Microstructure and Properties of Ti_3Al-base Alloys

In the present paper, the relations between the microstructure and the properties of Ti-14Al-21Nb and Ti-14Al-20Nb-3.5V-2Mo alloys at different temperatures and different cooling rates of heat treatment were re-vealed by X-ray , optical microscope , HVTEM , auto-graphical-analyser and mechanical properties test at roomand high temperature. The experimental results show as follows: at 1040～1120℃ 14h WQ, the microstruc-ture of Ti-14Al-21Nb bar is primary phaseα_2+B2. With temperature increasing, the primary α_2 phase de-crease and the mechanical properties ultimate tensile strength (UTS), yield strength (YS) and elongation(EL) at room temperature increase. When it has reduced the α_2 phase by 50% (at 1080℃/4h WQ) , the me-chanical properties at room temperature are excellent , EL being 10. 5%. Following the α_2 phase reduces contin-uously , UTS, YS are going up, but EL is going down. After heated at two phases range and cooled down tothe room temperature with furnace, the microstructure of Ti-14Al-20Nb-3.5V-2Mo alloy is the equiaxed α_2+needle-like α_2+βphase. The mechanical properties at room temperature and 700℃ are fairly good.

Phase Transformation and Deformation Mechanism of Ti_3Al-base Alloy

The phase transformation and deformation mechanism of the alloy based on composition Ti_3Al with addition of Nb,V,Mo have been studied by use of transmission electron microscopy (TEM).It has been shown that the orientation relationship of α_2 phase transformed from β phase is:(0001)α_2// (l10)β,[1210]α_2//[111]β.The present dislocation slip systems in α_2 phase are (1100)[0001] and (1100)<1120>.There also exist α_2 twins which have new twin relationship and the twin plane is (2021).

Effects of V and Zr Additions on Microstructures and Mechanical Properties of Nb-Ti-Al-Base Alloys

Microstructures and mechanical properties of Nb-32Ti-7Al alloys containing different V and Zr contents were investigated. The microstructures were characterized using optical microscopy and scanning electron microscopy (SEM). The alloy with V and Zr presents single phase Nb solid solution (Nbss). Tensile testing was carried out at room temperature and 1373 K. The results show that these alloys have good ductility at room temperature. The strengths at room and high temperature increase with the addition of V and Zr, but the room temperature ductility decrease.

Microstructure and mechanical properties of TiAl-based alloy prepared by double mechanical milling and spark plasma sintering

A fine-grained TiAl alloy with a composition of Ti-45Al-2Cr-2Nb-1B-0.5Ta-0.225Y （mole fraction, %） was prepared by double mechanical milling（DMM） and spark plasma sintering（SPS）. The relationship among sintering temperature, microstructure and mechanical properties was studied. The results show that the morphology of double mechanical milled powder is regular with size in the range of 20-40 μm and mainly composed of TiAl and Ti3Al phases. The main phase TiAl and few phases Ti3Al, Ti2Al and TiB2 were observed in the SPSed alloys. For samples sintered at 900 ℃ the equiaxed crystal grain microstructure is achieved with size in the range of 100-200 nm. With increasing the SPS temperature from 900 ℃to 1000 ℃ the size of equiaxed crystal grain obviously increases, the microhardness decreases from HV658 to HV616, and the bending strength decreases from 781 MPa to 652 MPa. In the meantime, the compression fracture strength also decreases from 2769 MPa to 2669 MPa, and the strain to fracture in compression increases from 11.69% to 17.76%. On the base of analysis of fractographies, it shows that the compression fracture transform of the SPSed alloys is intergranular rupture.

TEM Specimen Preparation for Al-based Amorphous Alloys

Transmission electron microscopy （TEM） is usually used to identify the amorphicity. However, some artifacts may be introduced due to improper TEM foil preparation. In this paper, three Al-rich metallic glasses with and without a glass transition were selected for characterizing the effect of the electropolishing condition on the as-quenched structure during TEM specimen preparation. It is shown that the occurrence of the modulated bright-dark structure under TEM observation is closely sensitive to the electropolishing condition, which suggests us being careful about the possible artifacts induced by specimen preparation when examining amorphous alloys under TEM.

Correlation between pre-peak in structure factor and physical properties in Al-based amorphous alloys

To study the influence of Fe addition on the Al-based amorphous alloys,the structure and properties of Al84Ni10La6 and Al84Ni9Fe1La6 alloys were investigated through various techniques.The results show that 1% Fe（molar fraction） addition increases the area of the pre-peak in the structure factor and decreases the thermal expansion coefficient difference between the crystalline and amorphous states.1% Fe addition also improves the glass forming ability（GFA）,micro-hardness,fracture toughness,electric resistivity,absolute diamagnetism and corrosion resistance of Al-Ni-La alloys,which is related to the changes of medium-range order and quench-in free volume caused by 1% Fe addition.

