Mutual coupling suppression of aperture coupled microstrip antenna array

A mutual coupling suppression method is proposed for microstrip antenna array by cutting four small semi-circle annular apertures on the metal plate. The structure of antenna array is composed of 2 × 2 four elements. The antenna consists of double layer dielectric, and it realizes circular polarization characteristics by cutting rectangular slot on circular patch in the direction of 45°, by using aperture coupling feeding and reverse feeding principle. There is 90＊ phase difference between adjacent antenna elements. Thus, it cuts off the coupling current field between the elements, suppresses the surface wave and reduces the mutual coupling by cutting four semi-circle annular apertures symmetrically on the metal plate. The simulation results show that after cutting four semi-circle annular apertures, the antenna array coupling coefficients decrease significantly, and the side and back lobe levels are suppressed effectively with the gain of antenna improved. So the proposed method is effective to suppress microstrip antenna array mutual coupling.

A New Dual Polarized Aperture-Coupled Printed Array for SAR Applications

This paper presents a new design of dual polarized aperture coupled printed antenna array. The finite difference time domain (FDTD) analysis of an aperture coupled microstrip element is performed, and the effects of antenna parameters on its characteristics are obtained to guide the design of the printed array. Then an 8×2 dual polarized array design in X band is introduced with configuration plots. In order to improve its isolation and cross polarization, an outphase displacement feeding technique is adopted in the feed network. Also, the round bends are used instead of conventional right angle bends so as to achieve better VSWR performance. Experimental results are presented, indicating the validity of the design. This dual polarized array can be applied as a sub array of spaceborne SAR systems.

Ultra-Wideband Annular Ring Fed Rectangular Dielectric Resonator Antenna for Millimeter Wave 5G Applications

In this article an ultra-wideband rectangular Dielectric Resonator Antenna is designed for millimeter wave 5G frequency band applications.Indoor 5G communications require antenna system with wide bandwidth and high efficiency to enhance the throughput in the channel.To fulfill such requirements a Dielectric Resonator Antenna(DRA)is designed here which has achieved an ultra-wide bandwidth of 20.15%(22.32–27.56 GHz)which is 5.24 GHz of bandwidth centered at 26 GHz as resonating frequency.This covers the complete band 30(24.3–27.5 GHz)of 5G spectrum.26 and 28 GHz are considered as most popular frequencies in millimeter wave 5G communications.The aperture fed DRA designed here has also achieved an efficiency of 96 percentage with maximum radiation in the broadside direction(Phi=0,Theta=0).The measured gain of the DRA is 6.3 dB.The DRA designed here has dimensions of 0.25λ0×0.22λ0×0.12λ0.under the characteristic’s mode.The DRA is placed over a substrate with dimensions 0.5λ0×0.5λ0×0.02λ0.A cross slot aperture has been made on the ground plane which is placed above to the substrate.Here a full ground plane is used to resonate the antenna and is of similar dimension to the substrate.A microstrip line with two concentric rings makes an annular feed structure is used to excite the DRA and is placed below the substrate.The DRA is excited here in characteristics mode TE1Y1 and is the only mode of excitation.The DRA is linearly polarized,and the characteristic mode of excitation is maintained with 50 Ohm input impedance of the antenna.The DRA also gives here a good difference between the co-pol and cross pol approximately 15 to 20 dB.This antenna is more suitable for 5G indoor applications in millimeter wave frequency band centered at 26 GHz.

Optimal design on wideband directional coupler

Combining the modified Bethe small holes coupling theory with McDonald thickness theory and field averaging correction factor, it is accurate to design the weak coupling waveguide directional coupler. While the coupling is tight, the decrease of the field strength in the main waveguide caused by aperture should not be neglected. For a -6 dB directional coupler is described in this article, the theoretical value of coupling is good agree to the simulation value, by simulated and optimized with the professional software computer simulation technology （CST）. In the designed waveband, the error of coupling between theoretical value and simulating one is less than 0.25 dB. The error of coupling between simulation value and designed value is less than 0.5 dB. To improve the isolation, some spaces between two adjacent holes are turned from the traditional 1/4 centre guided wavelength. The performance of isolation has 5 dB improvement, and length of the coupling area is only 51.06 mm.