Design and performance study of a dielectric-filled cavity beam current monitor for HUST-PTF

To guarantee the exact proton dose applied to patients and ensure treatment safety while disrupting and destroying tumor cells,it is essential to accurately monitor the proton beam current in real time during patient treatment.Because clinical treatment requires a proton beam current in the∼nA range,nondestructive beam current monitors(BCMs)are preferred to minimize the degradation of beam quality.However,this poses significant challenges in accurately monitoring such extremely low beam intensities.This study proposes a cavity-type BCM equipped with a dielectric plate to reduce its dimensions and achieve sufficient measurement sensitivity for practical requirements.A prototype cavity BCM was fabricated,and off-line testing was performed using a metal wire to simulate the beam to study its performance.Both the simulation and experi-mental results showed that the cavity BCM could measure ultralow proton beam currents with a resolution up to 0.03 nA.

An active-passive beam current transformer

In this article,a new type current transformer was developed using an active-passive circuit to improve low frequency response of the system without impairing high frequency response.The active-passive current transformer with In-flange was fabricated.Theoretical analysis,numerical simulations and experimental results are given.

Influence of the cathode position on beam current characteristics in the thermionic electron gun

Purpose The research focuses on the simulation of influence of cathode positions on beam current characteristics in the thermionic electron gun.Methods The electricfield distribution,bias voltage range and electron beam quality under different cathode positions were simulated by CST software.Results Changes in the cathode position can cause changes in the electricfield distributions under the cathode emission surface change,thereby changing the size of the effective emitting area and affecting the relationship between the bias voltage and beam current.Conclusions Only when the cathode is installed in the proper positions,the beam current and the bias voltage have an approximately linear proportional relationship.When the cathode is installed improperly,the electron beam emission is disordered,resulting in decreased electron beam quality.

Development of new beam current transformer based on TMR

Purpose and background As the magneto-resistor technology is developed,applying it to beam instrumentation for the accelerator becomes possible.In this paper,a new principle beam current sensor based on TMR linear sensor is introduced.Methods Feasibility research by simulation and calculation has been done,a study of the critical component for the whole system has been carried out,and all these are presented in this paper.Results and conclusions Laboratory test results include the nonlinear error,and resolution analysis is introduced.Specific work plan for the next step of the improvement and upgrade is also referred to.

Effect of Beam Current and Diameter on Electron Probe Microanalysis of Carbonate Minerals

The effect of operating conditions on the time-dependent X-ray intensity variation is of great importance for the optimal EPMA conditions for accurate determinations of various elements in carbonate minerals. Beam diameters of 0, 1, 2, 5, 10, 15, and 20 μm, and beam currents of 3, 5, 10, 20,and 50 nA were tested. Ca, Mg, Zn, and Sr were found to be more sensitive to electron beam irradiation as compared to other elements, and small currents and large beam diameters minimized the timedependent X-ray intensity variations. We determined the optimal EPMA operating conditions for elements in carbonate: 10 μm and 5 nA for calcite;10 μm and 10 nA for dolomite;5 μm and 10 nA or 10 μm and 20 nA for strontianite;and 20 nA and 5 μm for other carbonate. Elements sensitive to electron beam irradiation should be determined first. In addition, silicate minerals are preferred as standards rather than carbonate minerals.

Compounded Surface Modification of ZK60 Mg Alloy by High Current Pulsed Electron Beam+Micro-plasma Oxidation

In this study, compounded surface modification technology-high current pulsed electron beam （HCPEB） ＋ micro-plasma oxidation （MPO） was applied to treat ZK60 Mg alloys. The characteristics of the microstructure of ZK60 Mg alloy after single MPO and HCPEB＋MPO compounded treatment were investigated by SEM. The results showed that the density of the ceramic layer of HCPEB＋MPO-treated ZK60 Mg alloy was improved and defects were reduced compared to that under MPO treatment alone. Surface modified layer of ZK60 Mg alloys treated by HCPEB＋MPO was divided into three zones, namely the top loose ceramic zone, middle compact zone and inside HCPEB-induced melted zone. Corrosion resistance of ZK60 Mg alloy before and after the compounded surface modification was measured in a solution of 3.5% NaCl by potentiodynamic polarization curves. It was found that the corrosion current density of ZK60 Mg alloys could be reduced by about three orders of magnitude, from 311μA/cm^2 of the original sample to 0.2μA/cm^2 of the HCPEB＋MPO-treated sample. This indicates the great application potential of the HCPEB＋MPO compounded surface modification technology in improving the corrosion resistance of ZK60 Mg alloys in the future.

