Local leakage current behaviours of BiFeO_3 films

The leakage current behaviours of polycrystalline BiFeO3 thin films are investigated by using both conductive atomic force microscopy and current-voltage characteristic measurements. The local charge transport pathways are found to be located mainly at the grain boundaries of the films. The leakage current density can be tuned by changing the post-annealing temperature, the annealing time, the bias voltage and the light illumination, which can be used to improve the performances of the ferroelectric devices based on the BiFeOa films. A possible leakage mechanism is proposed to interpret the charge transports in the polycrystalline BiFeO3 films.

Structure,ferroelectric,and enhanced fatigue properties of sol–gel-processed new Bi-based perovskite thin films of Bi(Cu_(1/2)Ti_(1/2))O_(3)–PbTiO_(3)

Bi-based perovskite ferroelectric thin films have wide applications in electronic devices due to their excellent ferroelectric properties.New Bi-based perovskite thin films Bi(Cu_(1/2)Ti_(1/2))O_(3)–PbTiO_(3)(BCT–PT) are deposited on Pt(111)/Ti/SiO_(2)/Si substrates in the present study by the traditional sol–gel method.Their structures and related ferroelectric and fatigue characteristics are studied in-depth.The BCT–PT thin films exhibit good crystallization within the phase-pure perovskite structure,besides,they have a predominant(100) orientation together with a dense and homogeneous microstructure.The remnant polarization(2P_(r)) values at 30 μC/cm^(2) and 16 μC/cm^(2) are observed in 0.1BCT–0.9PT and 0.2BCT–0.8PT thin films,respectively.More intriguingly,although the polarization values are not so high,0.2BCT–0.8PT thin films show outstanding polarization fatigue properties,with a high switchable polarization of 93.6% of the starting values after 10^(8) cycles,indicating promising applications in ferroelectric memories.

Transfer film effects induced by 3D-printed polyether-ether-ketone with excellent tribological properties for joint prosthesis

Based on the building principle of additive manufacturing,printing orientation mainly determines the tribological properties of joint prostheses.In this study,we created a polyether-ether-ketone(PEEK)joint prosthesis using fused filament fabrication and investigated the effects of printing orientation on its tribological properties using a pin-on-plate tribometer in 25% newborn calf serum.An ultrahigh molecular weight polyethylene transfer film is formed on the surface of PEEK due to the mechanical capture of wear debris by the 3D-printed groove morphology,which is significantly impacted by the printing orientation of PEEK.When the printing orientation was parallel to the sliding direction of friction,the number and size of the transfer film increased due to higher steady stress.This transfer film protected the matrix and reduced the friction coefficient and wear rate of friction pairs by 39.13%and 74.33%,respectively.Furthermore,our findings provide a novel perspective regarding the role of printing orientation in designing knee prostheses,facilitating its practical applications.

Preparation,Characterization and Photothermal Study of PVA/Ti_(2)O_(3) Composite Films

In this work,flexible photothermal PVA/Ti_(2)O_(3) composite films with different amount(0 wt%,5 wt%,10 wt%,15 wt%)of Ti_(2)O_(3) particles modified by steric acid were prepared by a simple solution casting method.The microstructures,XRD patterns,FTIR spectra,UV-Vis-NIR spectra thermo-conductivity,thermo-stability and photothermal effects of these composite films were all characterized.These results indicated that Ti_(2)O_(3) particles were well dispersed throughout the polyvinyl alcohol(PVA)matrix in the PVA/Ti_(2)O_(3) composite films.And Ti_(2)O_(3) particles could also effectively improve the photothermal properties of the composite films which exhibited high light absorption and generated a high temperature(about 57.4℃for film with 15 wt%Ti_(2)O_(3) amount)on the surface when it was irradiated by a simulated sunlight source(1 kW/m^(2)).

