Preparation of α-Bi_2O_3 from bismuth powders through low-temperature oxidation

α-Bi2O3 powders were prepared from nanometer Bi powders through low-temperature oxidation at less than 873.15 K. XRD, SEM, TEM and HRTEM were used to characterize the structure and morphology of Bi powders and Bi2O3 particles. Kinetic studies on the bismuth oxidation at low-temperatures were carried out by TGA method. The results show that bismuth beads should be reunited and oxidized to become irregular Bi2O3 powders. The bismuth oxidation follows shrinking core model, and its controlling mechanism varies at different reaction time. Within 0-10 min, the kinetics is controlled by chemical reaction, after that it is controlled by O2 diffusion in the solid α-Bi2O3 layer. The apparent activation energy is determined as 55.19 kJ/mol in liquid-phase oxidation.

Low-temperature catalytic oxidation of formaldehyde over Co_3O_4catalysts prepared using various precipitants

Co3O4 catalysts prepared with different precipitants（NH3·H2O,KOH,NH4HCO3,K2CO3 and KHCO3）were investigated for the oxidation of formaldehyde（HCHO）.Among these,KHCO3-precipitated Co3O4（KHCO3-Co） was the most active low-temperature catalyst,and was able to completely oxidize HCHO at the 100-ppm level to CO2 at 90℃.In situ diffuse reflectance infrared spectroscopy demonstrated that hydroxyl groups on the catalyst surface were regenerated by K~＋ and CO3^（2-）,thus promoting the oxidation of HCHO.Moreover,H2-temperature programmed reduction and X-ray photoelectron spectroscopy showed that employing KHCO3 as the precipitant increased the Co^3＋/Co^2＋molar ratio on the surface of the Co3O4 catalyst,thus further promoting oxidation.Structural characterization revealed that catalysts precipitated with carbonate or bicarbonate reagents exhibited greater specific surface areas and pore volumes.Overall,these data suggest that the high activity observed during the Co3O4 catalyzed oxidation of HCHO can be primarily attributed to the presence of K~＋ and CO3^（2-） on the Co3O4 surface and the favorable Co^3＋/Co^2＋ ratio.

Single atom gold catalysts for low-temperature CO oxidation

Low‐temperature CO oxidation is important for both fundamental studies and practical applica‐tions. Supported gold catalysts are generally regarded as the most active catalysts for low‐temperature CO oxidation. The active sites are traditionally believed to be Au nanoclusters or nanoparticles in the size range of 0.5–5 nm. Only in the last few years have single‐atom Au catalysts been proved to be active for CO oxidation. Recent advances in both experimental and theoretical studies on single‐atom Au catalysts unambiguously demonstrated that when dispersed on suitable oxide supports the Au single atoms can be extremely active for CO oxidation. In this mini‐review, recent advances in the development of Au single‐atom catalysts are discussed, with the aim of illus‐trating their unique catalytic features during CO oxidation.

Cyclic oxidation and hot corrosion of Al_2O_3 or Y_2O_3-dispersed low-temperature chromizing coating

Chromium coatings with and without Al_2O_3 or Y_2O_3 particles were prepared by chromizing the as-deposited Ni-film with and without Al_2O_3 or Y_2O_3 particles using a conventional pack-cementation method at 800 ℃. The cyclic oxidation at 800 ℃ and hot corrosion in molten 75% Na2SO4＋25% NaC1 at 800 ℃ of the three different chromizing coatings were investigated. The effects of Al_2O_3 or Y_2O_3 on the cyclic oxidation and hot corrosion behavior of the chromizing coatings were discussed. Microstructure results show that the codeposited Al_2O_3 or Y_2O_3 particles significantly retard the grain growth of the chromizing coating, which increases the cyclic oxidation and hot corrosion resistance of the chromizing coatings, due to the more rapid formation of purer and denser chromia scnle

Effect of different fillers on oxidation behavior of low-temperature chromizing coating

Three different chromizing coatings were produced on Ni substrate using a conventional pack-cementation method with Al2O3,Al2O3＋CeO2 and CeO2 acting as filler,respectively,at a greatly decreased temperature（700 ℃）.Effects of different fillers on the isothermal and cyclic oxidation resistance of chromizing coating in air at 850 ℃ were comparably investigated.Microstructure results show that the addition of CeO2 into the filler significantly retards the grain growth of the chromizing coating.Oxidation results indicate that the chromizing coating using CeO2 as filler exhibits somewhat increased oxidation resistance than the normal chromizmg coating,while the chromizing coating using Al2O3＋CeO2 as filler exhibits much better oxidation resistance.The effects of different fillers on the oxidation behaviors were discussed in detail.

