The occurrence modes of alkali and alkaline-earth metals(AAEMs) in coal relate to their release behavior and ash formation during combustion. To better understand the transformation of AAEMs,the release behavior of ...The occurrence modes of alkali and alkaline-earth metals(AAEMs) in coal relate to their release behavior and ash formation during combustion. To better understand the transformation of AAEMs,the release behavior of water-soluble,HCl-soluble,HCl-insoluble AAEMs during Shenmu coal(SM coal) oxy-fuel combustion in the presence of SO2 and H2O in a drop-tube reactor was investigated through serial dissolution using H2O and HCl solutions. The results show that the release rates of AAEMs increase with an increase in temperature under the three atmospheres studied. The high release rates of Mg and Ca from SM coal are dependent on the high content of soluble Mg and Ca in SM coal. SO2 inhibits the release rates of AAEMs,while H2O promotes them. The effects of SO2 and H2O on the Na and K species are more evident than those on Mg and Ca species. All three types of AAEMs in coal can volatilize in the gas phase during coal combustion. The W-type AAEMs release excessively,whereas the release rates of I-type AAEMs are relatively lower. Different types of AAEM may interconvert through different pathways under certain conditions. Both SO2 and H2O promote the transformation reactions. The effect of SO2 was related to sulfate formation and the promotion by H2O occurs because of a decrease in the melting point of the solid as well as the reaction of H2O.展开更多
Nano-sized γ-alumina (γ-Al2O3) was first prepared by a precipitation method. Then, active component of cobalt and a series of alkaline- earth metal promoters or nickel (Ni) with different contents were loaded on...Nano-sized γ-alumina (γ-Al2O3) was first prepared by a precipitation method. Then, active component of cobalt and a series of alkaline- earth metal promoters or nickel (Ni) with different contents were loaded on the γ-Al2O3 support. The catalysts were characterized by N2 adsorption-desorption, X-ray diffraction (XRD) and thermogravimetry analysis (TGA). The activity and selectivity of the catalysts in catalytic partial oxidation (CPO) of methane have been compared with Co/γ-Al2O3, and it is found that the catalytic activity, selectivity, and stability are enhanced by the addition of alkaline-earth metals and nickel. The optimal loadings of strontium (Sr) and Ni were 6 and 4 wt%, respectively. This finding will be helpful in designing the trimetallic Co-Ni-Sr/γ-Al2O3 catalysts with high performance in CPO of methane展开更多
Solvothermal reactions of Ca(NO), Sr(NO)with thiophene-2,5-dicarboxylic in DMF afforded two new inorganic-organic hybrid frameworks, [M(TDC)(DMF)]n(M = Ca(1), Sr(2), TDC = thiophene-2,5-dicarboxylic, DMF = N,N?-dimeth...Solvothermal reactions of Ca(NO), Sr(NO)with thiophene-2,5-dicarboxylic in DMF afforded two new inorganic-organic hybrid frameworks, [M(TDC)(DMF)]n(M = Ca(1), Sr(2), TDC = thiophene-2,5-dicarboxylic, DMF = N,N?-dimethylformamide), which have been characterized by single-crystal X-ray diffraction, powder X-ray diffraction, elemental analysis and IR spectra. Both compounds feature three-dimensional(3D) frameworks based on the versatile coordinated modes(μ-η~2:η~2, μ-η~2:η~1, μ-η~2:η~1) of carboxylic groups in tdc ligands. C–H···S hydrogen bonds and C–H···π interactions contribute to the stabilization of the structures. They exhibit weaker packing force compared with their literature isomers. Consequently, blue and blue/green luminescence of two compounds has been observed. Their luminescence mechanism can be ascribed to ligand-to-metal charge transfer(LMCT) compared with the ligand-centered luminescence in their isomers. Electronic structural calculations illustrate that under the condition of weaker packing forces, larger gaps can be achieved, which facilitate the LMCT. This work suggests that the introduction of S-heteroatom can result in more electrons rich in the metal centers, thus giving rise to metal-involved luminescence.展开更多
The performance of catalysts used in after-treatment systems is the key factor for the removal of diesel soot,which is an important component of atmosphericfine particle emissions.Herein,three-dimensionally ordered ma...The performance of catalysts used in after-treatment systems is the key factor for the removal of diesel soot,which is an important component of atmosphericfine particle emissions.Herein,three-dimensionally ordered macroporous–mesoporous Ti_(x)Si+(1-x)O_(2)(3DOM-m Ti_(x)Si+(1-x)O_(2)) and its supported MnO_(x)catalysts doped with different alkali/alkaline-earth metals (AMnO_(x)/3 DOM-m Ti_(0.7)Si_(0.3)O_(2)(A:Li,Na,K,Ru,Cs,Mg,Ca,Sr,Ba)) were prepared by mesoporous template (P123)-assisted colloidal crystal template (CCT) and incipient wetness impregnation methods,respectively.Physicochemical characterizations of the catalysts were performed using scanning electron microscopy,X-ray diffraction,N_(2)adsorption–desorption,H_(2)temperature-programmed reduction,O_(2)temperature-programmed desorption,NO temperature-programmed oxidation,and Raman spectroscopy techniques;then,we evaluated their catalytic performances for the removal of diesel soot particles.The results show that the 3DOM-m Ti_(0.7)Si_(0.3)O_(2)supports exhibited a well-defined 3DOM-m nanostructure,and AMnO_(x)nanoparticles with 10–50 nm were evenly dispersed on the inner walls of the uniform macropores.In addition,the as-prepared catalysts exhibited good catalytic performance for soot combustion.Among the prepared catalysts,CsMnO_(x)/3DOM-m Ti_(0.7)Si_(0.3)O_(2)had the highest catalytic activity for soot combustion,with T10,T50,and T90(the temperatures corresponding to soot conversion rates of 10%,50%,and 90%) values of 285,355,and 393℃,respectively.The high catalytic activity of the CsMnO_(x)/3 DOM-m Ti_(0.7)Si_(0.3)O_(2)catalysts was attributed to their excellent low-temperature reducibility and homogeneous macroporous–mesoporous structure,as well as to the synergistic effects between Cs and Mn species and between CsMnO_(x)and the Ti_(0.7)Si_(0.3)O_(2)support.展开更多
Transition metal phosphides(TMPs)have been regarded as alternative hydrogen evolution reaction(HER)and oxygen evolution reaction(OER)catalysts owing to their comparable activity to those of noble metal-based catalysts...Transition metal phosphides(TMPs)have been regarded as alternative hydrogen evolution reaction(HER)and oxygen evolution reaction(OER)catalysts owing to their comparable activity to those of noble metal-based catalysts.TMPs have been produced in various morphologies,including hollow and porous nanostructures,which are features deemed desirable for electrocatalytic materials.Templated synthesis routes are often responsible for such morphologies.This paper reviews the latest advances and existing challenges in the synthesis of TMP-based OER and HER catalysts through templated methods.A comprehensive review of the structure-property-performance of TMP-based HER and OER catalysts prepared using different templates is presented.The discussion proceeds according to application,first by HER and further divided among the types of templates used-from hard templates,sacrificial templates,and soft templates to the emerging dynamic hydrogen bubble template.OER catalysts are then reviewed and grouped according to their morphology.Finally,prospective research directions for the synthesis of hollow and porous TMP-based catalysts,such as improvements on both activity and stability of TMPs,design of environmentally benign templates and processes,and analysis of the reaction mechanism through advanced material characterization techniques and theoretical calculations,are suggested.展开更多
