Robust Nonlinear Current Sensorless Control of the Boost Converter with Constant Power Load

The boost converter feeding a constant power load (CPL) is a non-minimum phase system that is prone to the destabilizing effects of the negative incremental resistance of the CPL and presents a major challenge in the design of stabilizing controllers. A PWM-based current-sensorless robust sliding mode controller is developed that requires only the measurement of the output voltage. An extended state observer is developed to estimate a lumped uncertainty signal that comprises the uncertain load power and the input voltage, the converter parasitics, the component uncertainties and the estimation of the derivative of the output voltage needed in the implementation of the controller. A linear sliding surface is used to derive the controller, which is simple in its design and yet exhibits excellent features in terms of robustness to external disturbances, parameter uncertainties, and parasitics despite the absence of the inductor’s current feedback. The robustness of the controller is validated by computer simulations.

Design of Second Order Sliding Mode and Sliding Mode Algorithms:A Practical Insight to DC-DC Buck Converter

This paper presents a simple and systematic approach to design second order sliding mode controller for buck converters.The second order sliding mode control(SOSMC)based on twisting algorithm has been implemented to control buck switch mode converter.The idea behind this strategy is to suppress chattering and maintain robustness and finite time convergence properties of the output voltage error to the equilibrium point under the load variations and parametric uncertainties.In addition,the influence of the twisting algorithm on the performance of closed-loop system is investigated and compared with other algorithms of first order sliding mode control such as adaptive sliding mode control(ASMC),nonsingular terminal sliding mode control(NTSMC).In comparative evaluation,the transient response of the output voltage with the step change in the load and the start-up response of the output voltage with the step change in the input voltage of buck converter were compared.Experimental results were obtained from a hardware setup constructed in laboratory.Finally,for all of the surveyed control methods,the theoretical considerations,numerical simulations,and experimental measurements from a laboratory prototype are compared for different operating points.It is shown that the proposed twisting method presents an improvement in steady state error and settling time of output voltage during load changes.

Mode shift and stability control of a current mode controlled buck-boost converter operating in discontinuous conduction mode with ramp compensation

By establishing the discrete iterative mapping model of a current mode controlled buck-boost converter, this paper studies the mechanism of mode shift and stability control of the buck-boost converter operating in discontinuous conduction mode with a ramp compensation current. With the bifurcation diagrazn, Lyapunov exponent spectrum, time- domain waveform and parameter space map, the performance of the buck-boost converter circuit utilizing a compensating ramp current has been analysed. The obtained results indicate that the system trajectory is weakly chaotic and strongly intermittent under discontinuous conduction mode. By using ramp compensation, the buck-boost converter can shift from discontinuous conduction mode to continuous conduction mode, and effectively operates in the stable period-one region.

Study of Sliding Mode Control of DC-DC Buck Converter

In this paper, a robust sliding mode controller for the control of dc-dc buck converter is designed and analyzed. Dynamic equations describing the buck converter are derived and sliding mode controller is designed. A two-loop control is employed for a buck converter. The robustness of the sliding mode controlled buck converter system is tested for step load changes and input voltage variations. The theoretical predictions are validated by means of simulations. Matlab/Simulink is used for the simulations. The simulation results are presented. The buck converter is tested with operating point changes and parameter uncertainties. Fast dynamic response of the output voltage and robustness to load and input voltage variations are obtained.

Paralleled DC-DC Power Converters Sliding Mode Control with Dual Stages Design

This paper proposes the new cascaded series parallel design for improved dynamic performance of DC-DC buck boost converters by a new Sliding Mode Control (SMC) method. The converter is controlled using Sliding Mode Control method that utilizes the converter’s duty ratio to determine the skidding surface. System modeling and simulation results are presented. The results also showed an improved overall performance over typical PID controller, and there was no overshoot or settling time, tracking the desired output nicely. Improved converter performance and robustness were expected.

Sampled-data modeling and dynamical effect of output-capacitor time-constant for valley voltage-mode controlled buck-boost converter

By analyzing the output voltage ripple of a buck-boost converter with large equivalent series resistance（ESR） of output capacitor, one valley voltage-mode controller for buck-boost converter is proposed. Considering the fact that the increasing and decreasing slopes of the inductor current are assumed to be constant during each switching cycle, an especial sampleddata model of valley voltage-mode controlled buck-boost converter is established. Based on this model, the dynamical effect of an output-capacitor time-constant on the valley voltage-mode controlled buck-boost converter is revealed and analyzed via the bifurcation diagrams, the movements of eigenvalues, the Lyapunov exponent spectra, the boundary equations,and the operating-state regions. It is found that with gradual reduction of output-capacitor time-constant, the buck-boost converter in continuous conduction mode（CCM） shows the evolutive dynamic behavior from period-1 to period-2, period-4, period-8, chaos, and invalid state. The stability boundary and the invalidated boundary are derived theoretically by stability analysis, where the stable state of valley voltage-mode controlled buck-boost converter can enter into an unstable state, and the converter can shift from the operation region to a forbidden region. These results verified by time-domain waveforms and phase portraits of both simulation and experiment indicate that the sampled-data model is correct and the time constant of the output capacitor is a critical factor for valley voltage-mode controlled buck-boost converter, which has a significant effect on the dynamics as well as control stability.

