Ultrahigh strength and improved electrical conductivity in an aging strengthened copper alloy processed by combination of equal channel angular pressing and thermomechanical treatment

In this paper,equal channel angular pressing and thermomechanical treatment was employed to improve the strength and electrical conductivity of an aging strengthened Cu-Ti-Cr-Mg alloy,and the microstructure and properties of the alloy were investigated in detail.The results showed that the samples deformed by the combination of cryogenic equal channel angular pressing(ECAP)and rolling had good comprehensive properties after aging at 400℃.The tensile strength of the peak-aged and over-aged samples was 1120 MPa and 940 MPa,with their corresponding electrical conductivity of 14.7%IACS and 22.1%IACS,respectively.ECAP and cryogenic rolling introduced high density dislocations,leading to the inhibition of the softening effects and refinement of the grains.After a long time aging at 400℃,the alloy exhibited ultra-high strength with obvious increasing electrical conductivity.The high strength was attributed to the synergistic effect of work hardening,grain refinement strengthening and precipitation strengthening.The precipitation of a large amount of Ti atoms from the matrix led to the high electrical conductivity of the over-aged sample.

Solid state recycling of Mg-Gd-Y-Zn-Zr alloy chips by isothermal sintering and equal channel angular pressing

The Mg-7Gd-4Y-2Zn-0.5Zr alloy chips were successfully recycled through isothermal sintering and equal channel angular pressing(ECAP).The mechanical properties and microstructure evolution of samples during the recycling process were studied in detail.The eutectic phases in the as-cast alloy transform into long period-stacking ordered(LPSO)phases after homogenization,which can improve the plasticity of the material.After isothermal sintering,the density of the sample is lower than that of the homogenized sample,and oxide films are formed adjacent to the bonding interface of the metal chips.Hence,the plasticity of the sintered sample is poor.Dense samples are fabricated after ECAP.Although the grains are not refined compared to the sintered sample,the microstructure becomes more uniform due to recrystallization.Fiber interdendritic LPSO phase and kinked 14H-LPSO phase are formed in the alloy due to the shear deformation during the ECAP process,which improves the strength and plasticity of the sample significantly.Furthermore,the basal texture is weakened due to the Bc route of the ECAP process,which can increase the Schmid factor of the basal slip system and improve the elongation of the sample.After 2 ECAP passes,the fully densified recycled billet shows superior mechanical properties with an ultimate tensile strength of 307.1 MPa and elongation of 11.1%.

On the Equality of Weighted BajratarevićMeans to Quasi-Arithmetic Means

In this paper, we considered the equality problem of weighted Bajraktarević means with weighted quasi-arithmetic means. Using the method of substituting for functions, we first transform the equality problem into solving an equivalent functional equation. We obtain the necessary and sufficient conditions for the equality equation.

Simple shear extrusion versus equal channel angular pressing:A comparative study on the microstructure and mechanical properties of an Mg alloy

Two severe plastic deformation(SPD)techniques of simple shear extrusion(SSE)and equal channel angular pressing(ECAP)were employed to process an extruded Mg-6Gd-3Y-1.5Ag(wt%)alloy at 553 K for 1,2,4 and 6 passes.The microstructural evolutions were studied by electron back scattered diffraction(EBSD)analysis and transmission electron microscopy(TEM).The initial grain size of 7.5μm in the extruded alloy was reduced to about 1.3μm after 6 SPD passes.Discontinuous dynamic recrystallization was suggested to be operative in both SSE and ECAP,with also a potential contribution of continuous dynamic recrystallization at the early stages of deformation.The difference in the shear strain paths of the two SPD techniques caused different progression rate of dynamic recrystallization(DRX),so that the alloys processed by ECAP exhibited higher fractions of recrystallization and high angle grain boundaries(HAGBs).It was revealed that crystallographic texture was also significantly influenced by the difference in the strain paths of the two SPD methods,where dissimilar basal plane texture components were obtained.The compression tests,performed along extrusion direction(ED),indicated that the compressive yield stress(CYS)and ultimate compressive strength(UCS)of the alloys after both SEE and ECAP augmented continuously by increasing the number of passes.ECAP-processed alloys had lower values of CYS and UCS compared to their counterparts processed by SSE.This difference in the mechanical responses was attributed to the different configurations of basal planes with respect to the loading direction(ED)of each SPD technique.