The metal-organic framework(MOF)derived Ni–Co–C–N composite alloys(NiCCZ)were“embedded”inside the carbon cloth(CC)strands as opposed to the popular idea of growing them upward to realize ultrastable energy storag...The metal-organic framework(MOF)derived Ni–Co–C–N composite alloys(NiCCZ)were“embedded”inside the carbon cloth(CC)strands as opposed to the popular idea of growing them upward to realize ultrastable energy storage and conversion application.The NiCCZ was then oxygen functionalized,facilitating the next step of stoichiometric sulfur anion diffusion during hydrothermal sulfurization,generating a flower-like metal hydroxysulfide structure(NiCCZOS)with strong partial implantation inside CC.Thus obtained NiCCZOS shows an excellent capacity when tested as a supercapacitor electrode in a three-electrode configuration.Moreover,when paired with the biomass-derived nitrogen-rich activated carbon,the asymmetric supercapacitor device shows almost 100%capacity retention even after 45,000 charge–discharge cycles with remarkable energy density(59.4 Wh kg^(-1)/263.8μWh cm^(–2))owing to a uniquely designed cathode.Furthermore,the same electrode performed as an excellent bifunctional water-splitting electrocatalyst with an overpotential of 271 mV for oxygen evolution reaction(OER)and 168.4 mV for hydrogen evolution reaction(HER)at 10 mA cm−2 current density along with 30 h of unhinged chronopotentiometric stability performance for both HER and OER.Hence,a unique metal chalcogenide composite electrode/substrate configuration has been proposed as a highly stable electrode material for flexible energy storage and conversion applications.展开更多
Aqueous Zn metal batteries(AZMBs)with intrinsic safety,high energy density and low cost have been regarded as promising electrochemical energy storage devices.However,the parasitic reaction on metallic Zn anode and th...Aqueous Zn metal batteries(AZMBs)with intrinsic safety,high energy density and low cost have been regarded as promising electrochemical energy storage devices.However,the parasitic reaction on metallic Zn anode and the incompatibility between electrode and electrolytes lead to the deterioration of electrochemical performance of AZMBs during the cycling.The critical point to achieve the stable cycling of AZMBs is to properly regulate the zinc ion solvated structure and transfer behavior between metallic Zn anode and electrolyte.In recent years,numerous achievements have been made to resolve the formation of Zn dendrite and interface incompatible issues faced by AZMBs via optimizing the sheath structure and transport capability of zinc ions at electrode-electrolyte interface.In this review,the challenges for metallic Zn anode and electrode-electrolyte interface in AZMBs including dendrite formation and interface characteristics are presented.Following the influences of different strategies involving designing advanced electrode structu re,artificial solid electrolyte interphase(SEI)on Zn anode and electrolyte engineering to regulate zinc ion solvated sheath structure and transport behavior are summarized and discussed.Finally,the perspectives for the future development of design strategies for dendrite-free Zn metal anode and long lifespan AZMBs are also given.展开更多
The widespread adoption of lithium-ion batteries has been driven by the proliferation of portable electronic devices and electric vehicles,which have increasingly stringent energy density requirements.Lithium metal ba...The widespread adoption of lithium-ion batteries has been driven by the proliferation of portable electronic devices and electric vehicles,which have increasingly stringent energy density requirements.Lithium metal batteries(LMBs),with their ultralow reduction potential and high theoretical capacity,are widely regarded as the most promising technical pathway for achieving high energy density batteries.In this review,we provide a comprehensive overview of fundamental issues related to high reactivity and migrated interfaces in LMBs.Furthermore,we propose improved strategies involving interface engineering,3D current collector design,electrolyte optimization,separator modification,application of alloyed anodes,and external field regulation to address these challenges.The utilization of solid-state electrolytes can significantly enhance the safety of LMBs and represents the only viable approach for advancing them.This review also encompasses the variation in fundamental issues and design strategies for the transition from liquid to solid electrolytes.Particularly noteworthy is that the introduction of SSEs will exacerbate differences in electrochemical and mechanical properties at the interface,leading to increased interface inhomogeneity—a critical factor contributing to failure in all-solidstate lithium metal batteries.Based on recent research works,this perspective highlights the current status of research on developing high-performance LMBs.展开更多
Two-dimensional(2D)topological materials have recently garnered significant interest due to their profound physical properties and promising applications for future quantum nanoelectronics.Achieving various topologica...Two-dimensional(2D)topological materials have recently garnered significant interest due to their profound physical properties and promising applications for future quantum nanoelectronics.Achieving various topological states within one type of materials is,however,seldom reported.Based on first-principles calculations and tightbinding models,we investigate topological electronic states in a novel family of 2D halogenated tetragonal stanene(T-SnX,X=F,Cl,Br,I).All the four monolayers are found to be unusual topological nodal-line semimetals(NLSs),protected by a glide mirror symmetry.When spin-orbit coupling(SOC)is turned on,T-SnF and TSnCl are still ascertained as topological NLSs due to the remaining band inversion,primarily composed of Sn pxy orbitals,while T-Sn Br and T-SnI become quantum spin Hall insulators.The phase transition is ascribed to moving up in energy of Sn s orbitals and increasing of SOC strengths.The topology origin in the materials is uniformly rationalized through elementary band representations.The robust and diverse topological states found in the 2D T-SnX monolayers position them as an excellent material platform for development of innovative topological electronics.展开更多
Developing sustainable and clean energy sources(e.g.,solar,wind,and tide energy)is essential to achieve the goal of carbon neutrality.Due to the discontinuous and inco nsistent nature of common clean energy sources,hi...Developing sustainable and clean energy sources(e.g.,solar,wind,and tide energy)is essential to achieve the goal of carbon neutrality.Due to the discontinuous and inco nsistent nature of common clean energy sources,high-performance energy storage technologies are a critical part of achieving this target.Aqueous zinc metal batteries(AZMBs)with inherent safety,low cost,and competitive performance are regarded as one of the promising candidates for grid-scale energy storage.However,zinc metal anodes(ZMAs)with irreversible problems of dendrite growth,hydrogen evolution reaction,self-corrosio n,and other side reactions have seriously hindered the development and commercialization of AZMBs.An increasing number of researchers are focusing on the stability of ZMAs,so assessing the effectiveness of existing research strategies is critical to the development of AZMBs.This review aims to provide a comprehensive overview of the fundamentals and challenges of AZMBs.Resea rch strategies for interfacial modification of ZMAs are systematically presented.The features of artificial interfacial coating and in-situ interfacial coating of ZMAs are compared and discussed in detail,as well as the effect of modified interfacial ZMA on the full-battery performance.Finally,perspectives are provided on the problems and challenges of ZMAs.This review is expected to offer a constructive reference for the further development and commercialization of AZMBs.展开更多
