We examined the water adsorption and dissociation on ceria surfaces as well as ceria‐supported Au single‐atom catalysts using density functional theory calculations.Molecular and dissociative water were observed to ...We examined the water adsorption and dissociation on ceria surfaces as well as ceria‐supported Au single‐atom catalysts using density functional theory calculations.Molecular and dissociative water were observed to coexist on clean CeO2and reduced Au1/CeO2?x surfaces because of the small difference in adsorption energies,whereas the presence of dissociative water was highly favorable on reduced CeO2?x and clean Au1/CeO2surfaces.Positively charged Au single atoms on the ceria surface not only provided activation sites for water adsorption but also facilitated water dissociation by weakening the intramolecular O-H bonds.In contrast,negatively charged Au single atoms were not reactive for water adsorption because of the saturation of Au5d and6s electron shells.This work provides a fundamental understanding of the interaction between water and single‐atom Au catalysts.展开更多
气氛环境下原位研究催化剂的烧结行为,能够为理解催化剂在预处理以及反应条件下的烧结机理和高稳定催化剂的设计提供重要的实验依据。本文以Au/CeO_(2)模型纳米催化剂为研究对象,利用环境透射电子显微镜原位观察其在O_(2)与CO气氛下的...气氛环境下原位研究催化剂的烧结行为,能够为理解催化剂在预处理以及反应条件下的烧结机理和高稳定催化剂的设计提供重要的实验依据。本文以Au/CeO_(2)模型纳米催化剂为研究对象,利用环境透射电子显微镜原位观察其在O_(2)与CO气氛下的高温动态烧结过程。实验发现,负载在CeO_(2)上的Au纳米颗粒在O_(2)与CO气氛环境中表现出不同的烧结行为,其在O_(2)气氛下具有较高的烧结速度,同时存在颗粒迁移与聚集长大(particle migration and coalescence,PMC)和奥斯特瓦尔德熟化(Ostwald ripening,OR)两种烧结过程;在CO气氛下烧结速度较慢,烧结过程以OR为主。对比不同气氛环境下烧结后催化剂的表面结构可知,CO增加了CeO_(2)表面台阶的数量以及表面氧空位浓度,增强了载体对Au颗粒的锚定作用,从而提升Au/CeO_(2)催化剂的稳定性。展开更多
This work examines the influence of preparation methods on the physicochemical properties and catalytic performance of MnOx‐CeO2 catalysts for selective catalytic reduction of NO by NH3 (NH3‐SCR) at low temperature....This work examines the influence of preparation methods on the physicochemical properties and catalytic performance of MnOx‐CeO2 catalysts for selective catalytic reduction of NO by NH3 (NH3‐SCR) at low temperature. Five different methods, namely, mechanical mixing, impregnation,hydrothermal treatment, co‐precipitation, and a sol‐gel technique, were used to synthesizeMnOx‐CeO2 catalysts. The catalysts were characterized in detail, and an NH3‐SCR model reaction waschosen to evaluate the catalytic performance. The results showed that the preparation methodsaffected the catalytic performance in the order: hydrothermal treatment > sol‐gel > co‐precipitation> impregnation > mechanical mixing. This order correlated with the surface Ce3+ and Mn4+ content,oxygen vacancies and surface adsorbed oxygen species concentration, and the amount of acidic sitesand acidic strength. This trend is related to redox interactions between MnOx and CeO2. The catalystformed by a hydrothermal treatment exhibited excellent physicochemical properties, optimal catalyticperformance, and good H2O resistance in NH3‐SCR reaction. This was attributed to incorporationof Mnn+ into the CeO2 lattice to form a uniform ceria‐based solid solution (containing Mn‐O‐Cestructures). Strengthening of the electronic interactions between MnOx and CeO2, driven by thehigh‐temperature and high‐pressure conditions during the hydrothermal treatment also improved the catalyst characteristics. Thus, the hydrothermal treatment method is an efficient and environment‐friendly route to synthesizing low‐temperature denitrification (deNOx) catalysts.展开更多
CeO2 was synthesized via sol-gel process and used as supporter to prepare CuO/CeO2, Cu/CeO2 catalysts by impregnation method. The catalytic properties and characterization of CeO2, CuO/CeO2 and Cu/CeO2 catalysts were ...CeO2 was synthesized via sol-gel process and used as supporter to prepare CuO/CeO2, Cu/CeO2 catalysts by impregnation method. The catalytic properties and characterization of CeO2, CuO/CeO2 and Cu/CeO2 catalysts were examined by means of a microreactor-GC system, HRTEM, XRD, TPR and XPS techniques. The results show that CuO has not catalytic activity and the activity of CeO2 is quite low for CO oxidation. However, the catalytic activity of CuO/CeO2 and Cu/ CeO2 catalysts increases significantly. Furthermore, the activity of CuO/CeO2 is higher than that of Cu/CeO2 catalysts.展开更多
Reverse water gas shift (RWGS) reaction can serve as a pivotal stage in the CO2 conversion processes, which is vital for the utilization of CO2. In this study, RWGS reaction was performed over Pt/CeO2 catalysts at the...Reverse water gas shift (RWGS) reaction can serve as a pivotal stage in the CO2 conversion processes, which is vital for the utilization of CO2. In this study, RWGS reaction was performed over Pt/CeO2 catalysts at the temperature range of 200-500 degrees C under ambient pressure. Compared with pure CeO2, Pt/CeO2 catalysts exhibited superior RWGS activity at lower reaction temperature. Meanwhile, the calculated TOF and E-a values are approximately the same over these Pt/CeO2 catalysts pretreated under various calcination conditions, indicating that the RWGS reaction is not affected by the morphologies of anchored Pt nanoparticles or the primary crystallinity of CeO2. TPR and XPS results indicated that the incorporation of Pt promoted the reducibility of CeO2 support and remarkably increased the content of Ce 3 + sites on the catalyst surface. Furthermore, the CO TPSR-MS signal under the condition of pure CO2 flow over Pt/CeO 2 catalyst is far lower than that under the condition of adsorbed CO2 with H-2 -assisted flow, revealing that CO2 molecules adsorbed on Ce3+ active sites have difficult in generating CO directly. Meanwhile, the adsorbed CO2 with the assistance of H-2 can form formate species easily over Ce3+ active sites and then decompose into Ce3+-CO species for CO production, which was identified by in-situ FTIR. (C) 2016 Science Press and Dalian Institute of Chemical Physics, Chinese Academy of Sciences. Published by Elsevier B. V. and Science Press. All rights reserved.展开更多