Superplastic behavior of a fine-grained Mg-Gd-Y-Ag alloy processed by equal channel angular pressing

An extruded Mg-6Gd-3Y-1.5Ag(wt%) alloy was processed by 6 passes of equal channel angular pressing(ECAP) at 553 K using route Bc to refine the microstructure. Electron back-scattered diffraction(EBSD) analysis showed a fully recrystallized microstructure for the extruded alloy with a mean grain size of 8.6 μm. The microstructure of the ECAP-processed alloy was uniformly refined through dynamic recrystallization(DRX). This microstructure contained fine grains with an average size of 1.3 μm, a high fraction of high angle grain boundaries(HAGBs), and nano-sized Mg_(5)Gd-type particles at the boundaries of the DRXed grains, detected by transmission electron microscopy(TEM). High-temperature shear punch testing(SPT) was used to evaluate the superplastic behavior of both the extruded and ECAP-processed alloys by measuring the strain rate sensitivity(SRS) index(m-value). While the highest m-value for the extruded alloy was measured to be 0.24 at 673 K, the ECAP-processed alloy exhibited much higher m-values of 0.41 and 0.52 at 598 and 623 K, respectively,delineating the occurrence of superplastic flow. Based on the calculated average activation energy of 118 kJ mol^(-1) and m-values close to 0.5, the deformation mechanism for superplastic flow at the temperatures of 598 and 623 K for the ECAP-processed alloys was recognized to be grain boundary sliding(GBS) assisted by grain boundary diffusion.

Microstructure and mechanical properties of ZE10 magnesium alloy prepared by equal channel angular pressing

ZE10 magnesium alloy was subjected to equal-channel angular pressing （ECAP） up to 12 passes in a die with an angle of 120° between the two channels at 250-300℃. An inhomogeneous microstructure of bimodal grains including fine grains of 1-2 μm as well as coarse grains of about 20μm was obtained after the initial 1-4 ECAP passes. The grain size became increasingly homogeneous with further ECAP processing and the grains were significantly refined to 1-2 ktm after 8 passes and further refined to 0.5-1 μm after 12 passes. The alloy＇s yield strength changed slightly but the ductility improved greatly initially up to 4-6 passes corresponding to the bimodal grain microstructure. And after the subsequent pressing of more than 8 passes, the tensile strength including yield strength improved while the elongation decreased gradually.

Microstructure and mechanical property of a high-strength Mg-10Gd-6Y-1.5Zn-0.5Zr alloy prepared by multi-pass equal channel angular pressing

In this work,a high-strength Mg–10Gd–6Y–1.5Zn–0.5Zr(wt.%)alloy was fabricated by successive multi-pass equal channel angular pressing(ECAP).The microstructure and mechanical property of as-cast and ECAP alloys were systematically researched by X-ray diffractometer,scanning electron microscopy,transmission electron microscopy and compression test.The results show that the microstructure of as-cast alloy consists ofα-Mg grains,Mg24Y5 networks,18R blocks,fine 14H lamellas,and fewY-rich particles.After 8 passes ECAP,dynamic recrystallization ofα-Mg is developed and their average grain size decreases to about 1μm.The network Mg_(24)Y_(5) phase at grain boundaries is broken into small particles with average diameter lower than 0.5μm.Moreover,18R blocks are kinked and delaminated,or broken into small particles and blended with Mg24Y5 particles.14H lamellas grow gradually or are dynamically precipitated within certainα-Mg grains.Compression tests indicate that 8p ECAP alloy exhibits excellent mechanical property with compressive strength of 537 MPa and fracture strain of 17.0%.The significant improvement for both strength and ductility of deformed alloy could be ascribed to DRX grains,refined Mg24Y5 particles,18R kinking and dynamical precipitation of 14H.

