A Combined Antenna Array Deployment with High Positioning Accuracy and Low Angular Measurement Error

In this paper,an antenna array composed of circular array and orthogonal linear array is proposed by using the design of long and short baseline“orthogonal linear array”and the circular array ambiguity resolution design of multi-group baseline clustering.The effectiveness of the antenna array in this paper is verified by sufficient simulation and experiment.After the system deviation correction work,it is found that in the L/S/C/X frequency bands,the ambiguity resolution probability is high,and the phase difference system error between each channel is basically the same.The angle measurement error is less than 0.5°,and the positioning error is less than 2.5 km.Notably,as the center frequency increases,calibration consistency improves,and the calibration frequency points become applicable over a wider frequency range.At a center frequency of 11.5 GHz,the calibration frequency point bandwidth extends to 1200 MHz.This combined antenna array deployment holds significant promise for a wide range of applications in contemporary wireless communication systems.

New Antenna Array Beamforming Techniques Based on Hybrid Convolution/Genetic Algorithm for 5G and Beyond Communications

Side lobe level reduction(SLL)of antenna arrays significantly enhances the signal-to-interference ratio and improves the quality of service(QOS)in recent and future wireless communication systems starting from 5G up to 7G.Furthermore,it improves the array gain and directivity,increasing the detection range and angular resolution of radar systems.This study proposes two highly efficient SLL reduction techniques.These techniques are based on the hybridization between either the single convolution or the double convolution algorithms and the genetic algorithm(GA)to develop the Conv/GA andDConv/GA,respectively.The convolution process determines the element’s excitations while the GA optimizes the element spacing.For M elements linear antenna array(LAA),the convolution of the excitation coefficients vector by itself provides a new vector of excitations of length N=(2M−1).This new vector is divided into three different sets of excitations including the odd excitations,even excitations,and middle excitations of lengths M,M−1,andM,respectively.When the same element spacing as the original LAA is used,it is noticed that the odd and even excitations provide a much lower SLL than that of the LAA but with amuch wider half-power beamwidth(HPBW).While the middle excitations give the same HPBWas the original LAA with a relatively higher SLL.Tomitigate the increased HPBWof the odd and even excitations,the element spacing is optimized using the GA.Thereby,the synthesized arrays have the same HPBW as the original LAA with a two-fold reduction in the SLL.Furthermore,for extreme SLL reduction,the DConv/GA is introduced.In this technique,the same procedure of the aforementioned Conv/GA technique is performed on the resultant even and odd excitation vectors.It provides a relatively wider HPBWthan the original LAA with about quad-fold reduction in the SLL.

Quantum-Inspired Equilibrium Optimizer for Linear Antenna Array

With the rapid development of communication technology,the problem of antenna array optimization plays a crucial role.Among many types of antennas,line antenna arrays(LAA)are the most commonly applied,but the side lobe level(SLL)reduction is still a challenging problem.In the radiation process of the linear antenna array,the high side lobe level will interfere with the intensity of the antenna target radiation direction.Many conventional methods are ineffective in obtaining the maximumside lobe level in synthesis,and this paper proposed a quantum equilibrium optimizer(QEO)algorithm for line antenna arrays.Firstly,the linear antenna array model consists of an array element arrangement.Array factor(AF)can be expressed as the combination of array excitation amplitude and position in array space.Then,inspired by the powerful computing power of quantum computing,an improved quantum equilibrium optimizer combining quantum coding and quantum rotation gate strategy is proposed.Finally,the proposed quantum equilibrium optimizer is used to optimize the excitation amplitude of the array elements in the linear antenna array model by numerical simulation to minimize the interference of the side lobe level to the main lobe radiation.Six differentmetaheuristic algorithms are used to optimize the excitation amplitude in three different arrays of line antenna arrays,the experimental results indicated that the quantum equilibrium optimizer is more advantageous in obtaining the maximum side lobe level reduction.Compared with other metaheuristic optimization algorithms,the quantum equilibrium optimizer has advantages in terms of convergence speed and accuracy.

