Effect of casting process on the inner-wall band segregation of high-strength antisulfur pipes

Controlling inner-wall band segregation is one of the difficulties in the production of high-strength antisulfur pipes.Comparative tests were carried out on different casting processes(superheat,mold electromagnetic stirring,end electromagnetic stirring,casting speed and soft reduction)for the smelting of high-strength antisulfur pipes.The microstructures of continuous-casting billets and hot-rolled or tempered pipes were analyzed using a metallographic microscope and scanning electron microscope.The mechanism and evolution law regarding the inner-wall band segregation of high-strength antisulfur pipes were studied,and the influence of different casting processes was explored.

Data-driven casting defect prediction model for sand casting based on random forest classification algorithm

The complex sand-casting process combined with the interactions between process parameters makes it difficult to control the casting quality,resulting in a high scrap rate.A strategy based on a data-driven model was proposed to reduce casting defects and improve production efficiency,which includes the random forest(RF)classification model,the feature importance analysis,and the process parameters optimization with Monte Carlo simulation.The collected data includes four types of defects and corresponding process parameters were used to construct the RF model.Classification results show a recall rate above 90% for all categories.The Gini Index was used to assess the importance of the process parameters in the formation of various defects in the RF model.Finally,the classification model was applied to different production conditions for quality prediction.In the case of process parameters optimization for gas porosity defects,this model serves as an experimental process in the Monte Carlo method to estimate a better temperature distribution.The prediction model,when applied to the factory,greatly improved the efficiency of defect detection.Results show that the scrap rate decreased from 10.16% to 6.68%.

Study on Numerical Simulation of Mold Filling and Heat Transfer in Die Casting Process

A 3-D mathematical model considering turbulence phenomena has been established based on a computational fluid dynamics technique, so called 3-D SOLA-VOF (Solution Algorithm-Volume of Fluid), to simulate the fluid flow of mold filling process of die casting. In addition, the mathematical model for simulating the heat transfer in die casting process has also been established. The computation program has been developed by the authors with the finite difference method (FDM) recently. As verification, the mold filling process of a S-shaped die casting has been simulated and the simulation results coincide with that of the benchmark test. Finally, as a practical application, the gating design of a motorcycle component was modified by the mold filling simulation and the dies design of another motorcycle component was optimized by the heat transfer simulation. All the optimized designs were verified by the production practice.

Effect of melting temperature on microstructural evolutions, behavior and corrosion morphology of Hadfield austenitic manganese steel in the casting process

In this study, the effect of melting temperature on the microstructural evolutions, behavior, and corrosion morphology of Hadfield steel in the casting process is investigated. The mold was prepared by the sodium silicate/CO_2 method, using a blind riser, and then the desired molten steel was obtained using a coreless induction furnace. The casting was performed at melting temperatures of 1350, 1400, 1450, and 1500°C, and the cast blocks were immediately quenched in water. Optical microscopy was used to analyze the microstructure, and scanning electron microscopy(SEM) and X-ray diffractrometry(XRD) were used to analyze the corrosion morphology and phase formation in the microstructure, respectively. The corrosion behavior of the samples was analyzed using a potentiodynamic polarization test and electrochemical impedance spectroscopy(EIS) in 3.5 wt% NaCl. The optical microscopy observations and XRD patterns show that the increase in melting temperature led to a decrease of carbides and an increase in the austenite grain size in the Hadfield steel microstructure. The corrosion tests results show that with increasing melting temperature in the casting process, Hadfield steel shows a higher corrosion resistance. The SEM images of the corrosion morphologies show that the reduction of melting temperature in the Hadfield steel casting process induced micro-galvanic corrosion conditions.

Microstructure and mechanical properties of AZ91-Ca magnesium alloy cast by different processes

The microstructure and mechanical properties of magnesium(Mg) alloys are significantly influenced by the casting process. In this paper, a comparative study on microstructure and mechanical properties at ambient and elevated temperatures of AZ91-2 wt.% Ca(AZX912) Mg alloy samples prepared by gravity casting(GC), squeeze casting(SC) and rheo-squeeze casting(RSC), respectively, was carried out. The results show that α-Mg grains in SC and RSC samples are significantly refined compared to the GC sample. The average secondary dendritic arm spacing of AZX912 alloy samples decreases in the order of GC, SC and RSC. As testing temperature increases from 25 °C to 200 °C, strength of AZX912 alloy samples is reduced, while their elongation is increased continuously. Compared to GC and SC processes, RSC process can improve the mechanical properties of AZX912 alloy at both ambient and elevated temperatures. The enhancement of mechanical properties of RSC sample over GC and SC samples mainly results from grain refinement in the as-cast microstructure of AZX912 alloy.

