Performance Characterization of CR/PU Asphalt for Potential Application in Assembled Fast-Repairing Engineering

Conventional repairing methods for asphalt pavement have some inconveniences,such as insufficient strength,and are typically time-consuming.To address these issues,this study proposes a new technological method to design and prepare a high-performance assembled asphalt concrete block for fast repair of the potholes.A series of composite modified asphalt binders with 10%crumb rubber(CR)and different dosages(0%,1%,3%,5%)of polyurethane(PU)are examined to determine the optimized binder.Subsequently,the corresponding asphalt mixtures are prepared for further comparison and assessment of engineering properties,such as moistureinduced damage,high-temperature deformation,and low-temperature cracking characteristics.The test results show that PU can significantly improve the high-temperature performance and hardness of(crumb rubber modified asphalt)CRMA binder;3%PU contributes allowing the resistance of CRMA mixture to moisture-induced damage at higher levels,particularly under water whole immersion;as 3%PU is added,the high-temperature rutting deformation resistance of the CRMA mixture increases significantly,and the low-temperature anti-cracking properties are also improved slightly.Therefore,the innovatively designed high-quality assembled fast-repairing asphalt concrete block is recommended as an appropriate option for highway maintenance.

Fatigue Resistance of RCA Modified Asphalt Based on Dielectric Properties

In order to study the anti-fatigue performance of RCA modified asphalt (RMA),the performance of RMA and 90#matrix asphalt with different modifier content were measured by asphalt penetration,ductility,softening point,Brookfield viscosity,rheological index,infrared spectrum and dielectric constant test.This paper discusses the changes of asphalt basic indexes,fatigue properties and asphalt components based on dielectric properties under different modifier contents,and analyzes the grey correlation degree between components and asphalt pavement performance indexes.The results show that the optimum content of RCA modifier is 16.7%of the asphalt quality according to the penetration,ductility,softening point,Brockfield viscosity,viscosity temperature curve and fatigue life.In the phase angle-strain curve,there is disorder in the latter part of the curve.According to the strain (ε_(d)) corresponding to the disorder point,a new fatigue failure criterion is proposed and proved.Based on the new asphalt fatigue failure criterion,the fatigue prediction model of asphalt mixture is improved,and the fatigue life predicted by the improved fatigue model is compared with the fatigue life obtained by four-point bending fatigue test.The results show that the proposed new asphalt fatigue failure criterion is reasonable,and the fatigue life predicted by the improved asphalt mixture fatigue prediction model is accurate.The research method of classifying asphalt components based on dielectric properties is simple and effective,and the components have a high correlation with the road performance of base asphalt and modified asphalt.

Damage Mechanism of Ultra-thin Asphalt Overlay(UTAO) based on Discrete Element Method

Aiming to analyze the damage mechanism of UTAO from the perspective of meso-mechanical mechanism using discrete element method(DEM),we conducted study of diseases problems of UTAO in several provinces in China,and found that aggregate spalling was one of the main disease types of UTAO.A discrete element model of UTAO pavement structure was constructed to explore the meso-mechanical mechanism of UTAO damage under the influence of layer thickness,gradation,and bonding modulus.The experimental results show that,as the thickness of UTAO decreasing,the maximum value and the mean value of the contact force between all aggregate particles gradually increase,which leads to aggregates more prone to spalling.Compared with OGFC-5 UTAO,AC-5 UTAO presents smaller maximum and average values of all contact forces,and the loading pressure in AC-5 UTAO is fully diffused in the lateral direction.In addition,the increment of pavement modulus strengthens the overall force of aggregate particles inside UTAO,resulting in aggregate particles peeling off more easily.The increase of bonding modulus changes the position where the maximum value of the tangential force appears,whereas has no effect on the normal force.

