Interface defect induced upgrade of K-storage properties in KFeSO4Fcathode: From lowered Fe-3d orbital energy level to advancedpotassium-ion batteries

KFeSO_(4)F(KFSF)is considered a potential cathode due to the large capacity and low cost.However,the inferior electronic conductivity leads to poor electrochemical performance.Defect engineering can facilitate the electron/ion transfer by tuning electronic structure,thus providing favorable electrochemical performance.Herein,through the regulation of surface defect engineering in reduced graphene oxide(rGO),the Fe–C bonds were formed between KFSF and rGO.The Fe–C bonds formed work in regulating the Fe-3d orbital as well as promoting the migration ability of K ions and increasing the electronic conductivity of KFSF.Thus,the KFSF@rGO delivers a high capacity of 119.6 mAh g^(-1).When matched with a graphite@pitch-derived S-doped carbon anode,the full cell delivers an energy density of 250.5 Wh kg^(-1) and a capacity retention of 81.5%after 400 cycles.This work offers a simple and valid method to develop high-performance cathodes by tuning defect sites.

Degradation Mechanism of Phenol in C/PTFE O_2-Fed Cathode by Determining the Product of Oxygen Electroreduction

A terylene membrane which kept pH〉12 in cathode compartment was used to construct a divided cell with a carbon/polytetrafluoroethylene（C/PTFE） O2-fed cathode. The concentrations of hydrogen peroxide （H2O2） and hydroxyl radical （HO^-）in the catholyte were 8.3 mg/L and 2.15 μmol/L, respectivel.y, which were determined by permanganate titration, electron spin resonance （ESR） spectrum and the fluorescence spectra. ;The efficiency of the removal of phenol achieved 100% as a result of these two kinds of stronger oxidizer.

Viability of all-solid-state lithium metal battery coupled with oxide solid-state electrolyte and high-capacity cathode

Owing to the utilization of lithium metal as anode with the ultrahigh theoretical capacity density of 3860 mA h g^(-1)and oxide-based ceramic solid-state electrolytes(SE),e.g.,garnet-type Li7La_(3)Zr_(2)O_(12)(LLZO),all-state-state lithium metal batteries(ASLMBs)have been widely accepted as the promising alternatives for providing the satisfactory energy density and safety.However,its applications are still challenged by plenty of technical and scientific issues.In this contribution,the co-sintering temperature at 500℃is proved as a compromise method to fabricate the composite cathode with structural integrity and declined capacity fading of LiNi_(0.5)Co_(0.2)Mn_(0.3)O_(2)(NCM).On the other hand,it tends to form weaker grain boundary(GB)inside polycrystalline LLZO at inadequate sintering temperature for LLZO,which can induce the intergranular failure of SE during the growth of Li filament inside the unavoidable defect on the interface of SE.Therefore,increasing the strength of GB,refining the grain to 0.4μm,and precluding the interfacial defect are suggested to postpone the electro-chemo-mechanical failure of SE with weak GB.Moreover,the advanced sintering techniques to lower the co-sintering temperature for both NCM-LLZO composite cathode and LLZO SE can be posted out to realize the viability of state-of-the-art ASLMBs with higher energy density as well as the guaranteed safety.

Synthesis of nanostructured Li_2FeSiO_4/C cathode for lithium-ion battery by solution method

Nanosphere-like Li2FeSiO4/C was synthesized via a solution method using sucrose as carbon sources under a mild condition of time-saving and energy-saving, followed by sintering at high temperatures for crystallization. The amount of carbon in the composite is less than 10% （mass fraction）, and the X-ray diffraction result confirms that the sample is of pure single phase indexed with the orthorhombic Pmn21 space group. The particle size of the Li2FeSiO4/C synthesized at 700 °C for 9 h is very fine and spherical-like with a size of 200 nm. The electrochemical performance of this material, including reversible capacity, cycle number, and charge-discharge characteristics, were tested. The cell of this sample can deliver a discharge capacity of 166 mA-h/g at C/20 rate in the first three cycles. After 30 cycles, the capacity decreases to 158 mA-h/g, and the capacity retention is up to 95%. The results show that this method can prepare nanosphere-like Li2FeSiO4/C composite with good electrochemical performance.