Enhancing the Performance of the Marine and Tidal Current Converters Using DC-DC Boost Converter

Due to the highly demand on the renewable energy sources as a free and a clean power resource, extracting energy from unsteady flow using marine and tidal current turbines has a distinct focusing nowadays. For their resource characteristic, extracting energy from marine/tidal current needs a simple and robust converter, which could overcome the drawbacks of the mechanical system such as gearbox and enhance conversion system stability. In this paper a new AC-DC-AC conversion system has been proposed. The new conversion system contains a middle stage DC-DC boost converter, which boost the generated rectified DC voltage higher enough that can enable the PWM inverter to generate the required voltage with the synchronized frequency. In order to investigate the efficient performance of the proposed conversion system especially at low current speed compared to the conventional one, different operating conditions have been studied. Moreover, the effect of including boost converter on the THD （total harmonic distortion） has also been checked. The new conversion system presents its capability to enhance and improve system performance not only with low current speed but also with high current speed.

Simulation of multiphase boost DC-DC converter with the stable control strategy

The multiphase boost DC-DC converter with stable control strategy is presented. Multi- phase boost DC-DC converter is designed for high voltage and high power applications, and could be achieved by the adjustment of voltage doubler rectifiers on the secondary side of high frequency transformers. The stable control strategy for three phase boost DC-DC converter has been utilized during simulation in this study and this strategy can be extend to N-number of phases. The stable control strategy consists of only three voltage loops, which are sufficient for appropriate and efficient operation of three phase boost DC-DC converter. With the stable control strategy, the equal power balance sharing can be obtained between input and output. The stability of control strategy has been evaluated by simulating the multiphase boost DC-DC converter for the same and mismatch turn ratios of high frequency transformers. The simulation result is good and the objective of the strategy is a- chieved.

Inductor Current Sampled Feedback Control of Chaos in Current-Mode Boost Converter

A chaos control strategy for chaotic current-mode boost converter is presented by using inductor current sampled feedback control technique.The quantitative analysis of control mechanism is performed by establishing a discrete alterative map of the controlled system.The stability criterion,feedback gain,and corresponding critical duty ratio are obtained from the eigenvalue of the map.The simulation results verify the t heoretical analysis results of the control strategy.

Investigation of the Mechanism of Tangent Bifurcation in Current Mode Controlled Boost Converter

Tangent bifurcation is a special bifurcation in nonlinear dynamic systems. The investigation of the mechanism of the tangent bifurcation in current mode controlled boost converters operating in continuous conduction mode (CCM) is performed. The one-dimensional discrete iterative map of the boost converter is derived. Based on the tangent bifurcation theorem, the conditions of producing the tangent bifurcation in CCM boost converters are deduced mathematically. The mechanism of the tangent bifurcation in CCM boost is exposed from the viewpoint of nonlinear dynamic systems. The tangent bifurcation in the boost converter is verified by numerical simulations such as discrete iterative maps, bifurcation map and Lyapunov exponent. The simulation results are in agreement with the theoretical analysis, thus validating the correctness of the theory.

SLIDE-MODE CONTROL SCHEME WITH DYNAMIC MODIFYING ERRORS FOR BOOST CONVERTER

A novel control scheme is presented by using sliding-mode control for boost converter operating in continuous conduction mode (CCM). Although the non-ideal switching condition and physical constraint of the control are considered on the base of equivalent control, the scheme is still simple. By modifying the sliding-modc errors in each switching period, the steady-state errors and chattering can be substantially reduced. Simulation results confirm the theoretical analysis and show the improvement of the converter’s start-up behavior and low sensitivity to external perturbation.

Design and Simulation of a Solar Regulator Based on DC-DC Converters Using a Robust Sliding ModeController

The MPPT （maximum power point tracking） is one of the most important features of a regulator system that processes the energy produced by a photovoltaic generator. It is necessary, in fact, to design a controller that is able to set the output value of the voltage and ensure the working within the maximum power point. In this paper, we propose the application of the robust sliding mode control technique to a DC-DC buck converter which is combined with a classical P ＆ O （perturbation and observation） algorithm to enhance the solar system efficiency. Dynamic equations describing the boost converter are derived and a sliding mode controller for a buck converter is designed. It is shown that, this control approach gives good results in terms of robustness toward load and input voltage variations. The effectiveness of the proposed work is verified by the simulation results under PowerSim environment.

