A 5MS/s 12-Bit Successive Approximation Analog-to-Digital Converter

With the continuous development of science and technology, digital signal processing is more and more widely used in various fields. Among them, the analog-to-digital converter (ADC) is one of the key components to convert analog signals to digital signals. As a common type of ADC, 12-bit sequential approximation analog-to-digital converter (SAR ADC) has attracted extensive attention for its performance and application. This paper aims to conduct in-depth research and analysis of 12-bit SAR ADC to meet the growing demands of digital signal processing. This article designs a 12-bit, successive approximation analog-to-digital converter (SAR ADC) with a sampling rate of 5 MS/s. The overall circuit adopts a fully differential structure, with key modules including DAC capacitor array, comparator, and control logic. According to the DAC circuit in this paper, a fully differential capacitor DAC array structure is proposed to reduce the area of layout DAC. The comparator uses a digital dynamic comparator to improve the ADC conversion speed. The chip is designed based on the SMIC180 nm CMOS process. The simulation results show that when the sampling rate is 5 MS/s, the effective bit of SAR ADC is 11.92 bit, the SNR is 74.62 dB, and the SFDR is 89.24 dB.

Overview of Energy-Efficient Successive-Approximation Analog-to-Digital Converters: State-of-the-Art and a Design Example

This paper makes a review of state-of-the- arts designs of successive-approximation register analog-to-digital converters （SAR ADCs）. Methods and technique specifications are collected in view of innovative ideas. At the end of this paper, a design example is given to illustrate the procedure to design an SAR ADC. A new method, which extends the width of the internal clock, is also proposed to facilitate different sampling frequencies, which provides more time for the digital-to-analog convert （DAC） and comparator to settle. The 10 bit ADC is simulated in 0.13 μm CMOS process technology. The signal-to-noise and distortion ratio （SNDR） is 54.41 dB at a 10 MHz input with a 50 MS/s sampling rate, and the power is 330 μW.

Effect of ionizing radiation on dual 8-bit analog-to-digital converters (AD9058) with various dose rates and bias conditions

The radiation effects on several properties （reference voltage, digital output logic voltage, and supply current） of dual 8-bit analog-to-digital （A/D） converters （AD9058） under various biased conditions are investigated in this paper. Gamma ray and 10-MeV proton irradiation are selected for a detailed evaluation and comparison. Based on the measurement results induced by the gamma ray with various dose rates, the devices exhibit enhanced low dose rate sensitivity （ELDRS） under zero and working bias conditions. Meanwhile, it is obvious that the ELDRS is more severe under the working bias condition than under the zero bias condition. The degradation of AD9058 does not display obvious ELDRS during 10-MeV proton irradiation with the selected flux.

A 1.5 bit/s Pipelined Analog-to-Digital Converter Design with Independency of Capacitor Mismatch

A new technique which is named charge temporary storage technique (CTST) was presented to improve the linearity of a 1.5 bit/s pipelined analog-to-digital converter (ADC). The residual voltage was obtained from the sampling capacitor, and the other capacitor was just a temporary storage of charge. Then, the linearity produced by the mismatch of these capacitors was eliminated without adding extra capacitor error-averaging amplifiers. The simulation results confirmed the high linearity and low dissipation of pipelined ADCs implemented in CTST, so CTST was a new method to implement high resolution, small size ADCs.

Design of Digital to Analog Converters with Arbitrary Radix

There are DAC structures available in the literature for radix r = 2, 3, and 4;but how they are arrived at is missing. No general structure is available for any radix r. The aim of the paper is, therefore, to fulfil these gaps. To start with, the design relations are derived for the simplest possible attenuator circuit when connected to a voltage source V and a series resistance R, such that the complete circuit offers the Thevenin resistance R. Spread relations for this attenuator are derived. An example when 3 such attenuators with different attenuation constants are connected in cascade is given. Interestingly, the two attenuators with attenuation factors 1/2 and 1/3 have the same spread of 2. A generalized attenuator is then obtained when N number of identical attenuators are connected in cascade. This is modified to derive a digital to analog converter for any radix r.

