Effect of Sinter Hardening on Microstructure and Mechanical Properties of Astaloy 85Mo

Effect of sinter hardening on the microstructure, density, hardness and tensile properties of Astaloy 85Mo+0.7% graphite was investigated. For this purpose, Astaloy 85Mo, a pre-alloyed powder, was mixed with 0.7% UF4 graphite and then pressed in single action die and sintered at 1 120 ℃ for 30 min in N2-10%H2 atmosphere. Then samples were cooled from 0.5 to 3 ℃/s sintering temperature in accordance with different cooling rates. The difference in microstructure, hardness, density and tensile properties of the samples associated with different cooling rates from sintering temperature has been investigated. The results show that the microstructure remains bainitic by changing cooling rate, but it becomes finer and then the hardness and tensile strength of the samples will increase by increasing the cooling rate from sintering temperature.

Mechanical properties of a microalloyed bainitic steel after hot forging and tempering

Mechanical properties of a newly developed microalloyed bainitic steel were investigated after the hot forging, air cooling and tempering process. The microstructure of the as forged bainitic steel mainly consists of granular bainite and -20 vol. % martensite. The fraction of retained austenite remains unchanged until tempering at 200 ℃, above which it decreases significantly. The increase of tempering temperature leads to decreases of both ultimate tensile strength and total elongation but decreases of both yield strength and reduction of area. The maximum and mini- mum values of impact toughness were observed after tempering at around 200 and 400 ℃, respectively. These effects are mainly attributed to the decomposition of martensite/austenite con stituents and the tempering effects in martensite. The tempering of the forged bainitic steel at around 200 ℃ results in an excellent combination of strength and toughness, which is comparable to that of the conventional quenched and-tempered 40Cr steel. Therefore, low-tempering treatment coupled with post-forging residual stress relieving is a feasible method to further improve the mechanical prooerties of the bainitic foging steel.

Weldability of 1000 MPa Grade Ultra-low Carbon Bainitic Steel

Maximum hardness test in weld heat-affected zone（HAZ）,oblique Y-groove cracking test and mechanical property test of welding joint of 1 000 MPa grade ultra-low carbon bainitic steel were carried out,so as to research the weldability of the steel.The results show that the steel has lower cold cracking sensitivity,and preheating temperature of 100 ℃ can help completely eliminate cold cracks,generating good process weldability.The increase of preheating temperature can reduce the hardening degree of heat-affected zone.The strength of welding joint decreases and hardness reduces when heat inputs increase,and excellent mechanical properties can be obtained when low welding heat inputs are used.Fine lath bainites of different orientations combined with a few granular bainites that effectively split the original coarse austenite grains are the foundation of good properties.

Role of Solute Rare Earth in Altering Phase Transformations during Continuous Cooling of a Low Alloy Cr–Mo–V Steel

Effects of solute rare earth(RE)on continuous cooling transformation of a low-alloy Cr–Mo–V bainitic steel are investigated in detail by dilatometry,optical microscopy(OM),scanning electron microscopy(SEM)and transmission electron microscopy(TEM).Microstructures appeared in thermal dilatometric samples of both low-alloy Cr–Mo–V(RE)steels are composed of quasi-polygonal ferrite(QPF),degenerate pearlite(DP),granular bainite(GB),lath bainite(LB),and martensite(M)depending on cooling rate.When cooling rate is lower than 2°C/s,the addition of RE suppresses QPF transformation,and thereby inducing a broader transformation region of GB.When cooling rate ranges from 2 to 100°C/s,the addition of RE decreases the start temperature of bainitic transformation distinctly,which results in finer bainitic ferrite grain size and higher dislocation density.The addition of RE can enhance the hardness of the low alloy Cr–Mo–V steel by affecting the aforementioned diffusional and/or partly displacive transformation.However,when cooling rate increases up to 150°C/s,two steels have the same hardness value of about 435 HV due to only martensite obtained by displacive transformation.