B2-CuZr reinforced amorphous alloy matrix composites:A review

B2-CuZr phase reinforced amorphous alloy matrix composites has become one of the research hotspots in the field of materials science due to the“transformation-induced plasticity”phenomenon,which makes the composites show better macroscopic plastic deformability and obvious work-hardening behavior compared to the conventional amorphous alloy matrix composites reinforced with ductile phases.However,the in-situ metastable B2-CuZr phase tends to undergo eutectoid decomposition during solidification,and the volume fraction,size,and distribution of B2-CuZr phase are difficult to control,which limits the development and application of these materials.To date,much efforts have been made to solve the above problems through composition optimization,casting parameter tailoring,and post-processing technique.In this study,a review was given based on relevant studies,focusing on the predictive approach,reinforcing mechanism,and microstructure tailoring methods of B2-CuZr phase reinforced amorphous alloy matrix composites.The research focus and future prospects were also given for the future development of the present composite system.

Structures and electrochemical hydrogen storage performance of Si added A_2B_7-type alloy electrodes

In order to ameliorate the electrochemical hydrogen storage performance of La-Mg-Ni system A2B7-type electrode alloys, a small amount of Si was added. The La0.8Mg0.2Ni3.3Co0.2Six （x=0-0.2） electrode alloys were prepared by casting and annealing. The effects of adding Si on the structure and electrochemical hydrogen storage characteristics of the alloys were investigated systematically. The results indicate that the as-cast and annealed alloys hold multiple structures, involving two major phases of （La, Mg）2Ni7 with a Ce2Ni7-type hexagonal structure and LaNi5 with a CaCu5-type hexagonal structure as well as one residual phase LaNi3. The addition of Si results in a decrease in （La, Mg）2Ni7 phase and an increase in LaNi5 phase without changing the phase structure of the alloys. What is more, it brings on an obvious effect on electrochemical hydrogen storage characteristics of the alloys. The discharge capacities of the as-cast and annealed alloys decline with the increase of Si content, but their cycle stabilities clearly grow under the same condition. Furthermore, the measurements of the high rate discharge ability, the limiting current density, hydrogen diffusion coefficient as well as electrochemical impedance spectra all indicate that the electrochemical kinetic properties of the electrode alloys first increase and then decrease with the rising of Si content.

Electrochemical performances of as-cast and annealed La_(0.8-x)Nd_xMg_(0.2)Ni_(3.35)Al_(0.1)Si_0.05(x=0-0.4) alloys applied to Ni/metal hydride (MH) battery

The La-Mg-Ni-based A2B7-type Lao.8_xNdx Mgo.2Ni3.35Alo.lSio.o5 （x = 0, 0.1, 0.2, 0.3, and 0.4） electrode alloys were prepared by casting and annealing. The influence of the partial substitution of Nd for La on the structure and electrochemical performances of the alloys was investigated. The structural analysis of X-ray diffraction and scanning electron microscopy reveals that the experimental alloys consist of two major phases： （La,Mg）2Ni7 with the hexagonal Ce2Ni7-type structure and LaNi5 with the hexagonal CaCus-type structure as well as some residual phases of LaNi3 and NdNis. The electrochemical measurements indicate that an evident change of the electrochemical performance of the alloys is associated with the substitution of Nd for La. The discharge capacity of the alloy first increases then decreases with the growing Nd content, whereas their cycle stability clearly grows all the time. Furthermore, the measurements of the high rate discharge ability, the limiting current density, and hydrogen diffusion coefficient all demonstrate that the electrochemical kinetic properties of the alloy electrodes first augment then decline with the rising amount of Nd substitution.

Precipitation behavior of B2-like particles in Fe-Cu binary alloy

The precipitation behavior in Fe-Cu binary allow was investigated undertransmission electron microscope (TEM) during aging at 650 deg C for the time range of 100 s to 300h. In addition to the zones with higher copper content and epsilon-Cu were observed, a metastablephase with B2-like structure was found in the early stage of the precipitation process, which isquite different from the equilibrium copper phase shown in the Fe-Cu binary phase diagram and hasperfect coherent relationship to the alpha-Fe matrix. The appearance of B2-like structure is veryimportant concerning the mechanism of aging strengthening effect and mechanical properties ofcorresponding engineering steels and alloys containing copper.

