A Current-Mode DC-DC Buck Converter with High Stability and Fast Dynamic Response

A current-mode DC-DC buck converter with high stability is presented. The loop gain＇s expression of the current-mode converter is derived by employing an advanced model of a current-mode control converter. After analyzing the loop gain＇s expression, which illustrates the method of selecting suitable frequency compensation for the control loop,a novel pole-zero tracking frequency compensation is proposed. Based on theoretical analysis, a DC-DC buck converter with high stability is designed with 0.5μm-CMOS technology. The simulated results reveal that the stability of the converter is independent of the load current and the input voltage. Moreover,the converter provides a full load transient response setting time of less than 5μs and overshoots and undershoots of less than 30mV.

A low noise high efficiency buck DC-DC converter with sigma-delta modulation

Some research efforts to improve the efficiency and noise performance of buck DC-DC converters are explored.A carefully designed power MOSFET driver,including a dead time controller,discontinuous current mode（DCM） controller and gate width controller,is proposed to improve efficiency.Instead of PWM modulation, sigma-delta modulation is introduced into the feedback loop of the converter to move out the clock-referred harmonic spike.The proposed converter has been designed and fabricated by a 0.35μm CMOS process.Measured results show that the peak efficiency of the converter can reach 93%and sigma-delta modulation suppresses the harmonic spike by 30 dB over PWM modulation.

DCM,FSM,dead time and width controllers for a high frequency high efficiency buck DC-DC converter over a wide load range

This paper presents a width controller,a dead time controller,a discontinuous current mode（DCM） controller and a frequency skipping modulation（FSM） controller for a high frequency high efficiency buck DC-DC converter. To improve the efficiency over a wide load range,especially at high switching frequency,the dead time controller and width controller are applied to enhance the high load efficiency,while the DCM controller and FSM controller are proposed to increase the light load efficiency.The proposed DC-DC converter controllers have been designed and fabricated in the Chartered 0.35μm CMOS process,and the measured results show that the efficiency of the buck DC-DC converter is above 80%over a wide load current range from 8 to 570 mA,and the peak efficiency is 86%at 10 MHz switching frequency.

A high-efficiency transformer-in-package isolated DC-DC converter using glass-based fan-out wafer-level packaging

A transformer-in-package(TiP)isolated direct current-direct current(DC-DC)converter using glass-based fan-out wafer-level packaging(FOWLP)is proposed.By using 3-layer redistribution layers(RDLs),both the transformer and interconnections are built without an additional transformer chip,and the converter only has 2 dies:a transmitter(TX)chip and a receiver(RX)chip.The proposed solution results in a significant reduction in the cost and makes major improvements in the form factor and power density.Moreover,the transformer built by the RDLs achieves a high quality factor(Q)and high coupling factor(k),and the efficiency of the converter is thus improved.The TX and RX chips were implemented in a 0.18μm Biopolar CMOS DMOS(BCD)process and embedded in a compact package with a size of 5 mm×5 mm.With an output capacitance of 10μF,the converter achieves a peak efficiency of 46.5%at 0.3 W output power and a maximum delivery power of 1.25 W,achieving a maximum power density of 50 mW/mm2.

ANovel Non-Isolated Cubic DC-DC Converter with High Voltage Gain for Renewable Energy Power Generation System

In recent years,switched inductor(SL)technology,switched capacitor(SC)technology,and switched inductor-capacitor(SL-SC)technology have been widely applied to optimize and improve DC-DC boost converters,which can effectively enhance voltage gain and reduce device stress.To address the issue of low output voltage in current renewable energy power generation systems,this study proposes a novel non-isolated cubic high-gain DC-DC converter based on the traditional quadratic DC-DC boost converter by incorporating a SC and a SL-SC unit.Firstly,the proposed converter’s details are elaborated,including its topology structure,operating mode,voltage gain,device stress,and power loss.Subsequently,a comparative analysis is conducted on the voltage gain and device stress between the proposed converter and other high-gain converters.Then,a closed-loop simulation system is constructed to obtain simulation waveforms of various devices and explore the dynamic performance.Finally,an experimental prototype is built,experimental waveforms are obtained,and the experimental dynamic performance and conversion efficiency are analyzed.The theoretical analysis’s correctness is verified through simulation and experimental results.The proposed converter has advantages such as high voltage gain,low device stress,high conversion efficiency,simple control,and wide input voltage range,achieving a good balance between voltage gain,device stress,and power loss.The proposed converter is well-suited for renewable energy systems and holds theoretical significance and practical value in renewable energy applications.It provides an effective solution to the issue of low output voltage in renewable energy power generation systems.

