Antennas are an indispensable element in wireless networks. For long-distance wireless communication, antenna gains need to be very strong (highly directive) because the signal from the antenna loses a lot of str...Antennas are an indispensable element in wireless networks. For long-distance wireless communication, antenna gains need to be very strong (highly directive) because the signal from the antenna loses a lot of strength as it travels over long distances. This is true in the military with missile, radar, and satellite systems, etc. Antenna arrays are commonly employed to focus electromagnetic waves in a certain direction that cannot be achieved perfectly with a single-element antenna. The goal of this study is to design a rectangular microstrip high-gain 2 × 1 array antenna using ADS Momentum. This microstrip patch array design makes use of the RT-DUROID 5880 as a substrate with a dielectric constant of 2.2, substrate height of 1.588 mm, and tangent loss of 0.001. To achieve efficient gain and return loss characteristics for the proposed array antenna, RT-Duroid is a good choice of dielectric material. The designed array antenna is made up of two rectangular patches, which have a resonance frequency of 3.3 GHz. These rectangular patches are excited by microstrip feed lines with 13 mm lengths and 4.8 mm widths. The impedance of the patches is perfectly matched by these transmission lines, which helps to get better antenna characteristics. At a resonance frequency of 3.3 GHz, the suggested antenna array has a directivity of 10.50 dB and a maximum gain of 9.90 dB in the S-band. The S parameters, 3D radiation pattern, directivity, gain, and efficiency of the constructed array antenna are all available in ADS Momentum.展开更多
This paper demonstrates the analysis of antenna pattern and gain for different designs of full-wave dipole antenna feeding techniques. Seven such techniques were studied and analyzed;symmetrical dual feeding in phase,...This paper demonstrates the analysis of antenna pattern and gain for different designs of full-wave dipole antenna feeding techniques. Seven such techniques were studied and analyzed;symmetrical dual feeding in phase, symmetrical dual feeding out of phase, asymmetrical dual feeding in phase, asymmetrical dual feeding out of phase, symmetrical triple feeding in phase and symmetrical triple feeding out of phase. Symmetrical dual feeding in phase produced high gain as compared to the single and center-fed antennas. An improvement of about 3 to 3.5 dB was achieved comparing to center tap fed and off center fed. It was found that an asymmetrical dual feeding in-phase provides good performance, considering the directivity, pattern, and input impedance. A 2.46 dB gain has been attained. It was found that a symmetrical triple feeding provides an overall best performance with respect to gain, radiation pattern, beam width and input impedance.展开更多
A rectangular microstrip patch antenna using conventional Poly Tetra Fluride Ethelene (PTFE) substrate with air cavity is proposed and theoretically investigated. Considerably high gain along with improved front to ba...A rectangular microstrip patch antenna using conventional Poly Tetra Fluride Ethelene (PTFE) substrate with air cavity is proposed and theoretically investigated. Considerably high gain along with improved front to back radiation isolation is demonstrated using such proposed antenna. The radiation performance of this new antenna has been compared to a conventional microstrip patch for some commonly used aspect ratios (width to length ratio). Compared to conventional microstrip antenna the proposed configuration shows more than 12% increment in peak gain and more than 10% increment in front to back radiation performance in each set of aspect ratio. The elucidation of such improvement in the radiation characteristics of the proposed antenna is also presented.展开更多
This paper presents the design of wideband and high gainFrequency Selective Surface(FSS)loaded antenna for ultra-wideband(UWB)wireless applications requiring high-gain.The antenna consists of a monopole and an FSS ref...This paper presents the design of wideband and high gainFrequency Selective Surface(FSS)loaded antenna for ultra-wideband(UWB)wireless applications requiring high-gain.The antenna consists of a monopole and an FSS reflector.Initially,a conventional rectangular monopole antenna is modified using slot and stub to achieve wide operational bandwidth and size reduction.This modified antenna shows 50%miniaturization compared to a primary rectangular monopole,having a wide impedance bandwidth of 3.6-11.8 GHz.Afterward,an FSS is constructed by the combination of circular and square ring structures.The FSS array consisting of 8×8-unit cells are integrated with the antenna as a reflector to enhance the performance of the proposed miniaturized UWB antenna.The loading of FSS results in an improvement of at least 4 dBi gain in the entire operational bandwidth.Moreover,the antenna’s bandwidth is also increased at the lower frequency band due to the presence of the FSS.A prototype of the antenna is fabricated and tested to verify the simulation results.The simulation and measurement results show that the antenna offers a wideband-10 dB impedance bandwidth ranging from 2.55-13GHz with a stable peak gain of 8.6 dBi and retains the radiation pattern stability.展开更多
