Improved chirp scaling algorithm integrated motion compensation for parallel-track bistatic synthetic aperture radar

To compensate motion errors of images from the parallel-track bistatic synthetic aperture radar（BiSAR）,an improved chirp scaling algorithm（CSA） is proposed.Since velocity vector of the moving aircrafts in the parallel-track BiSAR system can not remain invariant in an aperture,an actual aperture is divided into subapertures so that it is reasonable to assume that the aircrafts move with constant acceleration vector in a subaperture.Based on this model,an improved CSA is derived.The new phase factors incorporate three-dimensional acceleration and velocity.The motion compensation procedure is integrated into the CSA without additional operation required.The simulation results show that the presented algorithm can efficiently resolve motion compensation for parallel-track BiSAR.

Spatial Channel Sounding Based on Bistatic Synthetic Aperture Radar Principles

In this paper, we propose a simplified spatial channel sounding method by utilizing bistatic synthetic aperture radar(BiSAR) principles. Despite the different deployment geometries compared with a conventional BiSAR system, the feasibility of the approach is established by 1) the proposed method achieves a better spatial resolution than conventional directional channel sounders and 2) reconstruction algorithms based on time-domain backprojection in conjunction with a digital elevation model provide a good imaging performance and are suitable for reconstructing the spatial distribution of scatterers. Simulations of a high-speed rail(HSR) scenario demonstrate that the estimated power delay profiles(PDPs) and power angle profiles(PAPs) are close to the actual values.

New Precision Guidance Method Based on Bistatic Synthetic Apterture Radar

A new method is presented to improve guidance precision. This method is based on bistatic synthetic aperture radar. The illuminator works in side looking mode, providing the synthetic aperture and the receiver is disposed on the seeker which operates in the forward looking mode. The receiving antenna is composed of four sub-antennas and so four synthetic aperture radar （SAR） images are to be generated. Target is positioned in SAR images by image matching. The bearing and elevation of image element of target are measured by the principle of monopulse angular measurement. Theory of the proposed method is derived and simulation on bearing measurement is done. Simulation shows that the method is valid and if SNR of target＇s image is above 30 dB, the angular measuring difference is within the confines of 0.04 degree.

Design Bistatic Interferometric DEM Generation Algorithm and Its Theoretical Accuracy Analysis for LuTan-1 Satellites

LuTan-1(LT-1)is a constellation with two full-polarization L-band radar satellites designed by China,and the first satellite was scheduled to be launched in December 2021 and the second one in January 2022.The LT-1 will be operated for deformation monitoring in repeat-pass mode,and for DEM generation in bistatic mode,improving self-sufficiency of SAR data for the field of geology,earthquake,disaster reduction,geomatics,forestry and so on.In this paper,we focused on designing an algorithm for interferometric DEM generation using LT-1 bistatic satellites.The basic principle,main error sources and errors control of the DEM generation algorithm of LT-1 were systematically analyzed.The experiment results demonstrated that:①The implemented algorithm had rigorous resolution with a theoretic accuracy better than 0.03 m for DEM generation.②The errors in satellite velocity and Doppler centroid had no obvious effect on DEM accuracy and they could be neglected.While the errors in position,baseline,slant range and interferometric phase had a significant effect on DEM accuracy.And the DEM error caused by baseline error was dominated,followed by the slant range error,interferometric phase error and satellite position error.③To obtain an expected DEM accuracy of 2 m,the baseline error must be strictly controlled and its accuracy shall be 1.0 mm or better for Cross-Track and Normal-Direction component,respectively.And the slant range error and interferometric phase error shall be reasonably controlled.The research results were of great significance for accurately grasping the accuracy of LT-1 data products and their errors control,and could provide a scientific auxiliary basis for LT-1 in promoting global SAR technology progress and the generation of high-precision basic geographic data.

Doppler Properties of Spaceborne/Airborne Hybrid Bistatic Synthetic Aperture Radar

In this paper,a special geometry case of spaceborne-airborne bistatic SAR(SA-BiSAR) is considered,in which satellite and aircraft flight paths are parallel and their antennas are steering at the strip map.This case is a simple but typical application example,which is applicable for non-cooperative illumination.The integration time of SA-BiSAR system is derived via the motion of transmitter and receiver footprint.In parallel and stripmap mode,Doppler frequency is obtained through the combination be-tween spaceborne and airborne SAR.Other Doppler properties have been envisaged,including Doppler bandwidth and azimuth resolution.The overall simulation experiments are conducted and some characteristics are exhibited.The critical parameters,which have the significant effect on the SA-BiSAR Doppler properties,are extracted by analytical expressions and numerical simulations.In parallel and strip map mode and with reference to ENVISAT-1,SA-BiSAR system possesses the potential of yielding 10 m azi-muth resolution and 0.5 s integration time for C-band via the analysis of simulation results.