Effects of Exogenous Glycine Betaine on Oxidation Metabolism in Cucumbers during Low-temperature Storage

[Objective] This study aimed to analyze the effects of different concentrations of glycine betaine（GB） on oxidation metabolism in cucumbers under low-temperature stress and to investigate the possible mechanism of low-temperature resistance in cucumber during low-temperature storage. [Method] Cucumber cultivar Zhongnong No.8 was treated with 0, 5, 10 and 15 mmol/L GB solutions for 15 min and stored at 4 ℃. Changes in oxidative metabolism-related parameters were observed. [Result] Increasing exogenous GB concentration could enhance GB content in cucumbers, decline lipoxygenase（LOX） activity, improve peroxidase（POD） and catalase（CAT） activities, remove effectively hydrogen peroxide（H2O2） and reduce the accumulation of malondialdehyde（MDA）. [Conclusion] Treating cucumbers with10 mmol/L GB exhibited the most remarkable effect.

Boosting oxygen reduction activity and CO_(2) resistance on bismuth ferrite-based perovskite cathode for low-temperature solid oxide fuel cells below 600℃

Developing efficient and stable cathodes for low-temperature solid oxide fuel cells(LT-SOFCs) is of great importance for the practical commercialization.Herein,we propose a series of Sm-modified Bi_(0.7-x)Sm_xSr_(0.3)FeO_(3-δ) perovskites as highly-active catalysts for LT-SOFCs.Sm doping can significantly enhance the electrocata lytic activity and chemical stability of cathode.At 600℃,Bi_(0.675)Sm_(0.025)Sr_(0.3)FeO_(3-δ)(BSSF25) cathode has been found to be the optimum composition with a polarization resistance of 0.098 Ω cm^2,which is only around 22.8% of Bi_(0.7)Sr_(0.3)FeO_(3-δ)(BSF).A full cell utilizing BSSF25 displays an exceptional output density of 790 mW cm^(-2),which can operate continuously over100 h without obvious degradation.The remarkable electrochemical performance observed can be attributed to the improved O_(2) transport kinetics,superior surface oxygen adsorption capacity,as well as O_(2)p band centers in close proximity to the Fermi level.Moreover,larger average bonding energy(ABE) and the presence of highly acidic Bi,Sm,and Fe ions restrict the adsorption of CO_(2) on the cathode surface,resulting in excellent CO_(2) resistivity.This work provides valuable guidance for systematic design of efficient and durable catalysts for LT-SOFCs.

Hypidone hydrochloride(YL-0919)ameliorates functional deficits after traumatic brain injury in mice by activating the sigma-1 receptor for antioxidation

Traumatic brain injury involves complex pathophysiological mechanisms,among which oxidative stress significantly contributes to the occurrence of secondary injury.In this study,we evaluated hypidone hydrochloride(YL-0919),a self-developed antidepressant with selective sigma-1 receptor agonist properties,and its associated mechanisms and targets in traumatic brain injury.Behavioral experiments to assess functional deficits were followed by assessment of neuronal damage through histological analyses and examination of blood-brain barrier permeability and brain edema.Next,we investigated the antioxidative effects of YL-0919 by assessing the levels of traditional markers of oxidative stress in vivo in mice and in vitro in HT22 cells.Finally,the targeted action of YL-0919 was verified by employing a sigma-1 receptor antagonist(BD-1047).Our findings demonstrated that YL-0919 markedly improved deficits in motor function and spatial cognition on day 3 post traumatic brain injury,while also decreasing neuronal mortality and reversing blood-brain barrier disruption and brain edema.Furthermore,YL-0919 effectively combated oxidative stress both in vivo and in vitro.The protective effects of YL-0919 were partially inhibited by BD-1047.These results indicated that YL-0919 relieved impairments in motor and spatial cognition by restraining oxidative stress,a neuroprotective effect that was partially reversed by the sigma-1 receptor antagonist BD-1047.YL-0919 may have potential as a new treatment for traumatic brain injury.