A Digital Background Calibration Technique for Successive Approximation Register Analog-to-Digital Converter

A digital background calibration technique that corrects the capacitor mismatches error is proposed for successive approximation register analog-to-digital converter (SAR ADC). The technique is implemented in SAR ADC which is based on tri-level switching. The termination capacitor in the Digital-to-Analog Converter (DAC) is regarded as a reference capacitor and the digital weights of all other unit capacitors are corrected with respect to the reference capacitor. To make a comparison between the size of the unit capacitor and that of the reference capacitor, each input sample is quantized twice. The unit capacitor being calibrated is swapped with the reference capacitor during the second conversion. The difference between the two conversion results is used to correct the digital weight of the unit capacitor under calibration. The calibration technique with two reference capacitors is presented to reduce the number of parameters to be estimated. Behavior simulation is performed to verify the proposed calibration technique by using a 12-bit SAR ADC with 3% random capacitor mismatch. The simulation results show that the Signal-to-Noise and Distortion Ratio (SNDR) is improved from 57.2 dB to 72.2 dB and the Spurious Free Dynamic Range (SFDR) is improved from 60.0 dB to 85.4 dB.

Novel Optical Analog-To-Digital Converter Based on Optical Time Division Multiplexing

A novel optical analog-to-digital converter based on optical time division multiplexing(OTDM) is described which uses electrooptic sampling and time-demultiplexing together with multiple electronic analog-to-digital converter(ADC). Compared with the previous scheme, the time-division multiplexer and the time-division demultiplexer are applied in the optical analog-to-digital converter(OADC) at the same time, the design of the OADC is simplified and the performance of the OADC based on time-division demultiplexer is improved. A core optical part of the system is demonstrated with a sample rate of 10 Gs/s. The signals in three channels are demultiplexed from the optical pulses.The result proves our scheme is feasible.

一种16位110 dB无杂散动态范围的低功耗SAR ADC

该文设计了一款16位、转换速率为625 kS/s的逐次逼近寄存器型模数转换器(SAR ADC)。改进的采样保持电路结构,优化了采样线性度和噪声性能。采用分段结构设计电容型数模转换器并使用混合方式的电容切换方案,减小面积和能耗。利用扰动注入技术提升ADC的线性度。比较器采用两级积分型预放大器减小噪声,利用输出失调存储技术及优化的电路设计减小了比较器失调电压和失调校准引入的噪声,优化并提升了比较器速度。芯片采用CMOS 0.18μm工艺设计和流片,ADC核心面积为1.15 mm^(2)。测试结果表明,在1 kHz正弦信号输入下,ADC差分输入峰峰值幅度达8.8 V,信纳比为85.9 dB,无杂散动态范围为110 dB,微分非线性为-0.27/+0.32 LSB,积分非线性为-0.58/+0.53 LSB,功耗为4.31 mW。

高精度低功耗噪声整形SAR ADC设计

针对传统无源有损积分环路滤波器相较于有源无损积分环路滤波器,具有功耗低、电路设计简单等特点,但其噪声传输函数(NTF:Noise Transfer Function)平滑,噪声整形效果较弱的问题,提出了一种无源无损的二阶积分环路滤波器,保留了无源有损积分优点的同时具有良好噪声整形效果。设计了一款分辨率为16 bit、采样率为2 Ms/s的混合架构噪声整形SAR ADC。仿真结果表明,在125 kHz带宽、过采样比为8时,实现了高信号与噪声失真比(SNDR(Signal to Noise and Distortion Ratio)为91.1 dB)、高精度(14.84 bit)和低功耗(285μW)的性能。