Aqueous precipitation and deposition-precipitation method were used to prepare CeO2 supports and Au/CeO2 catalysts, respectively. The effect of preparation condition of support on the catalyst activity was investigate...Aqueous precipitation and deposition-precipitation method were used to prepare CeO2 supports and Au/CeO2 catalysts, respectively. The effect of preparation condition of support on the catalyst activity was investigated. The catalytic combustion of HCHO was considered as the probe reaction for comparing the catalyst activity. The BET, X-ray diffraction, X-ray photoelectron spectroscopy (XPS), and reduction (TPR) were carried out to analyze the influence factor on the catalysts activity. The results showed that the addition of dispersant and use of microwave in the support preparation procedure could be beneficial for enhancing the interaction of supports and gold species and thus improved the catalytic activity. The total conversion temperature for HCHO was 146 ℃ over AC400. With the modification during supports preparation process, the catalytic activity increased with total conversion temperature decreasing to 98 ℃. The results of XPS indicated that Au^0 and Au^+1 species coexisted in these catalysts and the activity of catalyst correlated with Au^+1/Au^0 ratio. Temperature-programmed reduction results demonstrated that the reduction peak appeared between 100-170 ℃ with the inducing of gold. The dependence of activity on the reduction peak temperature implied that ionic gold was catalytic activity component for HCHO oxidation.展开更多
The catalyst screening tests for carbon dioxide oxidative coupling of methane (CO2-OCM) have been investigated over ternary and binary metal oxide catalysts. The catalysts are prepared by doping MgO- and CeO2-based so...The catalyst screening tests for carbon dioxide oxidative coupling of methane (CO2-OCM) have been investigated over ternary and binary metal oxide catalysts. The catalysts are prepared by doping MgO- and CeO2-based solids with oxides from alkali (Li2O), alkaline earth (CaO), and transition metal groups (WO3 or MnO). The presence of the peroxide (O2-2) active sites on the Li2O2, revealed by Raman spectroscopy, may be the key factor in the enhanced performance of some of the Li2O/MgO catalysts. The high reducibility of the CeO2 catalyst, an important factor in the CO2-OCM catalyst activity, may be enhanced by the presence of manganese oxide species. The manganese oxide species increases oxygen mobility and oxygen vacancies in the CeO2 catalyst. Raman and Fourier Transform Infra Red (FT-IR) spectroscopies revealed the presence of lattice vibrations of metal-oxygen bondings and active sites in which the peaks corresponding to the bulk crystalline structures of Li2O, CaO, WO3 and MnO are detected. The performance of 5%MnO/15%CaO/CeO2 catalyst is the most potential among the CeO2-based catalysts, although lower than the 2%Li2O/MgO catalyst. The 2%Li2O/MgO catalyst showed the most promising C2+ hydrocarbons selectivity and yield at 98.0% and 5.7%, respectively.展开更多
CeO2-Co3O4 catalysts for low-temperature CO oxidation were prepared by a co-precipitation method. In combination with the characterization methods of N2 adsorption/desorption, XRD, temperature-programmed reduction (...CeO2-Co3O4 catalysts for low-temperature CO oxidation were prepared by a co-precipitation method. In combination with the characterization methods of N2 adsorption/desorption, XRD, temperature-programmed reduction (TPR), and FT-IR, the influence of the cerium content on the catalytic performance of CeO2-Co3O4 was investigated. The results indicate that the prepared CeO2-Co3O4 catalysts exhibit a better activity than that of pure CeO2 or pure Co3O4. The catalyst with the Ce/Co atomic ratio 1 : 16 exhibits the best activity, which converts 77% of CO at room temperature and completely oxidizes CO at 45 ℃.展开更多
The atomic structure of the active sites in Cu/CeO2 catalysts is intimately associated with the copper-ceria interaction. Both the shape of ceria and the loading of copper affect the chemical bonding of copper species...The atomic structure of the active sites in Cu/CeO2 catalysts is intimately associated with the copper-ceria interaction. Both the shape of ceria and the loading of copper affect the chemical bonding of copper species on ceria surfaces and the electronic and geometric character of the relevant interfaces. Nanostructured ceria, including particles(polyhedra), rods, and cubes, provides anchoring sites for the copper species. The atomic arrangements and chemical properties of the(111),(110) and(100) facets, preferentially exposed depending on the shape of ceria, govern the copper-ceria interactions and in turn determine their catalytic properties. Also, the metal loading significantly influences the dispersion of copper species on ceria with a specific shape, forming copper layers, clusters, and nanoparticles. Lower copper contents result in copper monolayers and/or bilayers while higher copper loadings lead to multi-layered clusters and faceted particles. The active sites are usually generated via interactions between the copper atoms in the metal species and the oxygen vacancies on ceria, which is closely linked to the number and density of surface oxygen vacancies dominated by the shape of ceria.展开更多