Assessing the Spatial Equality of COVID Testing Sites Maintaining Zero COVID Policy

Rapid and timely testing is essential to minimize the COVID-19 spread. Decision makers and policy planners need to determine the equal distribution and accessibility of testing sites. This study mainly examines the spatial equality of COVID-19 testing sites that maintain a zero COVID policy in Guangzhou City. The study has identified the spatial disparities of COVID testing sites, characteristics of testing locations, and accessibility. The study has obtained information on COVID testing sites in Guangzhou City and population data. Point pattern analyses, Euclidian distance and allocation, and network analyses are the main methods used to achieve the research objectives, and 1183 total COVID testing sites can be recognized in Guangzhou City. Results revealed that spatial disparities could be noticed over the study area. Testing locations of Guangzhou City are highly clustered. The most significant testing sites are located in Haizhu District, which has the third largest population. The highest population density can be identified in Yuexiu District. However, only 94 testing sites are located there. According to all the results, higher disparities can be identified, and a lack of testing sites is located in the north part of the study area. Some people in the northern part have to travel more than 10 km to reach a testing site. Finally, this paper suggests increasing the number of testing sites in the north and south parts of the study area and keeping the same distribution, considering the area, total population, and population density. This kind of research will be helpful to decision-makers in making proper decisions to maintain a zero COVID policy.

On Performance Characteristics of a Nonparametric Subset Selection Procedure with a Small Randomized Block Experimental Design

This article addresses the issue of computing the constant required to implement a specific nonparametric subset selection procedure based on ranks of data arising in a statistical randomized block experimental design. A model of three populations and two blocks is used to compute the probability distribution of the relevant statistic, the maximum of the population rank sums minus the rank sum of the “best” population. Calculations are done for populations following a normal distribution, and for populations following a bi-uniform distribution. The least favorable configuration in these cases is shown to arise when all three populations follow identical distributions. The bi-uniform distribution leads to an asymptotic counterexample to the conjecture that the least favorable configuration, i.e., that configuration minimizing the probability of a correct selection, occurs when all populations are identically distributed. These results are consistent with other large-scale simulation studies. All relevant computational R-codes are provided in appendices.

A New Equalization Method for Lithium-Ion Battery Packs Based on CUK

Aiming at the traditional CUK equalizer can only perform energy equalization between adjacent batteries,if the two single batteries that need to be equalized are far away from each other,there will be the problem of longer energy transmission path and lower equalization efficiency,this paper optimizes the CUK equalizer and optimizes its peripheral selection circuit,which can support the equalization of single batteries at any two positions.The control strategy adopts the open-circuit voltage(OVC)of the battery and the state of charge(SOC)of the battery as the equalization variables,and selects the corresponding equalization variables according to the energy conditions of the two batteries that need to be equalized,and generates the adaptive equalization current with an adaptive PID controller in order to improve the equalization efficiency.Simulation modeling is performed in Matlab/Simulink 2021b,and the experimental results show that the optimized CUK equalizer in this paper improves the equalization time by 25.58%compared with the traditional CUK equalizer.In addition,compared with the mean value difference(MVD)method,the adaptive PID method reduces the equalization time by about 30%in the static and charging and discharging experimental environments,which verifies the superiority of this equalization scheme.