Synthesis of porous nano/micro structured LiFePO_4/C cathode materials for lithium-ion batteries by spray-drying method

In order to enhance electrochemical properties of LiFePO4 （LFP） cathode materials, spherical porous nano/micro structured LFP/C cathode materials were synthesized by spray drying, followed by calcination. The results show that the spherical precursors with the sizes of 0.5-5 μm can be completely converted to LFP/C when the calcination temperature is higher than 500 ℃. The LFP/C microspheres obtained at calcination temperature of 700 ℃ are composed of numerous particles with sizes of -20 nm, and have well-developed interconnected pore structure and large specific surface area of 28.77 mE/g. The specific discharge capacities of the LFP/C obtained at 700 ℃ are 162.43, 154.35 and 144.03 mA.h/g at 0.5C, 1C and 2C, respectively. Meanwhile, the capacity retentions can reach up to 100% after 50 cycles. The improved electrochemical properties of the materials are ascribed to a small Li＋ diffusion resistance and special structure of LFP/C microspheres.

Synthesis and electrochemical performances of spherical LiFePO_4 cathode materials for Li-ion batteries

Spherical LiFePO4 and LiFePO4/C composite powders for lithium ion batteries were synthesized by a novel processing route of co-precipitation and subsequent calcinations in a nitrogen and hydrogen atmosphere. The precursors of LiFePO4, LiFePO4/C composite and the resultant products were characterized by X-ray diffraction (XRD), scanning electron microscope (SEM), and the electrochemical performances were investigated by galvanostatic charge and discharge tests. The precursors composed of amorphous Fe3(PO4)2·xH2O and crystalline Li3PO4 obtained in the co-precipitation processing have a sphere-like morphology. The spherical LiFePO4 derived from the calcinations of the precursor at 700 ℃ for 10 h in a reduction atmosphere shows a discharge capacity of 119 mAh·g-1 at the C/10 rate, while the LiFePO4/C composite with 10wt.% carbon addition exhibits a discharge capacity of 140 mAh·g-1. The electrochemical performances indicate that the LiFePO4/C composite has a higher specific capacity and a more stable cycling performance than the bare olivine LiFePO4 due to the carbon addition enhancing the electronic conductivity.

Synthesis and electrochemical properties of Li_(1-x)V_xCr_yFe_(1-x)PO_4/C as a cathode material

Composites Li1-xVxCryFe1-yPO4/C（x=0.01, 0.02; y = 0.01, 0.02） were synthesized by solid-state reaction method. The influence of the content of doping vanadium and chromium on the structure of Li1-xVxCryFe1-yPO4/C was investigated by XRD, while the morphology of powders was observed by SEM. The investigation of the electrochemical performances showed that the Li0.99V0.01Cr0.02Fe0.98PO4/C material has a higher capacity. At 0.1 C discharging rate, it is capable of delivering reversible specific capacity of 163.8 mAh/g with fairly stable cycleability.

An experimental study on the degradation of the C12A7 hollow cathode

Emitter overheating is by far the greatest problem limiting the performance of novel C12A7 hollow cathodes. To explore the failure operating point and degradation mechanism of the C12A7 hollow cathode, microscopic analyses of a degraded electride emitter after 10 h of thermal electron emission are presented in this paper. The morphology and composition variation of overheated electride emitters by scanning electron microscopy, energy-dispersive spectroscopy and X-ray diffraction indicate the melting and decomposition of electride of the surface layer. The monitored temperature of the electride emitter during the C12A7 hollow cathode operation shows that to avoid overheating the electride emitter, the average current density allowed should be about 64 m A mm^(-2) for the C12A7 hollow cathode in its current configuration. Experimental results of the heaterless C12A7 hollow cathode demonstrate that xenon(Xe) ion bombardment can remove the insulating layer and restore the thermionic emission capability for less degraded emitters. Based on experimental results and microscopic characterization, the depletion and degradation mechanisms of electride emitters during the hollow cathode operation are discussed.