Composite supports CeO2-ZrO2-Al2O3(CZA) and CeO2-ZrO2-Al2O3-La2O3(CZALa) were prepared by co-precipitation method. Palladium catalysts were prepared by impregnation and their purification ability for CH4, CO and N...Composite supports CeO2-ZrO2-Al2O3(CZA) and CeO2-ZrO2-Al2O3-La2O3(CZALa) were prepared by co-precipitation method. Palladium catalysts were prepared by impregnation and their purification ability for CH4, CO and NOx in the mixture gas simulated the exhaust from natural gas vehicles (NGVs) operated under stoichiometric condition was investigated. The effect of La2O3 on the physicochemical properties of supports and catalysts was characterized by various techniques. The characterizations with X-ray diffraction (XRD) and Raman spectroscopy revealed that the doping of La2O3 restrained effectively the sintering of crystallite particles, maintained the crystallite particles in nanoscale and stabilized the crystal phase after calcination at 1000 ℃. The results of N2-adsorption, H2-temperatnre-programmed reduction (H2-TPR) and oxygen storage capacity (OSC) measurements indicated that La2O3 improved the textural properties, reducibility and OSC of composite supports. Activity testing results showed that the catalysts exhibit excellent activities for the simultaneous removal of methane, CO and NOx in the simulated exhaust gas. The catalysts supported on CZALa showed remarkable thermal stability and catalytic activity for the three pollutants, especially for NOx. The prepared palladium catalysts have high ability to remove NOx, CH4 and CO, and they can be used as excellent catalysts for the purification of exhaust from NGVs operated under stoichiometric condition. The catalysts reported in this work also have significant potential in industrial application because of their high performance and low cost.展开更多
CeO2-promoted Ni/Al2O3-ZrO2 (Ni/Al2O3-ZrO2-CeO2) catalysts were prepared by a direct sol-gel process with citric acid as gelling agent. The catalysts used for the methane reforming with CO2 was studied by infrared s...CeO2-promoted Ni/Al2O3-ZrO2 (Ni/Al2O3-ZrO2-CeO2) catalysts were prepared by a direct sol-gel process with citric acid as gelling agent. The catalysts used for the methane reforming with CO2 was studied by infrared spectroscopy (IR), thermal gravimetric analysis (TGA), microscopic analysis, X-ray diffraction (XRD) and temperature-programmed reduction (TPR). The catalytic performance for CO2 reforming of methane to synthesis gas was investigated in a continuous-flow micro-reactor under atmospheric pressure. TGA, IR, XRD and microscopic analysis show that the catalysts prepared by the direct sol-gel process consist of Ni particles with a nanostructure of around 5 nm and an amorphous-phase composite oxide support. There exists a chemical interaction between metallic Ni particles and supports, which makes metallic Ni well dispersed, highly active and stable. The addition of CeO2 effectively improves the dispersion and the stability of Ni particles of the prepared catalysts, and enhances the adsorption of CO2 on the surface of catalysts. The catalytic tests for methane reforming with CO2 to synthesis gas show that the Ni/Al2O3-ZrO2-CeO2 catalysts show excellent activity and stability compared with the Ni/Al2O3 catalyst. The excellent catalytic activity and stability of the Ni/Al2O3-ZrO2-CeO2 are attributed to the highly, uniformly and stably dispersed small metallic Ni particles, the high reducibility of the Ni oxides and the interaction between metallic Ni particles and the composite oxide supports.展开更多
The oxidative properties and characterization of CuO, CeO 2 and CuO/CeO 2 cata lysts were examined by means of a CO micro-reactor GC system, TPR, XPS and X-r ay diffraction Rietveld methods. The results show that ei...The oxidative properties and characterization of CuO, CeO 2 and CuO/CeO 2 cata lysts were examined by means of a CO micro-reactor GC system, TPR, XPS and X-r ay diffraction Rietveld methods. The results show that either CuO or CeO 2 ac tivity is quite low for CO oxidation. However, when CuO and CeO 2 are mixed, the oxidative activity of the catalyst increases significantly, probably owing to the valency status of copper species (Cu 2+ and Cu+) on the CeO 2 surfa ce, the dispersion and reducibility. XPS surface analysis shows that CuO loading is very important in forming of either Cu 2+ or Cu+. Rietveld analysis s hows that some CuO, which has smaller ion radius than Ce 4+, enters the Ce O 2 lattice after CuO and CeO 2 are mixed. When the CuO loading reaches 5.0%, the size of CuO crystals is a minimum (6.1 nm) and the micro-strain value i s a maximum (2.86×10 -3), resulting in high surface energy and the best ac tivity for CO oxidation.展开更多
In this work, we have reported the influence of the addition of base (KOH) on the physicochemical property of ceria synthesized by alcohothermal process, and the alcohothermal mechanism was also put forward. Further...In this work, we have reported the influence of the addition of base (KOH) on the physicochemical property of ceria synthesized by alcohothermal process, and the alcohothermal mechanism was also put forward. Furthermore, the prepared CeO2 was used as the support to prepare CuO/CeO2 catalysts via the wet impregnation method. The samples were characterized by N2 adsorption-desorption, X-ray powder diffraction (XRD), high resolution transmission electron microscopy (HRTEM), and temperatureprogrammed reduction by H2 (H2-TPR). The catalytic properties of the CuO/CeO2 catalysts for lowtemperature CO oxidation were studied using a microreactor-GC system. The crystal size of CeO2-A was much smaller than that of CeO2-B, and the corresponding copper oxide catalysts exhibited higher catalytic activity than that of the CeO2-B-supported catalysts under the same reaction conditions. The alcohothermal mechanism indicated that KOH plays a key role in determining the physicochemical and catalytic properties of ceria-based materials.展开更多