Anthropogenic activities have contributed to pollution of water bodies through deposition of diverse pollutants amongst which are heavy metals. These pollutants, which at times are above the maximum concentration leve...Anthropogenic activities have contributed to pollution of water bodies through deposition of diverse pollutants amongst which are heavy metals. These pollutants, which at times are above the maximum concentration levels recommended, are detrimental to the quality of the water, soil and crops (plant) with subsequent human health risks. The objective of the work was to evaluate the impacts of human-based activities on the heavy metal properties of surface water with focus on the Kumba River basin. Field observations, interviews, field measurements and laboratory analyses of different water samples enabled us to collect the different data. The results show four main human-based activities within the river basin (agriculture, livestock production, domestic waste disposal and carwash activities) that pollute surface water. Approximately 20.61 tons of nitrogen and phosphorus from agricultural activities, 156.48 tons of animal wastes, 2517.5 tons of domestic wastes and 1.52 tons of detergent from carwash activities were deposited into the river each year. A highly significant difference at 1% was observed between the upstream and downstream heavy metal loads in four of the five heavy metals tested except for copper that was not significant. Lead concentrations were highest in all the activities with an average of 2.4 mg∙L<sup>−</sup><sup>1</sup> representing 57.81%, followed by zinc with 1.596 mg∙L<sup>−</sup><sup>1</sup> (38.45%) and manganese with 0.155 mg∙L<sup>−</sup><sup>1</sup> (3.74%) for the different anthropogenic activities thus indicating that these activities highly lead to pollution of the Kumba River water. The level of zinc and manganese was significantly influenced at ρ 005 by anthropogenic activities though generally the variations were in the order: carwash (3.196 mg∙L<sup>−</sup><sup>1</sup>) < domestic waste disposal (3.347 mg∙L<sup>−</sup><sup>1</sup>) < agriculture (4.172 mg∙L<sup>−</sup><sup>1</sup>) < livestock (4.886 mg∙L<sup>−</sup><sup>1</sup>) respectively and leading to a total of 14.04 tons of heavy metal pollutants deposited each day.展开更多
Engineering transition metal compounds(TMCs)catalysts with excellent adsorption-catalytic ability has been one of the most effec-tive strategies to accelerate the redox kinetics of sulfur cathodes.Herein,this review f...Engineering transition metal compounds(TMCs)catalysts with excellent adsorption-catalytic ability has been one of the most effec-tive strategies to accelerate the redox kinetics of sulfur cathodes.Herein,this review focuses on engineering TMCs catalysts by cation doping/anion doping/dual doping,bimetallic/bi-anionic TMCs,and TMCs-based heterostructure composites.It is obvious that introducing cations/anions to TMCs or constructing heterostructure can boost adsorption-catalytic capacity by regulating the electronic structure including energy band,d/p-band center,electron filling,and valence state.Moreover,the elec-tronic structure of doped/dual-ionic TMCs are adjusted by inducing ions with different electronegativity,electron filling,and ion radius,resulting in electron redistribution,bonds reconstruction,induced vacancies due to the electronic interaction and changed crystal structure such as lat-tice spacing and lattice distortion.Different from the aforementioned two strategies,heterostructures are constructed by two types of TMCs with different Fermi energy levels,which causes built-in electric field and electrons transfer through the interface,and induces electron redistribution and arranged local atoms to regulate the electronic structure.Additionally,the lacking studies of the three strategies to comprehensively regulate electronic structure for improving catalytic performance are pointed out.It is believed that this review can guide the design of advanced TMCs catalysts for boosting redox of lithium sulfur batteries.展开更多
Evidence for metallization in dense oxygen has been reported for over 30 years[Desgreniers et al.,J.Phys.Chem.94,1117(1990)]at a now routinely accessible 95 GPa[Shimizu et al.,Nature 393,767(1998)].However,despite the...Evidence for metallization in dense oxygen has been reported for over 30 years[Desgreniers et al.,J.Phys.Chem.94,1117(1990)]at a now routinely accessible 95 GPa[Shimizu et al.,Nature 393,767(1998)].However,despite the longevity of this result and the technological advances since,the nature of the metallic phase remains poorly constrained[Akahama et al.,Phys.Rev.Lett.74,4690(1995);Goncharov et al.,Phys.Rev.B 68,224108(2003);Ma,Phys.Rev.B 76,064101(2007);and Weck et al.,Phys.Rev.Lett.102,255503(2009)].In this work,through Raman spectroscopy,we report the distinct vibrational characteristics of metallicζ-O_(2) from 85 to 225 GPa.In comparison with numerical simulations,wefind reasonable agreement with the candidate structure up to about 150 GPa.At higher pressures,the C2/mstructure is found to be unstable and incompatible with experimental observations.Alternative candidate structures,and Ci,with C2/m C2/conly two molecules in the primitive unit cell,are found to be stable and more compatible with measurements above 175 GPa,indicative of the dissociation of(O_(2))4 units.Further,we report and discuss a strong hysteresis and metastability with the precursory phaseϵ-O_(2).Thesefindings will reinvigorate experimental and theoretical work into the dense oxygen system,which will have importance for oxygen-bearing chemistry,prevalent in the deep Earth,as well as fundamental physics.展开更多
5 different forests of Pinus massoniana, Schima superba, Liquidambar formosana, P. massoniana × S. superba, P. massoniana × L. formosana as the research object were set up to study the Cr, Cu and Zn content ...5 different forests of Pinus massoniana, Schima superba, Liquidambar formosana, P. massoniana × S. superba, P. massoniana × L. formosana as the research object were set up to study the Cr, Cu and Zn content of degraded red soil region in subtropics. The soil heavy metal pollution degree was evaluated by national environmental quality standard (II class). The results showed that three soil metals of P. massoniana × S. superba were the highest, and the soil metals enrichment ability was strong. The order of single factor pollution index of metal elements was Cu (1.38) > Cr (0.81) > Zn (0.42), and moderately pollution, pollution warning and no pollution, respectively. There was no significant correlation between three soil heavy metals and soil total carbon (TC), total nitrogen (TN) and total phosphorus (TP). These results suggested that the accumulation of heavy metal elements was not derived from the parent material of soil. There was a significant positive correlation between the three metal elements which indicated that the sources of the three elements were similar. The structural equation model showed that the direct and indirect effects among the influencing factors ultimately affected the activity of heavy metals by cascade effects.展开更多
Entropy production in quasi-isentropic compression (QIC) is critically important for understanding the properties of materials under extremeconditions. However, the origin and accurate quantification of entropy in thi...Entropy production in quasi-isentropic compression (QIC) is critically important for understanding the properties of materials under extremeconditions. However, the origin and accurate quantification of entropy in this situation remain long-standing challenges. In this work, a framework is established for the quantification of entropy production and partition, and their relation to microstructural change in QIC. Cu50Zr50is taken as a model material, and its compression is simulated by molecular dynamics. On the basis of atomistic simulation-informed physicalproperties and free energy, the thermodynamic path is recovered, and the entropy production and its relation to microstructural change aresuccessfully quantified by the proposed framework. Contrary to intuition, entropy production during QIC of metallic glasses is relativelyinsensitive to the strain rate ˙γ when ˙γ ranges from 7.5 × 10^(8) to 2 × 10^(9)/s, which are values reachable in QIC experiments, with a magnitudeof the order of 10^(−2)kB/atom per GPa. However, when ˙γ is extremely high (>2 × 10^(9)/s), a notable increase in entropy production rate with˙γ is observed. The Taylor–Quinney factor is found to vary with strain but not with strain rate in the simulated regime. It is demonstrated thatentropy production is dominated by the configurational part, compared with the vibrational part. In the rate-insensitive regime, the increase inconfigurational entropy exhibits a linear relation to the Shannon-entropic quantification of microstructural change, and a stretched exponential relation to the Taylor–Quinney factor. The quantification of entropy is expected to provide thermodynamic insights into the fundamentalrelation between microstructure evolution and plastic dissipation.展开更多