基于AnyCasting的磨辊辊皮铸造模拟与工艺优化

针对磨辊辊皮铸造过程中易出现缩孔等缺陷问题,运用AnyCasting软件对其充型、凝固过程进行模拟。首先,分析铸件金属液的凝固规律,预测缩孔缺陷产生的部位;其次,通过在型腔底部下方增设冷铁,对初始铸造工艺进行优化。结果表明,上移缩孔在冒口中的位置可有效防止在铸件上发生缩孔。按此工艺生产的辊皮铸件无缩孔、组织致密且硬度高。

Optimization of casting process based on the theory of inventive problem solving

Optimization of casting process involves the adjustment of parameters as well as the improvement of process schemes and measures.This paper proposes a new method based on the Theory of Inventive Problem Solving(TRIZ) for casting process optimization,and realizes the idea of applying TRIZ to optimize the casting process of a magnesium alloy intake manifold.By this method,the casting process is optimized so as to remove the shrinkage pores.The successful optimization of casting process demonstrates the feasibility of the proposed method.

Finite element analysis for die casting parameters in high-pressure die casting process

The gating system and the overflow system were designed according to the casting structure during high pressure die casting(HPDC) process. The simulation was carried out by ProCAST software to visualize the injection chamber pre-crystallization and the flow of molten metal. The main work is to research four die casting process parameters, i.e. injection temperature, low-pressure velocity, high-and low-pressure velocity’s switching position, and high-pressure velocity. Experimental results show that the higher injection temperature and lowpressure velocity can mitigate the pre-crystallization of the injection chamber. However, when the low-pressure velocity exceeds 0.2 m·s-1, the air entrapment in the chamber occurs. Besides, when the high-pressure velocity is greater than 2.5 m·s-1, the overflow channel at the final filling position is covered by the liquid metal too early. Finally, the injection temperature of 650 °C, the low-pressure velocity of 0.2 m·s-1, the high-and low-pressure velocity’s switching position of 320 mm and the high-pressure velocity of 2 m·s-1 are obtained as the optimal parameters by the software simulation, which has been verified by actual production.

Novel methodology for casting process optimization using Gaussian process regression and genetic algorithm

High pressure die casting (HPDC) is a versatile material processing method for mass-production of metal parts with complex geometries,and this method has been widely used in manufacturing various products of excellent dimensional accuracy and productivity. In order to ensure the quality of the components,a number of variables need to be properly set. A novel methodology for high pressure die casting process optimization was developed,validated and applied to selection of optimal parameters,which incorporate design of experiment (DOE),Gaussian process (GP) regression technique and genetic algorithms (GA). This new approach was applied to process optimization for cast magnesium alloy notebook shell. After being trained,using data generated by PROCAST (FEM-based simulation software),the GP model approximated well with the simulation by extracting useful information from the simulation results. With the help of MATLAB,the GP/GA based approach has achieved the optimum solution of die casting process condition settings.

Microstructural characteristics and mechanical properties of bronze/steel bimetallic laminated composite prepared by protective atmosphere casting process

The bonding quality of bronze/steel bimetallic laminated composite is the key factor to whether it can be used in poor working conditions.In this study,bimetallic billets were prepared by the protective atmosphere casting process.The microstructural characteristics,mechanical properties and interface bonding mechanism of the bronze/steel bimetallic composites were analyzed comprehensively through a series of microstructure analysis(inicluding OM,SEM,and EDS)and mechanical properties tests.The experimental results demonstrate that the vaporization of lead(Pb)element in the bronze is only 0.4%in weight,and alloy elements are diffused into both sides at the interface.Moreover,the hardness in the bronze region exceeds 100.0 HV which indicates excellent wear resistance.Tensile and shear tests indicate that the fractures mainly occur on the bronze side with the interaction of the brittle fracture of Pb particles and the ductile fracture of Cu-Sn solid solution.The maximum tensile strength and shear strength reach 204.0 MPa and 211.0 MPa,respectively.These results demonstrate that the protective atmosphere casting process is applicable for the preparation of bronze/steel bimetallic laminated composite with high quality.