High gain antennas are highly desirable for long-range wireless communication systems.In this paper,a compact,low profile,and high gain dielectric resonator antenna is proposed,fabricated,experimentally tested,and ver...High gain antennas are highly desirable for long-range wireless communication systems.In this paper,a compact,low profile,and high gain dielectric resonator antenna is proposed,fabricated,experimentally tested,and verified.The proposed antenna system has a cylindrical dielectric resonator antenna with a height of 9 mm and a radius of 6.35 mm as a radiating element.The proposed dielectric resonator antenna is sourced with a slot while the slot is excited with a rectangular microstrip transmission line.The microstrip transmission line is designed for a 50impedance to provide maximum power to the slot.As a result,the proposed antenna operates at 5.15 GHz with a 10-dB absolute bandwidth of 430 MHz(4.98–5.41 GHz).It is important to mention that the gain of the dielectric resonator antenna is enhanced by the introduction of an electromagnetic bandgap(EBG)structure.In fact,EBG units are placed below the antenna,which enhances the realized peak gain from 5.32 dBi to 8.36 dBi at 5.15 GHz.More specifically,a gain enhancement of 3.04 dB is observed with the introduction of the EBG array.This antenna has several good features such as high gain,compact size,large bandwidth,and lower losses which make it a suitable choice for long-range wireless communication systems.展开更多
A 16×16 micro-strip antenna array with high gain characteristic was proposed for the 5.5 GHz WiMAX application. The T-junctions with a power ratio of 2∶1 were used to design the feed network. To correct the step...A 16×16 micro-strip antenna array with high gain characteristic was proposed for the 5.5 GHz WiMAX application. The T-junctions with a power ratio of 2∶1 were used to design the feed network. To correct the stepped discontinuity of impedance change in common multi-section impedance transformer, exponential line matching transformers were adopted in the WiMAX frequency band. The reflection coefficient was lower than-15 dB from 5.08 GHz to 5.87 GHz. The measured gain of the antenna array achieved 29.8 dBi on E-plane at 5.8 GHz.展开更多
A printed TEM horn antenna with high gain fed by balanced microstrip line is proposed. The radiation part of the antenna consists of two symmetrical triangular metal slice branches printed on the FR-4 substrate with 1...A printed TEM horn antenna with high gain fed by balanced microstrip line is proposed. The radiation part of the antenna consists of two symmetrical triangular metal slice branches printed on the FR-4 substrate with 15 mm thickness. The two branches are fed by balanced microstrip line. The antenna is simulated by software CST MICROWAVE STUDIO and the equivalent adopted dipole model is proposed to describe the radiation characteristic of the antenna. The simulation results indicate that the frequency range is from 164 GHz to 5 GHz with reflection coefficient less than -6 dB, and the typical gain value is 8 dB in the operating bandwidth. In order to improve antenna gain without influencing the bandwidth, the length of the dielectric slab should be extended appropriately in the main radiation direction. By extending the length of the dielectric slab appropriately in the main radiation direction, the antenna gain can be improved significantly without the influence on the bandwidth. Besides, a metal disc loaded in the radiation direction makes the gain in band be more stable. The prototype has been fabricated and measured in microwave anechoic chamber which is coincident with the simulation results. This antenna can be widely applied in the UWB field.展开更多
A novel three layers microstrip antenna element that has the advantages of wideband and high-gain is proposed. The eigenvalue equation and the frequency characteristic formulas of the input Voltage Stand Wave Ratio ( ...A novel three layers microstrip antenna element that has the advantages of wideband and high-gain is proposed. The eigenvalue equation and the frequency characteristic formulas of the input Voltage Stand Wave Ratio ( VSWR ) are obtained by using the spectral domain method and equivalent circuit method, respectively. With the aid of the numerical results, a C-band microstrip antenna element with bandwidth of 16% (VSWR【1.5) or 25% (VSWR【2) and gain of 10.2-11.3 dB is developed, which are much larger than the bandwidth of 5-6% and the gain of 6-7 dB of the common microstrip antenna element.展开更多
