This review summarizes the various techniques developed for fabricating nanotube arrays in porous anodic alumina membranes （AAMs）. After a brief introduction to the fabrication process of AAMs, taking carbons, metal...This review summarizes the various techniques developed for fabricating nanotube arrays in porous anodic alumina membranes （AAMs）. After a brief introduction to the fabrication process of AAMs, taking carbons, metals, semiconductors, organics, biomoleculars, and heterojunctions as typical examples, attention will be focused on the recently established methods to fabricate nanotubes in AAM, including electrochemical deposition, surface sol-gel, modified chemical vapor deposition, atomic layer deposition, and layer-by-layer growth. Every method is demonstrated by one or two reported results. Finally, this review is concluded with some perspectives on the research directions and focuses on the AAM-based nanotubes fields.展开更多
Objective The correlation between various formative conditions and the pore characterizationsof the anodic alumina membrane is investigated to seek the optimal conditions for the formation of anodic aluminamembrane. M...Objective The correlation between various formative conditions and the pore characterizationsof the anodic alumina membrane is investigated to seek the optimal conditions for the formation of anodic aluminamembrane. Methods High purity aluminum foils are used as the starting materials. The anodization is conduc-ted in three types of electrolytes, 3% sulfuric acid, 5% sulfuric acid and 2. 7% oxalic acid, respectively, with dif-ferent voltages at for 48h. The characterizations of the pore size, the effective porosity and the pore porosity areobserved and determined by scanning electron microscopy. The hydraulic conductances of the membranes are meas-ured to confirm that the pores are open and evaluate the permselectivity of the membranes. Results The experi-mental result shows that the ordered pore arrays are obtained for oxidation under our experimental conditions. Withthe increasing of the voltage, the pore size and pore porosity increased significantly (P <0.05) , while the effectiveporosity decreased significantly (P <0.05) with the same electrolyte. The pore size formed in 3% sulfuric acid or5% sulfuric acid is much smaller than in 2. 7% oxalic acid as an electrolyte. The hydraulic conductance of anodicalumina membrane that formed under our experimental condition is higher than those of the membranes are availablecurrently used in clinical. Conclusion The results suggest that the optimal conditions for the formation of anodicalumina membrane that used in hemodialysis are in 3% or 5% sulfuric acid with 12. 5V to 17. 5V at for 48h.展开更多
The anodic porous alumina membranes with a definite pore diameter and aspect ratio were used as templates tosynthesize polymer pillared layer structures. The pillared polymer was produced in the template membrane pore...The anodic porous alumina membranes with a definite pore diameter and aspect ratio were used as templates tosynthesize polymer pillared layer structures. The pillared polymer was produced in the template membrane pores, and thelayer on the template surfaces. Rigid cured epoxy resin, polystyrene and soft hydrogel were chosen to confirm themethodology. The pillars were in the form of either tubes or fibers, which were controlled by the alumina membrane pore surface wettability. The structural features were confirmed by scanning electron microscopy results.展开更多
Highly ordered nanowire/tube arrays of Ni0.5Zn0.5Fe2O4were fabricated by the sol-gel method in the pores of anodic alumina membrane （AAM）. Whether nanowires or nanotubes were fabricated depends on immersion time. Th...Highly ordered nanowire/tube arrays of Ni0.5Zn0.5Fe2O4were fabricated by the sol-gel method in the pores of anodic alumina membrane （AAM）. Whether nanowires or nanotubes were fabricated depends on immersion time. The immersion time was 15- 40 s for nanotubes and over 60 s for nanowires. The topography and crystalline structure of the nanowire arrays were characterized by scanning electron microscopy （SEM）, transmission electron microscopy （TEM）, and X-ray diffraction （XRD）. It was found that the length and diameter of the Ni0.5Zn0.5Fe2O4 nanowires are related to the thickness of the AAM and the diameter of the pores. The results indicated that the Ni0.5Zn0.5Fe2O4 nanowires are uniform and parallel to each other.展开更多
Highly ordered nickel monoxide （NiO） nanowire arrays were fabricated by sol-gel synthesis within the pores of anodic alumina membrane （AAM）. Scanning electron microscopy （SEM）, high resolution transmission elect...Highly ordered nickel monoxide （NiO） nanowire arrays were fabricated by sol-gel synthesis within the pores of anodic alumina membrane （AAM）. Scanning electron microscopy （SEM）, high resolution transmission electron microscopy （HRTEM） and X-ray diffraction （XRD） were used to characterize the topography and crystalloid structure of NiO nanowire arrays. The length and diameter of the NiO nanowires depended on the thickness of the AAM and the diameter of the pores. The results indicated that the NiO nanowires were uniformly assembled into the ordered nanopores of the AAM and paralleled to each other. Nickel monoxide nanotubes were also fabricated with the same method by changing the immersing time. This new method to prepare NiO nanowire arrays may be important from gas sensors to various engineering materials.展开更多
基金the support provided by the Japan Society for the Promotion of Science(JSPS)Fellowship program at the National Institute of Advanced Industrial Science and Technology,Tsukuba,Japanthe National Natural Science Foundation of China(Grant No.10704074)+1 种基金the Special Project of Excellent Young Researchers of Anhui Province,Chinathe Project of Excellent President Scholarship of Chinese Academy of Sciences.