Laboratory Evaluation of Performance Recovery of Aged SBS-modified Asphalt Using Regenerants with Different Base Oil Components

In this study,the regenerative effects of different regenerants on aged SBS-modified asphalt from different perspectives were investigated,including their conventional properties,viscoelastic behavior,creep-related properties,and micromorphology.Base oils composed of different proportions of aromatic and saturated hydrocarbons as well as the styrene-butadiene-styrene(SBS)restorer were used to prepare the regenerants.The results showed that the components of the base oil of the regenerant played a crucial role in determining the characteristics and performance of the recycled SBSmodified asphalt.Regenerants containing a high proportion of aromatics dissolved the hard segment in the SBS restorer,thereby delaying the effect of a reduction in the regenerants on the performance of the aged asphalts at a high temperature.Regenerants containing a high proportion of saturates dissolved the soft segment in the SBS restorer to enhance the lowtemperature performance of the recycled asphalts.In addition,the stress sensitivity of the recycled asphalts increased with the fraction of aromatics in the regenerant.As the aromatic content of the base oil components of the regenerants increased and their saturate content decreased,the state of dispersion of the SBS phase in the recycled SBS-modified asphalts improved.The optimal content of aromatics in the base oil of the regenerants should be set in the range of 33%to 47%to ensure the adequate performance of the recycled asphalts and a high efficiency of the SBS restorer.

Multiscale Study on Low Temperature Crack Resistance Mechanism of Steel Slag Asphalt Mixture

The objective of this paper was to study low temperature crack resistance mechanism of steel slag asphalt mixture(SAM).Thermal stress restrained specimen test(TSRST)and three-point bending test were carried out to evaluate the low-temperature crack resistance of SAM and basalt asphalt mixture(BAM).Based on the digital image correlation technique(DIC),the strain field distribution and crack propagation of SAM were analyzed from the microscopic point of view,and a new index,crack length factor(C),was proposed to evaluate the crack resistance of the asphalt mixture.The crystal phase composition and microstructure of steel slag aggregate(SA)and basalt aggregate(BA)were studied by X-ray diffraction(XRD)and scanning electron microscopy(SEM)to explore the low-temperature crack resistance mechanism of SAM.Results show that the low-temperature crack resistance of SAM is better than that of BAM;SAM has good integrity and persistent elastic deformation,and its bending failure mode is a hysteretic quasi-brittle failure;The SA surface is evenly distributed with pores and has surface roughness.SA has the composition phase of alkaline aggregate-calcite(CaCO3),so it has good adhesion to asphalt,which reveals the mechanism of excellent low-temperature crack resistance of SAM.

Preparation and Analysis of Carbon Fiber-Silicon Carbide Thermally Conductive Asphalt Concrete

An experimental investigation into the thermal conductivity of CF-SiC two-phase composite asphalt concrete is presented.The main objective of this study was to verify the possibility of using SiC powder instead of mineral powder as the thermal conductive filler to prepare a new type of asphalt concrete and improve the efficiency of electrothermal snow and ice melting systems accordingly.The thermal conductivity of asphalt concrete prepared with different thermally conductive fillers was tested by a transient plane source method,and the related performances were measured.Then the temperature rise rate and surface temperature were studied through field heating tests.Finally,the actual ice melting efficiency of the thermally conductive asphalt concrete was evaluated using an effective electrothermal system.As shown by the experimental results,the composite made of SiC powder and carbon fiber has a high thermal conductivity.When SiC replaces mineral powder,the thermal conductivity of the asphalt mixture increases first and then decreases with the increase of carbon fiber content.In the present study,in particular,the thermal conductivity attained a peak when the carbon fiber content was 0.2%of the aggregate mass.

Enhanced asphalt dynamic modulus prediction: A detailed analysis of artificial hummingbird algorithm-optimised boosted trees