一种具有1~128倍可变增益放大器的低功耗Sigma⁃Delta ADC

为满足传感器应用的低功耗需求,设计并实现了一种低功耗Sigma⁃Delta模数转换器(ADC)芯片。该ADC采用一阶全差分开关电容Sigma⁃Delta调制器,且集成了可编程增益放大器(PGA)和Bandgap;使用1.5 bit量化结构,相较于1 bit量化结构减小了3 dB的量化误差;使用优化的反馈电路,减小了电容失配引入的误差;PGA采用轨到轨的运放电路拓扑,增大了整个芯片的电压适应范围。基于180 nm CMOS工艺对该ADC进行了设计和流片。测试结果表明:该Sigma⁃Delta ADC在采样频率512 kHz、过采样率(OSR)为256时,峰值信噪谐波失真比(SNDR)和有效位数(ENOB)分别为75.29 dB和12.21 bit,芯片功耗仅为0.92 mW。芯片能在2.3~5.5 V宽电源电压范围内正常工作,可实现最大128 V/V的增益。适用于小型传感器的信号测量应用,可以满足小型传感器低功耗、高精度的需求。

基于高速ADC的数字双混频时差测量系统

使用双混频时差法进行时间和频率测量时,模拟部分引入的噪声会干扰信号过零点的判断,降低测量精度,而使用数字信号处理技术后不再需要判断过零点,量化噪声成为系统内的主要噪声来源,可以通过数字滤波器对其进行抑制。同时有利于设计结构紧凑的系统,更易于小型化,测量速度也可以进行灵活配置。通过引入高速模数转换器、数控振荡器、低通抽取滤波器、数字鉴相器等,设计了数字双混频时差测量系统,并研制了4通道的原理样机。测试结果表明,当频率源为10 MHz的信号时,原理样机中属于同片ADC(analog-to-digital converter)的两个通道间的本底噪声约为5×10^(-14)@1 s,属于不同片ADC的两个通道间的本底噪声约为8×10^(-14)@1 s,满足原子振荡器的测量要求。并以主动型氢钟VCH-1003M为参考,使用原理样机分别对Microchip的5071A铯原子钟和SRS的FS725铷原子钟的稳定度进行测量,测量结果与Microchip的相噪分析仪53100A和5120A无显著差异。

ADC border effect and suppression of quantization error in the digital dynamic measurement

The digital measurement and processing is an important direction in the measurement and control field. The quantization error widely existing in the digital processing is always the decisive factor that restricts the development and applications of the digital technology. In this paper, we find that the stability of the digital quantization system is obviously better than the quantization resolution. The application of a border effect in the digital quantization can greatly improve the accuracy of digital processing. Its effective precision has nothing to do with the number of quantization bits, which is only related to the stability of the quantization system. The high precision measurement results obtained in the low level quantization system with high sampling rate have an important application value for the progress in the digital measurement and processing field.

单极性ADC静态参数的测试方法

模数转换器(ADC)的静态指标包括微分非线性(DNL)和积分非线性(INL),测量静态参数的主要方法为码密度直方图法。传统的码密度直方图法对输入正弦波的幅值的计算精度有较高的要求,提出了一种基于码密度直方图的归一化处理的平台方案。根据测试要求,选取符合要求的测试激励幅值输入,从而对归一化处理后的方案有效性进行验证。实验结果表明进行归一化处理降低了正弦波幅值的变化对于码密度直方图法的影响,提高了码密度直方图法测试的稳定性。

基于FPGA的多片ADC同步设计与实现

本文通过利用模数转换器的测试模式可实现对多片ADC高速采集系统的同步设计。该设计方案,可保证相控阵雷达多通道的相位一致性,确保方位和俯仰角度测量的准确性。通过外部模拟信号源对该系统进行功能测试,并通过Matlab对测试结果进行分析,确定通道间的相位关系,对该设计方案的功能性及稳定性进行了验证。

A FAST FOREGROUND DIGITAL CALIBRATION TECHNIQUE FOR PIPELINED ADC

Digital calibration techniques are widely developed to cancel the non-idealities of the pipelined Analog-to-Digital Converters (ADCs). This letter presents a fast foreground digital calibration technique based on the analysis of error sources which influence the resolution of pipelined ADCs. This method estimates the gain error of the ADC prototype quickly and calibrates the ADC simultaneously in the operation time. Finally, a 10 bit, 100 Ms/s pipelined ADC is implemented and calibrated. The simulation results show that the digital calibration technique has its efficiency with fewer operation cycles.