In this paper,tannic acid(TA)and Fe~(3+)were added to form a layer of metal-polyphenol network structure on the surface of the nanoparticles which were fabricated by zein and carbon quantum dots(CQDs)encapsulating phl...In this paper,tannic acid(TA)and Fe~(3+)were added to form a layer of metal-polyphenol network structure on the surface of the nanoparticles which were fabricated by zein and carbon quantum dots(CQDs)encapsulating phlorotannins(PTN).pH-Responsive nanoparticles were prepared successfully(zein-PTN-CQDs-Fe-~Ⅲ).Further,the formation of composite nanoparticles was confirmed by a series of characterization methods.The zeta-potential and Fourier transform infrared spectroscopy data proved that electrostatic interaction and hydrogen bonding are dominant forces to form nanoparticles.The encapsulation efficiency(EE)revealed that metal-polyphenol network structure could improve the EE of PTN.Thermogravimetric analysis and differential scanning calorimetry experiment indicated the thermal stability of zein-PTN-CQDs-Fe~Ⅲnanoparticles increased because of metal-polyphenol network structure.The pH-responsive nanoparticles greatly increased the release rate of active substances and achieved targeted release.展开更多
Lithium metal batteries(LMBs) promise energy density over 400 Wh kg^(-1).However,they suffer severe electrochemical performance deterioration at sub-zero temperatures.Such failure behavior highly correlates to inferio...Lithium metal batteries(LMBs) promise energy density over 400 Wh kg^(-1).However,they suffer severe electrochemical performance deterioration at sub-zero temperatures.Such failure behavior highly correlates to inferior lithium metal anode(LMA) compatibility and sluggish Li^(+) desolvation.Here,we demonstrate that cyclopentylmethyl ether(CPME) based diluted high-concentration electrolyte(DHCE)enables-60℃ LMBs operation.By leveraging the loose coordination between Li^(+) and CPME,such developed electrolyte boosts the formation of ion clusters to derive anion-dominant interfacial chemistry for enhancing LMA compatibility and greatly accelerates Li^(+) desolvation kinetics.The resulting electrolyte demonstrates high Coulombic efficiencies(CE),providing over 99.5%,99.1%,98.5% and 95% at 25,-20,-40,and-60℃respectively.The assembled Li-S battery exhibits remarkable cyclic stability in-20,and-40℃ at 0.2 C charging and 0.5 C discharging.Even at-60℃,Li-S cell with this designed electrolyte retains> 70% of the initial capacity over 170 cycles.Besides,lithium metal coin cell and pouch cell with10 mg cm^(-2) high S cathode loading exhibit cycling stability at-20℃.This work offers an opportunity for rational designing electrolytes toward low temperature LMBs.展开更多
The development of a durable metallic coating on diverse substrates is both intriguing and challenging,particularly in the research of metal-conductive materials for applications such as batteries,soft electronics,and...The development of a durable metallic coating on diverse substrates is both intriguing and challenging,particularly in the research of metal-conductive materials for applications such as batteries,soft electronics,and beyond.Herein,by learning from the pencil-writing process,a facile solid-ink rubbing technology(SIR-tech)is invented to address the above challenge.The solid-ink is exampled by rational combination of liquid metal and graphite particles.By harnessing the synergistic effects between rubbing and adhesion,controllable metallic skin is successfully formed onto metals,woods,ceramics,and plastics without limitation in size and shape.Moreover,outperforming pure liquid-metal coating,the composite metallic skin by SIR-tech is very robust due to the self-lamination of graphite nanoplate exfoliated by liquid-metal rubbing.The critical factors controlling the structures-properties of the composite metallic skin have been systematically investigated as well.For applications,the SIR-tech is demonstrated to fabricate high-performance composite current collectors for next-generation batteries without traditional metal foils.Meanwhile,advanced skin-electrodes are further demonstrated for stable triboelectricity generation even under temperature fluctuation from-196 to 120℃.This facile and highly-flexible SIR-tech may work as a powerful platform for the studies on functional coatings by liquid metals and beyond.展开更多
Surface metallization of glass fiber(GF)/polyetheretherketone(PEEK)[GF/PEEK] is conducted by coating copper using electroplating and magnetron sputtering and the properties are determined by X-ray diffraction(XRD), sc...Surface metallization of glass fiber(GF)/polyetheretherketone(PEEK)[GF/PEEK] is conducted by coating copper using electroplating and magnetron sputtering and the properties are determined by X-ray diffraction(XRD), scanning electron microscopy(SEM), and electron backscatter diffraction(EBSD).The coating bonding strength is assessed by pull-out tests and scribing in accordance with GB/T 9286-1998.The results show that the Cu coating with a thickness of 30 μm deposited on GF/PEEK by magnetron sputtering has lower roughness, finer grain size, higher crystallinity, as well as better macroscopic compressive stress,bonding strength, and electrical conductivity than the Cu coating deposited by electroplating.展开更多
The development of rechargeable magnesium(Mg) batteries is of practical significance to upgrade the electric energy storage devices due to exceptional capacity and abundant resources of Mg-metal anode.However,the reve...The development of rechargeable magnesium(Mg) batteries is of practical significance to upgrade the electric energy storage devices due to exceptional capacity and abundant resources of Mg-metal anode.However,the reversible Mg electrochemistry suffers from unsatisfied rate capability and lifespan,mainly caused by non-uniform distribution of electrodeposits.In this work,a fresh design concept of threedimensional carbon cloths scaffolds is proposed to overcome the uncontrollable Mg growth via homogenizing electric field and improving magnesiophilicity.A microscopic smooth and nitrogen-containing defective carbonaceous layer is constructed through a facile pyrolysis of ZIF8 on carbon cloths.As revealed by finite element simulation and DFT calculation results,the smooth surface endows with uniform electric field distribution and simultaneously the nitrogen-doping species enable good magnesiophilicity of scaffolds.The fine and uniform Mg nucleus as well as the inner electrodeposit behavior are also disclosed.As a result,an exceptional cycle life of 500 cycles at 4.0 mA cm^(-2) and 4.0 mA h cm^(-2) is firstly realized to our best knowledge.Besides,the functional scaffolds can be cycled for over 2200 h at 2.0 mA cm^(-2) under a normalized capacity of 5.0 mA h cm^(-2),far exceeding previous results.This work offers an effective approach to enable the full potential of carbon cloths-based scaffolds towards metal storage for next generation battery applications.展开更多
基金support for this research from the Natural Science Foundation of China (U1261110)the Natural Science Foundation of Shanxi Province (20130110422)the Foundation of State Key Laboratory of Coal Combustion (FSKLCC-0914)
文摘The occurrence modes of alkali and alkaline-earth metals(AAEMs) in coal relate to their release behavior and ash formation during combustion. To better understand the transformation of AAEMs,the release behavior of water-soluble,HCl-soluble,HCl-insoluble AAEMs during Shenmu coal(SM coal) oxy-fuel combustion in the presence of SO2 and H2O in a drop-tube reactor was investigated through serial dissolution using H2O and HCl solutions. The results show that the release rates of AAEMs increase with an increase in temperature under the three atmospheres studied. The high release rates of Mg and Ca from SM coal are dependent on the high content of soluble Mg and Ca in SM coal. SO2 inhibits the release rates of AAEMs,while H2O promotes them. The effects of SO2 and H2O on the Na and K species are more evident than those on Mg and Ca species. All three types of AAEMs in coal can volatilize in the gas phase during coal combustion. The W-type AAEMs release excessively,whereas the release rates of I-type AAEMs are relatively lower. Different types of AAEM may interconvert through different pathways under certain conditions. Both SO2 and H2O promote the transformation reactions. The effect of SO2 was related to sulfate formation and the promotion by H2O occurs because of a decrease in the melting point of the solid as well as the reaction of H2O.
