Comparative impact behaviours of ultra high performance concrete columns reinforced with polypropylene vs steel fibres

Polypropylene(PP) fibres have primarily used to control shrinkage cracks or mitigate explosive spalling in concrete structures exposed to fire or subjected to impact/blast loads, with limited investigations on capacity improvement. This study unveils the possibility of using PP micro-fibres to improve the impact behaviour of fibre-reinforced ultra-high-performance concrete(FRUHPC) columns. Results show that the addition of fibres significantly improves the impact behaviour of FRUHPC columns by shifting the failure mechanism from brittle shear to favourable flexural failure. The addition of steel or PP fibres affected the impact responses differently. Steel fibres considerably increased the peak impact force(up to 18%) while PP micro-fibres slightly increased the peak(3%-4%). FRUHPC significantly reduced the maximum midheight displacement by up to 30%(under 20°impact) and substantially improved the displacement recovery by up to 100%(under 20° impact). FRUHPC with steel fibres significantly improved the energy absorption while those with PP micro-fibres reduced the energy absorption, which is different from the effect of PP-macro fibre reported in the literature. The optimal fibre content for micro-PP fibres is 1% due to its minimal fibre usage and low peak and residual displacement. This study highlights the potential of FRUHPC as a promising material for impact-resistant structures by creating a more favourable flexural failure mechanism, enhancing ductility and toughness under impact loading, and advancing the understanding of the role of fibres in structural performance.

Overview of Jute Fibre as Thermoplastic Matrix Polymer Reinforcement

Recent decades have seen a substantial increase in interest in research on natural fibres that is aligned with sustainable development goals(SDGs).Due to their renewable resources and biodegradability,natural fiberreinforced composites have been investigated as a sustainable alternative to synthetic materials to reduce the usage of hazardous waste and environmental pollution.Among the natural fibre,jute fibre obtained from a bast plant has an increasing trend in the application,especially as a reinforcement material.Numerous research works have been performed on jute fibre with regard to reinforced thermoset and thermoplastic composites.Nevertheless,current demands on sustainable materials have required new developments in thermoplastic composites.In this paper,the author reviews jute plants as reinforcement materials for thermoplastic matrix polymers.This review provides an overview of the sustainability of jute plants as reinforcement material for thermoplastic matrix polymers.The overview on jute based thermoplastic composites focused on the thermal behavior and mechanical properties.Apart from physical,chemical,and mechanical properties,the study also covers the current and perspectives for future research challenges faced by the researchers on jute fibre reinforced thermoplastic composites.

Path-Dependent Progressive Failure Analysis for 3D-Printed Continuous Carbon Fibre Reinforced Composites

In order to predict the damage behaviours of 3D-printed continuous carbon fibre(CCF)reinforced composites,when additional short carbon fibre(SCF)composite components are employed for continuous printing or special functionality,a novel path-dependent progressive failure(PDPF)numerical approach is developed.First,a progressive failure model using Hashin failure criteria with continuum damage mechanics to account for the damage initiation and evaluation of 3D-printed CCF reinforced polyamide(PA)composites is developed,based on actual fibre placement trajectories with physical measurements of 3D-printed CCF/PA constituents.Meanwhile,an elastic-plastic model is employed to predict the plastic damage behaviours of SCF/PA parts.Then,the accuracy of the PDPF model was validated so as to study 3D-printed CCF/PA composites with either negative Poisson's ratio or high stiffness.The results demonstrate that the proposed PDPF model can achieve higher prediction accuracies in mechanical properties of these 3D-printed CCF/PA composites.Mechanism analyses show that the stress distribution is generally aggregated in the CCF areas along the fibre placement paths,and the shear damage and matrix tensile/compressive damage are the key damage modes.This study provides a new approach with valuable information for characterising complex 3D-printed continuous fibre-matrix composites with variable mechanical properties and multiple constituents.

In Situ Polymer Gel Electrolyte in Boosting Scalable Fibre Lithium Battery Applications

The poor interfacial stability not only deteriorates fibre lithium-ion batteries(FLBs)performance but also impacts their scalable applications.To efficiently address these challenges,Prof.Huisheng Peng team proposed a generalized channel structures strategy with optimized in situ polymerization technology in their recent study.The resultant FLBs can be woven into different-sized powering textiles,providing a high energy density output of 128 Wh kg^(-1) and simultaneously demonstrating good durability even under harsh conditions.Such a promising strategy expands the horizon in developing FLB with particular polymer gel electrolytes,and significantly ever-deepening understanding of the scaled wearable energy textile system toward a sustainable future.