Effect of baking processes on properties of TiB_2/C composite cathode material

Pitch and TiB2/C green composite cathode material were respectively analyzed with simultaneous DSC-TGA, and effects of three baking processes of TiB2/C composite cathode material, i.e. K25, K5 and M5, on properties of TiB2/C composite cathode material were investigated. The results show that thermogravimetrie behavior of pitch and TiB2/C green composite cathode is similar, and appears the largest mass loss rate in the temperature range from 200 to 600 ℃. The bulk density variation of sample K5 before and after baking is the largest （11.9%）, that of sample K25 is the second, and that of sample M5 is the smallest （6.7%）. The crushing strength of sample M5 is the biggest （51.2 MPa）, that of sample K2.5 is the next, and that of sample K5 is the smallest （32.8 MPa）. But, the orders of the electrical resistivity and electrolysis expansion of samples are just opposite with the order of crushing strength. The heating rate has a great impact on the microstructure of sample. The faster the heating rate is, the bigger the pore size and porosity of sample are. Compared with the heating rate between 200 and 600℃ of samples K25 and K5, that of sample M5 is slower and suitable for baking process of TiB2/C composite cathode material.

Inverted Organic Solar Cells with Improved Performance using Varied Cathode Buffer Layers

Organic solar cells with inverted planar heterojunction structure based on subphthalocya- nine and C60 were fabricated using several kinds of materials as cathode buffer layer （CBL）, including tris-8-hydroxy-quinolinato aluminum （Alq3）, bathophenanthroline （Bphen）, bathocuproine, 2,3,8,9,14,15-hexakis-dodecyl-sulfanyl-5,6,11,12,17,18-hexaazatrinaphthylene （HATNA）, and an inorganic compound of Cs2CO3. The influence of the lowest unoccupied molecular orbital level and the electron mobility of organic CBL on the solar cells perfor- mance was compared. The results showed that Alq3, Bphen, and HATNA could significantly improve the device performance. The highest efficiency was obtained from device with an- nealed HATNA as CBL and increased for more than 7 times compared with device without CBL. Furthermore~ the simulation results with space charge-limited current theory indicated that the Schottky barrier at the organic/electrode interface in inverted OSC structure was reduced for 27% by inserting HATNA CBL.

Hydrothermal synthesis of spindle-like Li_2FeSiO_4-C composite as cathode materials for lithium-ion batteries

In this paper,we report on the preparation of Li2FeSiO4,sintered Li2FeSiO4,and Li2FeSiO4-C composite with spindle-like morphologies and their application as cathode materials of lithium-ion batteries.Spindle-like Li2FeSi04 was synthesized by a facile hydrothermal method with（NH4）2Fe（SO4）2 as the iron source.The spindle-like Li2FeSiO4 was sintered at 600 ℃ for 6 h in Ar atmosphere.Li2FeSiO4-C composite was obtained by the hydrothermal treatment of spindle-like Li2FeSiO4 in glucose solution at 190 ℃ for 3 h.Electrochemical measurements show that after carbon coating,the electrode performances such as discharge capacity and high-rate capability are greatly enhanced.In particular.Li2FeSiO4-C with carbon content of 7.21 wt%delivers the discharge capacities of 160.9 mAh·g-1 at room temperature and 213 mAh·g-1 at45℃（0.1 C）,revealing the potential application in lithium-ion batteries.

Micro–meso-macroporous FeCo-N-C derived from hierarchical bimetallic FeCo-ZIFs as cathode catalysts for enhanced Li-O2 batteries performance

Developing bifunctional catalysts that increase both the OER and ORR kinetics and transport reactants with high efficiency is desirable. Herein, micro–meso-macroporous FeCo-N-C-X(denoted as "MFeCo-N-C-X", X represents Fe/Co molar ratio in bimetallic zeolite imidazole frameworks FeCo-ZIFs) catalysts derived from hierarchical M-FeCo-ZIFs-X was prepared. The micropores in M-FeCo-N-C-X have strong capability in O2 capture as well as dictate the nucleation and early-stage deposition of Li2O2,the mesopores provided a channel for the electrolyte wetting, and the macroporous structure promoted more available active sites when used as cathode for Li-O2 batteries. More importantly, M-Fe CoN-C-0.2 based cathode showed a high initial capacity(18,750 mAh g-1@0.1 A g-1), good rate capability(7900 m Ah g-1@0.5 A g-1), and cycle stability up to 192 cycles. Interestingly, the FeCo-N-C-0.2 without macropores suffered relatively poorer stability with only 75 cycles, although its discharge capacity was still as high as 17,200 mA h g-1(@0.1 A g-1). The excellent performance attributed to the synergistic contribution of homogeneous Fe, Co nanoparticles and N co-doping carbon frameworks with special micro–meso-macroporous structure. The results showed that hierarchical FeCo-N-C architectures are promising cathode catalysts for Li-O2 batteries.