Equalization Reconstruction Algorithm Based on Reference Signal Frequency Domain Block Joint for DTMB-Based Passive Radar

Channel equalization plays a pivotal role within the reconstruction phase of passive radar reference signals.In the context of reconstructing digital terrestrial multimedia broadcasting(DTMB)signals for low-slow-small(LSS)target detection,a novel frequency domain block joint equalization algorithm is presented in this article.From the DTMB signal frame structure and channel multipath transmission characteristics,this article adopts a unconventional approach where the delay and frame structure of each DTMB signal frame are reconfigured to create a circular convolution block,facilitating concurrent fast Fourier transform(FFT)calculations.Following equalization,an inverse fast Fourier transform(IFFT)-based joint output and subsequent data reordering are executed to finalize the equalization process for the DTMB signal.Simulation and measured data confirm that this algorithm outperforms conventional techniques by reducing signal errors rate and enhancing real-time processing.In passive radar LSS detection,it effectively suppresses multipath and noise through frequency domain equalization,reducing false alarms and improving the capabilities of weak target detection.

Compensatory Damages in Personal Information Public Interest Litigation in China: Challenges and Prospects

In contrast to private interest litigation,public interest litigation provides a more potent solution to personal information infringements marked by extensive scope,unspecified victims,and limited individual loss.However,com⁃pensatory damages remain a contentious issue,both in theory and in practice,within the legal framework of personal in⁃formation public interest litigation.Through an empirical study conducted within China's judicial practice,this paper reveals that the pending issue concerning the nature and function of compensatory damages has caused highly contra⁃dictory verdicts regarding their calculation and allocation,as well as their relationship with other forms of pecuniary li⁃abilities.Only by acknowledging the role of compensatory damages imposed in personal information public interest liti⁃gation as"Skimming off Excess Profits",and affirming their function as deterrence rather than compensation can they truly achieve the broader objective of safeguarding personal information security and promoting public welfare,as well as avoid disrupting the harmony of the existing legal landscape.

GENDER EQUALITY IN THE CHINESE WORKPLACE

Gender equality is a significant issue in the economic and social sectors.A McKinsey study found that promoting gender equality in the workplace could contribute US$13 trillion to global GDP growth.And if China reaches the forefront of gender equality in the workplace in the Asia-Pacific region,it would generate about US$3 trillion in GDP.

Automatic SOC Equalization Strategy of Energy Storage Units with DC Microgrid Bus Voltage Support

In this paper,an improved sag control strategy based on automatic SOC equalization is proposed to solve the problems of slow SOC equalization and excessive bus voltage fluctuation amplitude and offset caused by load and PV power variations in a stand-alone DC microgrid.The strategy includes primary and secondary control.Among them,the primary control suppresses the DC microgrid voltage fluctuation through the I and II section control,and the secondary control aims to correct the P-U curve of the energy storage system and the PV system,thus reducing the steady-state bus voltage excursion.The simulation results demonstrate that the proposed control strategy effectively achieves SOC balancing and enhances the immunity of bus voltage.The proposed strategy improves the voltage fluctuation suppression ability by approximately 39.4%and 43.1%under the PV power and load power fluctuation conditions,respectively.Furthermore,the steady-state deviation of the bus voltage,△U_(dc) is only 0.01–0.1 V,ensuring stable operation of the DC microgrid in fluctuating power environments.

Pursuing Common Good for All under Heaven

Fairness,justice,and equality are long existing pursuits of Chinese philosophers from ancient times to today.AS a political ideal,the ancient Chinese saying“Tian Xia Wei Gong”,or“pursuing common good for all under heaven”has been influencing Chinese politics and collective mind of the Chinese people since the time Confucius proposed it.

The Rise of China’s Women’s Basketball Team:An Exploration of Gender Equality in Professional Basketball

This article explores the rise of the Chinese women’s basketball team in professional basketball and its relationship to gender equality issues.In view of the gender differences in salary,market value,social status,and other aspects,the article proposes a series of strategies to promote the realization of gender equality for female basketball players in professional basketball.This article points out that the rise of the Chinese women’s basketball team will lead the process of gender equality and lay the foundation for a more equitable and inclusive future.To achieve this goal,this article highlights the importance of improving the competitive level of female athletes,improving basic education,promoting basketball culture,and promoting gender equality.