Optical Fibre Communication Feature Analysis and Small Sample Fault Diagnosis Based on VMD-FE and Fuzzy Clustering

To solve the problems of a few optical fibre line fault samples and the inefficiency of manual communication optical fibre fault diagnosis,this paper proposes a communication optical fibre fault diagnosis model based on variational modal decomposition(VMD),fuzzy entropy(FE)and fuzzy clustering(FC).Firstly,based on the OTDR curve data collected in the field,VMD is used to extract the different modal components(IMF)of the original signal and calculate the fuzzy entropy(FE)values of different components to characterize the subtle differences between them.The fuzzy entropy of each curve is used as the feature vector,which in turn constructs the communication optical fibre feature vector matrix,and the fuzzy clustering algorithm is used to achieve fault diagnosis of faulty optical fibre.The VMD-FE combination can extract subtle differences in features,and the fuzzy clustering algorithm does not require sample training.The experimental results show that the model in this paper has high accuracy and is relevant to the maintenance of communication optical fibre when compared with existing feature extraction models and traditional machine learning models.

BTMA’s advanced fibre focus at Techtextil 2024

New fibres continue to be developed for a wide range of technical textile applications.Currently,they include fibres based on organic or recycled feedstocks to meet sustainability targets and others with new functional properties for advanced high performance applications.Many of them were showcased at the forthcoming Techtextil 2024 exhibition which takes place in Frankfurt,Germany,from April 23-26.The development of specific multifilaments,monofilaments and nonwovens for niche fibre applications–over 70 to date–is very much the specialist field of BTMA member Fibre Extrusion Technologies(FET),along with designing the bespoke fibre extrusion and spunbond and meltblown nonwoven systems to successfully produce them.

Fabrication of SiC fibres from yttrium-containing polycarbosilane

The yttrium as a sintering aid was introduced into polycarbosilane（PCS） to prepare yttrium-containing PCS（PYCS）.Two types of yttrium-containing SiC fibres,the SiC（OY） fibres and the SiC（Y） fibres,were fabricated with PYCS.The structural evolution and the associated properties on changing from SiC（OY） to SiC（Y） fibres during the sintering process were studied.The chemical composition of the SiC（OY） fibres is SiC1.53O0.22Y0.005 with an amorphous structure.The composition of SiC（Y） fibres is SiC1.23O0.05Y0.005.The fibres are composed of a large number of β-SiC crystallites with a size of 50 nm and a small amount of α-SiC crystalline.The tensile strength and fracture toughness of the SiC（OY） fibres are 2.25 GPa and 2.37 MPa·m1/2,respectively,and 1.61 GPa,1.91 MPa·m1/2,respectively for SiC（Y） fibres.The SiC（Y） fibres have a higher thermal stability than the SiC（OY） fibres.

Caustics study of the effect of glass fibres on dynamic fracture of hardened cement paste

The reflected optical caustics method is applied to study dynamic fracture problems in hardened cement paste. First both the unreinforced cement paste and the glass fibres reinforced cement paste specimens were fabricated and the reflective coating on the surface of the specimen was prepared. Secondly the crack path and the shadow spot patterns during the crack propagation process for the two specimens were recorded by using a multi-spark high speed camera.Thirdly some dynamic parameters of two cement paste specimens including crack onset time the dynamic stress intensity factor and crack growth velocity were determined and analyzed comparatively.This indicates that the glass fibres can improve the fracture resistance and delay fracture time.These results will play an important role in evaluating the dynamic fracture properties of cement paste.

Fibre Channel主机适配器的研究与设计

本文在分析 Fibre Channel各层协议标准的基础上 ,重点介绍了用于 PC机上 Fibre Channel适配器的工作原理 ,研究了实现 Fibre Channel主机适配器的策略 ,提出了一套设计 Fibre Channel主机适配器的方案 .

两种网络存储协议Fibre channe1与iSCSI比较分析

并行SCSI受到传输距离和连接设备数的限制,不能满足海量信息存储应用的需要。光纤通道和iSCSI作为两种重要的网络存储协议,已得到广泛的研究和应用,都可以用于高性能数据存储和容灾系统中传输SCSI协议数据。从协议模型、协议特点和I/O性能几个方面对这两种协议进行了详细的比较分析,指出了各自的特点和应用领域。

Fracture Properties of Cement Composites Reinforced with Steel Polypropylene Hybrid Fibres

Polypropylene fibres and three sizes of steel fibres reinforced concrete are discussed. The total fibres content ranges from 0 4%-0 95% by volume of concrete. A four point bending test is adopted on the notched prisms with the size of 100?mm×100?mm×500?mm to investigate the effect of hybrid fibres on crack arresting. The research results show that there is a positive synergy effect between large steel fibres and polypropylene fibres on the load bearing capacity in the small displacement range. But this synergy effect disappears in the large displacement range. The large and strong steel fibre is better than soft polypropylene fibre and small steel fibre in the aspect of energy absorption capacity in the large displacement range. The static usage limitation for the hybrid fibres concrete with “wide peak' or “multi peaks' load CMOD pattern should be carefully selected. The ultimate load bearing capacity and the crack width or CMOD at this load level should be jointly considered.