Cathode Erosion of Graphite and Cu/C Materials in Airarcs

Cathode erosion of graphite and Cu/C was studied in direct current arcs, which were ignited between two electrodes comprised of two kinds of carbon materials and a tungsten anode in air. The arced zones on the cathode surface were investigated by a scanning electron microscope. Also, the cathode erosion rates of the investigated materials were measured. The results show that two distinct zone can be seen on both cathodes. The eroded area was located at the zone just opposite to the anode and surrounded by a white zone. The arced surface on the Cu/C containing 9.3 % Cu is rougher than that of the pure graphite. Many particles with various sizes distributed on the Cu/C. The vaporization of Cu can lower the surface temperature and reduce the cathode erosion. Therefore, the cathode erosion rate of the Cu/C is lower than that of the pure graphite.

Early experimental investigation of the C12A7 hollow cathode fed on iodine

To fully realize the superiority of the iodine electric propulsion system in streamlining the size and reducing the operating costs, iodine hollow cathode technology must be developed. Considering the corrosiveness of iodine and the possible impurity of the working propellant, the C12A7 hollow cathode with promising chemical ability was developed and tested. The C12A7 hollow cathode with a nominal current of 1–4 A was successfully ignited with iodine from the reservoir outside the vacuum chamber. It was operated at 1 A of anode current with a 1.2 mg s^(-1) iodine mass flow rate.Despite involuntary extinguishment, the C12A7 hollow cathode could be restarted repeatedly with a single operation time of up to 12 min and a total duration of 30 min. The unexpected fluctuation of iodine flow may be the reason for the short operation time. Experimental results and microscopical observation of the electride emitter show the compatibility of the iodine and electride emitter. For the development and demonstration of future single-iodine electric propulsion of Hall thrusters, the iodine storage and supply system with precise control and regulation may be the critical technology.

CoSnO_(3)/C nanocubes with oxygen vacancy as high-capacity cathode materials for rechargeable aluminum batteries

Rechargeable aluminum batteries(RABs)are attractive cadidates for next-generation energy storage and conversion,due to the low cost and high safety of Al resources,and high capacity of metal Al based on the three-electrons reaction mechanism.However,the development of RABs is greatly limited,because of the lack of advanced cathode materials,and their complicated and unclear reaction mechanisms.Exploring the novel nanostructured transition metal and carbon composites is an effective route for obtaining ideal cathode materials.In this work,we synthesize porous CoSnO_(3)/C nanocubes with oxygen vacancies for utilizing as cathodes in RABs for the first time.The intrinsic structure stability of the mixed metal cations and carbon coating can improve the cycling performance of cathodes by regulating the internal strains of the electrodes during volume expansion.The nanocubes with porous structures contribute to fast mass transportation which improves the rate capability.In addition to this,abundant oxygen vacancies promote the adsorption affinity of cathodes,which improves storage capacity.As a result,the CoSnO_(3)/C cathodes display an excellent reversible capacity of 292.1 mAh g^(-1) at 0.1 A g^(-1),a good rate performance with 109 mAh g^(-1) that is maintained even at 1 A g^(-1) and the provided stable cycling behavior for 500 cycles.Besides,a mechanism of intercalation of Al^(3+)within CoSnO_(3)/C cathode is proposed for the electrochemical process.Overall,this work provides a step toward the development of advanced cathode materials for RABs by engineering novel nanostructured mixed transition-metal oxides with carbon composite and proposes novel insights into chemistry for RABs.