An investigation on electrochemical performances of as-cast and annealed La_(0.8)Mg_(0.2)Ni_(3.3)Co_(0.2)Si_x(x=0-0.2)alloy electrodes for Ni/MH battery application

The La-Mg-Ni-based A2B7-type La0.5Mg0.2Ni3.3Co0.2Six （x=0-0.2） electrode alloys were prepared by casting and annealing. The influences of the additional silicon and the annealing treatment on the structure and electrochemical performances of the alloys were investigated systemically. Both of the analyses of XRD and SEM reveal that the as-cast and annealed alloys are of a multiphase structure, involving two main phases （La, Mg）2Ni7 and LaNi5 as well as one minor phase LaNi3. The addition of Si and annealing treatment bring on an evident change in the phase abundances and cell parameters of （La, Mg）2Ni7 and LaNi5 phase for the alloy without altering its phase structure. The phase abundances decrease from 74.3% （x=0） to 57.8% （x=0.2） for the （La, Mg）2Ni7 phase, and those of LaNi5 phase increase from 20.2% （x^0） to 37.3% （x=0.2）. As for the electrochemical measurements, adding Si and performing annealing treatment have engendered obvious impacts. The cycle stability of the alloys is improved dramatically, being enhanced from 80.3% to 93.7% for the as-annealed （950 ℃） alloys with Si content increasing from 0 to 0.2. However, the discharge capacity is reduced by adding Si, from 399.4 to 345.3 mA.h/g as the Si content increases from 0 to 0.2. Furthermore, such addition makes the electrochemical kinetic properties of the alloy electrodes first increase and then decrease. Also, it is found that the overall electrochemical properties of the alloys first augment and then fall with the annealing temperature rising.

Effect of nano-sized Al2O3 reinforcing particles on uniaxial and high cycle fatigue behaviors of hot-forged AZ31B magnesium alloy

The effect of hot-forging process was investigated on microstructural and mechanical properties of AZ31 B alloy and AZ31 B/1.5 vol.%Al2 O3 nanocomposite under static and cycling loading. The as-cast alloy and composite were firstly subjected to a homogenization heat treatment at 450 ℃ and then an open-die forging at 450 ℃. The results indicated that the presence of reinforcing particles led to grain refinement and improvement of dynamic recrystallization. The forging process was more effective to eliminate the porosity in the cast alloy workpiece. Microhardness of the forged composite was increased by up to 80% and 16%, in comparison with those of the cast and forged alloy samples, respectively. Ultimate tensile strength and maximum tensile strain of the composite were improved by up to 45% and 23%, compared with those of the forged alloy in similar regions. These enhancements were respectively 50% and 37% in the compression test. The composite exhibited a fatigue life improvement in the region with low applied strain;however, a degradation was observed in the high applied strain region. Unlike AZ31 B samples, tensile, compressive and high cycle fatigue behaviors of the composite showed less sensitivity to the applied strain, which can be attributed to the amount of porosity in the samples before and after the hot-forging.

Electrochemical Hydrogen Storage Performances of the Si Added La-Mg-Ni-based A_2B_7-type Electrode Alloys for Ni/MH Battery Application

The casting and annealing technologies were applied to fabricate the La0.8Mg0.2Ni3.3Co0.2Six （x = 0-0.2） electrode alloys. The effects of Si content and annealing temperature on the structure and electrochemical performances of the alloys were investigated systematically. The analyses of XRD and SEM show that all the alloys possess a multiphase structure, involving two main phases （La, Mg）2Ni7 and LaNi5 as well as a residual phase LaNi3. The addition of Si brings on an evident increase in the LaNi5 phase and a decrease in the （La, Mg）2Ni7 phase, without altering the main phase component of the alloy, which also makes the lattice constants and cell volumes of the alloy enlarged. Likewise, the annealing treatment engenders the same action on the lattice constants and cell volumes as adding Si. Simultaneously, it gives rise to the variation of the phase abundance and the coarsening of the alloy grains. The electrochemical measurements indicate that the addition of Si ameliorates the cycle stability of the as-cast and annealed alloys significantly, but impairs their discharge capacities clearly. Similarly, the annealing treatment makes a positive contribution to the cycle stability of the alloy evidently, and the discharge capacity of the alloy shows a maximum value with annealing temperature rising. Furthermore, the high rate discharge ability （HR） first augments and then declines with the rising of Si content and annealing temperature.