Focusing Azimuth-Invariant Bistatic Synthetic Aperture Radar Data Based on a Polynomial Model

In this paper,a focusing approach is presented to widen the use of efficient monostatic imaging algorithms for azimuth-invariant bistatic synthetic aperture radar(SAR) data.The bistatic range history is modeled by a polynomial of azimuth time.Using this model,an analytic form of the signal spectrum in the 2D frequency domain is derived,and a simple single-valued relation between the transmitter and receive ranges is established.In this way,a lot of monostatic image formation algorithms can be extended for the bistatic SAR data,and a bistatic chirp scaling algorithm is developed as an application of the new approach.This algorithm can be used to process the azimuth-invariant bistatic configuration where the transmitter and receiver platforms are moving on parallel tracks with the same velocity.In addition,some simulation results are given to demonstrate the validity of the proposed approach.

A jamming method against bistatic SAR based on modulation theory

This paper focuses on the jamming problem of bistatic synthetic aperture radar (BiSAR), and a jamming method against BiSAR based on modulation theory is proposed. The proposed jamming method modulates the BiSAR signal with the cosinusoidal phase to generate multi-false targets in range, and further rotates the jammer to generate multi-false targets in azimuth. The range multi-false targets and azimuth multi-false targets form the two-dimensional cover jamming or deception jamming, which can protect the important targets efficiently. The number of false targets, the interval of false targets, and the jamming square can be adjusted flexibly by setting different range jamming parameters and azimuth jamming parameters. The jamming performance and the choosing criteria of jamming parameters are also discussed. Finally, the simulated data verify the effectiveness of the jamming method.

多时相Sentinel-1影像反演玉溪典型烟区烤烟种植分布的方法

为准确识别烤烟种植分布特征,基于2020年玉溪烤烟大田生长期不同时相的11景Sentinel-1卫星影像,结合野外实地调研,分析不同土地利用类型合成孔径雷达(SAR)极化信息的可区分度,并结合70%样地训练随机森林分类方法提取不同土地利用的分布范围,最后用30%调研样地验证烤烟种植的提取精度。结果表明,垂直发射垂直接收(VV)相较于垂直发射水平接收(VH)更能区分不同土地利用类型,VH、VV、VV+VH和VV+VH+VV/VH四种极化信息组合方式中,地物分类精度最高的为VV+VH组合,总体分类精度为87.6%,Kappa系数为0.847,其中,烤烟种植识别的制图精度为96.3%,用户精度为89.4%。在玉溪典型烟区采用多时相SAR识别烤烟种植分布,识别准确率基本能满足区域烤烟种植识别的精度要求。

RESEARCH ON THE BISTATIC FORWARD-LOOKING SAR IMAGING

The bistatic Synthetic Aperture Radar (SAR) systems with separate transmitter and receiver antennas provide a new potential to imaging in the forward-looking geometry. Analysis of the Doppler property in this paper indicates the feasibility of Bistatic Forward-Looking (BFL) SAR imaging. Considering the different Doppler property determined by the two platforms in BFL SAR, a new 2-D point target spectrum is derived in our study. Based on the spectrum, an imaging method is chosen for the configuration, and the point target simulation validates the analysis.

Nonlinear RCMC method for spaceborne/airborne forward-looking bistatic SAR

In the spaceborne/airborne forward-looking bistatic syn- thetic aperture radar （SA-FBSAR）, due to the system platforms＇ remarkable velocity difference and the forward-looking mode, the range cell migration （RCM） not only depends on the target＇s two- dimensional location, but also varies with the range location non- linearly. And the nonlinearity is not just the slight deviation from the linear part, but exhibits evident nonlinear departure in the RCM trajectory. If the RCM is not properly corrected, nonlinear image distortions would occur. Based on the RCM model, a modified two-step RCM compensation （RCMC） method for SA-FBSAR is proposed. In this method, firstly the azimuth-dependent RCM is compensated by the scaling Fourier transform and the phase multi- plication. And then the range-dependent RCM is removed through interpolation. The effectiveness of the proposed RCMC method is verified by the simulation results of both point scatterers and area targets.