Synthesis and electrochemical performance of Li_2Mg_(0.15)Mn_(0.4)Co_(0.45)SiO_4/C cathode material for lithium ion batteries

The synthesis, structure and performance of Li2Mg0.15Mn0.4Co0.45SiO4/C cathode material were studied. The Li2Mg0.15Mn0.4Co0.45SiO4/C solid solution with orthorhombic unit cell （space group Pmn21） was synthesized successfully by combination of wet process and solid-state reaction at high temperature, and its electrochemical performance was investigated primarily. Li2Mg0.15Mn0.4Co0.45SiO4/C composite materials deliver a charge capacity of 302 mA-h/g and a discharge capacity of 171 mA.h/g in the first cycle. The discharge capacity is stabilized at about 100 mA-h/g after 10 cycles at a current density of 10 mA/g in the voltage of 1.5-4.8 V vs Li/Li^＋. The results show that Mg-substitution for the Co ions in Li2Mn0.4Co0.6SiO4 improves the stabilization of initial structure and the electrochemical nerformance.

PTFE含量对Pt/C/PTFE疏水催化剂氢水液相催化交换性能的影响

研究采用液相还原法制备10%Pt/C催化剂,再将其与PTFE一起负载于多孔金属载体,制备Pt/ C/PTFE疏水催化剂。用XRD表征Pt/C催化剂上Pt晶相结构和粒径大小,Pt粒子平均粒径为3.1nm;SEM表征PTFE与Pt/C催化剂的分散状态,二者基本混合均匀,局部地方有因未均匀分散而形成的PTFE膜。由于催化剂疏水性不够,PTFE与Pt/C质量比为0.5∶1时,Pt/C/PTFE催化剂活性较低,比例增至1∶1,催化剂活性明显增加,而继续增加PTFE比例,有更多的Pt活性位被包覆在PTFE中,同时催化剂内扩散效应增加,催化剂活性又逐渐降低。对多孔金属载体预处理,PTFE与Pt/C质量比为0.5∶1时,Pt/C/PTFE催化剂活性增加,而比例升为1∶1时,催化剂活性降低。

碱性燃料电池产过氧化氢阴极C/PTFE的制备及性能表征

研究了碱性燃料电池合成过氧化氢阴极碳/聚四氟乙烯(C/PTFE)的制备方法,考察了制备过程中的主要影响因素,并通过伏安曲线和过氧化氢浓度曲线及交流阻抗图谱,对不同条件下制备的阴极性能进行了评价.结果表明,压力、整平层碳含量及聚四氟乙烯含量对阴极性能均有较大影响,其中压力为10.0MPa、碳含量为0.2g及聚四氟乙烯含量为50%条件下制备的阴极能获得最大电流,过氧化氢的产量最高,2.5h后过氧化氢浓度达到56mmol/L。

C_(18)与PTFE表面收集Cd(OH)_2沉淀的比较研究及电热原子吸收光谱法测定痕量镉

C18表面被证实可有效收集Cd(OH)2沉淀。本研究比较了阀上实验室中C18微填充柱与顺序注射系统中PTFE-KR(polytetrafluorothylene-knotted reactor)编结反应器收集Cd(OH)2沉淀的性能。以NaOH为沉淀剂,在线生成的沉淀吸附在C18表面或PTFE-KR内表面而与基体分离。沉淀经HNO3洗脱后用电热原子吸收测定。当进样量为600(L时,以C18微柱和PTFE-KR为收集媒介,测得的富集系数、吸附效率(%)、精密度(%,0.05μg/L)、进样频率和检出限(ng/L)依次分别为28/14、93/48、2.1/4.7、13/20和1.7/3。测定了3种标准样品中的痕量镉,所得结果与标准值相符。

C/PTFE和PbO_2电极同时作用氧化降解甲基橙废水实验研究

以电还原氧气产生H_2O_2的C/PTFE气体扩散电极为阴极,PbO_2电极作为阳极,涤纶滤膜作为隔膜,采用阴阳极同时作用氧化降解甲基橙模拟废水,实验考察了曝气量、电流密度及初始pH值对甲基橙降解效果的影响。结果表明:在pH值为7,电流密度30mA/cm^2,曝气量1.2L/min,电解时间80min时,脱色率可以达到90%以上,脱色效果阳极室好于阴极室;COD去除率可达到85%以上,阴极室COD去除率高于阳极室。