一种具有纹波消除技术的10 bit SAR ADC

逐次逼近寄存器模数转换器(SAR ADC)在逐次逼近的过程中,电容的切换会使参考电压上出现参考纹波噪声,该噪声会影响比较器的判定,进而输出错误的比较结果。针对该问题,基于CMOS 0.5μm工艺,设计了一种具有纹波消除技术的10 bit SAR ADC。通过增加纹波至比较器输入端的额外路径,将参考纹波满摆幅输入至比较器中;同时设计了消除数模转换器(DAC)模块,对参考纹波进行采样和输入,通过反转纹波噪声的极性,消除参考纹波对ADC输出的影响。该设计将信噪比(SNR)提高到56.75 dB,将有效位数(ENOB)提升到9.14 bit,将积分非线性(INL)从-1~5 LSB降低到-0.2~0.3 LSB,将微分非线性(DNL)从-3~4 LSB降低到-0.5~0.5 LSB。

DIGITAL BACKGROUND CALIBRATION OF CAPACITOR MISMATCHES AND HARMONIC DISTORTION IN PIPELINED ADC

A correlation-based digital background calibration algorithm for pipelined Analog-to- Digital Converters (ADCs) is presented in this paper. The merit of the calibration algorithm is that the main errors information, which include the capacitor mismatches and residue amplifier distortion, are extracted integrally. A modified 1st pipelined stage is adopted to solve the signal overflow caused by the Pseudo-random Noise (PN) sequences. Behavioral simulation results verify the effectiveness of the algorithm. It improves the Signal-to-Noise-plus-Distortion Ratio (SNDR) and Spurious-Free-Dynamic-Range (SFDR) of the pipelined ADC from 41.8 dB to 78.3 dB and 55.6 dB to 98.6 dB, respectively, which is comparable to the prior arts.

应用于24G雷达芯片系统的12 bit 50 MS/s SAR ADC

针对24G雷达芯片的设计需要,设计了一款12 bit、采样率为50 MS/s的逐次逼近型模数转换器(SARADC)。整体架构采用全差分形式,采用改进型的分裂式电容阵列,提高CDAC的建立速度。同时,采用二进制重组权重的冗余校正算法,进一步提高系统线性度。利用优化的Strong-arm比较器结构,与异步时序配合,提高ADC的工作速度。电路采用SMIC 40 nmCMOS工艺进行设计,后仿真结果表明,在电源电压为1.1 V,采样率为50 MS/s下,输入信号频率约为5 MHz的正弦信号,无杂散动态范围为80.6 dBc,信噪失真比为71.5 dB,有效位数能够达到11.58 bit。

Analog-to-digital conversion of information in the retina

We considered the physiological mechanisms of functioning of the retina’s neural network. It is marked that the primary function of a neural network is an analog-to-digital conversion of the receptor potential of photoreceptor into the pulse-to-digital signal to ganglion cells. We showed the role of different types of neurons in the work of analog-to-digital converter. We gave the equivalent circuit of this converter. We researched the mechanism of the numeric coding of the receptor potential of the photoreceptor.

基于增强线性度和降低功耗的ADC设计与优化

阐述模拟-数字转换器ADC的基本原理和分类,提出多种设计策略和优化方法,包括子级位校准与动态校准技术的结合、混合信号与数字处理器的协同设计等创新应用。探讨多级校准与自适应校准技术、低功耗模式与动态电源管理的优化策略。