This study introduces and evaluates a novel artificial hummingbird algorithm-optimised boosted tree(AHAboosted)model for predicting the dynamic modulus(E*)of hot mix asphalt concrete.Using a substantial dataset from NCHRP Report-547,the model was trained and rigorously tested.Performance metrics,specifically RMSE,MAE,and R2,were employed to assess the model's predictive accuracy,robustness,and generalisability.When benchmarked against well-established models like support vector machines(SVM)and gaussian process regression(GPR),the AHA-boosted model demonstrated enhanced performance.It achieved R2 values of 0.997 in training and 0.974 in testing,using the traditional Witczak NCHRP 1-40D model inputs.Incorporating features such as test temperature,frequency,and asphalt content led to a 1.23%increase in the test R2,signifying an improvement in the model's accuracy.The study also explored feature importance and sensitivity through SHAP and permutation importance plots,highlighting binder complex modulus|G*|as a key predictor.Although the AHA-boosted model shows promise,a slight decrease in R2 from training to testing indicates a need for further validation.Overall,this study confirms the AHA-boosted model as a highly accurate and robust tool for predicting the dynamic modulus of hot mix asphalt concrete,making it a valuable asset for pavement engineering.

Progression of e-ticketing implementation for state transportation agencies for asphalt materials

E-ticketing,which has been promoted by the Federal Highway Administration(FHWA)“every day counts”(EDC)initiative,utilizes software applications to digitally track and store information regarding highway construction materials paid by state transportation agencies(STAs)by weight in unit bid contract structures.STAs often face implementation barriers such as institutional inertia,or the resistance by stakeholders to adopt changes from the status quo,including new technologies.The purpose of this paper is to determine the progression of STA e-ticketing policy adoption,specifically with a focus on asphalt paving operations,due to the COVID-19 pandemic.To accomplish this research effort,previous FHWA data,National Cooperative Highway Research Program(NCHRP)data,and other literatures are reviewed to determine an implementation baseline.Additional data is collected from the American Association of State Highway and Transportation Officials Committee on Con-struction to gain current feedback from STAs and their highway contractor partners after the COVID-19 pandemic.Additionally,a case study featuring the Kentucky Transportation Cabinet(KYTC),the Kentucky Association of Highway Contractors(KAHC),and the Plantmix Asphalt Industry of Kentucky(PAIKY)is performed to provide more in-depth analysis.The major finding includes a statistically significant result indicating increased imple-mentation of e-ticketing for asphalt operations within the last two years,along with noting benefits including employee safety,task loading,and project documentation along with concerns regarding cellular connectivity and procurement responsibilities.These findings indicate the importance of STAs investing in partnership with con-tractors to improve stakeholder buy-in before proceeding towards e-ticketing adoption.

Long-term performance of recycled asphalt mixtures containing high RAP and RAS

The application of reclaimed asphalt pavement(RAP)and reclaimed asphalt shingles(RAS)on asphalt pavement can reduce the asphalt paving cost,conserve energy and protect the environment.However,the use of high contents of RAP and RAS in asphalt pavement may lead to durability issues,especially the fatigue cracking and thermal cracking.It is necessary to conduct a series of analyses on asphalt mixtures containing high RAP and RAS,and seek methods to enhance their long-term performance.This paper provides a comprehensive over-view of the long-term performance of recycled asphalt mixtures containing high contents of RAP and RAS.The findings in this research show that rutting resistance of high recycled asphalt mixtures is not a concern,whereas their resistance to fatigue and thermal cracking is not conclusive.Recycling agents can be used to improve the thermal cracking resistance of high recycled asphalt mixtures.An optimum decision on recycling agents will improve the durability properties of high recycled asphalt mixtures.It is recommended that to use a balanced mixture design approach with testing of the blended asphalt binders will provide better understanding of long-term performance of recycled asphalt mixtures containing high RAP and RAS.

The Effectiveness of the Havriliak-Negami Model in Predicting the Master Curves of the Asphalt Blends with SBS Triblock Copolymer and Organic-Montmorillonite at Different Temperatures and Frequencies

