Vision sensing of P-GMAW weld pool using narrow band filters with different center wavelengths

The selection of narrow band filter＇s center wavelength has an important influence on the quality of the weld pool image captured in passive vision mettmd for controlling arc welding process. In this paper, 29 narrow band filters with different center wavelengths ranging from ultraviolet to near infrared wavelength were used to capture images of weld pool during both the peak current period and the base current period of P-GMA W （ pulsed gas metal arc welding）. The experimental results showed that the filters with near infrared center wavelength could weaken the arc most during the peak current period, while during the base current period the entire weld pool could be seen with the filters with wavelength above 600 nm. The camera spectral response and the radio of arc to weld pool emission were considered to analyze the phenomenon of experimental results.

Narrow-band high-transmittance birefringent filter and its application in wide color gamut display

We propose a narrow-band birefringent filter and its application in wide color gamut.The birefringent filter consists of five phase retarders and two polarizers,and it has both narrow band and high transmittance.In the experiment,we fabricate the birefringent filter using quartz phase retarders and polarizers,and apply it in serval different displays.The color gamuts of displays are enhanced more than 30%NTSC(National Television System Committee),and the widest color gamuts that have been obtained are 126%NTSC in liquid crystal displays and 138%NTSC in organic light-emitting devices.Moreover,the deep blue light in spectrum of display can be reduced using the birefringent filter.The birefringent filter can be an efficient element to achieve wide color gamut display.

CFOA Based Band Pass and Band Stop Ladder Filter—A New Configuration

A new technique for the conversion of ladder based filter into CFOA based filter has been proposed. The technique uses signal flow graph and converts the existing LC ladder based filter into band pass & band stop configurations. The design of band pass and band stop filter has been realized using the proposed technique. The proposed configuration is implemented using CFOA as an active device and all the capacitors are grounded. CFOA based circuits have greater linearity, high dynamic rate, high slew rate and high signal bandwidth. Simulation has been carried out using simulation software P Spice (v10.1). The simulation results have been demonstrated and discussed.

Universal Band Pass Sampling Algorithm for Integration of Multiple Wireless Technologies Using Software Defined Radio Platform

Software Defined Radio (SDR) architecture allows us to integrate different mobile technologies using common hardware but with different software modules. To achieve this, we need to keep the signal in digital form for as much portion of the circuitry as possible, so that the implementation could be carried out by programmable digital processors. For this purpose, the incoming radio frequency (RF) signal is down converted to baseband spectrum using band pass sampling method. Research works carried out so far in this field have developed a few algorithms for band pass sampling. But, these algorithms are not much useful for most of the mobile communication systems and they use complex methodology for computing the sampling frequency values. In order to use the SDR platform to integrate all current wireless technologies, an efficient, cost effective and less complex algorithm that can be labelled as universal band pass sampling algorithm is developed in this paper for multiple mobile systems. This algorithm is based on a novel idea of inserting guard bands between the signals which reduces the design complexities of perfect ADC and sharp cut off filters. Using this algorithm, valid sampling frequency ranges and corresponding IF values are calculated for down converting RF signals. The algorithm is tested for six RF signals of different wireless technologies which are integrated and simultaneously down converted using SDR based front end receiver and thus the system multiplies the base station capacity by a factor of six. The simulation results are obtained and shown in this paper which proves that the algorithm developed works well for most of the wireless technologies.

Characterization of Simulator and Relative Spectral Responsivity Measurements of Photovoltaic Modules with Band Pass Filter Technique

One of the most important parameter used for the evaluation of the energy rating of PV modules is, their spectral responsivities which are the measure of electrical performance parameters per incident solar radiation. In this work, spectral responsivity measurements of a mono-crystalline, a poly-crystalline, a CIGS thin film and a bifacial module were measured using xenon-based flash type solar simulator system and a set of band pass filters. For the comprehensive characterization of parameters that may influence the spectral responsivity measurements, initially the simulator system was characterized both optically and thermally according to the IEC60904-9 and IEC60891 standard requirements. The optical characterizations in terms of spectral match, spatial non-uniformity and temporal instability indicate that the measured results (~3.0%, ~0.30% and ~0.20%) according to the IEC 60904-9 standard’s classification requirements correspond to A+A+A+ classes. Moreover, thermal characterizations in terms of the temperature uniformity show that over the 2 × 2 m area temperature uniformity of simulator system’s light distribution (1ºC) is almost two times better than the IEC 60891 standard requirements (±2ºC). Next, PV modules were electrically stabilized according to the IEC 61215-2 standard requirement’s (stability test) to reduce the fluctuations in their electrical performance parameters. Then, using the band pass filters, temperature controlled xenon-based solar simulator system and a reference PV module of the spectral responsivity of PV modules were measured from 400 nm to 1100 nm with 50 nm steps with relative uncertainty of 10-3 level.

Performanceanalysisofalowpowerlownoisetunablebandpassfilterformultiband RF front end

This paper presents a low power tunable active inductor and RF band pass filter suitable for multiband RF front end circuits. The active inductor circuit uses the PMOS cascode structure as the negative transconductor of a gyrator to reduce the noise voltage. Also, this structure provides possible negative resistance to reduce the inductor loss with wide inductive bandwidth and high resonance frequency. The RF band pass filter is realized using the proposed active inductor with suitable input and output buffer stages. The tuning of the center frequency for multiband operation is achieved through the controllable current source. The designed active inductor and RF band pass filter are simulated in 180 nm and 45 nm CMOS process using the Synopsys HSPICE simulation tool and their performances are compared. The parameters, such as resonance frequency, tuning capability, noise and power dissipation, are analyzed for these CMOS technologies and discussed. The design of a third order band pass filter using an active inductor is also presented.