Quasimolecular Dynamic Simulation for Bending Fracture of Laminar Composite Materials

Recently, quasimolecular dynamics has been successfully used to simulate the deformation characteristics of actual size solid materials. In quasimolecular dynamics, which is an attempt to bridge the gap between atomistic and continuum simulations, molecules are aggregated into large units, called quasimolecules, to evaluate large scale material behavior. In this paper, a 2-dimensional numerical simulation using quasimolecular dynamics was performed to investigate laminar composite material fractures and crack propagation behavior in the uniform bending of laminar composite materials. It was verified that under bending deformation laminar composite materials deform quite differently from homogeneous materials

Bending strength degradation of a cantilever plate with surface energy due to partial debonding at the clamped boundary

This paper investigates the bending fracture problem of a micro/nanoscale cantilever thin plate with surface energy,where the clamped boundary is partially debonded along the thickness direction.Some fundamental mechanical equations for the bending problem of micro/nanoscale plates are given by the Kirchhoff theory of thin plates,incorporating the Gurtin-Murdoch surface elasticity theory.For two typical cases of constant bending moment and uniform shear force in the debonded segment,the associated problems are reduced to two mixed boundary value problems.By solving the resulting mixed boundary value problems using the Fourier integral transform,a new type of singular integral equation with two Cauchy kernels is obtained for each case,and the exact solutions in terms of the fundamental functions are determined using the PoincareBertrand formula.Asymptotic elastic fields near the debonded tips including the bending moment,effective shear force,and bulk stress components exhibit the oscillatory singularity.The dependence relations among the singular fields,the material constants,and the plate's thickness are analyzed for partially debonded cantilever micro-plates.If surface energy is neglected,these results reduce the bending fracture of a macroscale partially debonded cantilever plate,which has not been previously reported.

A New Method for Determining J_(IC) of High StrengthHigh Fracture Toughness Steels by SingleThree Point Bend Specimen

A single three point bend specimen compliance method for determining JIC of high strength high fracture toughness steels is presented and a formula for calculatinff J-integral is proposed as follows.It is simple and valid for high strength high fracture toughness steels. The values of JIC and KIC measured by this method are in good agreement with those measured by standard test method.

Heterogeneous Fracture Simulation of Three-point Bending Plain-concrete Beam with Double Notches

Plain concrete is regarded as a two-phase material comprising randomly distributed aggregates and mortar matrix. A series of three-point bending concrete beams with symmetric or asymmetric double notches are modeled using the modified random aggregate generation and packing algorithm. The cohesive zone model is used as the fracture criterion and the cohesive el- ements are inserted into both the mortar matrix and the aggregate-mortar interfaces as potential micro-cracking zones. The dead and alive crack phenomena are studied experimentally and nu- merically; and the influences of notch location, aggregate distribution and gradation on fracture are numerically evaluated. Some important conclusions are given.

In situ synthesis and phase analysis of low density O'-sialon-based multiphase ceramics

In situ formed low density O＇-sialon-based multiphase ceramics were prepared by liquid-phase sintering method at 1400°C with Si3N4, SiO2 and Al2O3 as raw materials.Crystalline phases were identified by X-ray diffraction（XRD）.The quantitative phase analysis was finished by matrix-flushing method and the substitution parameter x value of O＇-sialon was estimated.The effects of sintering additives on the phase composition of the material were studied.The results show that, when using Y2O3 alone, Al6Si2O13 phase can be formed in the material, but when using Y2O3 and MgO, MgAl2O4 phase can be preferentially formed and the Al6Si2O13 is not observed.The mechanical properties of the material were measured and the relationships between microstructure and mechanical properties were discussed.The sample with Y2O3 and MgO sintering additives, using fused quartz alone as SiO2 source, displays a combination of high bending strength（163 MPa） and good fracture toughness（3.11 MPa·m1/2）.Bending strength and fracture toughness of the samples increase with the increase of the content and aspect ratio of elongated grains and decrease with the increase of the porosity.

Nano-refinement of the face-centered cubic Zr(Fe,Cr)_(2)secondary phase particles in Zircaloy-4 alloy via localized-shearing/bending-driven fracture under high-temperature compression

Nanoparticles are extensively introduced to improve the mechanical,physical,and chemical properties of alloys.In the present study,the underlying nano-refinement mechanisms of face-centered cubic Zr(Fe,Cr)_(2)secondary phase particles(SPPs)that precipitated in Zircaloy-4 alloy under high-temperature compression were investigated in detail by utilizing high-resolution transmission electron microscopy(HRTEM)and conventional TEM techniques.The frequently observed Zr(Fe,Cr)_(2)SPPs were incoherent with the matrix and exhibited brittle fracture behaviors without measurable plasticity.HRTEM observations revealed two mechanisms underlying the nano-refinement of incoherent micro-sized SPPs via localized shear fracture on{11¯2}SPP and nanoprecipitate-assisted bending fracture,respectively.The latter was,for the first time,found to occur when the movements of large SPPs were blocked by nanometer-sized SPP during alloy deformation.Accordingly,two force models were proposed to visualize their potential nano-refinement processes.The knowledge attained from this study sheds new light on the deformation behaviors of Zr(Fe,Cr)_(2)SPPs and their associated size refinement mechanisms under high-temperature compression,and is expected to greatly benefit the process optimization of zirconium alloys to achieve precipitate nano-refinement.

Mechanical Properties and Fracture Behavior of Mg-Al/AlN Composites with Different Particle Contents

In this study, magnesium matrix composites reinforced with different loading of AlN particles were fabricated by the powder metallurgy technique. The microstructure, bending strength and fracture behavior of the resulting Mg-Al/Al N composites were investigated. It showed that the 5 wt% AlN reinforcements led to the highest densification and bending strength. The total strengthening effect of AlN particles was predicted by considering the contributions of CTE mismatch between the matrix and the particles,load bearing and Hall-Petch mechanism. The results revealed that the increase of dislocation density,the change of Mg17Al12 phase morphology, and the effective load transfer were the major strengthening contributors to the composites. The fracture of the composites altered from plastic to brittle mode with increasing reinforcement content. The regions of clustered particles in the composites were easy to be damaged under external load, and the fracture occurred mainly along grain boundaries.