哨兵1号的对流层湿延迟变化提取与分析

为了进一步提高大气水汽反演的精度和可靠性,提出一种利用星载干涉合成孔径雷达(InSAR)提取对流层天顶湿延迟(ZWD,简称对流层湿延迟)的方法:以2020年1月至2020年3月覆盖济南及周边地区的哨兵1号卫星(Sentinel-1)数据为基础,采用欧洲中期天气预报中心(ECMWF)第五代全球气候的大气再分析资料(ERA5)计算对流层干延迟分量;再利用双线性插值方法统一干延迟分量与Sentinel-1的分辨率;然后通过差分数据处理实现InSAR干涉图相位中对流层湿延迟分量的提取。实验结果表明,Sentinel-1数据可以在较高的空间分辨率内有效提取对流层湿延迟;InSAR技术与北斗卫星导航系统(BDS)技术探测的天顶方向对流层湿延迟变化趋势一致,且对流层湿延迟含量逐渐升高;2种探测手段的对流层湿延迟结果平均偏差为4.45~9.03 mm,最小偏差可达0.3 mm,二者相关系数为0.79。利用InSAR技术结合Sentinel-1等数据可以提取高精度、空间连续对流层湿延迟,可为大范围、空间连续的大气水汽反演提供数据支撑。

Phase synchronization processing method for alternating bistatic mode in distributed SAR

In the distributed synthetic aperture radar （SAR）, the alternating bistatic mode can perform phase reference without a synchronization link between two satellites compared with the pulsed alternate synchronization method. The key of the phase synchronization processing is to extract the oscillator phase differences from the bistatic echoes. A signal model of phase synchronization in the alternating bistatic mode is presented. The phase synchronization processing method is then studied. To reduce the phase errors introduced by SAR imaging, a sub-aperture processing method is proposed. To generalize the sub-aperture processing method, an echo-domain processing method using correlation of bistatic echoes is proposed. Finally, the residual phase errors of the both proposed processing methods are analyzed. Simulation experiments validate the proposed phase synchronization processing method and its phase error analysis results.

3D motion and geometric information system of single-antenna radar based on incomplete 1D range data

A 3D motion and geometric information system of single-antenna radar is proposed,which can be supported by spotlight synthetic aperture radar（SAR） system and inverse SAR（ISAR） system involving relative 3D motion of the rigid target.In this system,applying the geometry invariance of the rigid target,the unknown 3D shape and motion of the radar target can be reconstructed from the 1D range data of some scatterers extracted from the high-resolution range image.Compared with the current 1D-to-3D algorithm,in the proposed algorithm,the requirement of the 1D range data is expanded to incomplete formation involving large angular motion of the target and hence,the quantity of the scatterers and the abundance of 3D motion are enriched.Furthermore,with the three selected affine coordinates fixed,the multi-solution problem of the reconstruction is solved and the technique of nonlinear optimization can be successfully utilized in the system.Two simulations are implemented which verify the higher robustness of the system and the better performance of the 3D reconstruction for the radar target with unknown relative motion.

Property analysis of bistatic forward-looking SAR with arbitrary geometry

Bistatic forward-looking synthetic aperture radar（SAR） has many advantages and applications owing to its twodimensional imaging capability.There could be various imaging configurations because of the geometric flexibility of bistatic platforms,resulting in kinds of models built independently among which there could be some similar even the same motion features.Comprehensive research on such systems in a more comprehensive and general point of view is required to address their difference and consistency.Property analysis of bistatic forwardlooking SAR with arbitrary geometry is achieved including stripmap and spotlight modes on airborne platform,missile-borne platform,and hybrid platform of both.Emphasis is placed on azimuth space variance of some key parameters significantly affecting the subsequent imaging processing,based on which the frequency spectra are further described and compared considering respective features of different platforms for frequency imaging algorithm developing.Simulation results confirm the effectiveness and correctness of our analysis.