Antenna array gain is a relative measure of performance defined differently in various literature. Most definitions of gain are not power consistent, and thus cannot be used directly in link budget analysis. In this s...Antenna array gain is a relative measure of performance defined differently in various literature. Most definitions of gain are not power consistent, and thus cannot be used directly in link budget analysis. In this short paper, we present a power correction factor for common definitions of power gain of antenna arrays that allows them to be used in standard link budget calculations.展开更多
文摘Antennas are an indispensable element in wireless networks. For long-distance wireless communication, antenna gains need to be very strong (highly directive) because the signal from the antenna loses a lot of strength as it travels over long distances. This is true in the military with missile, radar, and satellite systems, etc. Antenna arrays are commonly employed to focus electromagnetic waves in a certain direction that cannot be achieved perfectly with a single-element antenna. The goal of this study is to design a rectangular microstrip high-gain 2 × 1 array antenna using ADS Momentum. This microstrip patch array design makes use of the RT-DUROID 5880 as a substrate with a dielectric constant of 2.2, substrate height of 1.588 mm, and tangent loss of 0.001. To achieve efficient gain and return loss characteristics for the proposed array antenna, RT-Duroid is a good choice of dielectric material. The designed array antenna is made up of two rectangular patches, which have a resonance frequency of 3.3 GHz. These rectangular patches are excited by microstrip feed lines with 13 mm lengths and 4.8 mm widths. The impedance of the patches is perfectly matched by these transmission lines, which helps to get better antenna characteristics. At a resonance frequency of 3.3 GHz, the suggested antenna array has a directivity of 10.50 dB and a maximum gain of 9.90 dB in the S-band. The S parameters, 3D radiation pattern, directivity, gain, and efficiency of the constructed array antenna are all available in ADS Momentum.
文摘This paper demonstrates the analysis of antenna pattern and gain for different designs of full-wave dipole antenna feeding techniques. Seven such techniques were studied and analyzed;symmetrical dual feeding in phase, symmetrical dual feeding out of phase, asymmetrical dual feeding in phase, asymmetrical dual feeding out of phase, symmetrical triple feeding in phase and symmetrical triple feeding out of phase. Symmetrical dual feeding in phase produced high gain as compared to the single and center-fed antennas. An improvement of about 3 to 3.5 dB was achieved comparing to center tap fed and off center fed. It was found that an asymmetrical dual feeding in-phase provides good performance, considering the directivity, pattern, and input impedance. A 2.46 dB gain has been attained. It was found that a symmetrical triple feeding provides an overall best performance with respect to gain, radiation pattern, beam width and input impedance.
文摘A rectangular microstrip patch antenna using conventional Poly Tetra Fluride Ethelene (PTFE) substrate with air cavity is proposed and theoretically investigated. Considerably high gain along with improved front to back radiation isolation is demonstrated using such proposed antenna. The radiation performance of this new antenna has been compared to a conventional microstrip patch for some commonly used aspect ratios (width to length ratio). Compared to conventional microstrip antenna the proposed configuration shows more than 12% increment in peak gain and more than 10% increment in front to back radiation performance in each set of aspect ratio. The elucidation of such improvement in the radiation characteristics of the proposed antenna is also presented.
基金This work was supported by an Institute for Information and Communications Technology Promotion(IITP),funded by the Korea government(MSIP)(No.2021-0-00490,Devel-opment of precision analysis and imaging technology for biological radio waves).
文摘This paper presents the design of wideband and high gainFrequency Selective Surface(FSS)loaded antenna for ultra-wideband(UWB)wireless applications requiring high-gain.The antenna consists of a monopole and an FSS reflector.Initially,a conventional rectangular monopole antenna is modified using slot and stub to achieve wide operational bandwidth and size reduction.This modified antenna shows 50%miniaturization compared to a primary rectangular monopole,having a wide impedance bandwidth of 3.6-11.8 GHz.Afterward,an FSS is constructed by the combination of circular and square ring structures.The FSS array consisting of 8×8-unit cells are integrated with the antenna as a reflector to enhance the performance of the proposed miniaturized UWB antenna.The loading of FSS results in an improvement of at least 4 dBi gain in the entire operational bandwidth.Moreover,the antenna’s bandwidth is also increased at the lower frequency band due to the presence of the FSS.A prototype of the antenna is fabricated and tested to verify the simulation results.The simulation and measurement results show that the antenna offers a wideband-10 dB impedance bandwidth ranging from 2.55-13GHz with a stable peak gain of 8.6 dBi and retains the radiation pattern stability.