Cu/CeO2-ZrO2 catalysts for water-gas shift (WGS) reaction were prepared with co-precipitation method, and the influence of ZrO2 content on the catalytic structure and properties was investigated by the techniques of...Cu/CeO2-ZrO2 catalysts for water-gas shift (WGS) reaction were prepared with co-precipitation method, and the influence of ZrO2 content on the catalytic structure and properties was investigated by the techniques of N2 physical adsorption analysis, XRD and H2-TPR. The results indicate that the BET surface areas of the catalysts are increased in varying degrees due to the presence of ZrO2. With increasing ZrO2 content, the pore size distribution is centered on 1.9 nm. ZrO2 can efficiently restrain the growth of Cu crystal particles. The appropriate amount of ZrO2 in the Cu/CeO2 catalysts can help the catalyst keep better copper dispersion in the WGS reaction, which can lead to both higher catalytic activity and better thermal stability. When ZrO2 content is 10% (atom fraction), Cu/CeO2-Zr02 catalyst reaches a CO conversion rate of 73.7% at the reaction temperature of 200℃.展开更多
This paper presented a study on the role of yttrium addition to CuO/CeO2 catalyst for water-gas shift reaction. A single-step co-precipitation method was used for preparation of a series of yttrium doped CuO/CeO2 cata...This paper presented a study on the role of yttrium addition to CuO/CeO2 catalyst for water-gas shift reaction. A single-step co-precipitation method was used for preparation of a series of yttrium doped CuO/CeO2 catalysts with yttrium content in the range of 0-5wt.%. Properties of the obtained samples were characterized and analyzed by X-ray diffraction (XRD), Raman spectroscopy, H2-TPR, cyclic voltammetry (CV) and the BET method. The results revealed that catalytic activity was increased with the yttrium content at first, but then decreased with the further increase of yttrium content. Herein, CuO/CeO2 catalyst doped with 2wt.% of yttrium showed the highest catalytic activity (CO conversion reaches 93.4% at 250 ℃) and thermal stability for WGS reaction. The catalytic activity was correlated with the surface area, the area of peak γ of H2-TPR profile (i.e., the reduction of surface copper oxide (crystalline forms) interacted with surface oxygen vacancies on ceria), and the area of peak C2 and A1 (Cu^0→←Cu^2+ in cyclic voltammetry process), respectively. Besides, Raman spectra provided evidences for a synergistic Cu-Ovacancy interaction, and it was indicated that doping yttrium may facilitate the formation of oxygen vacancies on ceria.展开更多
Au/Al2O3 catalyst was prepared by a modified anion impregnation method and investigated with respect to its initial activity and stability for low-temperature CO oxidation.The activity changes of the catalyst were exa...Au/Al2O3 catalyst was prepared by a modified anion impregnation method and investigated with respect to its initial activity and stability for low-temperature CO oxidation.The activity changes of the catalyst were examined after separate treatment in CO+O2 or CO2 +O2 .Furthermore,in situ FT-IR studies were performed to investigate the species on the surface when CO or CO+O2 or CO2 +O2 was selected separately as adsorption gas.The results showed that Au/Al2O3 catalyst exhibited very high initial activity,but the catalytic activity was found to decrease gradually during CO oxidation with time on stream.And also,the activity of the catalyst declined after treatment in CO+O2 or CO2 +O2 .The formation and accumulation of carbonate-like species during CO oxidation or treatment in CO+O2 or CO2 +O2 might be mainly responsible for the activity decrease,which was reversible.展开更多
A series of catalysts on the basis of 10 wt.% CuO/y-AI203, 10 wt.% CuO + 10 wt.% Cr2O3/y-AI203 and 15 wt.% MnO2/y -A1203 have been prepared and modified by CeO2 with contents up to 20 wt.%. Physico-chemical propertie...A series of catalysts on the basis of 10 wt.% CuO/y-AI203, 10 wt.% CuO + 10 wt.% Cr2O3/y-AI203 and 15 wt.% MnO2/y -A1203 have been prepared and modified by CeO2 with contents up to 20 wt.%. Physico-chemical properties of the catalysts were determined by the methods of BET Adsorption, XRD, and TPR. Oxidative activity of the catalysts was studied at the temperature range 90-220 ℃and CO concentration of 3 mol.%. Addition of CeO2 led to changes in physico-chemical properties of the catalysts and formation of novel active centres that increased the activity of CuO and Cr203 containing catalysts, but decreased the activity of those, containing MnO2. The catalyst sample containing 10 wt.% CuO and 15 wt.% CeO2 has been shown to be the best one for complete conversion of CO. At the given conditions on this catalyst the complete oxidation of CO to CO2 occurred at 130 ~C during more than 500 h.展开更多
