Bulk flow model with perturbation simplification has been used to calculate rotordynamic coefficients in annular seals which have significant influences on the dynamic behavior of rotors in turbomachinery. In this wor...Bulk flow model with perturbation simplification has been used to calculate rotordynamic coefficients in annular seals which have significant influences on the dynamic behavior of rotors in turbomachinery. In this work, a transient bulk flow model with arbitrary rotor motion is developed, and the boundary conditions and friction factor in the model are calibrated with steady Computational Fluid Dynamics（CFD） analysis. The numerical solution scheme is developed based on the finite element method to obtain the transient reaction force in the seal clearance. With a periodic circular rotor orbit, the transient forces at multiple whirling frequencies are used to evaluate the rotordynamic coefficients. The leakage flowrate of CFD analysis has good agreement with experimental results and the calibrated parameters in bulk flow model are dependent on operating conditions. Although CFD calibration improves the accuracy of the perturbed bulk flow model, the direct damping is overestimated and the cross-coupled damping is underestimated. Compared with the perturbed model, the predictions of the transient bulk flow model are more agreeable with the experiment.展开更多
This paper using the dataset of BBFs (bursty bulk flows) observed by two Cluster satellites C1 and C4 studies the difference between onset times of BBFs observed by C1 and C4. It is found that the onset time differenc...This paper using the dataset of BBFs (bursty bulk flows) observed by two Cluster satellites C1 and C4 studies the difference between onset times of BBFs observed by C1 and C4. It is found that the onset time differences of most of BBFs observed by C1 and C4 are smaller than 60 s. The average onset time difference of BBFs of C1 and C4 is 68.5 s. The probabilities of onset time difference of BBFs of C1 and C4 larger than 30 60 90 and 120 s are respectively 55% 35% 27% and 23%. The largest onset time difference of BBFs of C1 and C4 decreases with the increase of earthward component of maximum velocities of BBFs. The onset time difference of BBFs of C1 and C4 results from the velocity inhomogeneity inside the flow channel of BBF which may be produced in propagation path and/or in source region of BBFs. Such a wide range of onset time difference of BBFs suggests that the velocity inhomogeneity inside the flow channel of BBF is various. These results are very important to the current study of substorm research based on THEMIS data because they indicate that it is impossible to determine the onset time of BBF with a single satellite.展开更多
La57.6Al17.5(Cu,Ni)24.9 and La64Al14(Cu,Ni)22 bulk metallic glasses (BMGs) were prepared by copper-mould casting method. Plastic deformation behavior of the two BMGs at various loading rates was studied by nanoindenta...La57.6Al17.5(Cu,Ni)24.9 and La64Al14(Cu,Ni)22 bulk metallic glasses (BMGs) were prepared by copper-mould casting method. Plastic deformation behavior of the two BMGs at various loading rates was studied by nanoindentation. The results showed that the La57.6Al17.5(Cu,Ni)24.9 BMG with a glass transition temperature of 423 K exhibited prominent serrated flow at low loading rates, whereas less pronounced serrated flow at high rates during nanoindentation. In contrast, the La64Al14(Cu,Ni)22 BMG with a glass transition temperature of 401 K exhibited prominent serrated flow at high loading rates. The different rate dependency of serrated flow in the two La-based BMGs is related to the different glass transition temperature, and consequently the degree of viscous flow during indentation at room temperature. A smoother flow occurs in the alloy with relatively lower glass transition temperature, due to the relaxation of stress concentration.展开更多
Research results on the viscous flow deformation behavior of bulk amorphous alloy in different systems are reviewed. The material exhibits an ideal Newtonian fluid at a high temperature. Analytical solution of lamella...Research results on the viscous flow deformation behavior of bulk amorphous alloy in different systems are reviewed. The material exhibits an ideal Newtonian fluid at a high temperature. Analytical solution of lamellar fluid flow behavior is used to discuss the viscous flow behavior of the bulk amorphous alloy in the supercooled liquid state. A material model, which describes such deformation behavior of Mg6oCusoYlo amorphous alloy, is introduced into the finite element method of microformin8 process. Surface feature size was investigated and found not sensitive to the micro formability. Bulk amorphous alloy may possibly be applied to microelectro-mechanical-systems （MEMS） fabrication.展开更多
Copper-nickel nanoparticle was directly prepared by flow-levitation method （FL） and sintered by vacuum sintering of powder （VSP） method. Several characterizations, such as transmission electron microscopy （TEM）,...Copper-nickel nanoparticle was directly prepared by flow-levitation method （FL） and sintered by vacuum sintering of powder （VSP） method. Several characterizations, such as transmission electron microscopy （TEM）, scanning electron microscopy （SEM）, X-ray diffraction （XRD）, differential thermal analysis （DTA）, and energy-dispersive X-ray spectroscopy （EDX） were used to investigate the prepared nanostructures. The results of the study show that FL method could prepare high purity Cu-Ni nanocrystals of uniform spheres with size distribution between 20 and 90 nm. After sintering the bulk nanocrystalline copper-nickel has obvious thermal stability and the surface Webster hardness increases with the rising sintering temperature. At the temperature of 900 ℃, the specimen shows higher surface Webster hardness, which is about two times of traditional materials. When the sintering temperature arrives at 1 000 ℃ the relative density of bulk nanocrystals can reach 97.86 percent. In this paper, the variation tendency of porosity, phase and particles size of bulk along with the changing of sintering temperature have been studied.展开更多
基金supported by the National Natural Science Foundation of China(No.11176010)
文摘Bulk flow model with perturbation simplification has been used to calculate rotordynamic coefficients in annular seals which have significant influences on the dynamic behavior of rotors in turbomachinery. In this work, a transient bulk flow model with arbitrary rotor motion is developed, and the boundary conditions and friction factor in the model are calibrated with steady Computational Fluid Dynamics（CFD） analysis. The numerical solution scheme is developed based on the finite element method to obtain the transient reaction force in the seal clearance. With a periodic circular rotor orbit, the transient forces at multiple whirling frequencies are used to evaluate the rotordynamic coefficients. The leakage flowrate of CFD analysis has good agreement with experimental results and the calibrated parameters in bulk flow model are dependent on operating conditions. Although CFD calibration improves the accuracy of the perturbed bulk flow model, the direct damping is overestimated and the cross-coupled damping is underestimated. Compared with the perturbed model, the predictions of the transient bulk flow model are more agreeable with the experiment.