Identifying the enhancement mechanism of Al/MoO_(3) reactive multilayered films on the ignition ability of semiconductor bridge using a one-dimensional gas-solid two-phase flow model

Energetic Semiconductor bridge(ESCB)based on reactive multilayered films(RMFs)has a promising application in the miniature and intelligence of initiator and pyrotechnics device.Understanding the ignition enhancement mechanism of RMFs on semiconductor bridge(SCB)during the ignition process is crucial for the engineering and practical application of advanced initiator and pyrotechnics devices.In this study,a one-dimensional(1D)gas-solid two-phase flow ignition model was established to study the ignition process of ESCB to charge particles based on the reactivity of Al/MoO_(3) RMFs.In order to fully consider the coupled exothermic between the RMFs and the SCB plasma during the ignition process,the heat release of chemical reaction in RMFs was used as an internal heat source in this model.It is found that the exothermal reaction in RMFs improved the ignition performance of SCB.In the process of plasma rapid condensation with heat release,the product of RMFs enhanced the heat transfer process between the gas phase and the solid charge particle,which accelerated the expansion of hot plasma,and heated the solid charge particle as well as gas phase region with low temperature.In addition,it made up for pressure loss in the gas phase.During the plasma dissipation process,the exothermal chemical reaction in RMFs acted as the main heating source to heat the charge particle,making the surface temperature of the charge particle,gas pressure,and gas temperature rise continuously.This result may yield significant advantages in providing a universal ignition model for miniaturized ignition devices.

Numerical Analysis on the Effect of n-Si on Cu(In, Ga)Se2 Based Thin-Films for High-Performance Solar Cells by 1D-SCAPS

We report the performances of a chalcopyrite Cu(In, Ga)Se2 CIGS-based thin-film solar cell with a newly employed high conductive n-Si layer. The data analysis was performed with the help of the 1D-Solar Cell Capacitance Simulator (1D-SCAPS) software program. The new device structure is based on the CIGS layer as the absorber layer, n-Si as the high conductive layer, i-In2S3, and i-ZnO as the buffer and window layers, respectively. The optimum CIGS bandgap was determined first and used to simulate and analyze the cell performance throughout the experiment. This analysis revealed that the absorber layer’s optimum bandgap value has to be 1.4 eV to achieve maximum efficiency of 22.57%. Subsequently, output solar cell parameters were analyzed as a function of CIGS layer thickness, defect density, and the operating temperature with an optimized n-Si layer. The newly modeled device has a p-CIGS/n-Si/In2S3/Al-ZnO structure. The main objective was to improve the overall cell performance while optimizing the thickness of absorber layers, defect density, bandgap, and operating temperature with the newly employed optimized n-Si layer. The increase of absorber layer thickness from 0.2 - 2 µm showed an upward trend in the cell’s performance, while the increase of defect density and operating temperature showed a downward trend in solar cell performance. This study illustrates that the proposed cell structure shows higher cell performances and can be fabricated on the lab-scale and industrial levels.

Remarkable Improvement of Ferroelectric Properties and Leakage Current in BiFeO_3 Thin Films by Nd Modification

Ferroelectric and leakage properties are important for ferroelectric applications. Pure and Nd-doped（x=0.05-0.20） BiFeO3 thin films were fabricated by sol-gel method on FTO substrates. The phase structure, surface morphology, leakage current, ferroelectric properties, and optical properties of BiFeO3-based thin films were investigated. The substitution of Nd^3＋ ions for the Bi^3＋ site converts the structure from rhombohedral to coexisting tetragonal and orthorhombic. Nd doping improves the crystallinity of BiFeO3 thin films. The leakage current of Nd-doped BiFeO3 decreases by two to three orders of magnitude compared with that of pure BiFeO3. Among the samples, 15% Nd-doped BiFeO3 exhibits the strongest ferroelectric polarization of 17.96 μC/cm^2. Furthermore, the absorption edges of Bi1-xNdxFeO3 thin films show a slight red-shift after Nd doping.

Effect of Annealing Temperature on the Ferroelectric Properties of BiFeO_3 Thin Films Prepared by Sol-gel Process

Sol-gel process was adopted to prepare BiFeO3 films.BiFeO3 films were deposited on LaNiO3 coated Si（100） substrates annealed at 500 and 550 ℃,respectively.The X-ray diffraction results reveal that BiFeO3 film has a rhombohedrally distorted perovskite structure with space group R3c.The film annealed at 500 ℃ has larger remnant polarization（Pr） of 35.3 μC/cm2.For the film annealed at 550 ℃,smaller remnant polarization of Pr=4.8 μC/cm^2 is observed for its low breakdown electric field.Lower leakage conduction is observed in the film annealed at 500 ℃ at low applied field.