Structure and Electrochemical Properties of A_2B_7-Type La-Mg-Ni Hydrogen Storage Alloys

Investigation of alloy structure shows that La2-xMgxNi7 （x = 0.3 - 0.8） alloys are mainly com- posed of Ce/Ni7-type, Gd2Co7-type and PuNi3-type phase. The influence of Mg content in alloys on the phase structure is great, resulting in a linear decrease of the unit cell parameters of main phases and increase of hydrogen absorption/desorption plateau as Mg content increases. Electrochemical measurements show that as the Mg content increases, the discharge capacity of alloy electrodes first increases and then decreases. The cyclic stability presents a deteriorative trend. La1.4Mg0.6 Ni7 alloy electrode exhibits the maximum electrochemical discharge capacity （378 mAh·g^-1）, and the La1.6Mg0.4Ni7 alloy electrode shows the best cyclic stability （S270 = 81%）.

Structures and electrochemical performances of La_(0.75-x)Zr_xMg_(0.25)Ni_(3.2)Co_(0.2)Al_(0.1) (x=0-0.2) electrode alloys prepared by melt spinning

The La-Mg-Ni system A2B7-type electrode alloys with nominal composition La0.75-xZrxMg0.25Ni3.2Co0.2Al0.1(x=0,0.05, 0.1,0.15,0.2)were prepared by casting and melt-spinning.The influences of melt spinning on the electrochemical performances as well as the structures of the alloys were investigated.The results obtained by XRD,SEM and TEM show that the as-cast and spun alloys have a multiphase structure,consisting of two main phases(La,Mg)Ni3 and LaNi5 as well as a residual phase LaNi2.The melt spinning leads to an obvious increase of the LaNi5 phase and a decrease of the(La,Mg)Ni3 phase in the alloys.The results of the electrochemical measurement indicate that the discharge capacity of the alloys(x≤0.1)first increases and then decreases with the increase of spinning rate,whereas for x>0.1,the discharge capacity of the alloys monotonously falls.The melt spinning slightly impairs the activation capability of the alloys,but it significantly enhances the cycle stability of the alloys.

TEMPERATURE DEPENDENCE OF PERMEABILITY OF Co_(66)Fe_4Mo_2Si_(16)B_(12) ALLOY

At different annealing temperatures, the saturation magnetostrictions and the correlation between the permeability μi and the temperature T （μi-T curves） of the Co66Fe4Mo2Si16B12 alloy were investigated using a small-angle magnetization tester and core tester. The experimental results showed that the μi-T curves had different shapes at different ranges of annealing temperature; the permeability μi of the alloy improved with the increase of the annealing temperatures below 460℃; when the alloy was annealed above 480℃, the poor magnetic properties were considered to be caused by larger saturation magnetostriction.

Laser Cladding Al-Si/Al_2O_3-TiO_2 Composite Coatings on AZ31B Magnesium Alloy

To improve the wear resistance and corrosion resistance of magnesium alloys, a 5 kW continuous wave CO2 laser was used to investigate the laser surface cladding on AZ31 B magnesium alloys with Al-Si/Al2O3-TiO2 composite powders. A detailed microstructure, chemical composition, and phase analysis of the composite coatings were studied by scanning electron microscopy （SEM）, energy dispersive spectroscopy （EDS）, and X-ray diffraction （XRD）. The laser cladding shows good metallurgical bonding with the substrate. The composite coatings are composed of Mgl7Al12, Al3Mg2, Mg2Si, Al2O3, and TiO2 phases. Compared to the average microhardness （50HV0.05） of the AZ3 1 B substrate, that of the composite coatings （230HV0.05） is improved significantly. The wear resistances of the surface layers were evaluated in detail. The results demonstrate that the wear resistances of the laser surface-modified samples are considerably improved compared to the substrate. It also show that the composite coatings exhibit better corrosion resistance than that of the substrate in 3.5wt% NaCI solution.