基金supported by the Open Foundation of State Key Laboratory of Physical Chemistry of Solid Surfaces, Xiamen University (No.200906)the Natural Science Foundation of Jiangxi Province (No.2010GZH0048)+1 种基金the National Natural Science Foundation of China (No. 21067004)the Young Science Foundation of Jiangxi Province Education Office (No. GJJ10150)
文摘Nano-sized γ-alumina (γ-Al2O3) was first prepared by a precipitation method. Then, active component of cobalt and a series of alkaline- earth metal promoters or nickel (Ni) with different contents were loaded on the γ-Al2O3 support. The catalysts were characterized by N2 adsorption-desorption, X-ray diffraction (XRD) and thermogravimetry analysis (TGA). The activity and selectivity of the catalysts in catalytic partial oxidation (CPO) of methane have been compared with Co/γ-Al2O3, and it is found that the catalytic activity, selectivity, and stability are enhanced by the addition of alkaline-earth metals and nickel. The optimal loadings of strontium (Sr) and Ni were 6 and 4 wt%, respectively. This finding will be helpful in designing the trimetallic Co-Ni-Sr/γ-Al2O3 catalysts with high performance in CPO of methane
基金supported by the Science and Technology Funding Project of Fujian Provincial Department of Transportation(No.201337)
文摘Solvothermal reactions of Ca(NO), Sr(NO)with thiophene-2,5-dicarboxylic in DMF afforded two new inorganic-organic hybrid frameworks, [M(TDC)(DMF)]n(M = Ca(1), Sr(2), TDC = thiophene-2,5-dicarboxylic, DMF = N,N?-dimethylformamide), which have been characterized by single-crystal X-ray diffraction, powder X-ray diffraction, elemental analysis and IR spectra. Both compounds feature three-dimensional(3D) frameworks based on the versatile coordinated modes(μ-η~2:η~2, μ-η~2:η~1, μ-η~2:η~1) of carboxylic groups in tdc ligands. C–H···S hydrogen bonds and C–H···π interactions contribute to the stabilization of the structures. They exhibit weaker packing force compared with their literature isomers. Consequently, blue and blue/green luminescence of two compounds has been observed. Their luminescence mechanism can be ascribed to ligand-to-metal charge transfer(LMCT) compared with the ligand-centered luminescence in their isomers. Electronic structural calculations illustrate that under the condition of weaker packing forces, larger gaps can be achieved, which facilitate the LMCT. This work suggests that the introduction of S-heteroatom can result in more electrons rich in the metal centers, thus giving rise to metal-involved luminescence.
基金supported by Key Research and Development Program of Ministry of Science and Technology of the People’s Republic of China (MOST) (No. 2017YFE0131200) for collaboration between China and PolandNational Nature Science Foundation of China (NSFC) (Nos. 22072095, U1908204, 21761162016)+3 种基金General Projects of Liaoning Province Natural Fund (No. 2019-MS-284)National Engineering Laboratory for Mobile Source Emission Control Technology (No. NELMS2018A04)University level innovation team of Shenyang Normal University, Major Incubation Program of Shenyang Normal University (No. ZD201901)supported by the Research Grants Council (RGC) of Hong Kong through NSFC/RGC Joint Research Scheme (No. N_CUHK451/17)。
文摘The performance of catalysts used in after-treatment systems is the key factor for the removal of diesel soot,which is an important component of atmosphericfine particle emissions.Herein,three-dimensionally ordered macroporous–mesoporous Ti_(x)Si+(1-x)O_(2)(3DOM-m Ti_(x)Si+(1-x)O_(2)) and its supported MnO_(x)catalysts doped with different alkali/alkaline-earth metals (AMnO_(x)/3 DOM-m Ti_(0.7)Si_(0.3)O_(2)(A:Li,Na,K,Ru,Cs,Mg,Ca,Sr,Ba)) were prepared by mesoporous template (P123)-assisted colloidal crystal template (CCT) and incipient wetness impregnation methods,respectively.Physicochemical characterizations of the catalysts were performed using scanning electron microscopy,X-ray diffraction,N_(2)adsorption–desorption,H_(2)temperature-programmed reduction,O_(2)temperature-programmed desorption,NO temperature-programmed oxidation,and Raman spectroscopy techniques;then,we evaluated their catalytic performances for the removal of diesel soot particles.The results show that the 3DOM-m Ti_(0.7)Si_(0.3)O_(2)supports exhibited a well-defined 3DOM-m nanostructure,and AMnO_(x)nanoparticles with 10–50 nm were evenly dispersed on the inner walls of the uniform macropores.In addition,the as-prepared catalysts exhibited good catalytic performance for soot combustion.Among the prepared catalysts,CsMnO_(x)/3DOM-m Ti_(0.7)Si_(0.3)O_(2)had the highest catalytic activity for soot combustion,with T10,T50,and T90(the temperatures corresponding to soot conversion rates of 10%,50%,and 90%) values of 285,355,and 393℃,respectively.The high catalytic activity of the CsMnO_(x)/3 DOM-m Ti_(0.7)Si_(0.3)O_(2)catalysts was attributed to their excellent low-temperature reducibility and homogeneous macroporous–mesoporous structure,as well as to the synergistic effects between Cs and Mn species and between CsMnO_(x)and the Ti_(0.7)Si_(0.3)O_(2)support.
基金the support from the CIPHER Project(IIID 2018-008)funded by the Commission on Higher Education-Philippine California Advanced Research Institutes(CHED-PCARI)。
文摘Transition metal phosphides(TMPs)have been regarded as alternative hydrogen evolution reaction(HER)and oxygen evolution reaction(OER)catalysts owing to their comparable activity to those of noble metal-based catalysts.TMPs have been produced in various morphologies,including hollow and porous nanostructures,which are features deemed desirable for electrocatalytic materials.Templated synthesis routes are often responsible for such morphologies.This paper reviews the latest advances and existing challenges in the synthesis of TMP-based OER and HER catalysts through templated methods.A comprehensive review of the structure-property-performance of TMP-based HER and OER catalysts prepared using different templates is presented.The discussion proceeds according to application,first by HER and further divided among the types of templates used-from hard templates,sacrificial templates,and soft templates to the emerging dynamic hydrogen bubble template.OER catalysts are then reviewed and grouped according to their morphology.Finally,prospective research directions for the synthesis of hollow and porous TMP-based catalysts,such as improvements on both activity and stability of TMPs,design of environmentally benign templates and processes,and analysis of the reaction mechanism through advanced material characterization techniques and theoretical calculations,are suggested.
