Transverse pressure gradient(TPG)is one of the key factors influencing the boundary layer airflow diversion in a bump inlet.This paper proposes a novel TPG-based hypersonic bump inlet design method.This method consist...Transverse pressure gradient(TPG)is one of the key factors influencing the boundary layer airflow diversion in a bump inlet.This paper proposes a novel TPG-based hypersonic bump inlet design method.This method consists of two steps.First,a parametric optimization approach is employed to design a series of 2D inlets with various compression efficiencies.Then,according to the prescribed TPG,the optimized inlets are placed in different osculating planes to generate a 3D bump inlet.This method provides a means to directly control the aerodynamic parameters of the bump rather than the geometric parameters.By performing this method to a hypersonic chin inlet,a long and wide bump surface is formed in the compression wall,which leads to good integration of the bump/inlet.Results show that a part of the near-wall boundary layer flow is diverted by the bump,resulting in a slight decrease in the mass flow but a significant improvement in the total pressure recovery.In addition,the starting ability is significantly improved by adding the bump surface.Analysis reveals that the bump has a 3D rebuilding effect on the large-scale separation bubble of the unstarted inlet.Finally,a mass flow correction is performed on the designed bump inlet to increase the mass flow to full airflow capture.The results show that the mass flow rate of the corrected bump inlet reaches up to 0.9993,demonstrating that the correction method is effective.展开更多
There exists inlet-engine match conflict between high and low speeds for a non-adjustable bump inlet.A scheme of using a bistable bump surface at the throat region of the inlet is proposed to adjust the throat area.Th...There exists inlet-engine match conflict between high and low speeds for a non-adjustable bump inlet.A scheme of using a bistable bump surface at the throat region of the inlet is proposed to adjust the throat area.The FEM model of the bistable surface is established with hinged constraint,and the bistability condition and structural transition process are investigated in detail.Moreover,the effects of loading method,loading position and structural parameters on critical driving force,input energy and structural strain are studied.Finally,the influences of an elastic boundary condition on the structural bistability are discussed.The results show that the bistability of the adjustable bump surface requires a certain boundary constraint and geometric parameter combination,and that there are local and overall snap-through phenomena during transition which are related to the loading position and structural parameters.Therefore,suitable loading position and structural material could reduce input energy and meet the demand of structural strain.展开更多
基金the National Natural Science Foundation of China(No.12102470)the Hunan Provincial Innovation Foundation for Postgraduate(No.CX20200082),China。
文摘Transverse pressure gradient(TPG)is one of the key factors influencing the boundary layer airflow diversion in a bump inlet.This paper proposes a novel TPG-based hypersonic bump inlet design method.This method consists of two steps.First,a parametric optimization approach is employed to design a series of 2D inlets with various compression efficiencies.Then,according to the prescribed TPG,the optimized inlets are placed in different osculating planes to generate a 3D bump inlet.This method provides a means to directly control the aerodynamic parameters of the bump rather than the geometric parameters.By performing this method to a hypersonic chin inlet,a long and wide bump surface is formed in the compression wall,which leads to good integration of the bump/inlet.Results show that a part of the near-wall boundary layer flow is diverted by the bump,resulting in a slight decrease in the mass flow but a significant improvement in the total pressure recovery.In addition,the starting ability is significantly improved by adding the bump surface.Analysis reveals that the bump has a 3D rebuilding effect on the large-scale separation bubble of the unstarted inlet.Finally,a mass flow correction is performed on the designed bump inlet to increase the mass flow to full airflow capture.The results show that the mass flow rate of the corrected bump inlet reaches up to 0.9993,demonstrating that the correction method is effective.
基金supported by the National Natural Science Foundation of China(Nos.11172128,51475228)the Specialized Research Fund for the Doctoral Program of Higher Education of China (No.20123218110001)+1 种基金the Research Fund of State Key Laboratory of Mechanics and Control of Mechanics Structures (Nanjing University of Aeronautics and Astronautics)(No.0515G01)the Priority Academic Program Development of Jiangsu Higher Education Institutions and the Funding of Jiangsu Innovation Program for Graduate Education(the Fundamental Research Funds for the Central Universities)(No.CXZZ12_ 0139)
文摘There exists inlet-engine match conflict between high and low speeds for a non-adjustable bump inlet.A scheme of using a bistable bump surface at the throat region of the inlet is proposed to adjust the throat area.The FEM model of the bistable surface is established with hinged constraint,and the bistability condition and structural transition process are investigated in detail.Moreover,the effects of loading method,loading position and structural parameters on critical driving force,input energy and structural strain are studied.Finally,the influences of an elastic boundary condition on the structural bistability are discussed.The results show that the bistability of the adjustable bump surface requires a certain boundary constraint and geometric parameter combination,and that there are local and overall snap-through phenomena during transition which are related to the loading position and structural parameters.Therefore,suitable loading position and structural material could reduce input energy and meet the demand of structural strain.