The Arc Regulation Characteristics of the High-Current Ion Source for the EAST Neutral Beam Injector

The arc regulation method is applied to the high-current ion source for high-power hydrogen ion beam extraction for the first time. The characteristics of the arc and beam, including the probe ion saturation current, the arc power and the beam current, are studied with feedback control. The results show that the arc regulation method can be successfully applied to ion beam extraction. This lays a sound foundation for the testing of a new ion source and the operation of a conditioned ion source for neutral beam injector devices.

Improvement of Wear Resistance of Magnesium Alloy AZ91HP by High Current Pulsed Electron Beam Treatment

Surface modification of magnesium alloy AZ91HP (9wt%Al, 0.5wt%Zn, 0.5wt%Mn, Mg remaining percentage) by high current pulsed electron beam (HCPEB) treatment was studied in this paper. The secondary phase MgnAln is nearly completely dissolved and as a result, a super-saturated solid solution forms on the re-melted surface. The microhardness is increased both in and far beyond the heat-affected zone (HAZ), reaching about 250um. Measurements on sliding wear have shown that the wear resistance of the treated samples was improved by a factor of about 2.4 as compared to the as-received sample. It is also found that the sliding wear resistance can be further improved by surface alloying with TiN.

Improvement of wear resistance of AZ31 and AZ91HP by high current pulsed electron beam treatment

The surface modification of magnesium alloys (AZ31 and AZ91HP) was studied by a high current pulsed electron beam(HCPEB). The results show that the cross-sectional microhardness of treated samples increases not only in the heat affected zone(HAZ), but also beyond HAZ, reaching over 250μm. This is due to the action of quasi-static thermal stress and the shock thermal stress wave with materials, which result in its fast deformation on the surface layer and so increases microhardness. For the AZ91HP alloy, a nearly complete dissolution of the intermetallic phase Mg_ 17Al_ 12 is observed, and a super-saturated solid solution forms on the re-melted surface, which is due to the solute trapping effect during the fast solidification process. Measurements on sliding wear show that wear resistance is improved by approximately 5.6 and 2.4 times for the AZ31 and AZ91HP respectively, as compared with as-received samples.

Characterizing modified surface layer of 316L stainless steel treated by high current pulsed electron beam

High current pulsed electron beam(HCPEB) is now developing as a useful tool for surface modification of materials.When concentrated electron flux transferring its energy into the surface layer of target material within a short pulse time,coupled thermal and stress processes would lead to the formation of metastalbe microstructure with improved properties.In the present work,HCPEB treatment of 316L stainless steel(SS) was carried out and the microstructural changes in modified surface layer were characterized with optical microscopy,X-ray diffractometry and electron backscatter diffractometry(EBSD) techniques.The corrosion resistance of modified surface was measured in a 5wt.% salt solution.The evolution regularity of surface craters and grain refinement effect,as well as the preferred orientation of(111) crystal plane occurring in the HCPEB treatment under different working parameters were discussed along with their influence on corrosion resistance.

Microstructure and properties of Nb/Ta multilayer films irradiated by a high current pulse electron beam

Nb/Ta multilayer films deposited on Ti6A14V substrate with Nb and Ta monolayer thicknesses of 30 nm, 120 nm, and 240 nm were irradiated by a high current pulse electron beam （HCPEB） to prepare Nb-Ta alloyed layers. The mi- crostructure and the composition of the outmost surface of melted alloyed layers were investigated using a transmission electron microscope （TEM） equipped with an X-ray energy dispersive spectrometer （EDS） attachment. The Ta content of the alloyed surface layer prepared from the monolayer of thickness 30 nm, 120 nm, and 240 nm was- 27.7 at.%, 6.37 at.%, and 0 at.%, respectively. It was found that the Ta content in the alloyed layer plays a dominant role in the microstructure of the films. The hardness and the wear rate of the alloyed layers decrease with the increasing content of Ta in the surface laver.