As-cast Ti_(x)(AlVCr)_(100−x)light-weight medium entropy alloys with high strength and uniform compressive plasticity

The effect of Ti content on the microstructure and mechanical properties of as-cast light-weight Ti_(x)(AlVCr)_(100−x)medium entropy alloys was studied by compressive tests,X-ray diffraction,scanning electron microscopy and transmission electron microscopy.The results suggest that yield strength increases and then decreases with the increment of Ti content.The Ti_(60)(AlVCr)_(40)alloy has the best combination of high strength of 1204 MPa and uniform plastic strain of 70%,possessing a high specific yield strength of 255 MPa·cm^(3)/g.The enhancement of strength is mainly attributed to the synergic effects of solid-solution and coherent nano-precipitation strengthening,while dislocation motion such as dislocation pinning,entanglement and dislocation cells significantly increases the strain-hardening capacity.

INTERMEDIA TETEMPERATURE STRESS ANOMALY IN B_2 ALLOYS: WITH SPECIAL ATTENTION TO THE CASE OF IRON ALUMINIDES

The iron aluminides show anomalous stress peaks at temperatures of the order of 400～600 ℃, irrespective of whether the crystal structure is B2 type or DO 3 type. Such features will be examined on the basis of thermally activated dislocation processes, considering the influence of test parameters such as temperature and strain rate, and material parameters such as crystal composition and orientation. Detailed analyses of deformation modes by slip step studies, transmission electron microscopy examinations of dislocation structures, and texture studies will also be considered. Observations of dislocation structures are clearly of great interest for suggesting the possible models of deformation, but suffer from two major weaknesses: the post mortem structures in samples deformed at high temperature may not be the same as those producing plasticity; almost all possible hypotheses for strengthening can find support from such observations, since almost all imaginable dislocation configurations can be found with sufficient diligence by the researcher. Strengthening at intermediate temperatures in DO 3 and B2 ordered iron aluminides will be analysed here, making combined use of observations of deformation structures and examinations of the influence of varying the deformation parameters.

Relations among High-frequency Magnetic Properties and Frequency in Nanocrystalline Fe_(72.5)Cu_1Nb_2V_2Si_(13.5)B_9 Alloy

High-frequency magnetic properties, such as core loss, coercivity and amplitude permeabilityof a newly-developed nanocrystalline Fe72.5Cu1Nb2V2Si13.5B9 alloy in the wide ranges of f =20-103 kHz, Bm = 0.01~0.6 T and Bmf = 10~40 (T.kHz) have been measured. A largeamount of experimental data have been fitted by a computer, thus obtaining several expressionsrepresenting the influence of frequency on high-frequency magnetic properties, that are useful inpractical applications.

Impacts of Melt Spinning and Element Substitution on Electrochemical Characteristics of the La–Mg–Ni-based A₂B₇-Type Alloys

The partial substitution of Zr for La has been performed in order to ameliorate the electrochemical hydrogen storage performances of La–Mg–Ni based A2B7-type electrode alloys. The melt spinning technology was used to prepare the La0.75-xZrxMg0.25Ni3.2Co0.2Al0.1 (x=0, 0.05, 0.1, 0.15, 0.2) electrode alloys. The impacts of the melt spinning and the substituting La with Zr on the structures and the electrochemical hydrogen storage characteristics of the alloys were systemically investigated. The analysis of XRD and TEM reveals that the as-cast and spun alloys have a multiphase structure, composing of two main phases (La, Mg)2Ni7 and LaNi5 as well as a residual phase LaNi2. The electrochemical measurement indicates that both the substitution of Zr for La and the melt spinning ameliorate the electrochemical cycle stability of the alloys dramatically. Furthermore, the high rate discharge ability (HRD) of the as-spun (10 m/s) alloys notably declines with growing the amount of Zr substitution, while it first augments and then falls for the (x=0.1) alloy with rising the spinning rate.