Experiment and simulation of creep performance of basalt fibre asphalt mortar under uniaxial compressive loadings

The creep performance of basalt fibre（BF）reinforced in asphalt mortar under uniaxial compressive loadings is investigated. The samples of basalt fibre asphalt mortar（BFAM） with different BF mass fractions（0. 1%,0. 2%, and 0. 5%） and without BF in asphalt mixture are prepared, and then submitted for the compressive strength test and corresponding creep test at a high in-service temperature.Besides, numerical simulations in finite element ABAQUS software were conducted to model the compressive creep test of mortar materials, where the internal structure of the fibre mortar was assumed to be a two-component composite material model such as fibre and mortar matrix. Finally, the influence factors of rheological behaviors of BFAM are further analyzed. Results indicate that compared to the control sample, the compressive strength of BFAM samples has a significant increase, and the creep and residual deformation are decreased. However, it also shows that the excessive fibre, i.e. with the BF content of 0. 5%, is unfavorable to the high-temperature stability of the mortar. Based on the analysis results, the prediction equations of parameters of the Burgers constitutive model for BFAM are proposed by considering the fibre factors.

Interfacial microstructure and chemical stability during diffusion bonding of single crystal Al_2O_3-fibres with Ni25.8Al9.6Ta8.3Cr matrix

BN coated A1203 fibre-reinforced NiAl-alloy composites were fabricated by hot pressing at 1 200-1 400 ℃, and the interracial microstructure and chemical stability of BN coated Al2O3 fibre-reinforced NiAl-alloy composites were investigated by scanning electron microscopy （SEM） and analytical transmission electron microscopy （TEM）. It was found that the complicated chemical reactions and diffusion processes happened in the interface area between BN-layer and Ni25.8A19.6Ta8.3 during the hot pressing at 1 200-1 400 ℃. A continuous AlN-layer was formed at the interface due to the reaction between NiAl and BN. At the same time, Cr diffused extensively into the BN-layer and reacted with boron to form Cr boride precipitates （CrsB3）. In addition, a few particles of Ta-rich phase were also precipitated in NiAl matrix near the interface.

基于Fibre Chanel组播的远程数据备份体系结构

数据备份是容灾的基础。本文提出了一种基于FC组播服务的远程数据备份方法,对其工作原理和所涉及到的粗波分复用和流量控制等关键技术进行了研究,对基于FC组播的数据备份系统的性能和所属的容灾层次等内容进行了分析。

Construction monitoring of lock head base plate using distributed optical fibre sensing technique

The concrete hydration heat release process of the base plate is monitored using Roman optical time domain reflectometry（ROTDR） sensing sensors. The monitoring data shows that the internal maximum temperature of the base plate is about 54 ℃ after the concrete was cured for 120 h. The fiber Bragg grating （FBG） temperature sensors are adopted to measure the surface temperature of the concrete and the temperature results are used to compensate the data measured by the pulse-prepump Brillouin optical time-domain analyzer （PPP-BOTDA） to obtain the real concrete surface strain of the base plate. The monitoring data is analyzed to obtain a clear understanding of the strain state of the base plate under the effect of concrete hydration heat release. The monitoring results demonstrate the potential of distributed optical fibre sensing techniques as a powerful tool in real-time construction monitoring, and also provide an important insight into the design, construction and maintenance of large hydraulic structures.

The role of dietary fibre in pig production,with a particular emphasis on reproduction

Fibres from a variety of sources are a common constituent of pig feeds. They provide a means to utilise locallyproduced plant materials which are often a by-product of the food or drink industry. The value of a high fibre diet in terms of producing satiety has long been recognised. However the addition of fibre can reduce feed intake, which is clearly detrimental during stages of the production cycle when nutrient needs are high, for example in growing piglets and during lactation. More recently, fibre has been found to promote novel benefits to pig production systems,particularly given the reduction in antimicrobial use world-wide, concern for the welfare of animals fed a restricted diet and the need to ensure that such systems are more environmentally friendly. For example, inclusion of dietary fibre can alter the gut microbiota in ways that could reduce the need for antibiotics, while controlled addition of certain fibre types may reduce nitrogen losses into the environment and so reduce the environmental cost of pig production.Of particular potential value is the opportunity to use crude fibre concentrates as ’functional’ feed additives to improve young pig growth and welfare. Perhaps the greatest opportunity for the use of high fibre diets is to improve the reproductive efficiency of pigs. Increased dietary fibre before mating improves oocyte maturation, prenatal survival and litter size; providing a consumer-acceptable means of increasing the amount of saleable meat produced per sow. The mechanisms responsible for these beneficial effects remain to be elucidated. However, changes in plasma and follicular fluid concentrations of key hormones and metabolites, as well as effects of the hypothalamic satiety centre on gonadotrophin secretion and epigenetic effects are strong candidates.