The noble metals (Pt, Pd, Rh) supported on Cu-Ce mixed oxides with γ-Al2O3 washcoat/FeCrAl substrate were investigated as catalytic performance of Three Way Catalysts (TWC) under simulated automotive exhaust feed gas...The noble metals (Pt, Pd, Rh) supported on Cu-Ce mixed oxides with γ-Al2O3 washcoat/FeCrAl substrate were investigated as catalytic performance of Three Way Catalysts (TWC) under simulated automotive exhaust feed gas. The structural, morphological features and catalytic activity were observed by X-ray diffractometry (XRD), scanning electron microscopy (SEM), Brunauer-Emmett-Teller (BET), X-ray photoelectron spectroscopy (XPS) and GC-TCD (Varian CP-4900). The catalytic performance of noble metals (Pt, Rh, Pd) supported on Cu-Ce mixed oxides with γ-Al2O3 washcoat/FeCrAl substrate was be compared with noble metals (Pt, Rh, Pd) supported on Ce-Zr mixed oxides with γ-Al2O3 washcoat/FeCrAl substrate and only γ-Al2O3 washcoat/FeCrAl substrate at various stoichiometric ratio of oxygen. The results showed that the addition of Cu-Ce mixed oxides improved CO oxidation reaction at lower temperature during stable lambda of 1, the highest CO conversion of 99% is observed for the noble metals (Pt, Pd, Rh) support on Cu-Ce with γ-Al2O3 washcoat/FeCrAl substrate. The results also showed that, the addition of Cu-Ce mixed oxides promoted released oxygen, thus it improved strongly CO and C3H8 conversion at lean oxygen stoichiometric operation.展开更多
基金supported by the National Natural Science Foundation of China(21590792,91645203 and 21521091)~~
文摘We examined the water adsorption and dissociation on ceria surfaces as well as ceria‐supported Au single‐atom catalysts using density functional theory calculations.Molecular and dissociative water were observed to coexist on clean CeO2and reduced Au1/CeO2?x surfaces because of the small difference in adsorption energies,whereas the presence of dissociative water was highly favorable on reduced CeO2?x and clean Au1/CeO2surfaces.Positively charged Au single atoms on the ceria surface not only provided activation sites for water adsorption but also facilitated water dissociation by weakening the intramolecular O-H bonds.In contrast,negatively charged Au single atoms were not reactive for water adsorption because of the saturation of Au5d and6s electron shells.This work provides a fundamental understanding of the interaction between water and single‐atom Au catalysts.
文摘气氛环境下原位研究催化剂的烧结行为,能够为理解催化剂在预处理以及反应条件下的烧结机理和高稳定催化剂的设计提供重要的实验依据。本文以Au/CeO_(2)模型纳米催化剂为研究对象,利用环境透射电子显微镜原位观察其在O_(2)与CO气氛下的高温动态烧结过程。实验发现,负载在CeO_(2)上的Au纳米颗粒在O_(2)与CO气氛环境中表现出不同的烧结行为,其在O_(2)气氛下具有较高的烧结速度,同时存在颗粒迁移与聚集长大(particle migration and coalescence,PMC)和奥斯特瓦尔德熟化(Ostwald ripening,OR)两种烧结过程;在CO气氛下烧结速度较慢,烧结过程以OR为主。对比不同气氛环境下烧结后催化剂的表面结构可知,CO增加了CeO_(2)表面台阶的数量以及表面氧空位浓度,增强了载体对Au颗粒的锚定作用,从而提升Au/CeO_(2)催化剂的稳定性。
基金supported by the National Natural Science Foundation of China (No. 21507130)the Open Project Program of Beijing National Laboratory for Molecular Sciences (No. 20140142)+3 种基金the Open Project Program of Chongqing Key Laboratory of Environmental Materials and Remediation Technology from Chongqing University of Arts and Sciences (No. CEK1405)the Open Project Program of Jiangsu Key Laboratory of Vehicle Emissions Control (No. OVEC001)the Open Project Program of Chongqing Key Laboratory of Catalysis and Functional Organic Molecules from Chongqing Technology and Business University (1456029)the Chongqing Science & Technology Commission (Nos. cstc2016jcyj A0070, cstc2014pt-gc20002, cstckjcxljrc13)~~
文摘This work examines the influence of preparation methods on the physicochemical properties and catalytic performance of MnOx‐CeO2 catalysts for selective catalytic reduction of NO by NH3 (NH3‐SCR) at low temperature. Five different methods, namely, mechanical mixing, impregnation,hydrothermal treatment, co‐precipitation, and a sol‐gel technique, were used to synthesizeMnOx‐CeO2 catalysts. The catalysts were characterized in detail, and an NH3‐SCR model reaction waschosen to evaluate the catalytic performance. The results showed that the preparation methodsaffected the catalytic performance in the order: hydrothermal treatment > sol‐gel > co‐precipitation> impregnation > mechanical mixing. This order correlated with the surface Ce3+ and Mn4+ content,oxygen vacancies and surface adsorbed oxygen species concentration, and the amount of acidic sitesand acidic strength. This trend is related to redox interactions between MnOx and CeO2. The catalystformed by a hydrothermal treatment exhibited excellent physicochemical properties, optimal catalyticperformance, and good H2O resistance in NH3‐SCR reaction. This was attributed to incorporationof Mnn+ into the CeO2 lattice to form a uniform ceria‐based solid solution (containing Mn‐O‐Cestructures). Strengthening of the electronic interactions between MnOx and CeO2, driven by thehigh‐temperature and high‐pressure conditions during the hydrothermal treatment also improved the catalyst characteristics. Thus, the hydrothermal treatment method is an efficient and environment‐friendly route to synthesizing low‐temperature denitrification (deNOx) catalysts.
基金Projected supported by the National Natural Science Foundation of China (20271028) and Tianjin Natural Science Foundation(033602511)
文摘CeO2 was synthesized via sol-gel process and used as supporter to prepare CuO/CeO2, Cu/CeO2 catalysts by impregnation method. The catalytic properties and characterization of CeO2, CuO/CeO2 and Cu/CeO2 catalysts were examined by means of a microreactor-GC system, HRTEM, XRD, TPR and XPS techniques. The results show that CuO has not catalytic activity and the activity of CeO2 is quite low for CO oxidation. However, the catalytic activity of CuO/CeO2 and Cu/ CeO2 catalysts increases significantly. Furthermore, the activity of CuO/CeO2 is higher than that of Cu/CeO2 catalysts.