A 37 GHz Millimeter-Wave Antenna Array for 5G Communication Terminals

This work presents,design and specific absorption rate(SAR)analysis of a 37GHz antenna,for 5th Generation(5G)applications.The proposed antenna comprises of 4-elements of rectangular patch and an even distribution.The radiating element is composed of copper material supported by Rogers RT5880 substrate of thickness,0.254 mm,dielectric constant(εr),2.2,and loss tangent,0.0009.The 4-elements array antenna is compact in size with a dimension of 8mm×20mm in length and width.The radiating patch is excited with a 50 ohms connector i.e.,K-type.The antenna resonates in the frequency band of 37 GHz,that covers the 5G applications.The antenna behavior is studied both in free space and in the proximity of the human body.Three models of the human body,i.e.,belly,hand,and head(contain skin,fat,muscles,and bone)are considered for on-body simulations.At resonant frequency,the antenna gives a boresight gain of 11.6 dB.The antenna radiates efficiently with a radiated efficiency of more than 90%.Also,it is observed that the antenna detunes to the lowest in the proximity of the human body,but still a good impedance matching is achieved considering the−10 dB criteria.Moreover,SAR is also being presented.The safe limit of 2 W/kg for any 10 g of biological tissue,specified by the European International Electro Technical Commission(IEC)has been considered.The calculated values of SAR for human body models,i.e.,belly,hand and head are 1.82,1.81 and 1.09 W/kg,respectively.The SAR values are less than the international recommendations for the three models.Furthermore,the simulated and measured results of the antenna are in close agreement,which makes it,a potential candidate for the fifth-generation smart phones and other handheld devices.

Electric-controlled metasurface antenna array with ultra-wideband frequency reconfigurable reflection suppression

The electric-controlled metasurface antenna array(ECMSAA)with ultra-wideband frequency reconfigurable reflection suppression is proposed and realized.Firstly,an electriccontrolled metasurface with ultra-wideband frequency reconfigurable in-phase reflection characteristics is designed.The element of the ECMSAA is constructed by loading the single electric-controlled metasurface unit on the conventional patch antenna element.The radiation properties of the conventional patch antenna and the reflection performance of electric-controlled metasurface are maintained when the antenna and the metasurface are integrated.Thus,the ECMSAA elements have excellent radiation properties and ultra-wideband frequency reconfigurable in-phase reflection characteristics simultaneously.To take a further step,a 6×10 ECMSAA is realized based on the designed metasurface antenna element.Simulated and measured results prove that the reflection of the ECMSAA is dynamically suppressed in the P and L bands.Meanwhile,high-gain and multi-polarization radiation properties of the ECMSAA are achieved.This design method not only realizes the frequency reconfigurable reflection suppression of the antenna array in the ultra-wide frequency band but also provides a way to develop an intelligent low-scattering antenna.

A Novel Design of Antenna Array with Two K-Band Circularly Polarized Antenna

As an important part of phased array system,the research on phased array antenna is very necessary.The phased array antenna achieves the scanning beam adaptively by regulating the phase difference between each array element.In this paper,a dual K-band circularly polarized antenna with high broadband,broadband beam,wide axial ratio bandwidth and high radiation efficiency is designed.We combine with the advantages of slot antenna and aperture antenna,use multimode waveguide cavity structure to design an aperture antenna,which is fed to waveguide circular polarizer by slot coupling in order to realize circular polarization radiation.Meanwhile,it has the characteristics of broadband,broadband beam,wide axial ratio bandwidth and high radiation efficiency.A slit antenna is designed by using a multimode waveguide cavity structure and a slit coupling feed to a waveguide circular polarizer is used to achieve circularly polarized radiation.The designed antenna consists of two K-band circularly polarized antenna units,and the spacing between the two units is 9.5 mm,which is fed by aK-band T/R module(Transmitter/Receiver module).In order to study the performance of the pattern in the case of the research group,the 2-unit structure is established.The simulation results of frequency–axial ratio bandwidth are given,and the simulation result of the antenna array is shown.The practical results of antenna design and test are also given.