Ca and Sr co-doping induced oxygen vacancies in 3DOM La_(2-x)Sr_(x)Ce_(2-y)CayO_(7-δ)catalysts for boosting low-temperature oxidative coupling of methane

It is urgent to develop catalysts with application potential for oxidative coupling of methane(OCM)at relatively lower temperature.Herein,three-dimensional ordered macro porous(3 DOM)La_(2-x)Sr_(x)Ce_(2-y)CayO_(7-δ)(A_(2)B_(2)O_(7)-type)catalysts with disordered defective cubic fluorite phased structure were successfully prepared by a colloidal crystal template method.3DOM structure promotes the accessibility of the gaseous reactants(O2and CH4)to the active sites.The co-doping of Ca and Sr ions in La_(2-x)Sr_(x)Ce_(2-y)CayO_(7-δ)catalysts improved the formation of oxygen vacancies,thereby leading to increased density of surface-active oxygen species(O_(2)^(-))for the activation of CH4and the formation of C2products(C2H6and C2H4).3DOM La_(2-x)Sr_(x)Ce_(2-y)CayO_(7-δ)catalysts exhibit high catalytic activity for OCM at low temperature.3DOM La1.7Sr0.3Ce1.7Ca0.3O7-δcatalyst with the highest density of O_(2)^(-)species exhibited the highest catalytic activity for low-temperature OCM,i.e.,its CH4conversion,selectivity and yield of C2products at 650℃are 32.2%,66.1%and 21.3%,respectively.The mechanism was proposed that the increase in surface oxygen vacancies induced by the co-doping of Ca and Sr ions boosts the key step of C-H bond breaking and C-C bond coupling in catalyzing low-temperature OCM.It is meaningful for the development of the low-temperature and high-efficient catalysts for OCM reaction in practical application.

Enhancing performance of low-temperature processed CsPbI2Br all-inorganic perovskite solar cells using polyethylene oxide-modified TiO_(2)

CsPbX_(3)-based(X=I,Br,Cl)inorganic perovskite solar cells(PSCs)prepared by low-temperature process have attracted much attention because of their low cost and excellent thermal stability.However,the high trap state density and serious charge recombination between low-temperature processed TiO_(2)film and inorganic perovskite layer interface seriously restrict the performance of all-inorganic PSCs.Here a thin polyethylene oxide(PEO)layer is employed to modify TiO_(2)film to passivate traps and promote carrier collection.The impacts of PEO layer on microstructure and photoelectric characteristics of TiO_(2)film and related devices are systematically studied.Characterization results suggest that PEO modification can reduce the surface roughness of TiO_(2)film,decrease its average surface potential,and passivate trap states.At optimal conditions,the champion efficiency of CsPbI_(2)Br PSCs with PEO-modified TiO_(2)(PEO-PSCs)has been improved to 11.24%from 9.03%of reference PSCs.Moreover,the hysteresis behavior and charge recombination have been suppressed in PEO-PSCs.

Low-temperature chemistry in plasma-driven ammonia oxidative pyrolysis

Ammonia is gaining increasing attention as a green alternative fuel for achieving large-scale carbon emission reduction. Despite its potential technical prospects, the harsh ignition conditions and slow flame propagation speed of ammonia pose significant challenges to its application in engines. Non-equilibrium plasma has been identified as a promising method, but current research on plasma-enhanced ammonia combustion is limited and primarily focuses on ignition characteristics revealed by kinetic models. In this study, low-temperature and low-pressure chemistry in plasma-assisted ammonia oxidative pyrolysis is investigated by integrated studies of steady-state GC measurements and mathematical simulation. The detailed kinetic mechanism of NH_(3) decomposition in plasma-driven Ar/NH_(3) and Ar/NH_(3)/O_(2) mixtures has been developed. The numerical model has good agreements with the experimental measurements in NH_(3)/O_(2) consumption and N_(2)/H_(2) generation, which demonstrates the rationality of modelling. Based on the modelling results, species density profiles, path flux and sensitivity analysis for the key plasmaproduced species such as NH_(2), NH, H_(2), OH, H, O, O(^(1)D), O_(2)(a^(1)△_(g)), O_(2)(b^(1)∑_(g)^(+)), Ar^(*), H^(-), Ar^(+), NH_(3)^(+), O_(2)^(-) in the discharge and afterglow are analyzed in detail to illustrate the effectiveness of the active species on NH_(3) excitation and decomposition at low temperature and relatively higher E/N values. The results revealed that NH_(2), NH, H as well as H_(2) are primarily generated through the electron collision reactions e + NH_(3)→ e + NH_(2)+ H, e + NH_(3)→ e + NH + H_(2) and the excited-argon collision reaction Ar^(*) + NH_(3)+ H → Ar + NH_(2)+ 2H, which will then react with highly reactive oxidative species such as O_(2)^(*), O^(*), O, OH, and O_(2) to produce stable products of NOx and H_(2)O. NH_(3)→ NH is found a specific pathway for NH_(3) consumption with plasma assistance, which further highlights the enhanced kinetic effects.