Design of Second Order Sliding Mode and Sliding Mode Algorithms:A Practical Insight to DC-DC Buck Converter

This paper presents a simple and systematic approach to design second order sliding mode controller for buck converters.The second order sliding mode control(SOSMC)based on twisting algorithm has been implemented to control buck switch mode converter.The idea behind this strategy is to suppress chattering and maintain robustness and finite time convergence properties of the output voltage error to the equilibrium point under the load variations and parametric uncertainties.In addition,the influence of the twisting algorithm on the performance of closed-loop system is investigated and compared with other algorithms of first order sliding mode control such as adaptive sliding mode control(ASMC),nonsingular terminal sliding mode control(NTSMC).In comparative evaluation,the transient response of the output voltage with the step change in the load and the start-up response of the output voltage with the step change in the input voltage of buck converter were compared.Experimental results were obtained from a hardware setup constructed in laboratory.Finally,for all of the surveyed control methods,the theoretical considerations,numerical simulations,and experimental measurements from a laboratory prototype are compared for different operating points.It is shown that the proposed twisting method presents an improvement in steady state error and settling time of output voltage during load changes.

Pole placement method of controlling chaos in DC-DC buck converters

Based on the mechanism for the generation of chaos in a buck converter, a pole placement method is proposed and applied to controlling the chaos in a circuit. The control circuit is designed and tested. Numerical calculation and circuit implementation demonstrate the validity of this chaos control method.

Study of Sliding Mode Control of DC-DC Buck Converter

In this paper, a robust sliding mode controller for the control of dc-dc buck converter is designed and analyzed. Dynamic equations describing the buck converter are derived and sliding mode controller is designed. A two-loop control is employed for a buck converter. The robustness of the sliding mode controlled buck converter system is tested for step load changes and input voltage variations. The theoretical predictions are validated by means of simulations. Matlab/Simulink is used for the simulations. The simulation results are presented. The buck converter is tested with operating point changes and parameter uncertainties. Fast dynamic response of the output voltage and robustness to load and input voltage variations are obtained.

Direct Model Predictive Control of Noninverting Buck-boost DC-DC Converter

In this paper, direct model predictive control(DMPC) of the noninverting buck-boost DC-DC converter with magnetic coupling between input and output is proposed. Unlike most of the other converters, the subject converter has the advantage of exhibiting minimum phase behavior in the boost mode. However, a major issue that arises in the classical control of the converter is the dead zone near the transition of the buck and boost mode. The reason for the dead zone is practically unrealizable duty cycles, which are close to zero or unity, of pulse width modulation(PWM) near the transition region. To overcome this issue, we propose to use DMPC. In DMPC, the switches are manipulated directly by the controller without the need of PWM.Thereby, avoiding the dead zone altogether. DMPC also offers several other advantages over classical techniques that include optimality and explicit current constraints. Simulations of the proposed DMPC technique on the converter show that the dead zone has been successfully avoided. Moreover, simulations show that the DMPC technique results in a significantly improved performance as compared to the classical control techniques in terms of response time, reference tracking, and overshoot.

A Piecewise Linear Slope Compensation Circuit for DC-DC Converters

To prevent sub-harmonic oscillation and improve the stability and load capacity of the system,a piecewise linear slope compensation circuit is designed. Compared with the traditional design, this circuit provides a compensation signal whose slope varies from different duty cycles at - 40-85℃ ,and reduces the negative effect of slope compensation on the system＇s load capacity and transient response. A current mode PWM Boost DC-DC converter employing this slope compensation circuit is implemented in a UMC 0.6μm-BCD process. The results indicate that the circuit works well and effectively,and the load capacity is increased by 20%. The chip area of the piecewise linear slope compensation circuit is 0.01mm^2 ,which consumes only 8μA quiescent current,and the efficiency ranges up to 93%.