Thickness effect on solar-blind photoelectric properties of ultrathinβ-Ga_(2)O_(3)films prepared by atomic layer deposition

Theβ-Ga_(2)O_(3)films with different thicknesses are prepared by an atomic layer deposition system.The influence of film thickness on the crystal quality is obvious,indicating that the thicker films perform better crystal quality,which is verified from x-ray diffraction(XRD)and scanning electron microscope(SEM)results.The Ga_(2)O_(3)-based solar blind photodetectors with different thicknesses are fabricated and studied.The experimental results show that the responsivity of the photodetectors increases exponentially with the increase of the film thickness.The photodetectors with inter-fingered structure based on 900 growth cyclesβ-Ga_(2)O_(3)active layers(corresponding film thickness of 58 nm)exhibit the best performances including a low dark current of 134 fA,photo-to-dark current ratio of 1.5×10^(7),photoresponsivity of 1.56 A/W,detectivity of 2.77×10^(14)Jones,and external quantum efficiency of 764.49%at a bias voltage of 10 V under 254-nm DUV illumination.The photoresponse rejection ratio(R_(254)/R_(365))is up to 1.86×10^(5).In addition,we find that the photoelectric characteristics also depend on the finger spacing of the MSM structure.As the finger spacing decreases from 50μm to10μW,the photoresponsivity,detectivity,and external quantum efficiency increase significantly.

Off-stoichiometry indexation of BiFeO_3 thin film on silicon by Rutherford backscattering spectrometry

BiFeO3 is a multiferroic material with physical properties very sensitive to its stoichiometry.BiFeO3 thin films on silicon substrate are prepared by the sol–gel method combined with layer-by-layer annealing and final annealing schemes.X-ray diffraction and scanning electron microscopy are employed to probe the phase structures and surface morphologies.Using Rutherford backscattering spectrometry to quantify the nonstoichiometries of BiFeO3 thin films annealed at 100？C–650？C.The results indicate that Bi and Fe cations are close to the stoichiometry of BiFeO3,whereas the deficiency of O anions possibly plays a key role in contributing to the leakage current of 10^-5 A/cm^2 in a wide range of applied voltage rather than the ferroelectric polarizations of BiFeO3 thin films annealed at high temperature.

Centimeter-sized Cs_(3)Cu_(2)I_(5)single crystals grown by oleic acid assisted inverse temperature crystallization strategy and their films for high-quality X-ray imaging

Low-dimensional halide perovskites have become the most promising candidates for X-ray imaging,yet the issues of the poor chemical stability of hybrid halide perovskite,the high poisonousness of lead halides and the relatively low detectivity of the lead-free halide perovskites which seriously restrain its commercialization.Here,we developed a solution inverse temperature crystal growth(ITCG)method to bring-up high quality Cs_(3)Cu_(2)I_(5)crystals with large size of centimeter order,in which the oleic acid(OA)is introduced as an antioxidative ligand to inhibit the oxidation of cuprous ions effieiently,as well as to decelerate the crystallization rate remarkalby.Based on these fine crystals,the vapor deposition technique is empolyed to prepare high quality Cs_(3)Cu_(2)I_(5)films for efficient X-ray imaging.Smooth surface morphology,high light yields and short decay time endow the Cs_(3)Cu_(2)I_(5)films with strong radioluminescence,high resolution(12 lp/mm),low detection limits(53 nGyair/s)and desirable stability.Subsequently,the Cs_(3)Cu_(2)I_(5)films have been applied to the practical radiography which exhibit superior X-ray imaging performance.Our work provides a paradigm to fabricate nonpoisonous and chemically stable inorganic halide perovskite for X-ray imaging.

