NUMERICAL SIMULATION OF TEMPERATURE FIELD ON FLASH BUTT WELDING FOR HIGH MANGANESE STEELS

An axial symmetry finite element model coupled with electricity-thermal effect was developed to study the temperature field distribution in process of the flash butt welding （FBW） of frog highmanganese steel. The influence of temperature dependent material properties and the contact resistance were taken into account in FEM ＇simulation. Meanwhile, the lost materials due to .splutter was resolved by using birth and death element. The result of analyzing data shows that the moddel in the FBW flashing is reasonable and feasible, and can exactly simulate the temperature field distribution. The modeling provides reference for analysis of welding technologies on the temperature field of high-manganese steel in FBW.

The process of electroslag pressure butt welding

Many processes are used to join reinforcing bar (steel bar), but only a few of them, e.g. overlapping welding, gas pressure welding, thread joining, cold pressure sleeve joining, are able to be used on building sites because the conditions of building sites are very particular. First, the work of joining reinforcing bar is mobile, that is to say, it must be moved from one place to another after having accomplished one joint. So it demands that the welding equipment (especially the welding head) must be convenient for moving. So it must be small and light. Second, the electricity capacity of the welding equipment can not be too large because the whole electricity capacity of a building site is limited. Third, the welding process ought to be simple because the situation og building sites is very poor and is on the open air. The more complex the process is, the more difficult the work will be. Fourth, the quality of the joint should be reliable and stable because it is impossible to check the quality of every joint, and there is no suitable way to do it even by now. For those reasons, the electroslag pressure butt welding has got great development recent years and is just suitable to be used on building sites to join vertical reinforcing bars. The article introduces its basic principle, processing, chief properties, and some test results.

Applied computer aided system for hotplate butt welding of plastics

This paper illustrates the construction and application of the applied computeraided .system for hotplate butt welding of plastics with regard to inquiry, imitation and Optimization.

Study on microstructures and properties of preheated flash butt welded SW400 steel joints

Under the spirit of sustainable development, ‘lightweight’ has been gradually included into the vehicle design criterion by many manufacturers and used in automobile production. Following this trend, domestic wheel suppliers also begin to study the technology of lightweight wheel. One way to achieve this goal is improving strength grade of the steel and optimizing the structure design in the field of steel wheels. But there are a few problems in flash butt welding process in the application of high strength steel, leading to high rejection rates. SW400 steel is a special high strength wheel steel developed by Benxi Steel. Taking SW400 steel as the research material, this article studys the feasibility of improving the properties of rim flash butt welded joints by adding preheating process.

Experimental investigation on tensile strength of butt welded joint post high temperatures

In order to investigate the laws of variation on tensile strength of butt welded joint post high temperatures, the wide plate tension tests for butt welded joint were conducted after cooling down from different high temperatures. The tests indicate that specimens appear ductile fracture at the steel plate during the tension tests after cooling down. The maximum temperatures undergone and the cooling pattern are major factors influencing tensile strength of butt welded joint post high temperatures. The tensile strength mostly reduces by 8% within 900℃. Based on the experimental results, the paper proposes the calculation formulas of tensile strength of butt welded joint post high temperatures. The conclusions of the paper supply references for evaluation damage and reinforcement of steel structure post fire.

Fatigue properties of friction stir welded butt joint and base metal of MB8 magnesium alloy

The fatigue properties of friction stir welded （FSW） butt joint and base metal of MB8 magnesium alloy were investigated. The comparative fatigue tests were carried out using EHF-EM2OOK2-070-IA fatigue testing machine for both FSW butt joint and base metal specimens. The fatigue fractures were observed and analyzed using a scanning electron microscope of JSM-6063LA type. The experimental results show that the fatigue performance of the FSW butt joint of MB8 magnesium alloy is sharply decreased. The conditional fatigue limit （2 x 106） of base metal and welded butt joint is about 77.44 MPa and 49. 91 MPa, respectively. The conditional fatigue limit （2 x 106 ） of the welded butt joint is 64.45% of that of base metal. The main reasons are that the welding can lead to stress concentration in the flash area, tensile welding residual stress in the welded joint（ The residual stress value was 30. 5 MPa）, as well as the grain size is not uniform in the heat-affected zone. The cleavage steps or quasi-cleavage patterns present on the fatigue fracture surface, the fracture type of the FSW butt joint belongs to a brittle fracture.

Improving fatigue performance of welded joints of X65 pipeline steel by UIT

Treating weld toes properly can improve the fatigue performance. Ultrasonic impact treatment （UIT） is a more effective and convenient method to enhance the fatigue strength of welded joints and suchlike structures. Fatigue tests were conducted on the specimens made of X65 pipeline steel. The test specimens were investigated on the fatigue strength and the fatigue life at the same stress range level by comparing the ones peened by UIT with the others without the treatment： the fatigue strength of the specimens as UIT, 90% of the fatigue strength of the base mental, is increased by 38% compared with that of as welded only; the fatigue life of the ones as UIT is prolonged by 11 multiples of the ones as welded only.

Residual stress characteristics of butt-welded flange by finite element analysis

Finite element simulation is utilized in an aluminum alloy 2014 butt-welded flange under AC Tungsten Inert Gas （AC-TIG） welding condition. The simulated results are in good agreement with the residual stress for the plate test using the actual welding parameters. Furthermore, characteristics of residual stress could be investigated in detail in several aspects, such as the welding structures, the welding sequences, the time intervals, preheating, and repair weld. The intermittent welding may be more convenient and advantageous for the practical applications to reduce the stress, and the local repair welding may cause more stress within the repairing region obviously.

Fabrication of widely tunable ridge waveguide DBR lasers for WDM-PON

We report the fabrication of widely tunable ridge waveguide distributed Bragg reflector （DBR） lasers with InGaAsP butt-joint as grating material. The shape of the butt-joint interface is found to have significant effect on the properties of the lasers. It is shown that irregular mode jumps during wavelength tuning can be avoided by a V-shaped butt-joint interface. From the fabricated device, 23 channels with 0.8 nm spacing and greater than 35 dB side mode suppression ratios are obtained. The different tuning characteristics of the ridge waveguide and the previously reported buried ridge stripe DBR lasers are discussed. Combined with the wide tuning range and the simple structure, the ridge waveguide DBR lasers are promising for use in wavelength division multiplexing passive optical networks （WDM-PONs）.