SIMULATION STUDY OF CHAOS IN DC-DC CONVERTER

A DC DC buck converter c on trolled by naturally sampled, constant frequency PWM is considered. The existe nce of chaotic solutions and the output performance of the system under differen t circuit parameters are studied. The transforming pattern of system behavior fr om steady state to chaotic is discovered by the cascades of period doubling bi furcation and the cascades of periodic orbit in V I phase space. Accordingl y, it is validated that change of values of the circuit parameters may lead DC DC converter to chaotic motion. Performances of the output ripples fro m steady state to chaotic are analyzed in time and frequency domains respective ly. Some important conclusions are helpful for opt imization design of DC DC converter.

Improving Characteristics of Integrated Switched-Capacitor DC-DC Converter by CMOS Technology

An integrated 3.3V/1.2V SC DC-DC converter operating under 10MHz with a fixed duty radio of 0.5 is presented.To improve the output current of the converter,CMOS technology is adopted to fabricate the switching devices,and mutually compensatory circuitry technology is also employed to double the output current furthermore.The simulation results using Hspice simulation software,show that the output currents of a single unit circuit and two unit circuits connected in a mutually compensatory manner of the improved converter is about 12.5mA and 26mA,respectively.The power conversion efficiency of the mutually compensatory circuit can amount to 73%,while its output voltage ripple is less than 1.5%.The converter is fabricated in standard Rohm 0.35μm CMOS technology in Tokyo University of Japan.The test result indicates that the output current of 9.8mA can be obtained from a single unit circuit of the improved converter.

A Novel Hybrid DPWM for Digital DC-DC Converters

We present a new hybrid digital pulse-width modulator （DPWM） for digital DC-DC converters that employs a ring-oscillator/counter structure. Based on a temperature/process compensation technique and a novel digital controller, the proposed DPWM can not only offer temperature/process-independent pulse widths, but also operate at a much higher clock frequency than the existing delay-line/counter DPWM structure. Post-simulation results show that with our DPWM, the system clock frequency reaches 156.9MHz while the worst variation,in a temperature range of 0 to 100℃under all process corners,is only± 9.4%.

Transfer function modeling and analysis of the open-loop Buck converter using the fractional calculus

Based on the fact that the real inductor and the real capacitor are fractional order in nature and the fractional calculus,the transfer function modeling and analysis of the open-loop Buck converter in a continuous conduction mode（CCM） operation are carried out in this paper.The fractional order small signal model and the corresponding equivalent circuit of the open-loop Buck converter in a CCM operation are presented.The transfer functions from the input voltage to the output voltage,from the input voltage to the inductor current,from the duty cycle to the output voltage,from the duty cycle to the inductor current,and the output impedance of the open-loop Buck converter in CCM operation are derived,and their bode diagrams and step responses are calculated,respectively.It is found that all the derived fractional order transfer functions of the system are influenced by the fractional orders of the inductor and the capacitor.Finally,the realization of the fractional order inductor and the fractional order capacitor is designed,and the corresponding PSIM circuit simulation results of the open-loop Buck converter in CCM operation are given to confirm the correctness of the derivations and the theoretical analysis.

Dynamical analysis and experimental verification of valley current controlled buck converter

The dynamical behaviours of valley current controlled buck converter are studied by establishing its corresponding discrete iterative map model in this paper. Time-domain waveforms and phase portraits of valley current controlled buck converter are obtained by Runge-Kutta algorithm through a piecewise smooth switching model. The research results indicate that the valley current controlled buck converter exhibits rich nonlinear phenomena, and it has routes to chaos through period-doubling bifurcation and border-collision bifurcation in a wide parameter range. Interesting inverse nonlinear behaviours compared with peak current controlled buck converter are observed in the valley current controlled buck converter. Analysis and simulation results are verified by experimental results.

