Quality Evaluation and Comprehensive Analysis of Flue-cured Tobacco Leaf in Fuzhou

The appearance quality, physical properties, chemical components and sensory quality of 69 flue-cured tobacco leaf samples from 6 counties of Fuzhou City in 2013 were analyzed and evaluated, and were compared with those in southeast area of China. The results showed that the flue-cured tobacco leaves in Fuzhou in 2013 had better hygroscopicity, toughness and filling ability, as well as suitable dragging force. However, some of the tobacco leaves were slightly thin, and had relatively high stem ratio. The tobacco leaves in Fuzhou had higher potassium content, lower starch content, and higher potassium to chlorine ratio. The middle tobacco leaves had better coordination of chemical components and general sensory quality（medium to medium-super level）. Most upper and middle flue-cured tobacco leaf samples had medium-super aroma quality, relatively sufficient aroma quantity,and relatively concentrated smoke; while the lower flue-cured tobacco leaves had little aroma quantity and insufficient smoke. The appearance quality score of lower tobacco leaf samples in Fuzhou in 2013 was slightly lower than that in southeastand whole China. The scores of maturity and leaf structure of middle tobacco leaves in Fuzhou were equivalent to those in southeast China and the national averages.The upper leaves in Fuzhou obtained an equivalent score in oil content and slightly lower scores in other indexes as compared with those in southeast China.The middle-lower tobacco leaves in Fuzhou had better hygroscopicity and toughness compared with those in southeastand whole China. The total alkaloid content per plant andreducing sugar content and potassium content in the middle and lower parts were higher than those in southeast and whole China. However, the scores of coordination of chemical components of lower and upper tobacco leaves in Fuzhou were slightly lower than those in southeast and whole China. The sensory quality of the 3 parts of tobacco leaves in Fuzhou were similar to that in southeast and whole China, but the score of consistency of upper tobacco leaves in Fuzhou was slightly higher.

Safety monitoring and stability analysis of left abutment slope of Jinping Ⅰ hydropower station

Safety monitoring and stability analysis of high slopes are important for high dam construction in high mountainous regions or precipitous gorges. In this paper, deformation characteristics of toppling block at upper abutment, deforming tensile rip wedge in the middle part and deep fractures are comprehensively analyzed based on the geological conditions, construction methods and monitoring results of left abutment slope in Jinping Ⅰ hydropower station. Safety analyses of surface and shallow-buried rock masses and the corresponding anchorage system are presented. The monitoring results indicate that the global stability of the large wedge block in the left abutment is effectively under control, and the abutment slope is stable in a global sense. After the completion of excavation, the deformations of toppling block at the top of the slope and deep fracture zone continue at a very low rate, which can be explained as 'rock mass creep'. Further monitoring and analysis are needed.

System failure analysis based on DEMATEL–ISM and FMECA

A new method of system failure analysis was proposed. First, considering the relationships between the failure subsystems,the decision making trial and evaluation laboratory(DEMATEL) method was used to calculate the degree of correlation between the failure subsystems, analyze the combined effect of related failures, and obtain the degree of correlation by using the directed graph and matrix operations. Then, the interpretative structural modeling(ISM) method was combined to intuitively show the logical relationship of many failure subsystems and their influences on each other by using multilevel hierarchical structure model and obtaining the critical subsystems. Finally, failure mode effects and criticality analysis(FMECA) was used to perform a qualitative hazard analysis of critical subsystems, determine the critical failure mode, and clarify the direction of reliability improvement.Through an example, the result demonstrates that the proposed method can be efficiently applied to system failure analysis problems.

Study of testability measurement method for equipment based on Bayesian network model

To analyze and evaluate the testability design of equipment, a testability analysis method based on Bayesian network inference model is proposed in the paper. The model can adequately apply testability information and many uncertainty information of design and maintenance process, so it can analyze testability by and large from Bayesian inference. The detailed procedure to analyze and evaluate testability for equipments by Bayesian network is given in the paper. Its modeling process is simple, its formulation is visual, and the analysis results are more reliable than others. Examples prove that the analysis method based on Bayesian network inference can be applied to testability analysis and evaluation for complex equipments.

A Hybrid Set of Complexity Metrics for Large-Scale Object-Oriented Software Systems

Large-scale object-oriented（OO） software systems have recently been found to share global network characteristics such as small world and scale free,which go beyond the scope of traditional software measurement and assessment methodologies.To measure the complexity at various levels of granularity,namely graph,class（and object） and source code,we propose a hierarchical set of metrics in terms of coupling and cohesion-the most important characteristics of software,and analyze a sample of 12 open-source OO software systems to empirically validate the set.Experimental results of the correlations between cross-level metrics indicate that the graph measures of our set complement traditional software metrics well from the viewpoint of network thinking,and provide more effective information about fault-prone classes in practice.