Development of data acquisition and over-current protection systems for a suppressor-grid current with a neutral-beam ion source

Neutral beam injection is one of the effective auxiliary heating methods in magnetic-confinementfusion experiments. In order to acquire the suppressor-grid current signal and avoid the grid being damaged by overheating, a data acquisition and over-current protection system based on the PXI（PCI e Xtensions for Instrumentation） platform has been developed. The system consists of a current sensor, data acquisition module and over-current protection module. In the data acquisition module,the acquired data of one shot will be transferred in isolation and saved in a data-storage server in a txt file. It can also be recalled using NBWave for future analysis. The over-current protection module contains two modes： remote and local. This gives it the function of setting a threshold voltage remotely and locally, and the forbidden time of over-current protection also can be set by a host PC in remote mode. Experimental results demonstrate that the data acquisition and overcurrent protection system has the advantages of setting forbidden time and isolation transmission.

Effect of longitudinal applied magnetic field on the self-pinched critical current in intense electron beam diode

The effect of applied longitudinal magnetic field on the self-pinched critical current in the intense electron beam diode is discussed. The self-pinched critical current is derived and its validity is tested by numerical simulations. The results shows that an applied longitudinal magnetic field tends to increase the self-pinched critical current. Without the effect of anode plasma, the maximal diode current approximately equals the self-pinched critical current with the longitudinal magnetic field applied; when self-pinched occurs, the diode current approaches the self-pinched critical current.

HIGH-CURRENT PULSED ELECTRON BEAM: RAPID SURFACE ALLOYING AND WEAR RESISTANCE IMPROVEMENT

The present paper reports the rapid surface alloying induced by the bombardment of high-current pulsed electron beam. Two kinds of substrate materials were examined to show this effect. The first sample was a pure Al metal pre-coated with fine carbon powders prior to the bombardment, and the second alloy is the D2-Crl2MolVl mould steel pre-coated with Cr, Ti, and TiN powders. The surface elements diffuse about several micrometers into the substrate materials only after several bombardments. Tribological behaviors of these samples were characterized and significant improvement in wear resistance was found. Finally, a TEM analysis reveals the presence of stress waves generated by coupled thermal and stress fields, which was considered as the main cause of the enhanced properties.

Space-charge limiting currents for magnetically focused intense relativistic electron beams

The self-consistent differential equations, which describe a laminar-flow equilibrium state in a magnetically focused intense relativistic electron beam propagating inside a conducting waveguide, are presented. The canonical angular momentum, Pe, defined under the conditions at the source, uniquely determines the possible solutions of these equations. By numerically solving these equations, the space-charge limited current and the externally applied magnetic field are obtained in a solid beam and a hollow beam in two cases of Pθ= 0 （magnetically shielded source） and Pθ= const. （immersed source） separately. It is shown that the hollow beam is more beneficial to the propagation of the intense relativistic beam through a drift tube than the solid beam.

Current transport in ZnO/Si heterostructure grown by laser molecular beam epitaxy

The n-ZnO/p-Si heterojunction was fabricated by depositing high quality single crystalline aluminium-doped n-type ZnO film on p-type Si using the laser molecular beam epitaxy technique. The heterojunction exhibited a good rectifying behavior. The electrical properties of the heterojunction were investigated by means of temperature dependence current density-voltage measurements. The mechanism of the current transport was proposed based on the band structure of the heterojunction. When the applied bias V is lower than 0.15 V, the current follows the Ohmic behavior. When 0.15 V ~ V 〈 0.6 V, the transport property is dominated by diffusion or recombination in the junction space charge region, while at higher voltages （V 〉 0.6 V）, the space charge limited effect becomes the main transport mechanism. The current-voltage characteristic under illumination was also investigated. The photovoltage and the short circuit current density of the heterojunction aproached 270 mV and 2.10 mA/cm^2, respectively.