Tuning mechanical properties for β(B2)-containing TiAl intermetallics

Based on the analyses of the microstructures and phase diagrams of the TiAl-based alloy, the relationship among the composition, structure and mechanical properties of the B2-containing y-TiAI alloys was reviewed. The refinement of microstructures and improvement of mechanical properties of TiA1 alloy through stabilization of the β/B2 phase were reviewed. The mechanism of the superplastic behavior of the B2-containing y-TiAI alloys was discussed. With a reasonable addition of β-stabilizer, metastable B2 phase can be maintained, which is favorable for fine-grained structure and better high-temperature deformation behaviors. The mechanical properties of the B2-containing TiAI alloy, including the deformability and elevated temperature properties, can also be improved with doping elements and subsequent hot-working processes. The above mentioned researches discuss a new way for developing TiAI alloys with comprehensive properties, including good deformability and creep resistance.

Electrochemical hydrogen storage characteristics of as-cast and annealed La_(0.8-x)Nd_xMg_(0.2)Ni_(3.15)Co_(0.2)Al_(0.1)Si_(0.05)(x=0-0.4)alloys

The La-Mg-Ni-based A2B7-type La0.8-xNdxMg0.2Ni3.15Co0.2Al0.15 （x=0, 0.1, 0.2, 0.3, 0.4） electrode alloys were prepared by casting and annealing. The influences of partial substitution of Nd for La on the structure and electrochemical performance of the as-cast and annealed alloys were investigated. It was found that the experimental alloys consist of two major phases, （La, Mg）2Ni7 phase with the hexagonal Ce2Ni7-type structure and LaNi5 phase with the hexagonal CaCu5-type structure, as well as some residual phase LaNi3 and NdNi5. The discharge capacity and high rate discharge ability （HRD） of the as-cast and annealed alloys first increase and then decrease with Nd content growing. The as-cast and annealed alloys （x=0.3） yield the largest discharge capacities of 380.3 and 384.3 mA·h/g, respectively. The electrochemical cycle stability of the as-cast and annealed alloys markedly grows with Nd content rising. As the Nd content increase from 0 to 0.4. The capacity retaining rate （S100） at the 100th charging and discharging cycle increases from 64.98% to 85.17% for the as-cast alloy, and from 76.60% to 96.84% for the as-annealed alloy.

PCNA和Bcl-2蛋白在牙龈组织中的表达

给实验动物狗分别行金合金、不含Be的镍铬合金、含Be的镍铬合金全冠修复,建立实验动物模型.采用ICP-MS(电感耦合等离子体质谱仪)检测戴冠前后牙龈组织中金属离子的质量分数,同时应用免疫组化EnVision二步法检测PCNA(增殖细胞核抗原)、Bcl-2(B细胞白血病/淋巴瘤基因2)蛋白在牙龈组织中的表达.结果表明,镍铬合金全冠戴用后,牙龈组织PCNA,Bcl-2蛋白表达明显,而金合金全冠戴用后表达不明显.PCNA蛋白表达率与Ni,Cr,Si及Be离子质量分数正相关,而Bcl-2蛋白表达率与离子质量分数无明显的相关性.

负载型非晶态Ni-B/SiO_2合金对芥酸加氢催化性能研究

研究了负载型非晶态Ni B/SiO2 合金催化剂对芥酸加氢制备山嵛酸的催化性能。结果表明 ,Ni B/SiO2 对芥酸加氢具有很高的活性 ,且稳定性较高 ,其催化性能优于非负载Ni B非晶态合金和RaneyNi催化剂。

Y_2O_3对WC-B_4C激光合金化层裂纹与耐磨性能的影响

目前,有关稀土氧化物粉末粒度大小及含量对激光陶瓷合金化层裂纹及耐磨性能影响的研究较少。以近纳米级Y2O3-WC-B4C粉末对60CrMnMo钢表面进行激光陶瓷合金化,以提高其耐磨性能。采用金相显微镜、扫描电镜、X射线衍射仪、显微硬度计、轮式磨耗试验机分析、考察了Y2O3含量对合金化层的组织、物相、硬度及耐磨性能的影响。结果表明:Y2O3使合金化层表面更加平整、光滑,表面裂纹减少、变细;合金化层硬度随着Y2O3含量增加而降低;合金化层物相主要有Fe-Cr,Cr23C6,B2W,B13C2等;随Y2O3含量增加,树枝晶减少,合金化层组织更均匀致密,磨损量先减小后增大;Y2O3含量为4%时,合金化层组织最细、耐磨性最好。