Advances in fibre optic based geotechnical monitoring systems for underground excavations

Geotechnical stability is a major concern for the long-term safety and integrity of underground infrastructures such as tunnels, railway stations, mine shafts and hydraulic power chambers. An effective geotechnical monitoring system is able to provide adequate warning to underground personnel prior to any unexpected major geotechnical failure. This paper reviews the conventional geotechnical monitoring sensors and the emerging Fibre Optic Sensing(FOS) techniques, pointing out their unique features and major differences. Recent advances in various FOS based monitoring systems, including Brillouin time domain distributed optical sensors and fibre Bragg grating(FBG) sensors, are investigated through a critical review of the laboratory studies and field applications used for underground geotechnical monitoring. Particular emphasis is given to fibre packaging, temperature compensation, installation methods and instrumentation performance in the underground environment. A detailed discussion of the advantages and limitations of each FOS monitoring system is also presented in this paper.

Dynamics of erbium-doped fibre laser with optical delay feedback and chaotic synchronization

The dynamical behaviour of the erbium-doped fibre single-ring laser with an optical delay feedback is discussed. Simulation shows that as the delay rate increases, the lasing light displays period-doubling which leads to chaos and via reverse period-doubling route returns from chaos to periodic. At a particular delay rate the intermittently chaotic route to chaos is also observed. The identical synchronization based on chaos in this ring laser is demonstrated by numerical simulation.

Effects of melatonin implantation on cashmere yield,fibre characteristics,duration of cashmere growth as well as growth and reproductive performance of Inner Mongolian cashmere goats

Background： Exogenous melatonin could induce cashmere growth. However, induced growth of cashmere fleece by melatonin implants cannot be combined with the typical growth, resulting in earlier shedding followed by another cycle of cashmere growth. To address this issue, we examine the effects on the cashmere yield, fibre characteristics, and the growth and reproductive performance of cashmere goats of planned administration of melatonin. Methods： Eighteen half-sib, female goats were assigned to two treatments （n = 9） including a control and a treatment where melatonin （2 mg/kg BW） was implanted at the end of April and end of June. Cashmere growth and shedding were observed for approximately ] year following implantation. Fibre samples were collected monthly to determine cumulative cashmere length. Initiation and cessation dates for cashmere growth as well as the rate of cashmere growth were calculated. Cashmere yield, weight gain of dam, kidding date, litter size, and birth weight were also recorded. Results： Melatonin implantation increased cashmere yield by 34.5 % （control 553.7 g vs. melatonin 745.0 g; P〈 0.01）, cashmere length by 21.3 % （control 95.2 mm vs. melatonin 115.4 mm; P 〈 0.01）, and decreased fibre diameter by 4.4 % （control 14.6 pm vs. melatonin 14.0 IJm; P 〈 0.03）. In melatonin-treated goats, the average initiation date was earlier than in control goats （May 18, 2013 vs. July 2, 20]3; P〈 0.01） but there was a similar cessation date （March 22, 2014 vs. March 27, 2014）. Consequently, the duration of cashmere growth was longer in melatonin-treated goats than in control goats （307 vs.270 days; P 〈 0.01）. The final BW, average daily gain, kidding date, litter size, and birth weight were not influenced by melatonin implantation. Conclusions： These data indicate that melatonin implantation （2 mg/kg BW） on two occasions （late April and June） increased cashmere yield by combining the induced growth of cashmere fleece with the typical growth and decreased the fibre diameter without changing dam growth rate or reproductive performance.

Theoretical study and optimization of a high power mid-infrared erbium-doped ZBLAN fibre laser

Based on the rate equations describing the erbium-doped fluoride glass （ZBLAN） fibre lasers with different pumping configurations being taken into account, this paper presents theoretical calculations related to the dynamic population density and the operation performance of a high power mid-infrared all-fibre erbium-doped ZBLAN fibre laser. It shows that the ground-state absorption, excited-state absorption and energy-transfer-upconversion processes co-exist and produce a population balance, causing the laser to operate stably at a continuous wave state. A good agreement between the theoretical results and recent experimental measurement is obtained. Furthermore, the laser structure parameters including fibre length, reflectance of output fibre Bragg grating and pumping configurations are quantitatively optimised to achieve the best performance. The results show, as expected, that the slope efficiency of the fibre laser can be improved significantly through optimisation, which then provides an important guide for the design of high-performance mid-infrared erbium-doped ZBLAN fibre lasers.