Resolution analysis of GEO spaceborne-airborne bistatic SAR based on sliding spotlight mode

For a synthetic aperture radar（SAR） system mounted on a geostationary Earth orbit（GEO） satellite, the track can be curvilinear. Thus, a bistatic SAR system based up on geostationary transmitter and ＂receive-only＂ SAR system onboard airplanes, namely GEO spaceborne-airborne bistatic（GEO SA-Bi SAR）, is significantly different from the traditional bistatic SAR. This paper mainly studies the resolution characteristic of the sliding spotlight GEO SA-Bi SAR system. Firstly, the common azimuth coverage and coherent accumulated time are theoretically analyzed in detail. Then,based on the gradient method, the accurate two dimensional resolution of a GEO SA-Bi SAR system is analytically calculated. Finally, the simulation data show the correctness and effectiveness of the proposed resolution analysis method.

Improved chirp scaling algorithm for parallel-track bistatic SAR

The curvature factor of the parallel-track bistatic SAR is range dependent, even without variation of the effective velocity. Accounting for this new characteristic, a parallel-track chirp scaling algorithm （CSA） is derived, by introducing the method of removal of range walk （RRW） in the time domain. Using the RRW before the CSA, this method can reduce the varying range of the curvature factor, without increasing the computation load obviously. The azimuth dependence of the azimuth-FM rate, resulting from the RRW, is compensated by the nonlinear chirp scaling factor. Therefore, the algorithm is extended into stripmap imaging. The realization of the method is presented and is verified by the simulation results.

Temporal decorrelation model for the bistatic SAR interferometry

This paper develops a temporal decorrelation model for the bistatic synthetic aperture radar（BSAR） interferometry. The temporal baseline is one of the important decorrelation sources for the repeat-pass synthetic aperture radar（SAR） interferometry. The study of temporal decorrelation is challenging, especially for the bistatic configuration, since temporal decorrelation is related to the data acquisition geometry. To develop an appropriate theoretical model for BSAR interferometry, the existing models for monostatic SAR cases are extended, and the general BSAR geometry configuration is involved in the derivation. Therefore, the developed temporal decorrelation model can be seen as a general model.The validity of the theoretical model is supported by Monte Carlo simulations. Furthermore, the impacts of the system parameters and BSAR geometry configurations on the temporal decorrelation model are discussed briefly.

New analytical imaging algorithm for general case airborne bistatic SAR

This paper focuses on the general case （GC） airborne bistatic synthetic aperture radar （SAR） data processing, and a new analytical imaging algorithm based on the extended Loffeld＇s bistatic formula （ELBF） is proposed. According to the bistatic SAR geometry, the track decoupling formulas that convert the bistatic geometry to the receiver-referenced geometry in a concise way are derived firstly. Then phase terms of ELBF are decomposed into two independent phase terms as the range phase term and the azimuth phase term in a new way. To get the focusing result, the bistatic deformation （BD） term is compensated in the two-dimensional （2- D） frequency domain, and the space-variances of the range phase term and the azimuth phase term are eliminated by chirp scaling （CS） and chirp z-transform （CZT）, respectively. The effectiveness of the proposed algorithm is verified by the simulation results.

Three-dimensional bistatic interferometric ISA Rimaging

An approach based on interferometry technique is proposed for three-dimensional （3D） bistatic inverse synthetic aperture radar （ISAR） imaging. It is converted to a monostatic problem by using the theory that a bistatic radar equals a monostatic radar located on the bisector of bistatic an- gle. Then, interferometric phases extracted from a pair of cross shaped antennas are used to esti- mate the height and associated rotational velocity. Finally, numerical simulations are provided to e- valuate this method.

Monostatic and Bistatic Low Frequency Ultrawideband SAR Imaging Experiment

Low frequency ultrawideband (LF UWB) synthetic aperture radar (SAR) has lately become of a particular interest to SAR community. Monostatic and bistatic LF UWB SAR system has the well foliage penetrating capability, high-resolution imaging and providing the increased information. In 2015, a monostatic and bistatic LF UWB SAR imaging experiment was conducted. In this experiment, the monostatic and bistatic data were collected simultaneously by operating a moving vehicle-based radar in the SAR mode, in conjunction with a stationary ground-based receiver. The aim was to investigate the imaging property of the bistatic LF UWB SAR system. The one pulse per second (1 PPS) signal in combination with the global position system (GPS) disciplined 100 MHz oscillator from the GPS receivers was used to implement the time and frequency synchronization in this SAR system. The bistatic SAR image was obtained by the subaperture spectrum-equilibrium method integrated with the fast factorized back projection (FFBP) algorithm. Bistatic experiment results are show to prove the validity of the bistatic LF UWB SAR imaging experiment.