotropic thermoelastic model to assess the electromagnetic and thermoelastic properties at the macroscopic scale.We then identify“dangerous regions”at the macroscopic scale and obtain finer details using a local refinement(LR)scheme to capture the responses of each component material in the HTS composite tapes at the mesoscopic scale.The results of the present GH-LR multi-scale approach agree well with those of the FR scheme and the experimental data in the literature,indicating that the present approach is accurate and efficient.The proposed GH-LR multi-scale approach can serve as a valuable tool for evaluating the risk of failure in large-scale HTS composite magnets.
文摘Roads are crucial public spaces in cities and serve as a window to showcase the city’s characteristics.They serve not only as a means of urban transportation but also as a crucial spatial carrier for urban communication activities and a significant location for meeting the increasing demands of people for a better quality of life.The current road infrastructure prioritizes the right of way for cars,neglecting the design of sidewalks and green belts within the road’s boundaries,and extension spaces between buildings and boundary lines of roads.There is a pressing need to improve street space in response to the demand for development transformation and the creation of a warmer city.This paper summarizes common problems in current road spaces,draws on the experience of excellent urban road spaces in foreign countries,discusses new ideas for the refined design of road spaces based on the transformation of road planning concepts,and suggests a reference standard for guiding detailed design.Simultaneously,the review of road construction will incorporate the detailed design of road space to enhance the role of planning in guiding and controlling the construction of road works.
基金supported by the NSFC(11871257,12071130)supported by the NSFC(11971165)。
文摘In this article,we first establish an asymptotically sharp result on the higher order Fréchet derivatives for bounded holomorphic mappings f(x)=f(0)+∞∑s=1Dskf(0)(x^(sk))/(sk)!:B_(X)→B_(Y),where B_X is the unit ball of X.We next give a sharp result on the first order Fréchet derivative for bounded holomorphic mappings F(X)=F(0+)∞∑s=KD^(s)f(0)(x^(8)/s!):B_(X)→B_(Y),where B_(X)is the unit ball of X.The results that we derive include some results in several complex variables,and extend the classical result in one complex variable to several complex variables.
文摘Objective: To investigate the application effect of refined nursing care in the care for elderly patients with reflux esophagitis. Methods: Following the difference in nursing style, 84 cases of elderly patients with reflux esophagitis admitted to our hospital from May 2022 to May 2023 were randomly grouped into a control group and a research group, with 42 cases each. The control group was given conventional nursing care and the research group was given refined nursing care. The psychological state and treatment adherence of the two groups of patients after the nursing intervention were compared. Results: After the nursing intervention, the self-rating anxiety scale (SAS) and self-rating depression scale (SDS) scores of the research group were lower than those of the control group (P < 0.05). The treatment compliance of the research group was better than the control group (P < 0.05). Conclusion: The implementation of refined nursing care for elderly patients with reflux esophagitis exhibited a significant effect on improving the patient’s psychological state, treatment compliance, and rehabilitation.
文摘This article discusses and analyzes the law of nitrogen increase in liquid steel and the main factors affect-ing the nitrogen increasing of molten steel,through the way of adding nitrogen to molten steel by bottom blowing nitrogen gas in LF refining process.It is considered that the main factors affecting the nitrogen increasing instability of molten steel are the initial temperature of LF refining,nitrogen relative element,surface active elements[O]and[S]of steel liquid,and bottom blowing rate of ladle.The large-scale production practice shows that T[O]not more than 50×10-6 and[S]is not more than 0.020 in LF refining at the initial temperature of not less than 1570.The liquid steel nitrogen enrichment test is carried out by ladle bottom blowing nitrogen gas after 20 min of refining,the flow rate is set as(6.0~7.0)NL/min per ton,and it is turned to 2 NL/min at 6 min before the end of refining,the nitrogen increasing rate of liquid steel is basically stable at(5~6)×10-6 per minute.
文摘Objective:To evaluate the application value of a refined quality control management model for a sterilization supply center.Methods:A retrospective analysis was conducted on the work situation of the sterilization supply center from January 2021 to January 2023.The work situation before January 31,2022,was classified as the control group;a routine quality control management model was implemented,and the work situation after January 31,2022,was classified as the observation group.The quality of medical device management and department satisfaction between the two groups were compared.Results:The timely recovery and supply rate,classification and cleaning pass rate,disinfection pass rate,packaging pass rate,sterilization pass rate,and department satisfaction score in the observation group were all higher than those of the control group(P<0.05).Conclusion:Implementing a refined quality control management model in the sterilization supply center can improve the quality management level of medical devices and department satisfaction and is worthy of promotion.
基金Project supported by the Natural Science Foundation of Shanxi Province (20011047)Patent Generalization Project ofShanxi Province (051025)
文摘Al-Ti-C grain refiner was prepared by SHS (self-propagating high-temperature synthesis )-melting technique. The effect of La on the microstructures of grain refiner was studied by OM, TEM, SEM, XRD, and EDS. The experimental results indicate that La can improve the wettability between liquid aluminum and graphite ; the addition of La results in dispersive distribution of TiAl3 and TiC particles in the matrix. An excellent grain refining performance of Al-Ti-C grain refiner on commercially pure Al was obtained.
文摘An alloy of A1-8wt% Si-0.8wt% Fe was cast in a metallic die, and its microstrucmral changes due to Ti-B refiner and Sr modifier additions were studied. Apart from usual refinement and modification of the microstructure, some mutual influences of the additives took place, and no mutual poisoning effects by these additives, in combined form, were observed. It was noticed that the dimensions of the iron-rich intermetallics were influenced by the additives causing them to become larger. The needle-shaped intermetallics that were obtained from refiner addition became thicker and longer when adding the modifier. It was also found that a-Al and eutectic silicon phases preferentially nucleate on different types of intermetallic compounds. The more iron content of the intermetallic compounds and the more changes in their dimensions occurred. Formation of the shrinkage porosities was also observed.
文摘1 INTRODUCTIONWood chip refining is the most critical step in mechanical pulping.Commercical experi-ences have been gained for years.Modelling and control of chip refiners,however,pose a challenge mainly because of the stochastic nature of the process.Some attemptshave been made to employ factor analysis technique[1]in the modelling andsimulating of refiner operation[2,3].Strand[2]used common factors as links betweenintrinsic fibre properties and pulp quality.He believed that a qualitative concept onthe physical nature of these common factors could be arrived at,and thus would helpto understand what refining variables need to be controlled or adjusted in order to im-prove pulp quality.However,the linear model used in factor analysis is based on theassumption that the interactions among the system variables are linear,which,ofcourse,is not true in practice.