Evolution of V-containing phases during preparation of Al-based Al−V master alloys

Al-based Al−V master alloys were prepared by both the stepwise heating melting experiment and stepwise melting cooling experiment with rapid solidification to investigate the transformation of V-containing phases which gave different effects on microstructures and properties of commercial Al alloys and Ti alloys,as both melting and solidification processes affect the evolution of V-containing phases largely.The results showed that the raw Al−50wt.%V alloy consisted of needle-like Al_(3)V phase and Al8V5 phase(matrix),while petal-like Al_(3)V,needle-like Al_(7)V and plate-like Al_(10)V phase were present in the Al−V master alloys.The metastable Al_(7)V phase was evolved from Al_(3)V phase and then evolved into Al_(10)V phase during melting process.The number of Al_(10)V phase increased with the decrease of temperature in the range of 800−1000℃.Petal-like Al_(3)V phases could be transformed from Al_(8)V_(5) phase,pre-precipitated from Al−V molten liquid during melting process and precipitated directly during rapid solidification,respectively.

Crystal Nucleation and Growth of Al-based Alloys Produced by Electrolysis

The nucleation and growth of grains in a series of Al-based alloys produced by electrolysis are observed under SEM. The atomic Ti/AI ratios of the nuclei and the distribution of Ti at certain points are analyzed by point EDS. The particles in different atomic Ti/AI ratios might act as the nuclei of α-Al. At the early stage of growth, the spherical Ti-enriched regions might form around these particles within very limited temperature ranges in which the reactions such as the peritectic reactions etc occur. At the latter stage of growth, the dendrites freely develop in the radial orientations, and the concentration of Ti decreases linearly along the dendrite arm and becomes negligible in the region near the periphery of the dendrite. It is believed that the nucleation is closely related with the number and dispersion of primary spherical areas in the melts, and the segregation of Ti leads to the free growth of dendrite, which is necessary for the formation of equiaxial grains.

INVESTIGATION OF MULTI-STEP THERMO-MECHANICALTREATMENT OF CAN-FORGED TiAl-BASED ALLOY

The effects of a new technology, multi-step thermo-mechanical treatment, on the microstructure, deformation substructure and mechanical properties at ambient and elevated tempemture of can-forged Ti-33 Al-3 Cr-0.5Mo (wt%) Alloy were investigated.The results show that, after multi-step thermo-mechanical treatment of can-forged specimens, homogeneous, fine microstructures can be obtained in the whole TiAl-based alloy specimens. Furthermore, the specimen with homogeneous and fine full lamellae microstructure demonstrutes excellent comprehensive mechanical properties at ambient and elevated temperature.

Relationship between the unique microstructures and behaviors of high-entropy alloys

High-entropy alloys(HEAs),which were introduced as a pioneering concept in 2004,have captured the keen interest of nu-merous researchers.Entropy,in this context,can be perceived as representing disorder and randomness.By contrast,elemental composi-tions within alloy systems occupy specific structural sites in space,a concept referred to as structure.In accordance with Shannon entropy,structure is analogous to information.Generally,the arrangement of atoms within a material,termed its structure,plays a pivotal role in dictating its properties.In addition to expanding the array of options for alloy composites,HEAs afford ample opportunities for diverse structural designs.The profound influence of distinct structural features on the exceptional behaviors of alloys is underscored by numer-ous examples.These features include remarkably high fracture strength with excellent ductility,antiballistic capability,exceptional radi-ation resistance,and corrosion resistance.In this paper,we delve into various unique material structures and properties while elucidating the intricate relationship between structure and performance.

CONSTITUTION OF Al-BASE MULTI-COMPONENT QUASI-CRYSTALLINE ALLOYS

ＣＯＮＳＴＩＴＵＴＩＯＮＯＦＡｌ－ＢＡＳＥＭＵＬＴＩ－ＣＯＭＰＯＮＥＮＴＱＵＡＳＩ－ＣＲＹＳＴＡＬＬＩＮＥＡＬＬＯＹＳＣｈｅｎＺｈｅｎｈｕａ；ＪｉａｎｇＸｉａｎｇｙａｎｇ；ＺｈｏｕＤｕｏｓａｎ；ＷａｎｇＹｕｎ；ＨｕａｎｇＰｅｉｙｕｎ（Ｒｅｓｅａｒｃｈ...