基金National Natural Science Foundation of China (nos.21476226 and 21506204)National Key Projects for Fundamental Research and Development of China (2016YFB0600902)+1 种基金the Strategic Priority Research Program of the Chinese Academy of Sciences (XDB17020400)the Youth Innovation Promotion Association CAS for financial support
文摘Reverse water gas shift (RWGS) reaction can serve as a pivotal stage in the CO2 conversion processes, which is vital for the utilization of CO2. In this study, RWGS reaction was performed over Pt/CeO2 catalysts at the temperature range of 200-500 degrees C under ambient pressure. Compared with pure CeO2, Pt/CeO2 catalysts exhibited superior RWGS activity at lower reaction temperature. Meanwhile, the calculated TOF and E-a values are approximately the same over these Pt/CeO2 catalysts pretreated under various calcination conditions, indicating that the RWGS reaction is not affected by the morphologies of anchored Pt nanoparticles or the primary crystallinity of CeO2. TPR and XPS results indicated that the incorporation of Pt promoted the reducibility of CeO2 support and remarkably increased the content of Ce 3 + sites on the catalyst surface. Furthermore, the CO TPSR-MS signal under the condition of pure CO2 flow over Pt/CeO 2 catalyst is far lower than that under the condition of adsorbed CO2 with H-2 -assisted flow, revealing that CO2 molecules adsorbed on Ce3+ active sites have difficult in generating CO directly. Meanwhile, the adsorbed CO2 with the assistance of H-2 can form formate species easily over Ce3+ active sites and then decompose into Ce3+-CO species for CO production, which was identified by in-situ FTIR. (C) 2016 Science Press and Dalian Institute of Chemical Physics, Chinese Academy of Sciences. Published by Elsevier B. V. and Science Press. All rights reserved.
基金the National Natural Science Foundation of China (20563003)Natural Science Foundation of Inner Mongolia (200508010203)
文摘Aqueous precipitation and deposition-precipitation method were used to prepare CeO2 supports and Au/CeO2 catalysts, respectively. The effect of preparation condition of support on the catalyst activity was investigated. The catalytic combustion of HCHO was considered as the probe reaction for comparing the catalyst activity. The BET, X-ray diffraction, X-ray photoelectron spectroscopy (XPS), and reduction (TPR) were carried out to analyze the influence factor on the catalysts activity. The results showed that the addition of dispersant and use of microwave in the support preparation procedure could be beneficial for enhancing the interaction of supports and gold species and thus improved the catalytic activity. The total conversion temperature for HCHO was 146 ℃ over AC400. With the modification during supports preparation process, the catalytic activity increased with total conversion temperature decreasing to 98 ℃. The results of XPS indicated that Au^0 and Au^+1 species coexisted in these catalysts and the activity of catalyst correlated with Au^+1/Au^0 ratio. Temperature-programmed reduction results demonstrated that the reduction peak appeared between 100-170 ℃ with the inducing of gold. The dependence of activity on the reduction peak temperature implied that ionic gold was catalytic activity component for HCHO oxidation.
文摘The catalyst screening tests for carbon dioxide oxidative coupling of methane (CO2-OCM) have been investigated over ternary and binary metal oxide catalysts. The catalysts are prepared by doping MgO- and CeO2-based solids with oxides from alkali (Li2O), alkaline earth (CaO), and transition metal groups (WO3 or MnO). The presence of the peroxide (O2-2) active sites on the Li2O2, revealed by Raman spectroscopy, may be the key factor in the enhanced performance of some of the Li2O/MgO catalysts. The high reducibility of the CeO2 catalyst, an important factor in the CO2-OCM catalyst activity, may be enhanced by the presence of manganese oxide species. The manganese oxide species increases oxygen mobility and oxygen vacancies in the CeO2 catalyst. Raman and Fourier Transform Infra Red (FT-IR) spectroscopies revealed the presence of lattice vibrations of metal-oxygen bondings and active sites in which the peaks corresponding to the bulk crystalline structures of Li2O, CaO, WO3 and MnO are detected. The performance of 5%MnO/15%CaO/CeO2 catalyst is the most potential among the CeO2-based catalysts, although lower than the 2%Li2O/MgO catalyst. The 2%Li2O/MgO catalyst showed the most promising C2+ hydrocarbons selectivity and yield at 98.0% and 5.7%, respectively.
文摘CeO2-Co3O4 catalysts for low-temperature CO oxidation were prepared by a co-precipitation method. In combination with the characterization methods of N2 adsorption/desorption, XRD, temperature-programmed reduction (TPR), and FT-IR, the influence of the cerium content on the catalytic performance of CeO2-Co3O4 was investigated. The results indicate that the prepared CeO2-Co3O4 catalysts exhibit a better activity than that of pure CeO2 or pure Co3O4. The catalyst with the Ce/Co atomic ratio 1 : 16 exhibits the best activity, which converts 77% of CO at room temperature and completely oxidizes CO at 45 ℃.