Design of Ka-Band Phased Array Antenna with Calibration Function

In this paper,we have proposed a novel structure of Ka-band based phased array antenna with calibration function.In the design of Kaband antenna,the active phased array system is adopted and the antenna would work in the dual polarization separation mode.We have given out the schematic diagram for the proposed Ka-band antenna,where the Kaband antenna is in the form of waveguide slot array antenna,with 96 units in azimuth and 1 unit in distance.Each group of units is driven by a singlechannel Transmitter/Receiver(T/R)component,and the whole array contains 192 T/R components in total.The size of the T/R component is 55mm(length)×50mm(width)×5.8mm(height),3 Sub-micro Sub-Miniature Push-on(SSMP)blind sockets and a 21-core low-frequency socket are designed on the two sides of the T/R component.In order to meet the technical specifications of phased array antenna,the Ka-band transceiver component is designed based on Low Temperatrue Co-fired Ceramic(LTCC)technology to achieve miniaturization and lightweight.In our approach,the feed network includes two parts:transceiver network and calibration network.The transceiver network consists of 241:8 time-delay power dividers,12 two-way power dividers and 2 six-way time-delay power dividers.The power supply required by theKaband antenna unit is provided to each active component by the power module after Ka band wavelet control distribution.Simulation and measurement results are given in the form of standing wave and scanning capability.

Differential Quasi-Yagi Antenna and Array

A novel differential quasi-Yagi antenna is first presented and compared with a normal single-ended counterpart.The simulated and measured results show that the differential quasi-Yagi antenna outperforms the conventional single-ended one.The differential quasi-Yagi antenna is then used as an element for linear arrays.A study of the coupling mechanism between the two differential and the two singleended quasi-Yagi antennas is conducted,which reveals that the TE0 mode is the dominant mode,and the driver is the decisive part to account for the mutual coupling.Next,the effects of four decoupling structures are respectively evaluated between the two differential quasi-Yagi antennas.Finally,the arrays with simple but effective decoupling structures are fabricated and measured.The measured results demonstrate that the simple slit or air-hole decoupling structure can reduce the coupling level from−18 dB to−25 dB and meanwhile maintain the impedance matching and radiation patterns of the array over the broad bandwidth.The differential quasi-Yagi antenna should be a promising antenna candidate for many applications.

Design of a High-Gain 2 × 1 Array Antenna for S-Band Applications

Antennas are an indispensable element in wireless networks. For long-distance wireless communication, antenna gains need to be very strong (highly directive) because the signal from the antenna loses a lot of strength as it travels over long distances. This is true in the military with missile, radar, and satellite systems, etc. Antenna arrays are commonly employed to focus electromagnetic waves in a certain direction that cannot be achieved perfectly with a single-element antenna. The goal of this study is to design a rectangular microstrip high-gain 2 × 1 array antenna using ADS Momentum. This microstrip patch array design makes use of the RT-DUROID 5880 as a substrate with a dielectric constant of 2.2, substrate height of 1.588 mm, and tangent loss of 0.001. To achieve efficient gain and return loss characteristics for the proposed array antenna, RT-Duroid is a good choice of dielectric material. The designed array antenna is made up of two rectangular patches, which have a resonance frequency of 3.3 GHz. These rectangular patches are excited by microstrip feed lines with 13 mm lengths and 4.8 mm widths. The impedance of the patches is perfectly matched by these transmission lines, which helps to get better antenna characteristics. At a resonance frequency of 3.3 GHz, the suggested antenna array has a directivity of 10.50 dB and a maximum gain of 9.90 dB in the S-band. The S parameters, 3D radiation pattern, directivity, gain, and efficiency of the constructed array antenna are all available in ADS Momentum.

Breast Cancer Detection Based on Multi-Slotted Patch Antenna at ISM Band

The present work designed and investigated a 3D basic model for breast cancer detection at the ISM band. The model consists of two multi-slotted rectangular patch antennas and a three-layer breast phantom containing two tumors. A multi-slotted antenna was designed at 2.45 GHz using CST STUDIO SUITE 2018, where the simulated results showed a return loss better than -35 dB and attended more than 77 MHz bandwidth. The diagnosis approach is based on exploiting the electrical properties (frequency dependent) of breast tissues, i.e., mass density, relative permittivity, and conductivity. Once the proposed slotted antenna radiates electromagnetic signals toward the breast model (with and without tumors), the radiation properties in terms of the scattering parameters (S11 and S21), the electrical field, the power flow, the current density, and the power loss density were altered. As a result, the values of these radiation parameters increased when tumors were implanted inside the breast model, informing the presence of cancerous tissues. Moreover, the specific absorption rate (SAR) was estimated as a function of input powers, where the proposed antenna showed a set of low SAR values compared to the IEEE standard of 1.6 W/kg, validating its potential use for diagnosing purposes. The simulated results indicated the prospective use of two slotted antennas (in the first instance) to detect multiple tumors which could be a challenging task using a single-element antenna, where the ultimate goal is to realize a compact antenna array to detect multi-tumors.