Optical and electrical properties of BaSnO_(3) and In_2O_(3) mixed transparent conductive films deposited by filtered cathodic vacuum arc technique at room temperature

For the crystalline temperature of BaSnO_(3)(BTO)was above 650℃,the transparent conductive BTO-based films were always deposited above this temperature on epitaxy substrates by pulsed laser deposition or molecular beam epitaxy till now which limited there application in low temperature device process.In the article,the microstructure,optical and electrical of BTO and In_(2)O_(3) mixed transparent conductive BaInSnO_(x)(BITO)film deposited by filtered cathodic vacuum arc technique(FCVA)on glass substrate at room temperature were firstly reported.The BITO film with thickness of 300 nm had mainly In_(2)O_(3) polycrystalline phase,and minor polycrystalline BTO phase with(001),(011),(111),(002),(222)crystal faces which were first deposited at room temperature on amorphous glass.The transmittance was 70%–80%in the visible light region with linear refractive index of 1.94 and extinction coefficient of 0.004 at 550-nm wavelength.The basic optical properties included the real and imaginary parts,high frequency dielectric constants,the absorption coefficient,the Urbach energy,the indirect and direct band gaps,the oscillator and dispersion energies,the static refractive index and dielectric constant,the average oscillator wavelength,oscillator length strength,the linear and the third-order nonlinear optical susceptibilities,and the nonlinear refractive index were all calculated.The film was the n-type conductor with sheet resistance of 704.7Ω/□,resistivity of 0.02Ω⋅cm,mobility of 18.9 cm2/V⋅s,and carrier electron concentration of 1.6×10^(19) cm^(−3) at room temperature.The results suggested that the BITO film deposited by FCVA had potential application in transparent conductive films-based low temperature device process.

XPS Study of Electroless Deposited Sb2Se3 Thin Films for Solar Cell Absorber Material

As a thin film solar cell absorber material, antimony selenide (Sb2Se3) has become a potential candidate recently because of its unique optical and electrical properties and easy fabrication method. X-ray photoelectron spectroscopy (XPS) was used to determine the stoichiometry and composition of electroless Sb2Se3 thin films using depth profile studies. The surface layers were analyzed nearly stoichiometric. But the abundant amount of antimony makes the inner layer electrically more conductive.

Corrosion characteristics of single-phase Mg-3Zn alloy thin film for biodegradable electronics

Biodegradable metals as electrodes, interconnectors, and device conductors are essential components in the emergence of transient electronics, either for passive implants or active electronic devices, especially in the fields of biomedical electronics. Magnesium and its alloys are strong candidates for biodegradable and implantable conducting materials because of their high conductivity and biocompatibility, in addition to their well-understood dissolution behavior. One critical drawback of Mg and its alloys is their considerably high dissolution rates originating from their low anodic potential, which disturbs the compatibility to biomedical applications. Herein, we introduce a single-phase thin film of a Mg-Zn binary alloy formed by sputtering, which enhances the corrosion resistance of the device electrode, and verify its applicability in biodegradable electronics. The formation of a homogeneous solid solution of single-phase Mg-3Zn was confirmed through X-ray diffraction and transmission electron microscopy. In addition, the dissolution behavior and chemistry was also investigated in various biological fluids by considering the effect of different ion species. Micro-tensile tests showed that the Mg-3Zn alloy electrode exhibited an enhanced yield strain and elongation in relation to a pure Mg electrode. Cell viability test revealed the high biocompatibility rate of the Mg-3Zn binary alloy thin film. Finally, the fabrication of a wireless heater demonstrated the integrability of biodegradable electrodes and highlighted the ability to prolong the lifecycle of thermotherapy-relevant electronics by enhancing the dissolution resistance of the Mg alloy.

High-performance omnidirectional self-powered photodetector constructed by CsSnBr_(3)/ITO heterostructure film

Omnidirectional photodetectors attract enormous attention due to their prominent roles in optical tracking systems and omnidirectional cameras.However,it is still a challenge for the construction of high-performance omnidirectional photodetectors where the incident light can be effectively absorbed in multiple directions and the photo-generated carriers can be effectively collected.Here,a high-performance omnidirectional self-powered photodetector based on the CsSnBr_(3)/indium tin oxide(ITO)heterostructure film was designed and demonstrated.The as-fabricated photodetector exhibited an excellent self-powered photodetection performance,showing responsivity and detectivity up to 35.1 mA/W and 1.82×10^(10) Jones,respectively,along with the smart rise/decay response time of 4 ms/9 ms.Benefitting from the excellent photoelectric properties of the CsSnBr_(3) film as well as the ability of the CsSnBr_(3)/ITO heterostructure to efficiently separate and collect photo-generated carriers,the as-fabricated photodetector also exhibited an excellent omnidirectional self-powered photodetection performance.All the results have certified that this work finds an efficient way to realize high-performance omnidirectional self-powered photodetectors.