基金supported by the Basic Science Research Program through the National Research Foundation of Korea(NRF)grant funded by the Korean government(MSIT)(2021R1A4A2000934).
文摘The metal-organic framework(MOF)derived Ni–Co–C–N composite alloys(NiCCZ)were“embedded”inside the carbon cloth(CC)strands as opposed to the popular idea of growing them upward to realize ultrastable energy storage and conversion application.The NiCCZ was then oxygen functionalized,facilitating the next step of stoichiometric sulfur anion diffusion during hydrothermal sulfurization,generating a flower-like metal hydroxysulfide structure(NiCCZOS)with strong partial implantation inside CC.Thus obtained NiCCZOS shows an excellent capacity when tested as a supercapacitor electrode in a three-electrode configuration.Moreover,when paired with the biomass-derived nitrogen-rich activated carbon,the asymmetric supercapacitor device shows almost 100%capacity retention even after 45,000 charge–discharge cycles with remarkable energy density(59.4 Wh kg^(-1)/263.8μWh cm^(–2))owing to a uniquely designed cathode.Furthermore,the same electrode performed as an excellent bifunctional water-splitting electrocatalyst with an overpotential of 271 mV for oxygen evolution reaction(OER)and 168.4 mV for hydrogen evolution reaction(HER)at 10 mA cm−2 current density along with 30 h of unhinged chronopotentiometric stability performance for both HER and OER.Hence,a unique metal chalcogenide composite electrode/substrate configuration has been proposed as a highly stable electrode material for flexible energy storage and conversion applications.
基金supported by the National Key Research and Development Programs(2021YFB2400400)Major Science and Technology Innovation Project of Hunan Province(2020GK10102020GK1014-4)+7 种基金National Natural Science Foundation of China(32201162)the 70th general grant of China Postdoctoral Science Foundation(2021M702947)Natural Science Foundation of Henan(232300420404)Key Scientific and Technological Project of Henan Province(232102320290,232102311156)Key Research Project Plan for Higher Education Institutions in Henan Province(24A150009,23B430011)Doctor Foundation of Henan University of Engineering(D2022002)the Science and Technology Innovation Program of Hunan Province(2023RC3154)the scientific research projects of Education Department of Hunan Province(23A0188)。
文摘Aqueous Zn metal batteries(AZMBs)with intrinsic safety,high energy density and low cost have been regarded as promising electrochemical energy storage devices.However,the parasitic reaction on metallic Zn anode and the incompatibility between electrode and electrolytes lead to the deterioration of electrochemical performance of AZMBs during the cycling.The critical point to achieve the stable cycling of AZMBs is to properly regulate the zinc ion solvated structure and transfer behavior between metallic Zn anode and electrolyte.In recent years,numerous achievements have been made to resolve the formation of Zn dendrite and interface incompatible issues faced by AZMBs via optimizing the sheath structure and transport capability of zinc ions at electrode-electrolyte interface.In this review,the challenges for metallic Zn anode and electrode-electrolyte interface in AZMBs including dendrite formation and interface characteristics are presented.Following the influences of different strategies involving designing advanced electrode structu re,artificial solid electrolyte interphase(SEI)on Zn anode and electrolyte engineering to regulate zinc ion solvated sheath structure and transport behavior are summarized and discussed.Finally,the perspectives for the future development of design strategies for dendrite-free Zn metal anode and long lifespan AZMBs are also given.
基金This work is supported by the Technologies R&D Program of Huzhou City(No.2022JB01)the Key Research and Development Program of Zhejiang Province(No.2023C01127)the Highstar Corporation HSD20210118.
文摘The widespread adoption of lithium-ion batteries has been driven by the proliferation of portable electronic devices and electric vehicles,which have increasingly stringent energy density requirements.Lithium metal batteries(LMBs),with their ultralow reduction potential and high theoretical capacity,are widely regarded as the most promising technical pathway for achieving high energy density batteries.In this review,we provide a comprehensive overview of fundamental issues related to high reactivity and migrated interfaces in LMBs.Furthermore,we propose improved strategies involving interface engineering,3D current collector design,electrolyte optimization,separator modification,application of alloyed anodes,and external field regulation to address these challenges.The utilization of solid-state electrolytes can significantly enhance the safety of LMBs and represents the only viable approach for advancing them.This review also encompasses the variation in fundamental issues and design strategies for the transition from liquid to solid electrolytes.Particularly noteworthy is that the introduction of SSEs will exacerbate differences in electrochemical and mechanical properties at the interface,leading to increased interface inhomogeneity—a critical factor contributing to failure in all-solidstate lithium metal batteries.Based on recent research works,this perspective highlights the current status of research on developing high-performance LMBs.
基金supported by the National Natural Science Foundation of China(Grant Nos.12174059,11874117,11904101,and 11604134)the Natural Science Foundation of Shanghai(Grant No.21ZR140820)。
文摘Two-dimensional(2D)topological materials have recently garnered significant interest due to their profound physical properties and promising applications for future quantum nanoelectronics.Achieving various topological states within one type of materials is,however,seldom reported.Based on first-principles calculations and tightbinding models,we investigate topological electronic states in a novel family of 2D halogenated tetragonal stanene(T-SnX,X=F,Cl,Br,I).All the four monolayers are found to be unusual topological nodal-line semimetals(NLSs),protected by a glide mirror symmetry.When spin-orbit coupling(SOC)is turned on,T-SnF and TSnCl are still ascertained as topological NLSs due to the remaining band inversion,primarily composed of Sn pxy orbitals,while T-Sn Br and T-SnI become quantum spin Hall insulators.The phase transition is ascribed to moving up in energy of Sn s orbitals and increasing of SOC strengths.The topology origin in the materials is uniformly rationalized through elementary band representations.The robust and diverse topological states found in the 2D T-SnX monolayers position them as an excellent material platform for development of innovative topological electronics.
基金the financial support from the Australian Research Council,Centre for Materials Science,Queensland University of Technologythe Supported by the Fundamental Research Funds for the Central Universities。
文摘Developing sustainable and clean energy sources(e.g.,solar,wind,and tide energy)is essential to achieve the goal of carbon neutrality.Due to the discontinuous and inco nsistent nature of common clean energy sources,high-performance energy storage technologies are a critical part of achieving this target.Aqueous zinc metal batteries(AZMBs)with inherent safety,low cost,and competitive performance are regarded as one of the promising candidates for grid-scale energy storage.However,zinc metal anodes(ZMAs)with irreversible problems of dendrite growth,hydrogen evolution reaction,self-corrosio n,and other side reactions have seriously hindered the development and commercialization of AZMBs.An increasing number of researchers are focusing on the stability of ZMAs,so assessing the effectiveness of existing research strategies is critical to the development of AZMBs.This review aims to provide a comprehensive overview of the fundamentals and challenges of AZMBs.Resea rch strategies for interfacial modification of ZMAs are systematically presented.The features of artificial interfacial coating and in-situ interfacial coating of ZMAs are compared and discussed in detail,as well as the effect of modified interfacial ZMA on the full-battery performance.Finally,perspectives are provided on the problems and challenges of ZMAs.This review is expected to offer a constructive reference for the further development and commercialization of AZMBs.