Effect of Cr on microstructure and oxidation behavior of TiAl-based alloy with high Nb

Three novel multi-microalloying TiAl-based alloys containing high Nb were designed and fabricated Thermogravimetric method was applied to investigate the influence of Cr on the oxidation behavior of high Nb TiAl alloy at 1,073 K for 200 h in laboratory air. The 2 at.% and 4 at.% Cr were added into the alloy,(respectivel named 2 Cr and 4 Cr compared to the Cr-free ternary alloy, 0 Cr alloy). The alloys' microstructure and compositio as well as the composition distribution of the oxidation scale were analyzed by means of Scanning Electro Microscopy(SEM), Energy Dispersive Spectroscopy(EDS), and X-Ray Diffractometry(XRD). The results show that the addition of Cr decreases the grain size of the Nb-TiAl alloy and leads to a transformation from a full lamellar structure to a nearly fully lamellar structure. When oxidized at 1,073 K for 200 h, the oxidized mass gai of the alloy increases with an increase in Cr addition amount in the first 100 h and decreases in the last 100 h With the increase of Cr content, the oxidation surface turns compact but uneven in morphology, which may affec the oxidation resistance of the alloy by increasing the peeling off risk of the oxidation layer at friction conditions.

Interface structure and formation mechanism of diffusion-bonded joints of TiAl-based alloy to titanium alloy

Vacuum diffusion bonding of a TiAl based alloy (TAD) to a titanium alloy (TC2) was carried out at 1 273 K for 15～120 min under a pressure of 25 MPa . The kinds of the reaction products and the interface structures of the joints were investigated by SEM, EPMA and XRD. Based on this, a formation mechanism of the interface structure was elucidated. Experimental and analytical results show that two reaction layers have formed during the diffusion bonding of TAD to TC2. One is Al rich α(Ti)layer adjacent to TC2,and the other is (Ti 3Al+TiAl)layer adjacent to TAD,thus the interface structure of the TAD/TC2 joints is TAD/(Ti 3Al+TiAl)/α(Ti)/TC2.This interface structure forms according to a three stage mechanism,namely(a)the occurrence of a single phase α(Ti)layer;(b)the occurrence of a duplex phase(Ti 3Al+TiAl)layer;and(c)the growth of the α(Ti)and (Ti 3Al+TiAl)layers.

Microstructure and damping properties of LPSO phase dominant Mg-Ni-Y and Mg-Zn-Ni-Y alloys

This work studied the microstructure,mechanical properties and damping properties of Mg_(95.34)Ni_(2)Y_(2.66) and Mg_(95.34)Zn_(1)Ni_(1)Y_(2.66)alloys systematically.The difference in the evolution of the long-period stacked ordered(LPSO)phase in the two alloys during heat treatment was the focus.The morphology of the as-cast Mg_(95.34)Ni_(2)Y_(2.66)presented a disordered network.After heat treatment at 773 K for 2 hours,the eutectic phase was integrated into the matrix,and the LPSO phase maintained the 18R structure.As Zn partially replaced Ni,the crystal grains became rounded in the cast alloy,and lamellar LPSO phases and more solid solution atoms were contained in the matrix after heat treatment of the Mg_(95.34)Zn_(1)Ni_(1)Y_(2.66)alloy.Both Zn and the heat treatment had a significant effect on damping.Obvious dislocation internal friction peaks and grain boundary internal friction peaks were found after temperature-dependent damping of the Mg_(95.34)Ni_(2)Y_(2.66)and Mg_(95.34)Zn_(1)Ni_(1)Y_(2.66)alloys.After heat treatment,the dislocation peak was significantly increased,especially in the alloy Mg_(95.34)Ni_(2)Y_(2).66.The annealed Mg_(95.34)Ni_(2)Y_(2.66)alloy with a rod-shaped LPSO phase exhibited a good damping performance of 0.14 atε=10^(−3),which was due to the difference between the second phase and solid solution atom content.These factors also affected the dynamic modulus of the alloy.The results of this study will help in further development of high-damping magnesium alloys.

High corrosion and wear resistant electroless Ni–P gradient coatings on aviation aluminum alloy parts

A Ni–P alloy gradient coating consisting of multiple electroless Ni–P layers with various phosphorus contents was prepared on the aviation aluminum alloy. Several characterization and electrochemical techniques were used to characterize the different Ni–P coatings’ morphologies, phase structures, elemental compositions, and corrosion protection. The gradient coating showed good adhesion and high corrosion and wear resistance, enabling the application of aluminum alloy in harsh environments. The results showed that the double zinc immersion was vital in obtaining excellent adhesion (81.2 N). The optimal coating was not peeled and shredded even after bending tests with angles higher than 90°and was not corroded visually after 500 h of neutral salt spray test at 35℃. The high corrosion resistance was attributed to the misaligning of these micro defects in the three different nickel alloy layers and the amorphous structure of the high P content in the outer layer. These findings guide the exploration of functional gradient coatings that meet the high application requirement of aluminum alloy parts in complicated and harsh aviation environments.