文摘The atomic structure of the active sites in Cu/CeO2 catalysts is intimately associated with the copper-ceria interaction. Both the shape of ceria and the loading of copper affect the chemical bonding of copper species on ceria surfaces and the electronic and geometric character of the relevant interfaces. Nanostructured ceria, including particles(polyhedra), rods, and cubes, provides anchoring sites for the copper species. The atomic arrangements and chemical properties of the(111),(110) and(100) facets, preferentially exposed depending on the shape of ceria, govern the copper-ceria interactions and in turn determine their catalytic properties. Also, the metal loading significantly influences the dispersion of copper species on ceria with a specific shape, forming copper layers, clusters, and nanoparticles. Lower copper contents result in copper monolayers and/or bilayers while higher copper loadings lead to multi-layered clusters and faceted particles. The active sites are usually generated via interactions between the copper atoms in the metal species and the oxygen vacancies on ceria, which is closely linked to the number and density of surface oxygen vacancies dominated by the shape of ceria.
基金supported by the National Natural Science Foundation of China (No. 20773090, 20803049)the National High Technology Researchand Development Program of China (863 Program, No. 2006AA06Z347)the Specialized Research Fund for the Doctoral Program of Higher Education(20070610026)
文摘Composite supports CeO2-ZrO2-Al2O3(CZA) and CeO2-ZrO2-Al2O3-La2O3(CZALa) were prepared by co-precipitation method. Palladium catalysts were prepared by impregnation and their purification ability for CH4, CO and NOx in the mixture gas simulated the exhaust from natural gas vehicles (NGVs) operated under stoichiometric condition was investigated. The effect of La2O3 on the physicochemical properties of supports and catalysts was characterized by various techniques. The characterizations with X-ray diffraction (XRD) and Raman spectroscopy revealed that the doping of La2O3 restrained effectively the sintering of crystallite particles, maintained the crystallite particles in nanoscale and stabilized the crystal phase after calcination at 1000 ℃. The results of N2-adsorption, H2-temperatnre-programmed reduction (H2-TPR) and oxygen storage capacity (OSC) measurements indicated that La2O3 improved the textural properties, reducibility and OSC of composite supports. Activity testing results showed that the catalysts exhibit excellent activities for the simultaneous removal of methane, CO and NOx in the simulated exhaust gas. The catalysts supported on CZALa showed remarkable thermal stability and catalytic activity for the three pollutants, especially for NOx. The prepared palladium catalysts have high ability to remove NOx, CH4 and CO, and they can be used as excellent catalysts for the purification of exhaust from NGVs operated under stoichiometric condition. The catalysts reported in this work also have significant potential in industrial application because of their high performance and low cost.
基金supported by the National Natural Science Foundation of China (NO. 20976013, 21006057)
文摘CeO2-promoted Ni/Al2O3-ZrO2 (Ni/Al2O3-ZrO2-CeO2) catalysts were prepared by a direct sol-gel process with citric acid as gelling agent. The catalysts used for the methane reforming with CO2 was studied by infrared spectroscopy (IR), thermal gravimetric analysis (TGA), microscopic analysis, X-ray diffraction (XRD) and temperature-programmed reduction (TPR). The catalytic performance for CO2 reforming of methane to synthesis gas was investigated in a continuous-flow micro-reactor under atmospheric pressure. TGA, IR, XRD and microscopic analysis show that the catalysts prepared by the direct sol-gel process consist of Ni particles with a nanostructure of around 5 nm and an amorphous-phase composite oxide support. There exists a chemical interaction between metallic Ni particles and supports, which makes metallic Ni well dispersed, highly active and stable. The addition of CeO2 effectively improves the dispersion and the stability of Ni particles of the prepared catalysts, and enhances the adsorption of CO2 on the surface of catalysts. The catalytic tests for methane reforming with CO2 to synthesis gas show that the Ni/Al2O3-ZrO2-CeO2 catalysts show excellent activity and stability compared with the Ni/Al2O3 catalyst. The excellent catalytic activity and stability of the Ni/Al2O3-ZrO2-CeO2 are attributed to the highly, uniformly and stably dispersed small metallic Ni particles, the high reducibility of the Ni oxides and the interaction between metallic Ni particles and the composite oxide supports.
文摘The oxidative properties and characterization of CuO, CeO 2 and CuO/CeO 2 cata lysts were examined by means of a CO micro-reactor GC system, TPR, XPS and X-r ay diffraction Rietveld methods. The results show that either CuO or CeO 2 ac tivity is quite low for CO oxidation. However, when CuO and CeO 2 are mixed, the oxidative activity of the catalyst increases significantly, probably owing to the valency status of copper species (Cu 2+ and Cu+) on the CeO 2 surfa ce, the dispersion and reducibility. XPS surface analysis shows that CuO loading is very important in forming of either Cu 2+ or Cu+. Rietveld analysis s hows that some CuO, which has smaller ion radius than Ce 4+, enters the Ce O 2 lattice after CuO and CeO 2 are mixed. When the CuO loading reaches 5.0%, the size of CuO crystals is a minimum (6.1 nm) and the micro-strain value i s a maximum (2.86×10 -3), resulting in high surface energy and the best ac tivity for CO oxidation.
文摘In this work, we have reported the influence of the addition of base (KOH) on the physicochemical property of ceria synthesized by alcohothermal process, and the alcohothermal mechanism was also put forward. Furthermore, the prepared CeO2 was used as the support to prepare CuO/CeO2 catalysts via the wet impregnation method. The samples were characterized by N2 adsorption-desorption, X-ray powder diffraction (XRD), high resolution transmission electron microscopy (HRTEM), and temperatureprogrammed reduction by H2 (H2-TPR). The catalytic properties of the CuO/CeO2 catalysts for lowtemperature CO oxidation were studied using a microreactor-GC system. The crystal size of CeO2-A was much smaller than that of CeO2-B, and the corresponding copper oxide catalysts exhibited higher catalytic activity than that of the CeO2-B-supported catalysts under the same reaction conditions. The alcohothermal mechanism indicated that KOH plays a key role in determining the physicochemical and catalytic properties of ceria-based materials.