文摘Anthropogenic activities have contributed to pollution of water bodies through deposition of diverse pollutants amongst which are heavy metals. These pollutants, which at times are above the maximum concentration levels recommended, are detrimental to the quality of the water, soil and crops (plant) with subsequent human health risks. The objective of the work was to evaluate the impacts of human-based activities on the heavy metal properties of surface water with focus on the Kumba River basin. Field observations, interviews, field measurements and laboratory analyses of different water samples enabled us to collect the different data. The results show four main human-based activities within the river basin (agriculture, livestock production, domestic waste disposal and carwash activities) that pollute surface water. Approximately 20.61 tons of nitrogen and phosphorus from agricultural activities, 156.48 tons of animal wastes, 2517.5 tons of domestic wastes and 1.52 tons of detergent from carwash activities were deposited into the river each year. A highly significant difference at 1% was observed between the upstream and downstream heavy metal loads in four of the five heavy metals tested except for copper that was not significant. Lead concentrations were highest in all the activities with an average of 2.4 mg∙L<sup>−</sup><sup>1</sup> representing 57.81%, followed by zinc with 1.596 mg∙L<sup>−</sup><sup>1</sup> (38.45%) and manganese with 0.155 mg∙L<sup>−</sup><sup>1</sup> (3.74%) for the different anthropogenic activities thus indicating that these activities highly lead to pollution of the Kumba River water. The level of zinc and manganese was significantly influenced at ρ 005 by anthropogenic activities though generally the variations were in the order: carwash (3.196 mg∙L<sup>−</sup><sup>1</sup>) < domestic waste disposal (3.347 mg∙L<sup>−</sup><sup>1</sup>) < agriculture (4.172 mg∙L<sup>−</sup><sup>1</sup>) < livestock (4.886 mg∙L<sup>−</sup><sup>1</sup>) respectively and leading to a total of 14.04 tons of heavy metal pollutants deposited each day.
基金The authors acknowledge funding from National Natural Science Foundation of China(52302307)Shaanxi Province(2023-ZDLGY-24,2023-JC-QN-0473)+2 种基金project funded by China Postdoctoral Science Foundation(2023MD734210)the Open Foundation of State Key Laboratory for Advanced Metals and Materials(2022-Z01)Shaanxi Provincial Department of Education industrialization project(21JC018).
文摘Engineering transition metal compounds(TMCs)catalysts with excellent adsorption-catalytic ability has been one of the most effec-tive strategies to accelerate the redox kinetics of sulfur cathodes.Herein,this review focuses on engineering TMCs catalysts by cation doping/anion doping/dual doping,bimetallic/bi-anionic TMCs,and TMCs-based heterostructure composites.It is obvious that introducing cations/anions to TMCs or constructing heterostructure can boost adsorption-catalytic capacity by regulating the electronic structure including energy band,d/p-band center,electron filling,and valence state.Moreover,the elec-tronic structure of doped/dual-ionic TMCs are adjusted by inducing ions with different electronegativity,electron filling,and ion radius,resulting in electron redistribution,bonds reconstruction,induced vacancies due to the electronic interaction and changed crystal structure such as lat-tice spacing and lattice distortion.Different from the aforementioned two strategies,heterostructures are constructed by two types of TMCs with different Fermi energy levels,which causes built-in electric field and electrons transfer through the interface,and induces electron redistribution and arranged local atoms to regulate the electronic structure.Additionally,the lacking studies of the three strategies to comprehensively regulate electronic structure for improving catalytic performance are pointed out.It is believed that this review can guide the design of advanced TMCs catalysts for boosting redox of lithium sulfur batteries.
基金The computational resources were provided by the Cambridge Tier-2 sys-tem operated by the University of Cambridge Research Computing Service and funded by the UK EPSRC(Grant No.EP/P020259/1).
文摘Evidence for metallization in dense oxygen has been reported for over 30 years[Desgreniers et al.,J.Phys.Chem.94,1117(1990)]at a now routinely accessible 95 GPa[Shimizu et al.,Nature 393,767(1998)].However,despite the longevity of this result and the technological advances since,the nature of the metallic phase remains poorly constrained[Akahama et al.,Phys.Rev.Lett.74,4690(1995);Goncharov et al.,Phys.Rev.B 68,224108(2003);Ma,Phys.Rev.B 76,064101(2007);and Weck et al.,Phys.Rev.Lett.102,255503(2009)].In this work,through Raman spectroscopy,we report the distinct vibrational characteristics of metallicζ-O_(2) from 85 to 225 GPa.In comparison with numerical simulations,wefind reasonable agreement with the candidate structure up to about 150 GPa.At higher pressures,the C2/mstructure is found to be unstable and incompatible with experimental observations.Alternative candidate structures,and Ci,with C2/m C2/conly two molecules in the primitive unit cell,are found to be stable and more compatible with measurements above 175 GPa,indicative of the dissociation of(O_(2))4 units.Further,we report and discuss a strong hysteresis and metastability with the precursory phaseϵ-O_(2).Thesefindings will reinvigorate experimental and theoretical work into the dense oxygen system,which will have importance for oxygen-bearing chemistry,prevalent in the deep Earth,as well as fundamental physics.
文摘5 different forests of Pinus massoniana, Schima superba, Liquidambar formosana, P. massoniana × S. superba, P. massoniana × L. formosana as the research object were set up to study the Cr, Cu and Zn content of degraded red soil region in subtropics. The soil heavy metal pollution degree was evaluated by national environmental quality standard (II class). The results showed that three soil metals of P. massoniana × S. superba were the highest, and the soil metals enrichment ability was strong. The order of single factor pollution index of metal elements was Cu (1.38) > Cr (0.81) > Zn (0.42), and moderately pollution, pollution warning and no pollution, respectively. There was no significant correlation between three soil heavy metals and soil total carbon (TC), total nitrogen (TN) and total phosphorus (TP). These results suggested that the accumulation of heavy metal elements was not derived from the parent material of soil. There was a significant positive correlation between the three metal elements which indicated that the sources of the three elements were similar. The structural equation model showed that the direct and indirect effects among the influencing factors ultimately affected the activity of heavy metals by cascade effects.
基金supported by the NSAF under Grant No.U1830206,the National Key R&D Program of China under Grant No.2017YFA0403200the National Natural Science Foundation of China under Grant Nos.11874424 and 12104507the Science and Technology Innovation Program of Hunan Province under Grant No.2021RC4026.