EFFECTS OF Ca ADDITIONON TiAl-BASED ALLOYS

ＥＦＦＥＣＴＳＯＦＣａＡＤＤＩＴＩＯＮＯＮＴｉＡｌＢＡＳＥＤＡＬＬＯＹＳ①①ＣａｏＰｅｎｇ，ＨｕａｎｇＢａｉｙｕｎ，ＨｅＹｕｅｈｕｉ，ＱｕＸｕａｎｈｕｉＰｏｗｄｅｒＭｅｔａｌｕｒｇｙＲｅｓｅａｒｃｈＩｎｓｔｉｔｕｔｅ，ＣｅｎｔｒａｌＳｏｕｔｈＵｎｉ...

Influence of Process Variables on the Structure of Mechanically Alloyed Ti_3Al-base Intermetallics

During mechanical alloying variables such as the type of mill,milling intensity,milling time,milling at- mosphere and ball-to-powder weight ratio(BPR)affect the morphology and constitution of the product. The effect of milling time,milling atmosphere and BPR on the nature of the product formed in mechanical- ly alloyed pure Ti and blended elemental binary Ti-Al,and ternary Ti-AI-Nb alloy powders was described. Mechanical alloying of pure titanium results,after long milling times,in the formation of an fcc phase.In the binary alloy,a solid solution of aluminum in titanium,an amorphous phase,and a fcc phase form with increasing milling time.The fcc phase,which is probably a result of TiN formation,occurs more rapidly in air or nitrogen than in an inert atmosphere.Formation of the B2 phase in the ternary alloys depends both on alloy composition and the milling atmosphere,with 100％ formation in all atmospheres in Ti-25Al-25Nb but not in Ti-24Al-11Nb,and an inert atmosphere favoring formation.The times required for the formation of the different phases decrease as the BPR increases;but their sequence is unaffected.Based on this infor- mation,“milling maps”which describe phase formation as a function of the BPR and milling time are con- structed.Contamination from the milling balls increased as the BPR was increased.

Influence of heat treatment on microstructure,mechanical and corrosion behavior of WE43 alloy fabricated by laser-beam powder bed fusion

Magnesium(Mg)alloys are considered to be a new generation of revolutionary medical metals.Laser-beam powder bed fusion(PBF-LB)is suitable for fabricating metal implants withpersonalized and complicated structures.However,the as-built part usually exhibits undesirable microstructure and unsatisfactory performance.In this work,WE43 parts were firstly fabricated by PBF-LB and then subjected to heat treatment.Although a high densification rate of 99.91%was achieved using suitable processes,the as-built parts exhibited anisotropic and layeredmicrostructure with heterogeneously precipitated Nd-rich intermetallic.After heat treatment,fine and nano-scaled Mg24Y5particles were precipitated.Meanwhile,theα-Mg grainsunderwent recrystallization and turned coarsened slightly,which effectively weakened thetexture intensity and reduced the anisotropy.As a consequence,the yield strength and ultimate tensile strength were significantly improved to(250.2±3.5)MPa and(312±3.7)MPa,respectively,while the elongation was still maintained at a high level of 15.2%.Furthermore,the homogenized microstructure reduced the tendency of localized corrosion and favoredthe development of uniform passivation film.Thus,the degradation rate of WE43 parts was decreased by an order of magnitude.Besides,in-vitro cell experiments proved their favorable biocompatibility.

MICROSTRUCTURE AND TENSILE PROPERTIES OF Fe_3Al-BASED ALLOYS WITH VC AND TiC ADDITIONS

Microstructure and tensile properties of Fe3 Al-based alloys with the additions of TiC and VC particles have been investigated. Results show that the formation of TiC particles results in the refinement of the macrostructure of as-cast ingots. Although the addition of VC particles does not cause any significant change of the as-cast microstructure, the microstructure of the alloy after hot-working and recrystallization has been found to be refined. The formation of both VC and TiC particles results in the increase of yield strength, especially at the high temperature of 600°C.

Effect of cooling rate on the microstructure of electron beam welded joints of two-phase TiAl-based alloy

The analysis of the microstructural characterization and phase composition of electron beam welded joint zones of Ti- 43Al-9V-O. 3Y alloy has been done in this study. The welded seam is mainly composed of B2 phase, the partial γ ＋ α2 twophase lamellar structure and granular γm phase. And the lanthanon Y existed as YAl2 phase and served as grain refined. The impact of different cooling rates on joint microstructure, fracture characteristic and tensile strength were investigated. The high cooling rate restrained the structural transformation and resulted in the ordering structure. The fracture of the joint was brittle cleavage fracture because the ordering structure went against restraining the crack propagation. With the decrease of cooling rate, the transformation amounts of lamellar structure increased, and the fracture presented the layered and crosslayered characteristic.