A novel DOA estimation algorithm using directional antennas in cylindrical conformal arrays

In this paper, a novel direction of arrival(DOA) estimation algorithm using directional antennas in cylindrical conformal arrays(CCAs) is proposed. To eliminate the shadow effect, we divide the CCAs into several subarrays to obtain the complete output vector. Considering the anisotropic radiation pattern of a CCA, which cannot be separated from the manifold matrix, an improved interpolation method is investigated to transform the directional subarray into omnidirectional virtual nested arrays without non-orthogonal perturbation on the noise vector. Then, the cross-correlation matrix(CCM) of the subarrays is used to generate the consecutive co-arrays without redundant elements and eliminate the noise vector. Finally, the full-rank equivalent covariance matrix is constructed using the output of co-arrays,and the unitary estimation of the signal parameters via rotational invariance techniques(ESPRIT) is performed on the equivalent covariance matrix to estimate the DOAs with low computational complexity. Numerical simulations verify the superior performance of the proposed algorithm, especially under a low signal-to-noise ratio(SNR) environment.

Analysis of electrical performances of planar active phased array antennas with distorted array plane

The influence of the distorted plane of the active phased array antenna on the electromagnetic performance is of great significance to the research on and development of the high-performance antennas. On the bent and bowl-shape distortion, the model is established of the relationship between the electromagnetic performance and the position error of the radiated elements. The method is presented of analyzing the far-field pattern of the distorted rectangular active phased array antenna. The analysis results of a planar phased array antenna with different distortions grades prove the validity of the model. Therefore, by the method, the antenna designers may set the reasonable requirement on the structural tolerance in manufacturing antenna.

Sparse Planar Retrodirective Antenna Array Using Improved Adaptive Genetic Algorithm

An improved adaptive genetic algorithm is presented in this paper. It primarily includes two modified methods： one is novel adaptive probabilities of crossover and mutation, the other is truncated selection approach. This algorithm has been validated to be superior to the simple genetic algorithm （SGA） by a complicated binary testing function. Then the proposed algorithm is applied to optimizing the planar retrodirective array to reduce the cost of the hardware. The fitness function is discussed in the optimization example. After optimization, the sparse planar retrodirective antenna array keeps excellent retrodirectivity, while the array architecture has been simplified by 34%. The optimized antenna array can replace uniform full array effectively. Results show that this work will gain more engineering benefits in practice.

Decoupling technique of patch antenna arrays with shared substrate by suppressing near-field magnetic coupling using magnetic metamaterials

In this paper,we propose the decoupling technique of patch antenna array by suppressing near-field magnetic coupling（NFMC） using magnetic metamaterials.To this end,a highly-integrated magnetic metamaterials,the substrate-integrated split-ring resonator（SI-SRR）,is firstly proposed to achieve negative permeability at the antenna operating frequency.By integrating SI-SRR in between two closely spaced antennas,magnetic fields are blocked in the shared substrate due to negative permeability of SI-SRR,reducing NFMC between the two antennas.To verify the technique,a prototype was fabricated and measured.The measured results demonstrated that the isolation can be enhanced by more than 17 dB even when the gap between the two patch antennas is only about 0.067 A.Due to high integration,this technique provides an effective alternative to high-isolation antenna array.

Theoretical analysis of ion cyclotron range of frequency antenna array for HT-7U

This paper considers the coupling analysis of phased antenna array designed to excite fast wave in the ion cyclotron range of frequency. The coupling of the antenna is calculated in slab geometry. The coupling code based on the variational principle gives the self-consistent current flowing in the antenna, this method has been extended so that it can be applied to a phased antenna array. As an example, this paper analyses the coupling prosperities of a 2 × 2 phased antenna array. It gives the optimum geometry of antenna array. The fields excited at plasma surface are found to more or less correspond to the antenna current phasing.

