The non-destructive testing of brazed joint in honeycomb structure with thin panel （ thickness ： 0. 2 mm） was studied by ultrasonic C-scan method. Samples with different types of artificial defect were designed; th...The non-destructive testing of brazed joint in honeycomb structure with thin panel （ thickness ： 0. 2 mm） was studied by ultrasonic C-scan method. Samples with different types of artificial defect were designed; the characteristic signal and the main parameters of the test were determined by the pre-experiment, and then parameters were optimized by orthogonal design, finally the optimum process was verified by a single panel sample. The multiple reflection echoes were chosen as the characteristic signal. The optimal C-scan results were achieved when the 20 MHz focus probe was used, and the pass band range for received signal were selected as 8 - 17. 5 MHz. The defects such as incomplete penetration and core damage can be detected with ultrasonic C-scan, and the detection accuracy can reach to 1 ram.展开更多
In this paper, ultrasonic C-scan test of spot welds for stainless steel has been studied. It is concluded that large scanning step length contributes to high testing efficiency, however, the low-resolution C-scan imag...In this paper, ultrasonic C-scan test of spot welds for stainless steel has been studied. It is concluded that large scanning step length contributes to high testing efficiency, however, the low-resolution C-scan image generated cannot be used to assess spot welding quality reliably. Based on bicubic image interpolation, the C-scan image in low resolution with the large step length 1 000 ~xm is subdivided and reconstructed. By this means, the C-scan image resolution is greatly enhanced and testing results obtained are satisfactory, realizing rapid assessment of spot welds. The results of rapid ultrasonic C-scan test fit the actual metallographic measured value well. Mean value of normal distribution of error statistics is O. 006 67, and the standard deviation is O. 087 11. Rapid ultrasonic C-scan test based on image interpolation is of high accuracy and excellent stability.展开更多
A focused ultrasonic transducer is used for precise, step-by-step, surface ultrasonic svanuing iusgection of spot welds. Two methods for generating characteristic data matrices of ultrasonic echo signals of the spot w...A focused ultrasonic transducer is used for precise, step-by-step, surface ultrasonic svanuing iusgection of spot welds. Two methods for generating characteristic data matrices of ultrasonic echo signals of the spot welds are established. One is based on the ultrasonic echo amplitude and the other is based on frequency spectrum. Both methods generate scamping inspection data arrays and provide clear C-scan images. Based on C-scan noise reduction, the Krisch edge detection operator for edge detection-a gray window transform-reflects the shapes of the spot welds and allows quantitative determination of their size. The method based on the ultrasonic echo amplitude provides a greater quantitative detection accuracy.展开更多
Crack detection in an aerospace turbine disk is essential for aircraft-quality detection.With the unique circular stepped structure and superalloy material properties of aerospace turbine disk,it is difficult for the ...Crack detection in an aerospace turbine disk is essential for aircraft-quality detection.With the unique circular stepped structure and superalloy material properties of aerospace turbine disk,it is difficult for the traditional ultrasonic testing method to perform efficient and accurate testing.In this study,ultrasound phased array detection technology was applied to the non-destructive testing of aviation turbine disks:(i)A phased array ultrasonic c-scan device for detecting aerospace turbine disk cracks(PAUDA)was developed which consists of phased array ultrasonic,transducers,a computer,a displacement encoder,and a rotating scanner;(ii)The influence of the detection parameters include frequency,wave-type,and elements number of the ultrasonic phased array probe on the detection results on the near-surface and the far surface of the aerospace turbine disk is analyzed;(iii)Specimens with flat-bottom-hole(FBH)defects were scanned by the developed PAUDA and the results were analyzed and compared with the conventional single probe ultrasonic water immersion testing.The experiment shows that by using the ultrasonic phased array c-scan to scan the turbine disk the accuracy of the detection can be significantly improved which is of greater accuracy and higher efficiency than traditional immersion testing.展开更多
文摘The non-destructive testing of brazed joint in honeycomb structure with thin panel （ thickness ： 0. 2 mm） was studied by ultrasonic C-scan method. Samples with different types of artificial defect were designed; the characteristic signal and the main parameters of the test were determined by the pre-experiment, and then parameters were optimized by orthogonal design, finally the optimum process was verified by a single panel sample. The multiple reflection echoes were chosen as the characteristic signal. The optimal C-scan results were achieved when the 20 MHz focus probe was used, and the pass band range for received signal were selected as 8 - 17. 5 MHz. The defects such as incomplete penetration and core damage can be detected with ultrasonic C-scan, and the detection accuracy can reach to 1 ram.
文摘In this paper, ultrasonic C-scan test of spot welds for stainless steel has been studied. It is concluded that large scanning step length contributes to high testing efficiency, however, the low-resolution C-scan image generated cannot be used to assess spot welding quality reliably. Based on bicubic image interpolation, the C-scan image in low resolution with the large step length 1 000 ~xm is subdivided and reconstructed. By this means, the C-scan image resolution is greatly enhanced and testing results obtained are satisfactory, realizing rapid assessment of spot welds. The results of rapid ultrasonic C-scan test fit the actual metallographic measured value well. Mean value of normal distribution of error statistics is O. 006 67, and the standard deviation is O. 087 11. Rapid ultrasonic C-scan test based on image interpolation is of high accuracy and excellent stability.
文摘A focused ultrasonic transducer is used for precise, step-by-step, surface ultrasonic svanuing iusgection of spot welds. Two methods for generating characteristic data matrices of ultrasonic echo signals of the spot welds are established. One is based on the ultrasonic echo amplitude and the other is based on frequency spectrum. Both methods generate scamping inspection data arrays and provide clear C-scan images. Based on C-scan noise reduction, the Krisch edge detection operator for edge detection-a gray window transform-reflects the shapes of the spot welds and allows quantitative determination of their size. The method based on the ultrasonic echo amplitude provides a greater quantitative detection accuracy.
基金This work was funded by the National Natural Science Foundation of China[Grant Nos.11664027,11374134]The National Natural Science Foundation of Jiangxi Province[Grant No.20161BAB216101]+1 种基金Key Laboratory of Non-Destructive Testing and Monitoring Technology for High-Speed Transport Facilities of the Ministry of Industry and Information Technology,Nanjing University of Aeronautics and AstronauticsThe Key Laboratory of Nondestructive Testing of Ministry of Education Nanchang Hang Kong University,Nanchang,China.
文摘Crack detection in an aerospace turbine disk is essential for aircraft-quality detection.With the unique circular stepped structure and superalloy material properties of aerospace turbine disk,it is difficult for the traditional ultrasonic testing method to perform efficient and accurate testing.In this study,ultrasound phased array detection technology was applied to the non-destructive testing of aviation turbine disks:(i)A phased array ultrasonic c-scan device for detecting aerospace turbine disk cracks(PAUDA)was developed which consists of phased array ultrasonic,transducers,a computer,a displacement encoder,and a rotating scanner;(ii)The influence of the detection parameters include frequency,wave-type,and elements number of the ultrasonic phased array probe on the detection results on the near-surface and the far surface of the aerospace turbine disk is analyzed;(iii)Specimens with flat-bottom-hole(FBH)defects were scanned by the developed PAUDA and the results were analyzed and compared with the conventional single probe ultrasonic water immersion testing.The experiment shows that by using the ultrasonic phased array c-scan to scan the turbine disk the accuracy of the detection can be significantly improved which is of greater accuracy and higher efficiency than traditional immersion testing.