Depth Profile Study of Electroless Deposited Sb2S3 Thin Films Using XPS for Photovoltaic Applications

Sb2S3 has gained tremendous research recently for thin film solar cell absorber material because of their easy synthesis, unique electrical and optical properties. The stoichiometry and composition of electroless Sb2S3 thin films were analyzed using XPS depth profile studies. The surface layers were found nearly stoichiometric. On the other hand, the inner layer was rich in antimony composition making it more conductive electrically.

Investigation of Sprayed Lu2O3 Thin Films Using XPS

Spray pyrolysis method was used to deposit Lutetium Oxide (Lu2O3) thin films using lutetium (III) chloride as source material and water as oxidizer. Annealing was carried out in argon atmosphere at 450°C for 60 minutes of the films. To investigate the composition and stoichiometry of sprayed as-deposited and annealed Lu2O3 thin films, depth profile studies using X-ray photoelectron spectroscopy (XPS) was done. Nearly stoichiometric was observed for both annealed and as-deposited films in inner and surface layers.

XPS Depth Profile Study of Sprayed Ga2O3 Thin Films

Ga2O3 thin films were fabricated by spray pyrolysis method using gallium acetylacetonate as source material and water as oxidizer. The films were annealed at 450°C for 60 minutes in argon atmosphere. X-ray photoelectron spectroscopy (XPS) depth profile studies were carried out to analyze the stoichiometry and composition of sprayed as-deposited and annealed Ga2O3 thin films. Surface layers and the inner layers of as-deposited and annealed films were found nearly stoichiometric.

纳米Cr_(2)O_(3)对铝合金微弧氧化膜组织和性能的影响

在恒流模式下对7050铝合金开展微弧氧化试验。用SEM、EDS、XRD、膜层测厚仪、维氏硬度计、电化学工作站和磨损试验机等研究了不同纳米Cr_(2)O_(3)含量对7050铝合金微弧氧化陶瓷膜组织和性能的影响。结果表明:添加纳米Cr_(2)O_(3)能减小陶瓷膜孔径,提升致密度,优化陶瓷膜结构;当纳米Cr_(2)O_(3)由1 g/L增至5 g/L时,陶瓷膜的厚度、硬度均先增后减;与未添加相比,添加纳米Cr_(2)O_(3)的陶瓷膜的耐蚀性和耐磨性均明显提升;陶瓷膜主要由γ-Al_(2)O_(3)相和少量的α-Al_(2)O_(3)相、莫来石相、Cr_(2)O_(3)相构成;总体来看,当纳米Cr_(2)O_(3)为3 g/L时,陶瓷膜的性能最优,厚度、显微硬度、自腐蚀电流和磨耗比分别为30.98μm、1273HV0.1、5.162×10^(-8)A/cm^(2)、0.0913%。

纳米TiO_(2)对NH_(3)-H_(2)O-LiBr工质降膜吸收性能的影响

为了探讨纳米TiO_(2)对三元NH_(3)-H_(2)O-LiBr工质降膜吸收的影响,本文利用数值分析建立了三元工作流体薄膜吸收的连续方程、能量方程和组分质量平衡方程,采用Matlab软件进行编程和计算纳米流体的降膜吸收性能,将其与实验数据进行对比验证,并进一步分析了纳米TiO_(2)质量分数、初始氨浓度、初始温度、冷却水进口温度、吸收压力和下降薄膜管长度对薄膜吸收性能的影响。研究表明:添加纳米TiO_(2)可以增强降膜吸收的传质速率,主要原因为液膜中氨的扩散系数增加。当纳米TiO_(2)质量分数从0%增加到0.1%、0.3%和0.5%时,扩散系数分别增加了3.44倍、6.42倍和11.76倍。此外,增加初始氨浓度、降低初始温度、提高冷却水进口温度或降低吸收压力都可以提高最终溶液的饱和度。