Adhesive for bamboo plywood prepared directly using lignin existing in the black liquor as a kind of material replacing phenol was proposed on the basis of the same structural properties of lignin and phenol. The resu...Adhesive for bamboo plywood prepared directly using lignin existing in the black liquor as a kind of material replacing phenol was proposed on the basis of the same structural properties of lignin and phenol. The results indicate that the reaction time of black liquor methylating is 30min, when the ratio of alkali to formaldehyde is controlled at approximately 0.20, decomposition rate of formaldehyde is the lowest and the effect of black liquor methylating is the best, the optimal molar ratio of phenol： formaldehyde to NaOH to H2O of preparing phenolic resin is 1.00 ： 1.50 ： 0.50 ： 9.00, and the suitable viscosity is 27 - 30 Pa· s. At different mass ratios of methylated black liquor to phenolic resin, all terms of performance of black liquor phenolic resin are excellent and satisfy the requirement. All terms of performance of bamboo plywood prepared using this technique are hetter than that of excellent bamboo plywood of national criteria. Using this technique, the cost is depressed by 28.69% without altering the traditional adhesive producing technique flow, and without using additional equipment.展开更多
The acoustic emission(AE)technique can perform non-destructive monitoring of the internal damage development of bamboo and wood materials.In this experiment,the mechanical properties of different bamboo and wood(bambo...The acoustic emission(AE)technique can perform non-destructive monitoring of the internal damage development of bamboo and wood materials.In this experiment,the mechanical properties of different bamboo and wood(bamboo scrimber,bamboo plywood and SPF(Spruce-pine-fir)dimension lumber)during four-point loading tests were compared.The AE activities caused by loadings were investigated through the single parameter analysis and K-means cluster analysis.Results showed that the bending strength of bamboo scrimber was 3.6 times that of bam-boo plywood and 2.7 times that of SPF dimension lumber,respectively.Due to the high strength and toughness of bamboo,the AE signals of the two bamboo products were more abundant than those of SPF dimension lumber.However,the AE evolution trend of the three materials was similar,which all experienced three stages,including gentle period,steady period and steep period,and the area of rupture precursor characteristics could be recognized before the specimen destroyed.Due to the bottom layer was first tensile failure,the main structure of bamboo plywood was destroyed after the stress redistribution.The rupture precursor characteristics could be observed before each peak.Findings put in evidence a good correlation between AE clusters of two bamboo products,while the amplitude and energy of wood signals were lower than those of bamboo.The amplitude and energy from the propagation and aggregation of cracks were greater than those related to micro-cracks initiation.展开更多
The steel-bamboo composite structure is a newly developed structure,combining phyllostachys pubescens(also called Moso bamboo)plywood and cold-formed thin-walled steel with structural adhesive.The reliability of steel...The steel-bamboo composite structure is a newly developed structure,combining phyllostachys pubescens(also called Moso bamboo)plywood and cold-formed thin-walled steel with structural adhesive.The reliability of steelbamboo interface is the premise of composite effect.13 specimens were prepared to investigate the failure modes and mechanism of the steel-bamboo interface on the basis of push-out test,and the strain difference analysis method was proposed to study the distribution of shear stress.The results show that the main failure modes of steel-bamboo interface are adhesion failure and splitting of bamboo plywood.The shear stress is not evenly distributed along the longitudinal direction of the interface,showing a shape of“larger at two ends and smaller in the middle”.The lower end of the interface is the initial location of the interface failure and the shear stress concentration degree is positively correlated with the thickness of the externally bonded bamboo plate.The shear resistance of steel-bamboo interface can be enhanced by improving the adhesion between steel and structural adhesive and ameliorating the quality of bamboo products.展开更多