Development of vacuum die-casting process

The vacuum die-casting process,started 25 years ago in Japan,has been widely applied.This technology contributes very much to improvement of castings quality.The main factor causing the defects of die castings is the trapped air in the mold cavity,while the key technology of vacuum die-casting process is to avoid the trapped air effectively by evacuating the cavity before casting.At the same time,due to the shot speed and the casting pressure reduced in half,the service life of the die is prolonged and the productivity is enhanced,as well.Vacuum die-casting process is of great signif icance in improving the die castings quality and making up the shortcomings of super-high-speed shot casting.

NUMERICAL SIMULATION OF CASTING'S MOLD FILLING PROCESS

Numerical simulation of casting＇s mold filling process is the main and the most important aspect of the foundry CAE technology. But it is time-consuming; it may take dozens of hours or several days. While with the development of computer hardware, numerical simulation of casting＇ s mold filling process has made rapid progress. The simulation results, therefore, have become more and more practical. This study tries to find some clues of the computational time of mold filling process. Firstly, this paper introduces mathematic model and the basic route of numerical simulation of casting＇s mold filling process. Then the computational time of mold filling process has been carefully studied, and some new and useful results have been gained from the study of the computational time. Finally, this paper has given some real applications of numerical simulation of casting＇s mold filling process.

Effect of Process Factors on Microstructure of Semisolid Continuous Casting Billets

Semisolid continuous casting (SSCC) is a new technology to produce billets for semisolid metal forming (SSMF). The effect of process factors, such as pouring temperature, stirring rate, preheating temperature and thermal conductivity of stirring chamber, on the microstructure of SSCC billets was studied by means of the factorial experimental method. The results show that the microstructure of SSCC billets can be controlled by the above-mentioned four process factors. In order to obtain fine and rounded granular grains in an SSCC billet, the pouring temperature, preheating temperature and stirring rate should be kept in a moderate range, and the thermal conductivity of stirring chamber should be high. The regression equations with the process factors connecting the microstructure was also set up based on experimental data.

Optimization of processing parameters for rheo-casting AZ91D magnesium alloy

A design of experiment technique was used to optimize the microstructure of the AZ91D alloy produced by rheo-casting. The experimental design consists of four parameters(pouring temperature,shearing temperature,shearing time and shearing rate) with three levels.The grain size and shape factor measurements of primaryα-Mg particles were conducted to determine the microstructure.The contribution of each parameter shows that pouring temperature is the most significant parameter affecting the grain size,and the shape factor highly depends on the shearing temperature.The optimized rheo-casting processing parameters are 650 C for pouring temperature,585℃for shearing temperature,40 s for shearing time,and 600 r/min for shearing rate.Under the optimized processing parameters,the average grain size is 28.53μm,and the shape factor is 0.591.

Effect of process parameters on density of magnesium alloy parts by low-pressure expendable pattern casting

The combination of magnesium alloys with the low-pressure expendable pattern casting(LP-EPC) process would bright future for application of magnesium alloys. The researches are focused on the effect of process parameters on the internal casting quality of magnesium alloy parts. AZ91D magnesium alloy castings were produced for different combinations of the LP-EPC process parameters. Specifically,pouring temperature,vacuum,filling velocity and coupling action of these factors were manipulated to observe their effect on the casting porosity and density distribution. The results indicate that the pouring temperature with LP-EPC process is lower than it in gravity casting. The selected process parameters,such as vacuum,filling velocity and coupled modes of them,must ensure melt metal flowing front profile exhibiting smooth and convex shape. The optimal process parameters for the castings are pouring temperature 983-1 023 K,vacuum 0.02-0.03 MPa,filling velocity 60-95 mm/s,and simultaneous filling with sucking.

Effect of Processing Paramters on Metal Matrix Composites: Stir Casting Process

Conventional stir casting process has been employed for producing discontinuous particle reinforced metal matrix composites for decades. The major problem of this process is to obtain sufficient wetting of particle by liquid metal and to get a homogenous dispersion of the ceramic particles. In the present study, aluminium metal matrix composites were fabricated by different processing temperatures with different holding time to understand the influence of process parameters on the distribution of particle in the matrix and the resultant mechanical properties. The distribution is examined by microstructure analysis, hardness distribution and density distribution.