基金The author would like to thank the Deanship of Scientific Research at Majmaah Universty,Kingdom of Saudi Arabia for supporting this work(R-2021-211).
文摘High gain antennas are highly desirable for long-range wireless communication systems.In this paper,a compact,low profile,and high gain dielectric resonator antenna is proposed,fabricated,experimentally tested,and verified.The proposed antenna system has a cylindrical dielectric resonator antenna with a height of 9 mm and a radius of 6.35 mm as a radiating element.The proposed dielectric resonator antenna is sourced with a slot while the slot is excited with a rectangular microstrip transmission line.The microstrip transmission line is designed for a 50impedance to provide maximum power to the slot.As a result,the proposed antenna operates at 5.15 GHz with a 10-dB absolute bandwidth of 430 MHz(4.98–5.41 GHz).It is important to mention that the gain of the dielectric resonator antenna is enhanced by the introduction of an electromagnetic bandgap(EBG)structure.In fact,EBG units are placed below the antenna,which enhances the realized peak gain from 5.32 dBi to 8.36 dBi at 5.15 GHz.More specifically,a gain enhancement of 3.04 dB is observed with the introduction of the EBG array.This antenna has several good features such as high gain,compact size,large bandwidth,and lower losses which make it a suitable choice for long-range wireless communication systems.
基金Supported by the National Natural Science Foundation of China(No.60777014)the Specialized Research Fund for the Doctoral Program of Higher Education of China(No.20090032110027)
文摘A 16×16 micro-strip antenna array with high gain characteristic was proposed for the 5.5 GHz WiMAX application. The T-junctions with a power ratio of 2∶1 were used to design the feed network. To correct the stepped discontinuity of impedance change in common multi-section impedance transformer, exponential line matching transformers were adopted in the WiMAX frequency band. The reflection coefficient was lower than-15 dB from 5.08 GHz to 5.87 GHz. The measured gain of the antenna array achieved 29.8 dBi on E-plane at 5.8 GHz.
基金Sponsored by the Fundamental Research Funds for the Central Universities (Grant No. HIT. NSRIF. 2010096)the Heilongjiang Post-doctorial Financial Assistance (Grant No. LBH-Z09187)
文摘A printed TEM horn antenna with high gain fed by balanced microstrip line is proposed. The radiation part of the antenna consists of two symmetrical triangular metal slice branches printed on the FR-4 substrate with 15 mm thickness. The two branches are fed by balanced microstrip line. The antenna is simulated by software CST MICROWAVE STUDIO and the equivalent adopted dipole model is proposed to describe the radiation characteristic of the antenna. The simulation results indicate that the frequency range is from 164 GHz to 5 GHz with reflection coefficient less than -6 dB, and the typical gain value is 8 dB in the operating bandwidth. In order to improve antenna gain without influencing the bandwidth, the length of the dielectric slab should be extended appropriately in the main radiation direction. By extending the length of the dielectric slab appropriately in the main radiation direction, the antenna gain can be improved significantly without the influence on the bandwidth. Besides, a metal disc loaded in the radiation direction makes the gain in band be more stable. The prototype has been fabricated and measured in microwave anechoic chamber which is coincident with the simulation results. This antenna can be widely applied in the UWB field.
文摘A novel three layers microstrip antenna element that has the advantages of wideband and high-gain is proposed. The eigenvalue equation and the frequency characteristic formulas of the input Voltage Stand Wave Ratio ( VSWR ) are obtained by using the spectral domain method and equivalent circuit method, respectively. With the aid of the numerical results, a C-band microstrip antenna element with bandwidth of 16% (VSWR【1.5) or 25% (VSWR【2) and gain of 10.2-11.3 dB is developed, which are much larger than the bandwidth of 5-6% and the gain of 6-7 dB of the common microstrip antenna element.
文摘Antenna array gain is a relative measure of performance defined differently in various literature. Most definitions of gain are not power consistent, and thus cannot be used directly in link budget analysis. In this short paper, we present a power correction factor for common definitions of power gain of antenna arrays that allows them to be used in standard link budget calculations.