Boost DC-DC变换器连续导电模式解析

DC-DC变换器是“电力电子技术基础”课程的重要入门变换器,优选教学内容并合理布局,有助于学生养成良好的学习和思维习惯。根据电感电流的连续性以及负载电阻供电来源的差异性,Boost DC-DC变换器具有多种工作模式,包括连续导电模式(CCM)、临界导电模式(CRM)和断续导电模式(DCM)。其中CCM又可分为电感完全供能模式(CCM-CISM)和电感不全供能模式(CCM-IISM)。在理论分析和推导CCM-CISM与CCM-CISM临界电感表达式基础上,对几种典型工作模式采用Matlab/Simulink进行仿真验证。所得结果有助于加深学生对Booost DC-DC变换器工作原理的理解,引导学生学会深度思考和自行仿真验证随时产生的设想。

Overview of Boost Converters for Photovoltaic Systems

DC-DC boost power converters play an important role in solar power systems;they step up the input voltage of a solar array for a given set of conditions. This paper presents an overview of the variance boost converter topologies. Each boost converter is evaluated on its capability to operate efficient, size, and cost of implementation. Conventional boost converter and interleaved boost converter are widely used topologies in photovoltaic systems reported;however, they have negative sides of varied efficiency level under changed weather conditions. Therefore, this paper proposes, interleaved boost converter with novel switch adaptive control, to maximise efficiency of standalone photovoltaic system under change of solar power levels, due to illadation condition.

The Usage of the Digital Controller in Regulating Boost Converter

This paper proposes the modeling and simulation technique to analyze and design a Boost converter using generalized minimum variance method with discrete-time quasi-sliding mode to adjust the converter switch through a pulse width modulation (PWM), so as to enhance a stable output voltage. The control objective is to maintain the sensed output voltage stable, constant and equal to some constant reference voltage (8 volt) in the load resistance variation (24, 48, 240) Ω and input voltage variation (20, 24, 28) volt circumstances. This control strategy is very appropriate for the digitally controlled power converter and for the system requirement accomplishment, resulting high output voltage accuracy. The performance degradation in practical implementation can be expected due to noise, PWM nonlinearities, and components imperfection. The digital simulation using MATHLAB/Simulink is performed to validate the functionality of the system.

Design and Experimentation of FPGA-Based Soft-Switched Interleaved Boost Converter for Telecommunication System

This paper proposes the design and experimentation of digital control of soft-switched interleaved boost converter using FPGA for Telecommunication System. The switching devices in the proposed converter are turned on and off with Zero Voltage Switching (ZVS) and Zero Current Switching (ZCS) respectively. The circuit is operated in Continuous Conduction Mode (CCM) with various load ranges having duty cycle of more than 50%. The proposed converter is studied by developing the simulation module in MATLAB/SIMULINK. A PI controller is designed and implemented in FPGA to obtain a regulated DC output for line and load variations. Simulation and experimentation results are verified with a prototype development of the proposed converter. The results indicate that the converter performance is enhanced with closed loop control.

Proposal of High Gain, Reduced Stress with Low-Duty-Cycle Two-Input Boost Converter for Renewable Energy Systems

A two-input boost converter with voltage multiplier cell is proposed in this paper. Then a family of two-input converters with and without voltage multiplier cell are derived and their results are compared to achieve high voltage gain, low duty cycle, and reduced voltage stress. From the analysis of different topologies, a modified two-input converter with two-stage voltage multiplier cell has good operating characteristics. The switch voltage stress and duty cycle of the modified converter is significantly very less than that of the other converter topologies. The modified DC-DC converter with 50% duty cycle achieves a voltage gain of 10 and the results are verified by using MATLAB/Simulink software.

Constant Ripple Current Control for Switching DC-DC Converter

The adapted DC-DC converters should be smaller in size and have a small output current ripple to meet the increasing demand for low voltages with high performance and high density micro processors for several microelectronic load applications. This paper proposes a DC-DC converter using variable on-time and variable switching frequency control enhanced constant ripple current control and reduced magnetic components. The proposed converter is realized by making the turn-offtime proportional to the on-time of the converter, according to the input and output voltage, thereby reducing the corresponding current ripple on output voltage in the continuous conduction mode. A Buck DC-DC converter using the proposed control strategy is analyzed in detail, along with some experimental results to show the performance and effectiveness of this converter.

Estimation of Boost Converter State-Space Variables Using Fast Output Sampling Method

In this paper a fast output sampling （FOS） estimator is designed for estimation of state-space variables of DC-DC boost converter. Estimated state-space variables are output voltage of the converter and its first derivative, which are suitable for model reference adaptive controllers and sliding mode controllers design. Estimator is designed for operation in continuous and discontinuous conduction modes. The simulation results show that proposed FOS estimator provides good estimation of state-space variables despite the voltage ripple caused by high frequency switching in converter and disturbances （change of load and input voltage）.

A Dual-Mode Step-up DC/DC Converter IC with Current-Limiting and EMI Reduction Techniques

This paper presents a novel dual-mode step-up （boost） DC/DC converter. Pulse-frequency modulation （PFM） is used to improve the efficiency at light load. This converter can operate between pulse-width modulation （PWM） and pulse-frequency modulation. The converter will operate in PFM mode at light load and in PWM mode at heavy load. The maximum conversion efficiency of this converter is 96%. The conversion efficiency is greatly improved when load current is below 100 mA. Additionally, a soft-start circuit and a variable-sawtooth frequency circuit are proposed in this paper. The former is used to avoid the large switching current at the start up of the converter and the latter is utilized to reduce the EMI of the converter.