The dynamic viscoelastic properties of asphalt AC-20 and its composites with Organic-Montmorillonite clay (OMMt) and SBS were modeled using the empirical Havriliak-Negami (HN) model, based on linear viscoelastic theory (LVE). The HN parameters, α, β, G0, G∞and τHN were determined by solving the HN equation across various temperatures and frequencies. The HN model successfully predicted the rheological behavior of the asphalt and its blends within the temperature range of 25˚C - 40˚C. However, deviations occurred between 40˚C - 75˚C, where the glass transition temperature Tg of the asphalt components and the SBS polymer are located, rendering the HN model ineffective for predicting the dynamic viscoelastic properties of composites containing OMMt under these conditions. Yet, the prediction error of the HN model dropped to 2.28% - 2.81% for asphalt and its mixtures at 100˚C, a temperature exceeding the Tg values of both polymer and asphalt, where the mixtures exhibited a liquid-like behavior. The exponent α and the relaxation time increased with temperature across all systems. Incorporating OMMt clay into the asphalt blends significantly enhanced the relaxation dynamics of the resulting composites.

Study on the Effect of Fibers on the Properties of Asphalt Mastics

To study the influence of fiber on the properties of asphalt mortar,the properties of lignin fiber,polyester fiber,and basalt fiber were summarized and analyzed respectively.The high-and low-temperature properties of fiber asphalt mortar were studied and analyzed by using three indexes,rutting factor and tensile fracture energy.The results showed that all three kinds of fibers could improve the performance of asphalt mortar to varying degrees,with lignin fiber demonstrating the best effect,followed by basalt fiber and polyester fiber.The type the fiber can be selected based on the required thermal stability and cost depending on the project type.

On the Use of Recycled Asphalt and Trinidad Lake Asphalt(TLA)for the Preparation of High Modulus Asphalt Concrete

Rutting of asphalt pavement occurs earlier and is more serious under the increasingly heavy traffic load conditions that can be found in subtropical monsoon climate regions.High modulus asphalt concrete(HMAC)with excellent anti-rutting and anti-fatigue properties is generally used to mitigate this issue.Given the relatively high cost of the additives used in this type of asphalt,in this study the feasibility of using recycled asphalt mixture(RAP)and Trinidad lake asphalt(TLA)for the preparation of HMAC is considered.The mineral composition of the RAP is first analyzed,then the TLA modified asphalt with different levels of RAP content is used to assess the effect of RAP on the performance of the mixture.Finally,the high-temperature rheological properties of extracted bitumen and the adhesion characteristic between mineral and bitumen are analyzed.The results show that after RAP combustion,the yellowish and greyish minerals display different alkalinity values,while the greyish mineral exhibits an improved ability to combine with bitumen.Thus,RAP can significantly enhance the high-temperature rutting resistance of TLA modified asphalt mixtures.The aged bitumen in RAP makes the mixed binder harder and improves its rheological properties at high temperatures.

Effects of Filler-Asphalt Ratio on the Properties of Lignin and Polyester Fiber Reinforced SMPU/SBS Modified Asphalt Mortar

To understand the effects offiller-asphalt ratio on different properties of lignin and polyesterfiber reinforced shape memory polyurethane(SMPU)/styrene butadiene styrene(SBS)composite modified asphalt mortar(PSAM),as well as to reveal the reinforcing and toughening mechanisms of lignin and polyesterfibers on PSAM,SMPU,SBS and mineral powder werefirst utilized to prepare PSAM.Then the conventional,rheological and anti-cracking properties of ligninfiber reinforced PSAM(LFAM)and polyesterfiber reinforced PSAM(PFAM)at dif-ferentfiller-asphalt ratios were characterized.Test results indicate that the shear strength,deformation resistance and viscosity are increased after adding 0.8wt%ligninfiber or polyesterfiber and increasing thefiller-asphalt ratio from 0.8 to 1.2.The optimalfiller-asphalt ratio of 1.0 is proposed after comprehensive performance assessments of PSAM.Polyesterfiber shows a better reinforcing effect than ligninfiber,but its improvement in the thermal stability of PSAM is not significant at high temperatures.Additionally,the complex modulus,storage modulus,loss modulus and rutting resistance factor of PSAM are improved after adding ligninfiber and polyesterfiber,as well as show an increasing trend as thefiller-asphalt ratio is raised,but the phase angle is gradually decreased.Further,the increase of elastic components in PSAM effectively enhances the anti-deformation ability of PSAM at high temperatures,and polyesterfiber more obviously improves the high-temperature deformation resistance of PSAM than ligninfiber.Finally,the anti-cracking performance of PFAM and LFAM at low temperatures is reduced by 74.2%and 46.7%,respectively,as thefiller-asphalt ratio is raised from 0.8 to 1.2.The low-temperature anti-cracking performance of LFAM is lower than that of PFAM at the samefiller-asphalt ratio,even lower than that of PSA.Compared with ligninfiber,the anti-cracking performance and deformation resistance of PSAM at low temperature is more greatly enhanced by polyester fiber.

