Al2_3/Al2O3 Joint Brazed with Al2O3-particulate-contained Composite Ag-Cu-Ti Filler Material

Microstructure and interracial reactions of Al2O3 joints brazed with Al2O3-particulate-contained composite Ag-Cu-Ti filler material were researched by scanning electron microscopy （SEM）, electron probe microscopy analysis （EPMA）, energy dispersive spectroscopy （EDS） and X-ray diffraction （XRD）. The interracial reaction layer thickness of joints brazed with conventional active filler metal and active composite filler materials with different volume fraction of Al2O3 particulate was also studied. The experimental results indicated although there were Al2O3 particulates added into active filler metals, the time dependence of interracial layer growth of joints brazed with active composite filler material is t^1/2 as described by Fickian law as the joints brazed with conventional active filler metal.

Morphology and Frictional Characteristics Under Electrical Currents of Al_2O_3/Cu Composites Prepared by Internal Oxidation

Two Al2O3/Cu composites containing 0.24 wt.% Al2O3 and 0.60 wt.% Al2O3 separately are prepared by internal oxidation. Effects of sliding speed and pressure on the frictional characteristics of the composites and copper against brass are investigated and compared. The changes in morphology of the sliding surface and subsurface are examined with scanning electron microscope （SEM） and energy dispersive X-ray spectrum （EDS）. The results show that the wear resistance of the Al2O3/Cu composites is superior to that of copper under the same conditions, Under a given electrical current, the wear rate of Al2O3/Cu composites decreases as the Al2O3-content increases, However, the wear rates of the Al2O3/Cu composites and copper increase as the sliding speed and pressure increase under dry sliding condition. The main wear mechanisms for Al2O3/Cu composites are of abrasion and adhesion; for copper, it is adhesion, although wear by oxidation and electrical erosion can also be observed as the speed and pressure rise.

Properties of Hot-Pressed Al_2O_3-Fe Composites

Alumina-(0 similar to 20 vol. pct) iron composites were fabricated by hot-pressing of well-mixed-alumina and iron powders at 1400 degreesC and 30 MPa for 30 min. Hot-pressed bodies with nearly theoretical density were obtained for addition up to 10 vol. pct Fe, but relative density decreased gradually with further increase in Fe addition. The materials exhibit a homogeneous dispersion of Fe. Fracture strength of the composites exhibits a maximum value of 604 MPa at 15 vol. pct Fe, which is 1.5 times that of alumina alone. Fracture toughness increases with the increase in Fe content, reaching 7.5 MPa.m(1/2) at 20 vol. pct Fe. The theoretical values of fracture toughness was calculated and compared with the experimental one. Toughening mechanisms of the composites are also discussed.

Effects of Cerium on the Mechanical Properties of the ZA22／Al_2O_3 Composites

ZA22/Al2O3 composites were prepared by means of squeeze casting process. The effects of Ce on the ultimate tensile strength (UTS), impact toughness, and hardness of the composites were studied. The results show that both the UTS and the hardness are improved and the impact toughness is decreased with the increase of the volume fraction of fibers (Vf). After Ce is added ,UTS (Vf>15%) and the hardness are improved at room temperature because of the modification of Ce, but the impact toughness and UTS at elevated temperature are lowered.The filtered action of the fiber preform results in that the influence of the amount of Ce added from 0. 1 wt% to 0. 5 wt% on the mechanical properties of the composites can be ignored.

Preparation of Al_2O_3-SiO_2-TiO_2-ZrO_2 Composite Ceramic Membranes by Sol-Gel Method

Al 2O 3-SiO 2-TiO 2-ZrO 2 supported membranes were prepar ed by Sol-Gel method. These composite ceramic membranes are level, even and no macro crack. There exist several crystalline phases such as Al 2O 3, TiO 2(a natase), Al 2SiO 5, and ZrO 2 in these membranes. Changing the molar ratio of Al∶Si∶Ti∶Zr,the kinds and content of crystal phases of composite membranes could be different, which may lead to a variety of microstructure of membranes. The surface nanoscale topography and microstructure of membranes were investiga ted by XRD,SEM,AFM,EPMA. The effects of additives and heat treatments on the sur face nanoscale topography and microstructure of composite ceramic membranes were also analyzed.

β-Sialon-Al_2O_3-SiC系复相材料的研制和性能

研究了在 15 0 0℃的流动氮气中 ,用Al粉、Si粉、Al2 O3粉、刚玉和SiC的颗粒及细粉直接制备 β Sialon -Al2 O3-SiC系复相材料的氮化烧结技术。XRD和SEM分析表明 ,结合相 β Sialon的显微形貌随刚玉量的增加由纤维状向棱柱状转变 ,发育良好。复相材料的高温抗折强度高于常温抗折强度。抗热震试验结果显示 :添加适量的刚玉对β Sialon -SiC复相材料和添加适量的SiC对β Sialon -刚玉 复相材料都具有良好的增韧效果 ,这是β Sialon的纤维增强及柱状晶体原位自补强增韧和复合弥散相增韧综合作用的结果。抗碱和抗高炉渣试验均显示了该复相材料优良的抗碱和抗铁渣侵蚀能力。

Sol-Gel法制备Al_2O_3-SiO_2-TiO_2-ZrO_2复合陶瓷膜的研究

将Sol-Gel法应用于无机膜的制备,成功的研制出一种新型的膜面平整、膜厚均匀且无宏观缺陷的Al2O3-SiO2-TiO2-ZrO2复合陶瓷膜,复合膜含有γ-Al2O3、SiO2、TiO2、ZrO2和Al2SiO5等晶相,改变体系组成含量,晶相组成和含量随之变化,从而引起膜的显微结构的变化。利用XRD、SEM、AFM、EPMA等测试手段重点研究了膜的表面形貌和显微结构,并分析了添加剂、热处理方式等对膜的表面形貌和显微结构影响。