Functional Dependence of IM and HV Angle in Hallux Valgus Deformity before and after Operative

Hallux valgus is a relatively common and multifaceted complex deformity of the front part of the foot. It is the result of multiple effects of innate (endogenous) and exogenous etiological factors with different degrees of influence. The degree of hallux valgus deformity is usually assessed by radiological values of hallux valgus (HV) and intermetatarsal (IM) angles. The aim of the paper is to justify the definition of hallux valgus deformity as a function of one angle, (HVA or IMA), and then to determine the functional connection and the most suitable function equalizing the values of the angles IMA and HVA. As hallux valgus is a double angulation deformity, the analytically determined connection between the HVA and IMA angles reduces the study of the deformity to the study of function with one argument, and makes the analysis of deformity changes before and after operative treatment simpler. For the determined connections between the angles, the values of linear proportionality coefficients and regression coefficients of corresponding linear functions of analytical equalization of the value of the IM angle and the degree of deformity for a given value of the HV angle were experimentally determined. The obtained results were checked on a sample of 396 operatively treated hallux valgus deformities. The presented analytical approach and the obtained functional links of IMA and HVA enable quantitative observation of the change in the degree of deformity based on the radiologically determined value of these angles, and the established nonlinear function will be useful for evaluating the expected value of the IM angle and the degree of deformity based only on the measured value of the HV angle. .

Near-Field Beam Training for Holographic MIMO Communications: Typical Methods, Challenges and Future Directions

Holographic multiple-input multiple-output(HMIMO)has become an emerging technology for achieving ultra-high frequency spectral efficiency and spatial resolution in future wireless systems.The increasing antenna aperture leads to a more significant characterization of the spherical wavefront in near-field communications in HMIMO scenarios.Beam training as a key technique for wireless communication is worth exploring in this near-field scenario.Compared with the widely researched far-field beam training,the increased dimensionality of the search space for near-field beam training poses a challenge to the complexity and accuracy of the proposed algorithm.In this paper,we introduce several typical near-field beam training methods:exhaustive beam training,hierarchical beam training,and multi-beam training that includes equal interval multi-beam training and hash multi-beam training.The performances of these methods are compared through simulation analysis,and their effectiveness is verified on the hardware testbed as well.Additionally,we provide application scenarios,research challenges,and potential future research directions for near-field beam training.

Microstructure and mechanical properties of Mg-Gd-Y-Zr alloy processed by equal channel angular pressing

Microstructure evolution and texture development and their effects on mechanical properties of a Mg-Gd-Y-Zr alloy during equal channel angular pressing（ECAP） were investigated.It is found that the microstructure is still inhomogeneous after four passes,and two zones,namely the fine grain zone（FGZ） and the coarse grain zone（CGZ） are formed.The grain refinement occurs mainly by particle-stimulated nucleation（PSN） mechanism,which led to a more random texture after four passes of ECAP.In the ECAP-processed alloy,the strength did not increase while the ductility was enhanced dramatically compared with the as-received condition.The change of ductility of this alloy was discussed in terms of texture and second phase particles.

Equal channel angular extrusion of NiTi shape memory alloy tube

As a new attempt, equal channel angular extrusion （ECAE） of nickel-titanium shape memory alloy （NiTi SMA） tube was investigated by means of process experiment, finite element method （FEM） and microscopy. NiTi SMA tube with the steel core in it was inserted into the steel can during ECAE of NiTi SMA tube. Based on rigid-viscoplastic FEM, multiple coupled boundary conditions and multiple constitutive models were used for finite element simulation of ECAE of NiTi SMA tube, where the effective stress field, the effective strain field and the velocity field were obtained. Finite element simulation results are in good accordance with the experimental ones. Finite element simulation results reveal that the velocity field shows the minimum value in the corner of NiTi SMA tube, where severe shear deformation occurs. Microstructural observation results reveal that severe plastic deformation leads to a certain grain orientation as well as occurrence of substructures in the grain interior and dynamic recovery occurs during ECAE of NiTi SMA tube. ECAE of NiTi SMA tube provides a new approach to manufacturing ultrafine-grained NiTi SMA tube.