采用冷弯薄壁方型钢管和胶合竹板通过横向约束拉杆和结构胶黏剂复合成顺纹抗压的组合空芯短柱(thin-walled steel tube/bamboo-plywood composite hollow short column with binding bars,SBCCB),采用9个试件研究SBCCB试件的偏心抗压破...采用冷弯薄壁方型钢管和胶合竹板通过横向约束拉杆和结构胶黏剂复合成顺纹抗压的组合空芯短柱(thin-walled steel tube/bamboo-plywood composite hollow short column with binding bars,SBCCB),采用9个试件研究SBCCB试件的偏心抗压破坏模式、抗压承载力和影响规律。结果表明,SBCCB试件受压破坏形态主要为柱端开胶破坏、横向约束拉杆之间基体胶合界面开胶剥离破坏和胶合竹板局部压屈破坏;SBCCB抗压极限荷载随胶合竹净横截面积增大而提高,随着长细比和荷载偏心率的增大而降低,随空心率增大而增大;约束拉杆可有效延迟SBCCB的开胶剥离破坏,改变屈曲破坏模式,有助于试件抗压承载力的提高;相对于不带约束拉杆试件,SBCCB抗压极限应力提高约17.64%;局部翘曲随约束拉杆间距减小而减小,相对拉杆间距比3.0以下能确保较小的局部翘曲变形。薄壁钢管和胶合竹板能形成较好的复合抗压结构单元,该批试件平均值抗压强度达到18.54 MPa,展现了优异的抗压性能。SBCCB可作为绿色建筑材料广泛应用于现代装配式工程结构,同时拓展竹材的应用途径,实现"以竹代木,以竹代钢",具有很好的工程价值和应用前景。展开更多
文摘Adhesive for bamboo plywood prepared directly using lignin existing in the black liquor as a kind of material replacing phenol was proposed on the basis of the same structural properties of lignin and phenol. The results indicate that the reaction time of black liquor methylating is 30min, when the ratio of alkali to formaldehyde is controlled at approximately 0.20, decomposition rate of formaldehyde is the lowest and the effect of black liquor methylating is the best, the optimal molar ratio of phenol： formaldehyde to NaOH to H2O of preparing phenolic resin is 1.00 ： 1.50 ： 0.50 ： 9.00, and the suitable viscosity is 27 - 30 Pa· s. At different mass ratios of methylated black liquor to phenolic resin, all terms of performance of black liquor phenolic resin are excellent and satisfy the requirement. All terms of performance of bamboo plywood prepared using this technique are hetter than that of excellent bamboo plywood of national criteria. Using this technique, the cost is depressed by 28.69% without altering the traditional adhesive producing technique flow, and without using additional equipment.
基金This paper was supported in part by Project funded by the National Natural Science Foundation of China(Grant Nos.32071700 and 31570559).
文摘The acoustic emission(AE)technique can perform non-destructive monitoring of the internal damage development of bamboo and wood materials.In this experiment,the mechanical properties of different bamboo and wood(bamboo scrimber,bamboo plywood and SPF(Spruce-pine-fir)dimension lumber)during four-point loading tests were compared.The AE activities caused by loadings were investigated through the single parameter analysis and K-means cluster analysis.Results showed that the bending strength of bamboo scrimber was 3.6 times that of bam-boo plywood and 2.7 times that of SPF dimension lumber,respectively.Due to the high strength and toughness of bamboo,the AE signals of the two bamboo products were more abundant than those of SPF dimension lumber.However,the AE evolution trend of the three materials was similar,which all experienced three stages,including gentle period,steady period and steep period,and the area of rupture precursor characteristics could be recognized before the specimen destroyed.Due to the bottom layer was first tensile failure,the main structure of bamboo plywood was destroyed after the stress redistribution.The rupture precursor characteristics could be observed before each peak.Findings put in evidence a good correlation between AE clusters of two bamboo products,while the amplitude and energy of wood signals were lower than those of bamboo.The amplitude and energy from the propagation and aggregation of cracks were greater than those related to micro-cracks initiation.
基金supported by National Key R&D Program of China[grant number 2017YFC0703502]the National Natural Science Foundation of China(NSFC)[grant numbers 51978345,51678310 and 51708304]K.C.Wong Magna Fund at the Ningbo University.
文摘The steel-bamboo composite structure is a newly developed structure,combining phyllostachys pubescens(also called Moso bamboo)plywood and cold-formed thin-walled steel with structural adhesive.The reliability of steelbamboo interface is the premise of composite effect.13 specimens were prepared to investigate the failure modes and mechanism of the steel-bamboo interface on the basis of push-out test,and the strain difference analysis method was proposed to study the distribution of shear stress.The results show that the main failure modes of steel-bamboo interface are adhesion failure and splitting of bamboo plywood.The shear stress is not evenly distributed along the longitudinal direction of the interface,showing a shape of“larger at two ends and smaller in the middle”.The lower end of the interface is the initial location of the interface failure and the shear stress concentration degree is positively correlated with the thickness of the externally bonded bamboo plate.The shear resistance of steel-bamboo interface can be enhanced by improving the adhesion between steel and structural adhesive and ameliorating the quality of bamboo products.