Preliminary Study on Combining K2O-Al2O3-SiO2 System Dental Glass Ceramic with Al2O3 Ceramic

Relationship between K2O-Al2O3-SiO2 system dental glass ceramics and Al2O3 ceramics was investigated. 4 groups of glass ceramic with the same components but different thickness（0.8, 1.2, 1.6, and 2.0 mm） were sintered on Al2O3 base ceramics according to the same thermal treatment system of leucite micro-crystallization reported in previous literatures. The products of each group were analyzed by polarizing microscope, X-ray diffractometer, and an INSTRON material testing machine. Under the thermal treatment system, leucite crystals were formed in samples of each group, and dispersed evenly. Meanwhile, the compressive strengths of group 3 and group 4 were higher than those of group 1 and group 2. Samples of group 3 showed better mechanical properties than others. The conclusions are drawn that Leucite crystals can be controlled in K2O-Al2O3-SiO2 system glass ceramic-Al2O3 ceramic composite material, and the thickness of glass ceramic has a notable influence on the compressive strength of this ceramic composite material.

Development of non-shrinkable ceramic composites for use in high-power microwave tubes

Al_2O_3–CaO–SiC-based ceramic composites with four different compositions were sintered at 1700℃ for 3 h in an air furnace. The phase analysis, microstructural characterization, and elemental composition determination of the developed composites were performed by X-ray diffraction(XRD), field-emission scanning electron microscopy(FESEM), and energy-dispersive X-ray(EDAX) analysis, respectively. The shrinkage, thermal properties, and electrical resistivity of the composites were also studied. The experimental results showed the effects of adding silicon carbide and calcia to alumina on the thermal, electrical, and shrinkage properties of the resultant composites. Among the four investigated ceramic composites, the one composed of 99 wt% alumina, 0.5 wt% CaO, and 0.5 wt% SiC exhibited the best characteristics for use as a potting material in a dispenser cathode of a microwave tube. The material exhibited slight expansion instead of shrinkage during drying or firing. Other properties of the composite powder, such as its thermal properties and electrical resistivity, were comparable to those of a commercial alumina powder.

Relationship between powder characteristic and internal oxidation of Al in Cu-Al pre-alloyed powders

Since Cu-Al powder characteristics have important effects on the preparation of Cu/Al2O3 composite, the apparent activation energy of Al internal oxidation reaction in Cu-Al pre-alloyed powders with different characteristics was calculated in the present investigation. The microstructure and properties of the synthesized Cu/Al2O3 were studied. The results show that high-energy milling can obviously promote internal oxidation of Al in Cu-Al powders in the same solid solubility. At the same milling conditions and internal oxidation parameters, the solid solution of Al in Cu either in low or high amount will result in the poor microstructure and properties of the Cu/Al2O3 composite. Subsequently, when high-energy milling and internal oxidation are synchronously used to prepare the Cu/Al2O3 composite, there should be an appropriate solubility and milling effect for the pre-alloyed powders.

(La0.2Ce0.2Nd0.2Sm0.2Eu0.2)PO4: A high-entropy rare-earth phosphate monazite ceramic with low thermal conductivity and good compatibility with Al2O3

Low thermal conductivity, matched thermal expansion coefficient and good compatibility are general requirements for the environmental/thermal barrier coatings(EBCs/TBCs) and interphases for Al2O3 f/Al2O3 composites. In this work, a novel high-entropy(HE) rare-earth phosphate monazite ceramic (La0.2Ce0.2Nd0.2Sm0.2Eu0.2)PO4 is designed and successfully synthesized. This new type of HE rare-earth phosphate monazite exhibits good chemical compatibility with Al2O3, without reaction with Al2O3 as high as 1600℃ in air. Moreover, the thermal expansion coefficient(TEC) of HE (La0.2Ce0.2Nd0.2Sm0.2Eu0.2)PO4(8.9 × 10^-6/℃ at 300–1000℃) is close to that of Al2O3. The thermal conductivity of HE (La0.2Ce0.2Nd0.2Sm0.2Eu0.2)PO4 at room temperature is as low as 2.08 W·m^-1·K^-1, which is about 42% lower than that of La PO4. Good chemical compatibility, close TEC to that of Al2O3, and low thermal conductivity indicate that HE (La0.2Ce0.2Nd0.2Sm0.2Eu0.2)PO4 is suitable as a candidate EBC/TBC material and an interphase for Al2O3 f/Al2O3 composites.

锌离子电池锰基正极材料研究进展

可充电水系锌离子电池是一种环保且电化学性能优异的二次电池,但锰基正极材料在充放电过程中结构易坍塌、导电率低、稳定性差等缺点严重制约了水系锌离子电池的发展。笔者首先阐述了锰基正极材料中锌离子的储存机理,主要有Zn^(2+)嵌入/脱出机理、H+/Zn^(2+)共嵌入/脱出机理和化学转化反应机理。Zn^(2+)嵌入/脱出机理包括无相变反应和新相生成反应。而新相生成反应又分为可逆相变和不可逆相变。然后,基于锰基正极材料面临的问题,讨论了改善其储锌性能的主要方法。目前可采用的方法包括缺陷工程、与导电材料复合、离子掺杂、表面修饰技术等。用以上方法改进后的锰基正极材料表现出了更加优异的性能。