文摘Entropy production in quasi-isentropic compression (QIC) is critically important for understanding the properties of materials under extremeconditions. However, the origin and accurate quantification of entropy in this situation remain long-standing challenges. In this work, a framework is established for the quantification of entropy production and partition, and their relation to microstructural change in QIC. Cu50Zr50is taken as a model material, and its compression is simulated by molecular dynamics. On the basis of atomistic simulation-informed physicalproperties and free energy, the thermodynamic path is recovered, and the entropy production and its relation to microstructural change aresuccessfully quantified by the proposed framework. Contrary to intuition, entropy production during QIC of metallic glasses is relativelyinsensitive to the strain rate ˙γ when ˙γ ranges from 7.5 × 10^(8) to 2 × 10^(9)/s, which are values reachable in QIC experiments, with a magnitudeof the order of 10^(−2)kB/atom per GPa. However, when ˙γ is extremely high (>2 × 10^(9)/s), a notable increase in entropy production rate with˙γ is observed. The Taylor–Quinney factor is found to vary with strain but not with strain rate in the simulated regime. It is demonstrated thatentropy production is dominated by the configurational part, compared with the vibrational part. In the rate-insensitive regime, the increase inconfigurational entropy exhibits a linear relation to the Shannon-entropic quantification of microstructural change, and a stretched exponential relation to the Taylor–Quinney factor. The quantification of entropy is expected to provide thermodynamic insights into the fundamentalrelation between microstructure evolution and plastic dissipation.
基金supported by the National Key R&D Program of China (2018YFD0901106)the Wenzhou Major Science and Technology Project (ZN2021002)the Ningbo“3315 series program”for high-level talents (2020B-34-G)。
文摘In this paper,tannic acid(TA)and Fe~(3+)were added to form a layer of metal-polyphenol network structure on the surface of the nanoparticles which were fabricated by zein and carbon quantum dots(CQDs)encapsulating phlorotannins(PTN).pH-Responsive nanoparticles were prepared successfully(zein-PTN-CQDs-Fe-~Ⅲ).Further,the formation of composite nanoparticles was confirmed by a series of characterization methods.The zeta-potential and Fourier transform infrared spectroscopy data proved that electrostatic interaction and hydrogen bonding are dominant forces to form nanoparticles.The encapsulation efficiency(EE)revealed that metal-polyphenol network structure could improve the EE of PTN.Thermogravimetric analysis and differential scanning calorimetry experiment indicated the thermal stability of zein-PTN-CQDs-Fe~Ⅲnanoparticles increased because of metal-polyphenol network structure.The pH-responsive nanoparticles greatly increased the release rate of active substances and achieved targeted release.
基金supported by the National Natural Science Foundation of China(Nos.21975087,22008082)。
文摘Lithium metal batteries(LMBs) promise energy density over 400 Wh kg^(-1).However,they suffer severe electrochemical performance deterioration at sub-zero temperatures.Such failure behavior highly correlates to inferior lithium metal anode(LMA) compatibility and sluggish Li^(+) desolvation.Here,we demonstrate that cyclopentylmethyl ether(CPME) based diluted high-concentration electrolyte(DHCE)enables-60℃ LMBs operation.By leveraging the loose coordination between Li^(+) and CPME,such developed electrolyte boosts the formation of ion clusters to derive anion-dominant interfacial chemistry for enhancing LMA compatibility and greatly accelerates Li^(+) desolvation kinetics.The resulting electrolyte demonstrates high Coulombic efficiencies(CE),providing over 99.5%,99.1%,98.5% and 95% at 25,-20,-40,and-60℃respectively.The assembled Li-S battery exhibits remarkable cyclic stability in-20,and-40℃ at 0.2 C charging and 0.5 C discharging.Even at-60℃,Li-S cell with this designed electrolyte retains> 70% of the initial capacity over 170 cycles.Besides,lithium metal coin cell and pouch cell with10 mg cm^(-2) high S cathode loading exhibit cycling stability at-20℃.This work offers an opportunity for rational designing electrolytes toward low temperature LMBs.
基金the financial support from the National Natural Science Foundation of China (52125301 and 52203123)the Fundamental Research Funds for the Central Universitiespartially sponsored by the Double First-Class Construction Funds of Sichuan University。
文摘The development of a durable metallic coating on diverse substrates is both intriguing and challenging,particularly in the research of metal-conductive materials for applications such as batteries,soft electronics,and beyond.Herein,by learning from the pencil-writing process,a facile solid-ink rubbing technology(SIR-tech)is invented to address the above challenge.The solid-ink is exampled by rational combination of liquid metal and graphite particles.By harnessing the synergistic effects between rubbing and adhesion,controllable metallic skin is successfully formed onto metals,woods,ceramics,and plastics without limitation in size and shape.Moreover,outperforming pure liquid-metal coating,the composite metallic skin by SIR-tech is very robust due to the self-lamination of graphite nanoplate exfoliated by liquid-metal rubbing.The critical factors controlling the structures-properties of the composite metallic skin have been systematically investigated as well.For applications,the SIR-tech is demonstrated to fabricate high-performance composite current collectors for next-generation batteries without traditional metal foils.Meanwhile,advanced skin-electrodes are further demonstrated for stable triboelectricity generation even under temperature fluctuation from-196 to 120℃.This facile and highly-flexible SIR-tech may work as a powerful platform for the studies on functional coatings by liquid metals and beyond.
基金Funded by Shenzhen-Hong Kong Innovative Collaborative Research and Development Program (Nos.SGLH20181109 110802117, CityU 9240014)Innovation Project of Southwestern Institute of Physics (Nos.202001XWCXYD002, 202301XWCX003)CNNC Young Talent Program (No.2023JZYF-01)。
文摘Surface metallization of glass fiber(GF)/polyetheretherketone(PEEK)[GF/PEEK] is conducted by coating copper using electroplating and magnetron sputtering and the properties are determined by X-ray diffraction(XRD), scanning electron microscopy(SEM), and electron backscatter diffraction(EBSD).The coating bonding strength is assessed by pull-out tests and scribing in accordance with GB/T 9286-1998.The results show that the Cu coating with a thickness of 30 μm deposited on GF/PEEK by magnetron sputtering has lower roughness, finer grain size, higher crystallinity, as well as better macroscopic compressive stress,bonding strength, and electrical conductivity than the Cu coating deposited by electroplating.
基金supported by the National Natural Science Foundation of China(51972187,22279068,52374306)the Natural Science Foundation of Shandong Province(ZR2021QE166)Qingdao New Energy Shandong Laboratory Open Project(QNESL OP202312)。
文摘The development of rechargeable magnesium(Mg) batteries is of practical significance to upgrade the electric energy storage devices due to exceptional capacity and abundant resources of Mg-metal anode.However,the reversible Mg electrochemistry suffers from unsatisfied rate capability and lifespan,mainly caused by non-uniform distribution of electrodeposits.In this work,a fresh design concept of threedimensional carbon cloths scaffolds is proposed to overcome the uncontrollable Mg growth via homogenizing electric field and improving magnesiophilicity.A microscopic smooth and nitrogen-containing defective carbonaceous layer is constructed through a facile pyrolysis of ZIF8 on carbon cloths.As revealed by finite element simulation and DFT calculation results,the smooth surface endows with uniform electric field distribution and simultaneously the nitrogen-doping species enable good magnesiophilicity of scaffolds.The fine and uniform Mg nucleus as well as the inner electrodeposit behavior are also disclosed.As a result,an exceptional cycle life of 500 cycles at 4.0 mA cm^(-2) and 4.0 mA h cm^(-2) is firstly realized to our best knowledge.Besides,the functional scaffolds can be cycled for over 2200 h at 2.0 mA cm^(-2) under a normalized capacity of 5.0 mA h cm^(-2),far exceeding previous results.This work offers an effective approach to enable the full potential of carbon cloths-based scaffolds towards metal storage for next generation battery applications.