Research on the Casting-forging Precision Forming Process of Alternator Poles

The casting-forging combined technique and the closed die forging without flash-less are both new developed material working methods. The former can not only decrease forming operations of forgings, but also increase the material utilization ratio. Therefore, it is applied to produce more complex forgings. The latter is required for forging precise parts without burrs. The alternator pole is a complex forging, which was usually produced by hot forging, upsetting-extrusion or upsetting-extrusion and bending processes. During these processes, not only the forming force is higher, but the material of burrs accounts for 30 percent or so of total required material. And burrs are difficult to remove in the sequential machining process. In accordance with defects exiting in current manufacturing of alternator poles by upsetting-extruding process, such as more material demand, higher forming force and difficulty of next machining, a casting-forging precision process of alternator poles was developed and investigated in this paper. In the process, the pole was formed by two operations. One is the pre-forming operation by casting. The other is the final forming operation by the closed precision forging process. This can not only shorten processes, decrease material and power demand, but also increase precision of forgings. First, the casting blocker was designed considering the casting process and the forging ratio and the mode of deformation. Then the die structure for closed precision forging was designed, and the closing device for forging dies with spring assemblies in order to provide the necessary closing force was also designed. Finally the forming processes was investigated by test and numerical simulation method to optimum process parameters and die structure design parameters. The result can provide basis for applying the process to manufacture poles in practice.

Development of 2D casting process CAD system based on PDF/image files

A casting process CAD is put forward to design and draw casting process. The 2D casting process CAD, most of the current systems are developed based on one certain version of the AutoCAD system. However the application of these 2D casting process CAD systems in foundry enterprises are restricted because they have several deficiencies, such as being overly dependent on the AutoCAD system, and some part files based on PDF format can not be opened directly. To overcome these deficiencies, for the first time an innovative 2D casting process CAD system based on PDF and image format file has been proposed, which breaks through the traditional research and application notion of the 2D casting process CAD system based on AutoCAD. Several key technologies of this system such as coordinate transformation, CAD interactive drawing, file storage, PDF and image format files display, and image recognition technologies were described in detail. A practical 2D CAD casting process system named HZCAD2D(PDF) was developed, which is capable of designing and drawing the casting process on the part drawing based on the PDF format directly, without spending time on drawing the part produced by AutoCAD system. Finally, taking two actual castings as examples, the casting processes were drawn using this system, demonstrating that this system can significantly shorten the cycle of casting process designing.

Heat Transfer between Casting and Die during High Pressure Die Casting Process of AM50 Alloy-Modeling and Experimental Results

A method based on die casting experiments and mathematic modeling is presented for the determination of the heat flow density （HFD） and interfacial heat transfer coefficient （IHTC） during the high pressure die casting （HPDC） process.Experiments were carried out using step shape casting and a commercial magnesium alloy,AM50.Temperature profiles were measured and recorded using thermocouples embedded inside the die. Based on these temperature readings,the HFD and IHTC were successfully determined and the calculation results show that the HFD and IHTC at the metal-die interface increases sharply right after the fast phase injection process until approaching their maximum values,after which their values decrease to a much lower level until the dies are opened.Different patterns of heat transfer behavior were found between the die and the casting at different thicknesses.The thinner the casting was,the more quickly the HFD and IHTC reached their steady states.Also,the values for both the HFD and IHTC values were different between die and casting at different thicknesses.

Virtual Mold Technique in Thermal Stress Analysis during Casting Process

It is important to analyse the casting product and the mold at the same time considering thermal contraction of the casting and thermal expansion of the mold. The analysis considering contact of the casting and the mold induces the precise prediction of stress distribution and the defect such as hot tearing. But it is difficult to generate FEM mesh for the interface of the casting and the mold. Moreover the mesh for the mold domain spends lots of computational time and memory for the analysis due to a number of meshes. Consequently we proposed the virtual mold technique which only uses mesh of the casting part for thermal stress analysis in casting process. The spring bar element in virtual mold technique is used to consider the contact of the casting and the mold. In general, a volume of the mold is much bigger than that of casting part, so the proposed technique decreases the number of mesh and saves the computational memory and time greatly. In this study, the proposed technique was verified by the comparison with the traditional contact technique on a specimen. And the proposed technique gave satisfactory results.