基金supported by the National Natural Science Foundation of China (Grant Nos. 40931054 and 41174141)National Basic Research Program of China ("973" Program) (Grant No. 2011CB811404)
文摘This paper using the dataset of BBFs (bursty bulk flows) observed by two Cluster satellites C1 and C4 studies the difference between onset times of BBFs observed by C1 and C4. It is found that the onset time differences of most of BBFs observed by C1 and C4 are smaller than 60 s. The average onset time difference of BBFs of C1 and C4 is 68.5 s. The probabilities of onset time difference of BBFs of C1 and C4 larger than 30 60 90 and 120 s are respectively 55% 35% 27% and 23%. The largest onset time difference of BBFs of C1 and C4 decreases with the increase of earthward component of maximum velocities of BBFs. The onset time difference of BBFs of C1 and C4 results from the velocity inhomogeneity inside the flow channel of BBF which may be produced in propagation path and/or in source region of BBFs. Such a wide range of onset time difference of BBFs suggests that the velocity inhomogeneity inside the flow channel of BBF is various. These results are very important to the current study of substorm research based on THEMIS data because they indicate that it is impossible to determine the onset time of BBF with a single satellite.
基金This work was financially supported by the National Natural Science Foundation of China (No.50571109, 10572142 and 10432050)the Knowledge Innovation Program of the Chinese Academy of Sciences.
文摘La57.6Al17.5(Cu,Ni)24.9 and La64Al14(Cu,Ni)22 bulk metallic glasses (BMGs) were prepared by copper-mould casting method. Plastic deformation behavior of the two BMGs at various loading rates was studied by nanoindentation. The results showed that the La57.6Al17.5(Cu,Ni)24.9 BMG with a glass transition temperature of 423 K exhibited prominent serrated flow at low loading rates, whereas less pronounced serrated flow at high rates during nanoindentation. In contrast, the La64Al14(Cu,Ni)22 BMG with a glass transition temperature of 401 K exhibited prominent serrated flow at high loading rates. The different rate dependency of serrated flow in the two La-based BMGs is related to the different glass transition temperature, and consequently the degree of viscous flow during indentation at room temperature. A smoother flow occurs in the alloy with relatively lower glass transition temperature, due to the relaxation of stress concentration.
基金supported by the National Natural Sci-ence Foundation of China under grant No. 50705092.
文摘Research results on the viscous flow deformation behavior of bulk amorphous alloy in different systems are reviewed. The material exhibits an ideal Newtonian fluid at a high temperature. Analytical solution of lamellar fluid flow behavior is used to discuss the viscous flow behavior of the bulk amorphous alloy in the supercooled liquid state. A material model, which describes such deformation behavior of Mg6oCusoYlo amorphous alloy, is introduced into the finite element method of microformin8 process. Surface feature size was investigated and found not sensitive to the micro formability. Bulk amorphous alloy may possibly be applied to microelectro-mechanical-systems （MEMS） fabrication.
基金Supported by the National Natural Science Foundation of China(No.10804101)
文摘Copper-nickel nanoparticle was directly prepared by flow-levitation method （FL） and sintered by vacuum sintering of powder （VSP） method. Several characterizations, such as transmission electron microscopy （TEM）, scanning electron microscopy （SEM）, X-ray diffraction （XRD）, differential thermal analysis （DTA）, and energy-dispersive X-ray spectroscopy （EDX） were used to investigate the prepared nanostructures. The results of the study show that FL method could prepare high purity Cu-Ni nanocrystals of uniform spheres with size distribution between 20 and 90 nm. After sintering the bulk nanocrystalline copper-nickel has obvious thermal stability and the surface Webster hardness increases with the rising sintering temperature. At the temperature of 900 ℃, the specimen shows higher surface Webster hardness, which is about two times of traditional materials. When the sintering temperature arrives at 1 000 ℃ the relative density of bulk nanocrystals can reach 97.86 percent. In this paper, the variation tendency of porosity, phase and particles size of bulk along with the changing of sintering temperature have been studied.