Research Progress of Epoxy Asphalt Material for Roads

Asphalt is a semi-solid or solid mixture formed by hydrocarbons and non-metallic elements.It is widely applied in the fields of building waterproofing and road paving.Asphalt is a low noise,durable,and renewable pavement material.However,asphalt materials have some shortcomings such as liquefying at high temperatures and brittleness at low temperatures,which are less adaptable to different environments.Therefore,people have gradually shifted their focus to asphalt modification.This paper presents an in-depth analysis and research on the composition,structure,and performance of epoxy asphalt materials for roads,so that this material can be widely used.

A comprehensive review on polyurethane modified asphalt: Mechanism, characterization and prospect

Polyurethane(PU),with excellent physical and chemical properties and high designability,is one of the ideal materials for asphalt modification in the future.In this paper,based on the limitations of traditional asphalt modifiers,the preparation process,relative advantages and development prospects of PU as asphalt modifiers are described.Subsequently,the spatial structure,physical and chemical properties of PU synthetic raw materials were combined with the modification properties of PU to analyze the effect and influence of PU on asphalt modification.Specifically,polyurethane modified asphalt(PUMA)is divided into thermoplastic polyurethane modified asphalt(TP-PUMA)and thermosetting polyurethane modified asphalt(TS-PUMA).The gain effect of TPPUMA in high-temperature performance,low-temperature performance,aging resistance,fatigue resistance,weathering performance and bonding performance is obvious.In addition,it has good storage stability.With excellent road performance,TS-PUMA makes up for the shortcomings of epoxy asphalt in terms of lowtemperature performance and compatibility.Finally,due to the development trend of functional diversification of modified asphalt,the research basis and status of several new modified asphalts based on PU properties are described.Because the systematic study of PUMA is insufficient,this paper proposes corresponding research.To provide guidance and ideas for the research of PU modified asphalt.

Materials,preparation,performances and mechanism of polyurethane modified asphalt and its mixture:A systematic review

With the rapid development of asphalt pavement technology,it has attracted considerable attention to improving the durability of asphalt pavement.An effective action is to use modified asphalt with high performance and durability.Polyurethane(PU)has been used in asphalt pavement engineering to enhance the durability and service life of asphalt pavement because of its excellent high-temperature performance,toughness,wear resistance,aging resistance and oil resistance.However,PU modified asphalt technology is still in the exploratory stage.The preparation,modification mechanism and working performances of PU modified asphalt need to be further clarified.Therefore,this paper summarized the research progress of PU modified asphalt and its mixture.The composition of PU modified asphalt was introduced.The addition methods of PU materials and preparation process parameters of the PU modified asphalt were determined.The modification mechanism of PU on asphalt was discussed.The effects of polyurethane on asphalt were analyzed and the road performances of its mixture were evaluated.Finally,the development tendency towards PU modified asphalt and its mixture were forecasted.

