Simulation and Optimization of Energy Efficiency and Total Enthalpy Analysis of Sand Based Packed Bed Solar Thermal Energy Storage

This study is focused on the simulation and optimization of packed-bed solar thermal energy storage by using sand as a storage material and hot-water is used as a heat transfer fluid and storage as well.The analysis has been done by using the COMSOL multi-physics software and used to compute an optimization charging time of the storage.Parameters that control this optimization are storage height,storage diameter,heat transfer fluid flow rate,and sand bed particle size.The result of COMSOL multi-physics optimized thermal storage has been validated with Taguchi method.Accordingly,the optimized parameters of storage are:storage height of 1.4m,storage diameter of 0.4 m,flow rate of 0.02 kg/s,and sand particle size 12 mm.Among these parameters,the storage diameter result is the highest influenced optimized parameter of the thermal storage fromthe ANOVA analysis.For nominal packed bed thermal storage,the charging time needed to attain about 520 K temperature is more than 3500 s,while it needs only about 2000 s for the optimized storage which is very significant difference.Average charging energy efficiency of the optimized is greater than the nominal and previous concrete-based storage by 13.7%,and 13.1%,respectively in the charging time of 2700 s.

Effect of Radial Porosity Oscillation on the Thermal Performance of Packed Bed Latent Heat Storage

Owing to its high heat storage capacity and fast heat transfer rate,packed bed latent heat storage(LHS)is considered as a promising method to store thermal energy.In a packed bed,the wall effect can impact the packing arrangement of phase change material(PCM)capsules,inducing radial porosity oscillation.In this study,an actual-arrangement-based three-dimensional packed bed LHS model was built to consider the radial porosity oscillation.Its fluid flow and heat transfer were analyzed.With different cylindrical sub-surfaces intercepted along the radial direction in the packed bed,the corresponding relationships between the arrangement of capsules and porosity oscillation were identified.The oscillating distribution of radial porosity led to a non-uniform distribution of heat transfer fluid(HTF)velocity.As a result,radial temperature distributions and liquid fraction distributions of PCMs were further affected.The effects of different dimensionless parameters(e.g.,tube-to-capsule diameter ratio,Reynolds number,and Stefan number)on the radial characteristics of HTF and PCMs were discussed.The results showed that different diameter ratios correspond to different radial porosity distributions.Further,with an increase in diameter ratio,HTF velocity varies significantly in the near wall region while the non-uniformity of HTF velocity in the center region will decrease.The Reynolds and Stefan numbers slightly impact the relative velocity distribution of the HTF-while higher Reynolds numbers can lead to a proportional improvement of velocity,an increase in Stefan number can promote heat storage of the packed bed LHS system.

CO_2 –H_2O–coal interaction of CO_2 storage in coal beds

In order to study the physical and chemical reaction after CO2 injected into coal beds at different condition.The physical and chemistry reaction among CO2,H2O and coal was studied,and the influence on permeability and porosity of coal beds was carried out.The experimental method was used,so did the basic theory of mineralogy,coal petrology,geochemistry,analytical geochemistry and physical chemistry.In this experiment,the changes of mineral and permeability of coal and water quality were observed through CO2 solution reacting with different coal samples.The differences could be found out by comparing the properties and microcrystalline structure before and after the reaction.There are three results were carried out:First,the content of carbonate in coal beds decreases because of the dissolution reaction between carbonate minerals and CO2 solution,and precipitation is formed by reaction of chlorite and orthoclase.Second,the result that permeability and porosity of coal beds are improved after the reaction is proposed.Third,the initial permeability of different coal samples plays a great role on the reaction,and the improvement of permeability is not obvious in the samples which have too low or too high permeability,and the improvement is good in medium permeability(0.2–3 mD).

Parametric analysis of a packed bed thermal storage device with phase change material capsules in a solar heating system application

The goal of this study is to investigate the effect of key design parameters on the thermal performance of the packed bed heat storage device by numerical calculation.A one-dimensional,non-equilibrium packed bed latent heat storage mathematical model was established and the applicability of the model was verified.The results demonstrate that the inlet temperature of the heat transfer fluid(HTF)had the greatest influence on each index.When the inlet temperature increased from 333 K to 363 K,exergy destruction increased threefold,effective heat storage time decreased by 67%,effective heat storage increased by 38%,and exergy efficiency decreased by 11%.The decrease of the capsule diameter had a positive effect on each evaluation index.According to the sensitivity analysis,the order of importance of each parameter within their variation range was HTF inlet temperature,HTF flow rate,PCM capsule size and PCM initial temperature.