The ability of a novel nonionic CO2 -soluble surfactant to propagate foam in porous media was compared with that of a conventional anionic surfactant(aqueous soluble only)through core floods with Berea sandstone cor...The ability of a novel nonionic CO2 -soluble surfactant to propagate foam in porous media was compared with that of a conventional anionic surfactant(aqueous soluble only)through core floods with Berea sandstone cores.Both simultaneous and alternating injections have been tested.The novel foam outperforms the conventional one with respect to faster foam propagation and higher desaturation rate.Furthermore,the novel injection strategy,CO2 continuous injection with dissolved CO2 -soluble surfactant,has been tested in the laboratory.Strong foam presented without delay.It is the first time the measured surfactant properties have been used to model foam transport on a field scale to extend our findings with the presence of gravity segregation.Different injection strategies have been tested under both constant rate and pressure constraints.It was showed that novel foam outperforms the conventional one in every scenario with much higher sweep efficiency and injectivity as well as more even pressure redistribution.Also,for this novel foam,it is not necessary that constant pressure injection is better,which has been concluded in previous literature for conventional foam.Furthermore,the novel injection strategy,CO2 continuous injection with dissolved CO2 -soluble surfactant,gave the best performance,which could lower the injection and water treatment cost.展开更多
Foamable high melt strength polypropylene (HMSPP) was prepared by grafting styrene (St) onto polypropylene (PP) and simultaneously introducing poly- dimethylsiloxane (PDMS) through a one-step melt extru- sion ...Foamable high melt strength polypropylene (HMSPP) was prepared by grafting styrene (St) onto polypropylene (PP) and simultaneously introducing poly- dimethylsiloxane (PDMS) through a one-step melt extru- sion process. The effect of PDMS viscosity on the foaming behavior of HMSPP was systematically investigated using supercritical CO2 as the foaming agent. The results show that the addition of PDMS has little effect on the grafting reaction of St and HMSPP exhibits enhanced elastic response and obvious strain hardening effect. Though the CO2 solubility of HMSPP with PDMS (PDMS-HMSPP) is lower than that of HMSPP without PDMS, especially for PDMS with low viscosity, the PDMS-HMSPP foams exhibit narrow cell size distribution and high cell density. The fracture morphology of PDMS-HMSPP shows that PDMS with low viscosity disperses more easily and uniformly in HMSPP matrix, leading to form small domains during the extrusion process. These small domains act as bubble nucleation sites and thus may be responsible for the improved foaming performance of HMSPP.展开更多
A self-cooling dielectric barrier discharge reactor, packed with foamed Cu and Ni mesh and operated at ambient conditions, was used for the composition of CO2 into CO and O2.The influences of power, frequency, and oth...A self-cooling dielectric barrier discharge reactor, packed with foamed Cu and Ni mesh and operated at ambient conditions, was used for the composition of CO2 into CO and O2.The influences of power, frequency, and other discharge characteristics were investigated in order to have a better understanding of the effect of the packing materials on CO2 decomposition.It is found that porous foamed Cu and Ni not only played a role as the carrier of energy transformation and electrode distributed in discharge gaps but also promoted the equilibrium shifting toward the product side to yield more CO by consuming some part of O2 and O radicals generated from the decomposition of CO2.The maximum CO2 decomposition rates of 48.6%and 49.2% and the maximum energy efficiency of 9.71% and 10.18% were obtained in the foamed Ni and Cu mesh, respectively.展开更多
CO2-copolymer based polyurethane foams were synthesized and characterized in this paper. The foams were found to have higher strength and lower heat of combustion than the conventional polyether polyurethane foams. ...CO2-copolymer based polyurethane foams were synthesized and characterized in this paper. The foams were found to have higher strength and lower heat of combustion than the conventional polyether polyurethane foams. They may find wide applications in many fields.展开更多
Carbon dioxide(CO2) flooding is one of the most globally used EOR processes to enhance oil recovery.However,the low gas viscosity and density result in gas channeling and gravity override which lead to poor sweep effi...Carbon dioxide(CO2) flooding is one of the most globally used EOR processes to enhance oil recovery.However,the low gas viscosity and density result in gas channeling and gravity override which lead to poor sweep efficiency.Foam application for mobility control is a promising technology to increase the gas viscosity,lower the mobility and improve the sweep efficiency in the reservoir.Foam is generated in the reservoir by co-injection of surfactant solutions and gas.Although there are many surfactants that can be used for such purpose,their performance with supercritical CO2(ScCO2) is weak causing poor or loss of mobility control.This experimental study evaluates a newly developed surfactant(CNF) that was introduced for ScCO2 mobility control in comparison with a common foaming agent,anionic alpha olefin sulfonate(AOS) surfactant.Experimental work was divided into three stages:foam static tests,interfacial tension measurements,and foam dynamic tests.Both surfactants were investigated at different conditions.In general,results show that both surfactants are good foaming agents to reduce the mobility of ScCO2 with better performance of CNF surfactant.Shaking tests in the presence of crude oil show that the foam life for CNF extends to more than 24 h but less than that for AOS.Moreover,CNF features lower critical micelle concentration(CMC),higher adsorption,and smaller area/molecule at the liquid-air interface.Furthermore,entering,spreading,and bridging coefficients indicate that CNF surfactant produces very stable foam with light crude oil in both deionized and saline water,whereas AOS was stable only in deionized water.At all conditions for mobility reduction evaluation,CNF exhibits stronger flow resistance,higher foam viscosity,and higher mobility reduction factor than that of AOS surfactant.In addition,CNF and ScCO2 simultaneous injection produced 8.83% higher oil recovery than that of the baseline experiment and 7.87% higher than that of AOS.Pressure drop profiles for foam flooding using CNF was slightly higher than that of AOS indicating that CNF is better in terms of foam-oil tolerance which resulted in higher oil recovery.展开更多
文摘The ability of a novel nonionic CO2 -soluble surfactant to propagate foam in porous media was compared with that of a conventional anionic surfactant(aqueous soluble only)through core floods with Berea sandstone cores.Both simultaneous and alternating injections have been tested.The novel foam outperforms the conventional one with respect to faster foam propagation and higher desaturation rate.Furthermore,the novel injection strategy,CO2 continuous injection with dissolved CO2 -soluble surfactant,has been tested in the laboratory.Strong foam presented without delay.It is the first time the measured surfactant properties have been used to model foam transport on a field scale to extend our findings with the presence of gravity segregation.Different injection strategies have been tested under both constant rate and pressure constraints.It was showed that novel foam outperforms the conventional one in every scenario with much higher sweep efficiency and injectivity as well as more even pressure redistribution.Also,for this novel foam,it is not necessary that constant pressure injection is better,which has been concluded in previous literature for conventional foam.Furthermore,the novel injection strategy,CO2 continuous injection with dissolved CO2 -soluble surfactant,gave the best performance,which could lower the injection and water treatment cost.