文摘Cu/CeO2-ZrO2 catalysts for water-gas shift (WGS) reaction were prepared with co-precipitation method, and the influence of ZrO2 content on the catalytic structure and properties was investigated by the techniques of N2 physical adsorption analysis, XRD and H2-TPR. The results indicate that the BET surface areas of the catalysts are increased in varying degrees due to the presence of ZrO2. With increasing ZrO2 content, the pore size distribution is centered on 1.9 nm. ZrO2 can efficiently restrain the growth of Cu crystal particles. The appropriate amount of ZrO2 in the Cu/CeO2 catalysts can help the catalyst keep better copper dispersion in the WGS reaction, which can lead to both higher catalytic activity and better thermal stability. When ZrO2 content is 10% (atom fraction), Cu/CeO2-Zr02 catalyst reaches a CO conversion rate of 73.7% at the reaction temperature of 200℃.
基金supported by the National Natural Science Foundation of China (20771025)A-type Science and Technology Projects of Fujian Provincial Department of Education (JA08021)
文摘This paper presented a study on the role of yttrium addition to CuO/CeO2 catalyst for water-gas shift reaction. A single-step co-precipitation method was used for preparation of a series of yttrium doped CuO/CeO2 catalysts with yttrium content in the range of 0-5wt.%. Properties of the obtained samples were characterized and analyzed by X-ray diffraction (XRD), Raman spectroscopy, H2-TPR, cyclic voltammetry (CV) and the BET method. The results revealed that catalytic activity was increased with the yttrium content at first, but then decreased with the further increase of yttrium content. Herein, CuO/CeO2 catalyst doped with 2wt.% of yttrium showed the highest catalytic activity (CO conversion reaches 93.4% at 250 ℃) and thermal stability for WGS reaction. The catalytic activity was correlated with the surface area, the area of peak γ of H2-TPR profile (i.e., the reduction of surface copper oxide (crystalline forms) interacted with surface oxygen vacancies on ceria), and the area of peak C2 and A1 (Cu^0→←Cu^2+ in cyclic voltammetry process), respectively. Besides, Raman spectra provided evidences for a synergistic Cu-Ovacancy interaction, and it was indicated that doping yttrium may facilitate the formation of oxygen vacancies on ceria.
基金supported by the Science and Research Reward Fund Program of Shandong Excellent Young Scientist of China (2007BS04033)
文摘Au/Al2O3 catalyst was prepared by a modified anion impregnation method and investigated with respect to its initial activity and stability for low-temperature CO oxidation.The activity changes of the catalyst were examined after separate treatment in CO+O2 or CO2 +O2 .Furthermore,in situ FT-IR studies were performed to investigate the species on the surface when CO or CO+O2 or CO2 +O2 was selected separately as adsorption gas.The results showed that Au/Al2O3 catalyst exhibited very high initial activity,but the catalytic activity was found to decrease gradually during CO oxidation with time on stream.And also,the activity of the catalyst declined after treatment in CO+O2 or CO2 +O2 .The formation and accumulation of carbonate-like species during CO oxidation or treatment in CO+O2 or CO2 +O2 might be mainly responsible for the activity decrease,which was reversible.
文摘A series of catalysts on the basis of 10 wt.% CuO/y-AI203, 10 wt.% CuO + 10 wt.% Cr2O3/y-AI203 and 15 wt.% MnO2/y -A1203 have been prepared and modified by CeO2 with contents up to 20 wt.%. Physico-chemical properties of the catalysts were determined by the methods of BET Adsorption, XRD, and TPR. Oxidative activity of the catalysts was studied at the temperature range 90-220 ℃and CO concentration of 3 mol.%. Addition of CeO2 led to changes in physico-chemical properties of the catalysts and formation of novel active centres that increased the activity of CuO and Cr203 containing catalysts, but decreased the activity of those, containing MnO2. The catalyst sample containing 10 wt.% CuO and 15 wt.% CeO2 has been shown to be the best one for complete conversion of CO. At the given conditions on this catalyst the complete oxidation of CO to CO2 occurred at 130 ~C during more than 500 h.
文摘The noble metals (Pt, Pd, Rh) supported on Cu-Ce mixed oxides with γ-Al2O3 washcoat/FeCrAl substrate were investigated as catalytic performance of Three Way Catalysts (TWC) under simulated automotive exhaust feed gas. The structural, morphological features and catalytic activity were observed by X-ray diffractometry (XRD), scanning electron microscopy (SEM), Brunauer-Emmett-Teller (BET), X-ray photoelectron spectroscopy (XPS) and GC-TCD (Varian CP-4900). The catalytic performance of noble metals (Pt, Rh, Pd) supported on Cu-Ce mixed oxides with γ-Al2O3 washcoat/FeCrAl substrate was be compared with noble metals (Pt, Rh, Pd) supported on Ce-Zr mixed oxides with γ-Al2O3 washcoat/FeCrAl substrate and only γ-Al2O3 washcoat/FeCrAl substrate at various stoichiometric ratio of oxygen. The results showed that the addition of Cu-Ce mixed oxides improved CO oxidation reaction at lower temperature during stable lambda of 1, the highest CO conversion of 99% is observed for the noble metals (Pt, Pd, Rh) support on Cu-Ce with γ-Al2O3 washcoat/FeCrAl substrate. The results also showed that, the addition of Cu-Ce mixed oxides promoted released oxygen, thus it improved strongly CO and C3H8 conversion at lean oxygen stoichiometric operation.