The thermo-mechanical stress and deformation of water-cooled gun barrel during burst firing are studied by finite element analysis (FEA). The problem is modeled in two steps: 1) A transient heat transfer analysis is f...The thermo-mechanical stress and deformation of water-cooled gun barrel during burst firing are studied by finite element analysis (FEA). The problem is modeled in two steps: 1) A transient heat transfer analysis is first carried out in order to determine temperature evolution and to predict the residual temperatures during the burst firing event; 2) The thermo-mecha- nical stresses and deformation caused by both the residual temperature field and the gas pressure are then calculated. The results show that the residual temperature field tends to a steady state with the increasing of rounds. The residual temperature field has much effect on the gun barrel stress and deformation, especially on the assembly area between barrel and water jacket. The gage between the barrel and water jacket is the critical factor to the thermo- mechanical stress and deformation. The results of this analysis will be very useful to develop the new strength design theory of the liquid-cooled gun barrel.展开更多
This study reports the development and performance of a pilot-scale barrel atmospheric plasma reactor for the atmospheric plasma activation treatment of polymer particles. The polymer particles treated included acrylo...This study reports the development and performance of a pilot-scale barrel atmospheric plasma reactor for the atmospheric plasma activation treatment of polymer particles. The polymer particles treated included acrylonitrile butadiene styrene(ABS) and polypropylene(PP). These particles had diameters in the range of 3–5 mm. The initial studies were carried out using a laboratory-scale barrel reactor designed to treat polymer particle batch sizes of 20 g. A pilot-scale reactor that could treat 500 g particle batch sizes was then developed to facilitate pre-industrial-scale treatments. The effect of operating pulse density modulation(PDM) in the range 10%–100% and plasma treatment time on the level of activation of the treated polymers were then investigated. ABS revealed a larger decrease in water contact angle compared with PP after plasma treatment under the same conditions. The optimal treatment time of ABS(400 g of polymer particles) in the pilot-scale reactor was 15 min. The plasma-activated polymer particles were used to fabricate dog-bone polymer parts through injection molding.Mechanical testing of the resulting dog-bone polymer parts revealed a 10.5% increase in tensile strength compared with those fabricated using non-activated polymer particles.展开更多
文摘The thermo-mechanical stress and deformation of water-cooled gun barrel during burst firing are studied by finite element analysis (FEA). The problem is modeled in two steps: 1) A transient heat transfer analysis is first carried out in order to determine temperature evolution and to predict the residual temperatures during the burst firing event; 2) The thermo-mecha- nical stresses and deformation caused by both the residual temperature field and the gas pressure are then calculated. The results show that the residual temperature field tends to a steady state with the increasing of rounds. The residual temperature field has much effect on the gun barrel stress and deformation, especially on the assembly area between barrel and water jacket. The gage between the barrel and water jacket is the critical factor to the thermo- mechanical stress and deformation. The results of this analysis will be very useful to develop the new strength design theory of the liquid-cooled gun barrel.
基金support of the Enterprise Ireland Innovation Partnership programthe SFI funded Ⅰ-Form Advanced Manufacturing Research Centre 16/RC/3872
文摘This study reports the development and performance of a pilot-scale barrel atmospheric plasma reactor for the atmospheric plasma activation treatment of polymer particles. The polymer particles treated included acrylonitrile butadiene styrene(ABS) and polypropylene(PP). These particles had diameters in the range of 3–5 mm. The initial studies were carried out using a laboratory-scale barrel reactor designed to treat polymer particle batch sizes of 20 g. A pilot-scale reactor that could treat 500 g particle batch sizes was then developed to facilitate pre-industrial-scale treatments. The effect of operating pulse density modulation(PDM) in the range 10%–100% and plasma treatment time on the level of activation of the treated polymers were then investigated. ABS revealed a larger decrease in water contact angle compared with PP after plasma treatment under the same conditions. The optimal treatment time of ABS(400 g of polymer particles) in the pilot-scale reactor was 15 min. The plasma-activated polymer particles were used to fabricate dog-bone polymer parts through injection molding.Mechanical testing of the resulting dog-bone polymer parts revealed a 10.5% increase in tensile strength compared with those fabricated using non-activated polymer particles.