Ultra-wideband low radar cross-section metasurface and its application on waveguide slot antenna array

A novel approach devoted to achieving ultra-wideband radar cross section reduction（RCSR） of a waveguide slot antenna array（WGSAA） while maintaining its radiation performance is proposed. Three kinds of artificial magnetic conductors（AMCs） tiles consisting of three types of basic units resonant at different frequencies are designed and arranged in a novel quadruple-triangle-type configuration to create a composite planar metasurface. The proposed metasurface is characterized by low radar feature over an ultra-wideband based on the principle of phase cancellation. Both simulated and measured results demonstrate that after the composite metasurface is used to cover part of the antenna array, an ultrawideband RCSR involving in-band and out-of-band is achieved for co-and cross-polarized incident waves based on energy cancellation, while the radiation performance is well retained. The proposed method is simple, low-cost, and easy-tofabricate, providing a new method for ultra-wideband RCSR of an antenna array. Moreover, the method proposed in this paper can easily be applied to other antenna architectures.

Design of multi-band metasurface antenna array with low RCS performance

In this paper, a multi-band metasurface（MS） antenna array with low radar cross section（RCS） performance is proposed and measured. Firstly, a 44 antenna array is composed of four 22 Jerusalem cross structure antenna arrays working at different frequency bands, which is aimed at enhancing the bandwidth effectively. Then, each antenna can be seen as a unit of MS in spite of adding the feeding structure. Based on phase cancellation principle, the MS is arranged into a chessboard configuration in order to realize wideband RCS reduction. Thus, excellent radiation and scattering characteristics are obtained simultaneously. Simulated and measured results indicate that this work provides a novel method to achieve bandwidth expansion as well as wideband RCS reduction of the antenna array.

A pre-processing blind multiuser detection algorithm based on LSCM using antenna array

A pre-processing blind muhiuser detection algorithms based on the least squares constant modulus （P-LSCMA） using antenna array is proposed in this paper. It first uses the signals received from every antenna to correlate with the conjugation of the DoA vector of the expected user, and then applies the pre-processed signals to the LSCMA. We simulate and compare the proposed algorithm with the conventional LSCMA. Simulation results show that the proposed algorithm is superior to LSCMA.

Worst-case tolerance analysis on array antenna based on chaos-genetic algorithm

This paper studies the effect of amplitude-phase errors on the antenna performance. Via builting on a worst-case error tolerance model, a simple and practical worst error tolerance analysis based on the chaos-genetic algorithm （CGA） is proposed. The proposed method utilizes chaos to optimize initial population for the genetic algorithm （GA） and introduces chaotic disturbance into the genetic mutation, thereby improving the ability of the GA to search for the global optimum. Numerical simulations demonstrate that the accuracy and stability of the worst-case analysis of the proposed approach are superior to the GA. And the proposed algorithm can be used easily for the error tolerant design of antenna arrays.

Integrating electromagnetic surface and antenna array for reflection suppression and excellent radiation

The electromagnetic surface antenna array(EMSAA)has been proposed for obtaining reflection suppression and excellent radiation simultaneously.The antenna with rectangular radiation patch is used to design anisotropic electromagnetic surface.Preternatural reflection characteristics of the element antenna can be tailored depending on the incident polarizations.EMSAA can be constructed by using single structured element antenna with 90° rotation and orthometric arrangement.This orthometric arrangement of EMSAA is helpful to achieve reflection suppression and excellent radiation.The simulated results show that the reflection of EMSAA is suppressed from 5.0 GHz to 8.0 GHz with peak reduction of 12.3 dB.The linear-and circular-polarized radiation properties of EMSAA are obtained and the maximum gain is 14.3 dBi.The measured results are consistent with the simulation results.The results demonstrate that the reflection suppression and excellent radiation are achieved simultaneously.Such design of EMSAA will open the path for integrating antenna fields and electromagnetic surface(EMS)fields.