Numerical simulation of thermal-mechanical process of Al-Si-Pb alloy treated by high current pulsed electron beam

The modified microstructure of Al-Si-Pb alloys irradiated by high current electron beam (HCPEB) reveals three distinct regions: a molten zone, an overlapped zone of heat-affected and quasistatic thermal stress-affected zone, and a transition zone followed by the substrate. The hardness and wear properties of the alloys were significantly improved. To better understand these changes in microstructure and properties, the physical model for the simulation of temperature and quasistatic stress fields was established. Based on experimental investigation and physical models, the temperature field and stress field were simulated for Al-Si-Pb alloy. The starting melting position, largest crater depth, melting layer thickness, and quasistatic stress distribution were obtained. These results reveal the mechanism of crater formation on the surface and improvement of hardness and wear resistance.

高能束表面改性技术在航空领域的应用

高能束表面改性适用于各种金属和合金,能够显著提升材料表面硬度、耐磨、耐蚀等性能指标,是航空部件实现性能提升的有效手段之一。本文总结了6种高能束表面改性技术的基本原理、设备构成和改性应用,其中激光相变硬化通过马氏体相变强化金属材料表面;激光熔覆通过选择不同粉末实现表面修复和表面性能提升,重点在于控制裂纹缺陷;激光冲击强化可有效解决航空发动机部件高周疲劳断裂问题;强流脉冲电子束和强流脉冲离子束一方面需要提高设备的性能和运行稳定性,另一方面要针对航空部件应用开展深入研究;而离子束辅助沉积则可以通过制备固体润滑涂层实现对微动磨损的有效防护。最后,提出对高能束表面改性机理深入研究、发展专业化智能化装备和实现多种束源复合与集成的发展方向。

一种小尺寸轫致辐射转换靶设计

以减小直线感应加速器X射线光源横向尺寸为目标,开展轫致辐射转换靶的设计。对聚焦打靶过程中电子束运动轨迹进行分析,指出同一个电子束轨迹分布,既可以描述为电子束在某纵向位置处具有一定的横向展宽,也可以描述为电子束保持较小横向尺寸时的轴向分布展宽,由此提出在束腰附近放置多个小靶片实现聚焦电子束有效阻挡的小尺寸多层靶概念设计。采用EGS4程序对X射线产额进行计算,发现靶厚度在一定范围内改变时X射线产额变化较小,基于这一规律完成了小尺寸多层靶的结构设计。进一步考察了一个设计应用实例,当聚焦电子束最小包络直径3 mm、会聚角100 mrad时,对比大尺寸靶,采用小尺寸多层靶可以获得等效直径减小约50%、产额减小约10%的X射线光源。该设计方法有望在相同的电子束品质和聚焦条件下,获得横向尺寸小于电子束最小束包络直径的X射线光源,具有一定的应用价值。

离子电喷雾推力器束电流数学模型与敏感性分析

虽然阵列式结构的离子电喷雾推力器具有小体积、高比冲、高推力分辨率等优点,但是其发展受到了缺乏理论研究的限制。针对该问题,基于多点发射现象发展了描述推力器束电流的数学模型,并通过智能优化算法对模型中的经验系数进行了辨识,研究了高、低电压下束电流及发射行为存在的不同特征。基于Sobol方法进行了全局敏感性分析,研究了发射体结构的几何参数对束电流的影响程度。模型计算结果与试验结果基本一致,当电压大于1.5 kV时,发射点基底半径与多孔储层孔隙半径相当,外加电场主要影响束电流的非线性增加;电压小于1.5 kV时,发射点数量较少,基底半径是多孔储层孔隙半径的1.5倍,发射点数量是影响束电流大小的关键因素。敏感性分析结果表明,发射体尖端与提取极之间的距离对束电流的影响程度最大,其1阶敏感性指数为0.841,在加工制造中须严格控制其公差大小。