Low-temperature catalytic oxidation of NO over Mn-Ce-O_x catalyst

A series of manganese-cerium oxide catalysts were prepared by different methods and used for low-temperature catalytic oxidation of NO in the presence of excess O2.Their surface properties were evaluated by means of BET and were characterized by using scanning electron microscopy(SEM) and X-ray diffractometer(XRD).The activity test of Mn-Ce-Ox catalysts showed that addition of Ce enhanced the activities of NO oxidation.The most active catalysts with a molar Ce/(Mn+Ce) ratio of 0.3 were prepared by co-precip...

A comparative study of CuO/TiO_2-SnO_2,CuO/TiO_2 and CuO/SnO_2 catalysts for low-temperature CO oxidation

Nanometer SnO2 particles were synthesized by sol-gel dialytic processes and used as a support to prepare CuO supported catalysts via a deposition-precipitation method. The samples were characterized by means of TG-DTA, XRD, H2-TPR and XPS. The catalytic activity of the CuO/TiO2-SnO2 catalysts was markedly depended on the loading of CuO, and the optimum CuO loading was 8 wt.% （Tloo = 80 ℃）. The CuO/TiO2-SnO2 catalysts exhibited much higher catalytic activity than the CuO/TiO2 and CuO/SnO2 catalysts. H2-TPR result indicated that a large amount of CuO formed the active site for CO oxidation in 8 wt.% CuO/TiO2-SnO2 catalyst.

Low-temperature oxidation behavior of MoSi_2 powders

The oxidation behavior of molybdenum disilicide （MoSi2） powders at 400, 500, and 600℃ for 12 h in air were investigated by using X-ray diffraction （XRD） and transmission electron microscopic （TEM） techniques. Significant changes were observed in volume, mass, and color. Especially at 500℃, the volume expansion was found to be as high as 7-8 times, the color changed from black to yellow-white, and the mass gain was about 169.34% after 8 h, with SiO2 and MoO3 as main reaction products. The gains in volume and mass were less at 400 and 600℃ compared with those at 500℃, probably due to the less reaction rate at 400℃ and the formation of silica glass scale at 600℃, which would protect the matrix and restrain the diffusion of oxygen and molybdenum. Thus, the accelerated oxidation behavior of MoSi2 powder appeared at 500℃ and the volume expansion was the sign of accelerated oxidation.

In situ catalytic upgrading of heavy crude oil through low-temperature oxidation

The low-temperature catalytic oxidation of heavy crude oil（Xinjiang Oilfield,China） was studied using three types of catalysts including oil-soluble,watersoluble,and dispersed catalysts.According to primary screening,oil-soluble catalysts,copper naphthenate and manganese naphthenate,are more attractive,and were selected to further investigate their catalytic performance in in situ upgrading of heavy oil.The heavy oil compositions and molecular structures were characterized by column chromatography,elemental analysis,and Fourier transform infrared spectrometry before and after reaction.An Arrhenius kinetics model was introduced to calculate the rheological activation energy of heavy oil from the viscosity-temperature characteristics.Results show that the two oil-soluble catalysts can crack part of heavy components into light components,decrease the heteroatom content,and achieve the transition of reaction mode from oxygen addition to bond scission.The calculated rheological activation energy of heavy oil from the fitted Arrhenius model is consistent with physical properties of heavy oil（oil viscosity and contents of heavy fractions）.It is found that the temperature,oil composition,and internal molecular structures are the main factors affecting its flow ability.Oil-soluble catalyst-assisted air injection or air huff-n-puff injection is a promising in situ catalytic upgrading method for improving heavy oil recovery.

Understanding the roles of Brønsted/Lewis acid sites on manganese oxide-zeolite hybrid catalysts for low-temperature NH_(3)-SCR