文摘This review summarizes the various techniques developed for fabricating nanotube arrays in porous anodic alumina membranes （AAMs）. After a brief introduction to the fabrication process of AAMs, taking carbons, metals, semiconductors, organics, biomoleculars, and heterojunctions as typical examples, attention will be focused on the recently established methods to fabricate nanotubes in AAM, including electrochemical deposition, surface sol-gel, modified chemical vapor deposition, atomic layer deposition, and layer-by-layer growth. Every method is demonstrated by one or two reported results. Finally, this review is concluded with some perspectives on the research directions and focuses on the AAM-based nanotubes fields.
文摘Objective The correlation between various formative conditions and the pore characterizationsof the anodic alumina membrane is investigated to seek the optimal conditions for the formation of anodic aluminamembrane. Methods High purity aluminum foils are used as the starting materials. The anodization is conduc-ted in three types of electrolytes, 3% sulfuric acid, 5% sulfuric acid and 2. 7% oxalic acid, respectively, with dif-ferent voltages at for 48h. The characterizations of the pore size, the effective porosity and the pore porosity areobserved and determined by scanning electron microscopy. The hydraulic conductances of the membranes are meas-ured to confirm that the pores are open and evaluate the permselectivity of the membranes. Results The experi-mental result shows that the ordered pore arrays are obtained for oxidation under our experimental conditions. Withthe increasing of the voltage, the pore size and pore porosity increased significantly (P <0.05) , while the effectiveporosity decreased significantly (P <0.05) with the same electrolyte. The pore size formed in 3% sulfuric acid or5% sulfuric acid is much smaller than in 2. 7% oxalic acid as an electrolyte. The hydraulic conductance of anodicalumina membrane that formed under our experimental condition is higher than those of the membranes are availablecurrently used in clinical. Conclusion The results suggest that the optimal conditions for the formation of anodicalumina membrane that used in hemodialysis are in 3% or 5% sulfuric acid with 12. 5V to 17. 5V at for 48h.
基金This work was supported by the National Natural Science Foundation of China (No. 20023003 and 20128004).
文摘The anodic porous alumina membranes with a definite pore diameter and aspect ratio were used as templates tosynthesize polymer pillared layer structures. The pillared polymer was produced in the template membrane pores, and thelayer on the template surfaces. Rigid cured epoxy resin, polystyrene and soft hydrogel were chosen to confirm themethodology. The pillars were in the form of either tubes or fibers, which were controlled by the alumina membrane pore surface wettability. The structural features were confirmed by scanning electron microscopy results.
文摘Highly ordered nanowire/tube arrays of Ni0.5Zn0.5Fe2O4were fabricated by the sol-gel method in the pores of anodic alumina membrane （AAM）. Whether nanowires or nanotubes were fabricated depends on immersion time. The immersion time was 15- 40 s for nanotubes and over 60 s for nanowires. The topography and crystalline structure of the nanowire arrays were characterized by scanning electron microscopy （SEM）, transmission electron microscopy （TEM）, and X-ray diffraction （XRD）. It was found that the length and diameter of the Ni0.5Zn0.5Fe2O4 nanowires are related to the thickness of the AAM and the diameter of the pores. The results indicated that the Ni0.5Zn0.5Fe2O4 nanowires are uniform and parallel to each other.
文摘Highly ordered nickel monoxide （NiO） nanowire arrays were fabricated by sol-gel synthesis within the pores of anodic alumina membrane （AAM）. Scanning electron microscopy （SEM）, high resolution transmission electron microscopy （HRTEM） and X-ray diffraction （XRD） were used to characterize the topography and crystalloid structure of NiO nanowire arrays. The length and diameter of the NiO nanowires depended on the thickness of the AAM and the diameter of the pores. The results indicated that the NiO nanowires were uniformly assembled into the ordered nanopores of the AAM and paralleled to each other. Nickel monoxide nanotubes were also fabricated with the same method by changing the immersing time. This new method to prepare NiO nanowire arrays may be important from gas sensors to various engineering materials.