Dynamics and stabilization of peak current-mode controlled buck converter with constant current load

The discrete iterative map model of peak current-mode controlled buck converter with constant current load（CCL）,containing the output voltage feedback and ramp compensation, is established in this paper. Based on this model the complex dynamics of this converter is investigated by analyzing bifurcation diagrams and the Lyapunov exponent spectrum. The effects of ramp compensation and output voltage feedback on the stability of the converter are investigated. Experimental results verify the simulation and theoretical analysis. The stability boundary and chaos boundary are obtained under the theoretical conditions of period-doubling bifurcation and border collision. It is found that there are four operation regions in the peak current-mode controlled buck converter with CCL due to period-doubling bifurcation and border-collision bifurcation. Research results indicate that ramp compensation can extend the stable operation range and transfer the operating mode, and output voltage feedback can eventually eliminate the coexisting fast-slow scale instability.

Modeling the System for Hybrid Renewable Energy Using Highly Efficient Converters and Generator

High-efficient isolated DC/DC converters with a high-efficiency synchronous reluctance generator(SRG)are the ultimate solutions in DC microgrid systems.The design and modeling of isolated DC/DC converters with the performance of SRG are carried out.On the generator side,reactive and active powers are used as pulse width modulation(PWM)control variables.Further,the flux estimator is used.Three-phase PWM rectifier is used by applying space vector modulation(SVM)with a constant switching frequency for direct power control.Further,the paper also includes the experimental validation of the results.The paper also proposes that highly efficient power converters and synchronous reluctance generators are required to achieve high performance for hybrid renewable energy systems applications.

A high performance adaptive on-time controlled valley-current-mode DC–DC buck converter

This paper presents an AOT-controlled(adaptive-on-time,AOT)valley-current-mode buck converter for portable application.The buck converter with synchronous rectifier not only uses valley-current-mode control but also possesses hybridmode control functions at the same time.Due to the presence of the zero-current detection circuit,the converter can switch freely between the two operating modes without the need for an external mode selection circuit,which further reduces the design difficulty and chip area.The converter for the application of high power efficiency and wide current range is used to generate the voltage of 0.6–3.0 V with a battery source of 3.3–5.0 V,while the load current range is 0.05–2 A.The circuit can work in continuous conduction mode with constant frequency in high load current range.In addition,a stable output voltage can be obtained with small voltage ripple.In pace with the load current decreases to a critical value,the converter transforms into the discontinuous conduction mode smoothly.As the switching period increases,the switching loss decreases,which can significantly improve the conversion efficiency.The proposed AOT controlled valley current mode buck converter is integrated with standard 0.18μm process and the simulation results show that the converter provides well-loaded regulations with power efficiency over 95%.When the circuit switches between the two conduction modes drastically,the response time can be controlled within 30μs.The undershoot voltage is controlled within 25 mV under a large current hopping range.

Effects of electron radiation on commercial power MOSFET with buck converter application

Microelectronic power converters such as buck and boost converter are required to be tolerant to radiations including electron radiation. This paper examines electron radiation effects on the Ⅰ-Ⅴ characteristics of VDMOSFET and its corresponding effects in buck converter. Analysis of the electrical characteristics shows that after irradiation the threshold voltage and drain current for all VDMOSFETs degraded more than two orders of magnitude. The impact of this electrical degradation has been investigated in an application of typical buck converter circuit. The buck converter with n-channel switching transistor shows that after irradiation its output voltage increased with the drain current in the n-channel ZVN4424 A VDMOSFET, while the buck converter with p-channel switching transistor shows its output voltage decreased with the drain current in the p-channel ZVP4424 A VDMOSFET after irradiation.

Notch filter feedback controlled chaos in buck converter

A method of controlling chaos in the voltage-mode buck converter is presented by using an improved notch filter feedback control in this paper. The proposed control part comprises a notch filter and a low-pass filter. The discrepancy between the outputs of the two filters is introduced into the control prototype of the power converter. In this way, the system period-1 solution is kept unchanged. The harmonic balance method is applied to analysing the variation law of the system bifurcation point, and then the stable range of the feedback gain is ascertained. The results of simulation and experiment are also given finally.