Although metal oxide-zeolite hybrid materials have long been known to achieve enhanced catalytic activity and selectivity in NO_(x)removal reactions through the inter-particle diffusion of intermediate species,their subsequent reaction mechanism on acid sites is still unclear and requires investigation.In this study,the distribution of Brønsted/Lewis acid sites in the hybrid materials was precisely adjusted by introducing potassium ions,which not only selectively bind to Brønsted acid sites but also potentially affect the formation and diffusion of activated NO species.Systematic in situ diffuse reflectance infrared Fourier transform spectroscopy analyses coupled with selective catalytic reduction of NO_(x)with NH_(3)(NH_(3)-SCR)reaction demonstrate that the Lewis acid sites over MnO_(x)are more active for NO reduction but have lower selectivity to N_(2)than Brønsted acids sites.Brønsted acid sites primarily produce N_(2),whereas Lewis acid sites primarily produce N_(2)O,contributing to unfavorable N_(2)selectivity.The Brønsted acid sites present in Y zeolite,which are stronger than those on MnO_(x),accelerate the NH_(3)-SCR reaction in which the nitrite/nitrate species diffused from the MnO_(x)particles rapidly convert into the N_(2).Therefore,it is important to design the catalyst so that the activated NO species formed in MnO_(x)diffuse to and are selectively decomposed on the Brønsted acid sites of H-Y zeolite rather than that of MnO_(x)particle.For the physically mixed H-MnO_(x)+H-Y sample,the abundant Brønsted/Lewis acid sites in H-MnO_(x)give rise to significant consumption of activated NO species before their inter-particle diffusion,thereby hindering the enhancement of the synergistic effects.Furthermore,we found that the intercalated K+in K-MnO_(x)has an unexpected favorable role in the NO reduction rate,probably owing to faster diffusion of the activated NO species on K-MnO_(x)than H-MnO_(x).This study will help to design promising metal oxide-zeolite hybrid catalysts by identifying the role of the acid sites in two different constituents.

Exploring the Low-Temperature Oxidation Chemistry of Cyclohexane in a Jet-Stirred Reactor:an Experimental and Kinetic Modeling Study

We report the investigation on the low-temperature oxidation of cyclohexane in a jet-stirred reactor over 500-742 K. Synchrotron vacuum ultraviolet photoionization mass spectrometry （SVUV-PIMS） was used for identifying and quantifying the oxidation species. Major products, cyclic olefins, and oxygenated products including reactive hydroperoxides and high oxygen compounds were detected. Compared with n-alkanes, a narrow low-temperature window （-80 K） was observed in the low-temperature oxidation of cyclohexane. Besides, a kinetic model for cyclohexane oxidation was developed based on the CNRS model [Combust. Flame 160, 2319 （2013）], which can better capture the experimental results than previous models. Based on the modeling analysis, the 1,5-H shift dominates the crucial isomerization steps of the first and second O2 addition products in the low-temperature chain branching process of cyclohexane. The negative temperature coefficient behavior of cyclohexane oxidation results from the reduced chain branching due to the competition from chain inhibition and propagation reactions, i.e. the reaction between cyclohexyl radical and O2 and the de- composition of cyclohexylperoxy radical, both producing cyclohexene and HO2 radical, as well as the decomposition of cyclohexylhydroperoxy radical producing hex-5-en-l-al and OH radical.

Changes in active functional groups during low-temperature oxidation of coal

Using Fourier Transform Infrared (FTIR) combined with an adiabatic oxidation test, temperature-programmed oxidation and gas analysis, we studied the changes of active functional groups during low-temperature oxidation of lignite, gas coal, fat coal and anthracite. During slow low-temperature heat accumulation, aliphatic hydrocarbons, such as methyl and methylene, are attacked by oxygen atoms absorbed by pores on coal surfaces, generating unstable solid intermediate carbon-oxygen complexes, which then decompose into gaseous products (CO, CO2) and stable solid complexes. At the accelerated oxidation stage, the stable complexes begin to decompose in large amounts and provided new active sites for further oxidation, while the aliphatic structures gained energy and fell from the benzene rings to produce CxHy and H2.

Construction of a macromolecular structural model of Chinese lignite and analysis of its low-temperature oxidation behavior

The aim of this paper is to analyze the change in the active structure of lignite during the process of lowtemperature oxidation by constructing a molecular structure model for lignite. Using quantum computation combined with experimental results of proximate analysis, ultimate analysis, Fourier transform infrared spectroscopy(FTIR) and X-ray photoelectron spectroscopy(XPS), a structural model for the large molecular structure was constructed. By analyzing the bond lengths in the model molecule, the evolution law for the active structure of lignite was predicted for the process of low-temperature oxidation. In low-temperature oxidation,alkanes and hydroxyls are the primary active structures observed in lignite, though ether may also react. These active functional groups react with oxygen to release heat, thereby speeding up the reaction between coal and oxygen. Finally, the content of various functional groups in the process of lignite low-temperature oxidation was analyzed by infrared analysis, and the accuracy of the model was verified.