Normalized fatigue properties of asphalt mixture at various temperatures

This study normalized the mixture's fatigue behavior at various temperatures,and the strength and fatigue tests of the mixture were conducted.The stress state of the asphalt mixture includes direct tensile,uniaxial compression,and indirect tensile.The Desai yield surface and fatigue path were proposed.And a normalized fatigue characteristics model of the mixture was established.The following conclusions were obtained.With the increases in the loading rate,the strength of the asphalt mixture increased.As the temperature increases,the strength of the mixture is reduced.At various temperatures and rates,the strength forms a closed curved surface.The Desai strength yield surface was established,which forms a closed curved surface.When the loading rate and temperature are below a certain critical line,the asphalt mixture will not undergo strength damage.At a fixed stress state,the fatigue damage path of the mixture was determined.The stress ratio was determined considering the influence of the loading rate.In this way,a normalized model can be described to express the asphalt mixture fatigue properties at various temperatures and stress levels.For the asphalt mixture in an indirect tensile state,the normalized fatigue equation parameter is 4.09.This model is more suitable for reflecting the viscous-elastic behavior of the mixtures than the fatigue equation determined by the notional stress ratio.

Review of emulsified asphalt modification mechanisms and performance influencing factors

In recent years,with the improvement of the requirements of road performance,modified emulsified asphalts with better performance has gradually replaced the emulsified asphalt and become the primary material for road maintenance.This paper introduces the modified emulsified asphalt materials commonly used in pavement maintenance projects,definitions and modified mechanisms of polymerized styrene butadiene rubber(SBR)modified emulsified asphalt,styrene butadiene styrene block polymer(SBS)modified emulsified asphalt and waterborne epoxy resin(WER)modified emulsified asphalt are summarized.The analysis focused on comparing the effects of modifiers,preparation process,auxiliary additives,and other factors on the performance of modified emulsified asphalt.In this paper,it is considered that the greatest impact on the performance of emulsified asphalt is the modifier,emulsifier mainly affects the speed of breaking the emulsion,stabilizers on the basic performance of emulsified asphalt evaporative residue is small;and when the modifier is distributed in the asphalt in a network,the dosage at this time is the recommended optimum dosage.Finally,this study recommends that in the future,the polymer-asphalt compatibility can be improved through composite modification,chemical grafting and other methods to continue to develop broader applicability and better performance of modified emulsified asphalt.

A review on evaluation of crack resistance of asphalt mixture by semi-circular bending test

Although there are many kinds of fracture tests to choose from in evaluating the crack resistance of asphalt mixture,the semi-circular bending(SCB)test has attracted a lot of attention in the academic road engineering community because of its simplicity,stability,and flexibility in testing and evaluation.The SCB test has become a common method to study the cracking resistance of asphalt mixture in recent years.This paper mainly summarizes the overview of the SCB test,summarizes some research results and common characterization parameters of the SCB test method in monotone test and fatigue test in recent years,and predicts and suggests the research direction of the SCB test in the future.It is found that the research on the monotonic SCB test is more comprehensive,and the research on the SCB fatigue test needs to be further improved in the aspects of loading mode,characterization parameter selection,and so on.Researchers can flexibly adjust the geometric dimensions and the test parameters of semi-cylindrical specimens,and conduct comprehensive analysis combined with the results of numerical simulation.The crack resistance of asphalt mixture can be comprehensively evaluated by fracture energy,fracture toughness,stiffness,flexibility index and other fracture indicators,combined with the crack propagation of the specimen.The analysis of numerical simulation can confirm the test results.In order to standardize the setting of fatigue parameters for future application,it is necessary to standardize the setting of bending performance.

Behavior Characteristics of Asphalt Components during the Process of Nano-cracks Temperature Self-healing

In order to investigate the behavior characteristics of asphalt components during the process of nano-cracks temperature self-healing(NTS),molecular simulation technology was used to simulate the temperature self-healing of asphalt.Based on the determination of asphalts(virgin asphalt and aged asphalt),the proportional changes of asphalt components were confirmed.The distribution characteristics of asphalt components were obtained by marking different components in the process of NTS.At the same time,the rationality of the micro simulation findings was confirmed by asphalt performance tests and infrared spectroscopy results.The results show that different asphalt components have different behavior characteristics in the process of NTS.The content of asphaltene and resin plays a key role in the process of NTS,while saturation and aromatics play an active role in the temperature self-healing before and after aging.The NTS is the result of the comprehensive action of different components,and the self-healing efficiency is proportional to the relative molecular mass.The effect of aging on the NTS is also realized by changing the proportion of asphalt components.