基金Acknowledgements This work was financially supported by National Natural Science Foundation of China (Grant Nos. 21476085 and 21306047), Fundamental Research Funds for the Central Universities of China (22A201514016 222201314051).
文摘Foamable high melt strength polypropylene (HMSPP) was prepared by grafting styrene (St) onto polypropylene (PP) and simultaneously introducing poly- dimethylsiloxane (PDMS) through a one-step melt extru- sion process. The effect of PDMS viscosity on the foaming behavior of HMSPP was systematically investigated using supercritical CO2 as the foaming agent. The results show that the addition of PDMS has little effect on the grafting reaction of St and HMSPP exhibits enhanced elastic response and obvious strain hardening effect. Though the CO2 solubility of HMSPP with PDMS (PDMS-HMSPP) is lower than that of HMSPP without PDMS, especially for PDMS with low viscosity, the PDMS-HMSPP foams exhibit narrow cell size distribution and high cell density. The fracture morphology of PDMS-HMSPP shows that PDMS with low viscosity disperses more easily and uniformly in HMSPP matrix, leading to form small domains during the extrusion process. These small domains act as bubble nucleation sites and thus may be responsible for the improved foaming performance of HMSPP.
基金financially supported by the National Natural Science Foundation of China (No.21663022)
文摘A self-cooling dielectric barrier discharge reactor, packed with foamed Cu and Ni mesh and operated at ambient conditions, was used for the composition of CO2 into CO and O2.The influences of power, frequency, and other discharge characteristics were investigated in order to have a better understanding of the effect of the packing materials on CO2 decomposition.It is found that porous foamed Cu and Ni not only played a role as the carrier of energy transformation and electrode distributed in discharge gaps but also promoted the equilibrium shifting toward the product side to yield more CO by consuming some part of O2 and O radicals generated from the decomposition of CO2.The maximum CO2 decomposition rates of 48.6%and 49.2% and the maximum energy efficiency of 9.71% and 10.18% were obtained in the foamed Ni and Cu mesh, respectively.
基金This project was supported by the National Natural Science Foundation of China(No.20274053).
文摘CO2-copolymer based polyurethane foams were synthesized and characterized in this paper. The foams were found to have higher strength and lower heat of combustion than the conventional polyether polyurethane foams. They may find wide applications in many fields.
文摘Carbon dioxide(CO2) flooding is one of the most globally used EOR processes to enhance oil recovery.However,the low gas viscosity and density result in gas channeling and gravity override which lead to poor sweep efficiency.Foam application for mobility control is a promising technology to increase the gas viscosity,lower the mobility and improve the sweep efficiency in the reservoir.Foam is generated in the reservoir by co-injection of surfactant solutions and gas.Although there are many surfactants that can be used for such purpose,their performance with supercritical CO2(ScCO2) is weak causing poor or loss of mobility control.This experimental study evaluates a newly developed surfactant(CNF) that was introduced for ScCO2 mobility control in comparison with a common foaming agent,anionic alpha olefin sulfonate(AOS) surfactant.Experimental work was divided into three stages:foam static tests,interfacial tension measurements,and foam dynamic tests.Both surfactants were investigated at different conditions.In general,results show that both surfactants are good foaming agents to reduce the mobility of ScCO2 with better performance of CNF surfactant.Shaking tests in the presence of crude oil show that the foam life for CNF extends to more than 24 h but less than that for AOS.Moreover,CNF features lower critical micelle concentration(CMC),higher adsorption,and smaller area/molecule at the liquid-air interface.Furthermore,entering,spreading,and bridging coefficients indicate that CNF surfactant produces very stable foam with light crude oil in both deionized and saline water,whereas AOS was stable only in deionized water.At all conditions for mobility reduction evaluation,CNF exhibits stronger flow resistance,higher foam viscosity,and higher mobility reduction factor than that of AOS surfactant.In addition,CNF and ScCO2 simultaneous injection produced 8.83% higher oil recovery than that of the baseline experiment and 7.87% higher than that of AOS.Pressure drop profiles for foam flooding using CNF was slightly higher than that of AOS indicating that CNF is better in terms of foam-oil tolerance which resulted in higher oil recovery.