The protective behavior for a molten AZ91D alloy in an open melting furnace was investigated under a protective gas mixture containing 3% SO2 and 97% CO2, and the protection mechanism was discussed. Experimental resul...The protective behavior for a molten AZ91D alloy in an open melting furnace was investigated under a protective gas mixture containing 3% SO2 and 97% CO2, and the protection mechanism was discussed. Experimental results show that the gas mixture provides effective protection for AZ91D melt in the temperature range from 680 ℃ to 730 ℃. The microstructure, chemical composition and phase composition of the surface film formed on the molten AZ91D alloy were analyzed using scanning electron microscopy （SEM） with energy dispersive spectrometer （EDS） and X-ray diffraction （XRD）. The SEM results demonstrate that the surface films with an average thickness between 0.5 pm and 2 pm are dense and coherent in the protected temperature range. The EDS results reveal that the surface film mainly contains elements S, C, O, AI and Mg. The XRD results show that the surface film consists of MgO, MgS and a small amount of C phase.展开更多
CF3I gas mixtures have attracted considerable attention as potential environmentally-friendly alternatives to SF6 gas,owing to their excellent insulating performance.This paper attempts to study the CF3I ternary gas m...CF3I gas mixtures have attracted considerable attention as potential environmentally-friendly alternatives to SF6 gas,owing to their excellent insulating performance.This paper attempts to study the CF3I ternary gas mixtures with c-C4F8 and buffer gases N2 and CO2 by considering dielectric strength from electron transport parameters based on the Boltzmann method and synergistic effect analysis,compared with SF6 gas mixtures.The results confirm that the critical electric field strength of CF3I/c-C4F8/70%CO2 is greater than that of 30%SF6/70%CO2 when the CF3I content is greater than 17%.Moreover,a higher content of c-C4F8 decreases the sensitivity of gas mixtures to an electric field,and this phenomenon is more obvious in CF3I/c-C4F8/CO2 gas mixtures.The synergistic effects for CF3I/c-C4F8/70%N2 were most obvious when the c-C4F8 content was approximately 20%,and for CF3I/c-C4F8/70%CO2 when the c-C4F8 content was approximately 10%.On the basis of this research,CF3I/c-C4F8/70%N2 shows better insulation performance when the c-C4F8 content is in the15%–20%range.For CF3I/c-C4F8/70%CO2,when the c-C4F8 content is in the 10%–15%range,the gas mixtures have excellent performance.Hence,these gas systems might be used as alternative gas mixtures to SF6 in high-voltage equipment.展开更多
To obtain the fundamental data of CO2/N2 gas mixture hydrate formation kinetics and CO2 separation and sequestration mechanisms,the gas hydrate formation process by a binary CO2/N2 gas mixture(50:50)in fine sediments(...To obtain the fundamental data of CO2/N2 gas mixture hydrate formation kinetics and CO2 separation and sequestration mechanisms,the gas hydrate formation process by a binary CO2/N2 gas mixture(50:50)in fine sediments(150–250μm)was investigated in a semibatch vessel at variable temperatures(273,275,and 277 K)and pressures(5.8–7.8 MPa).During the gas hydrate reaction process,the changes in the gaseous phase composition were determined by gas chromatography.The results indicate that the gas hydrate formation process of the binary CO2/N2 gas mixture in fine sediments can be reduced to two stages.Firstly,the dissolved gas containing a large amount of CO2 formed gas hydrates,and then gaseous N2 participated in the gas hydrate formation.In the second stage,all the dissolved gas was consumed.Thus,both gaseous CO2 and N2 diffused into sediment.The first stage in different experiments lasted for 5–15 h,and>60%of the gas was consumed in this period.The gas consumption rate was greater in the first stage than in the second stage.After the completion of gas hydrate formation,the CO2 content in the gas hydrate was more than that in the gas phase.This indicates that CO2 formed hydrate easily than N2 in the binary mixture.Higher operating pressures and lower temperatures increased the gas consumption rate of the binary gas mixture in gas hydrate formation.展开更多
The potential energy snrface of a CO2-N2 mixture is determined by using an inversion method, together with a new collision integral correlation [J. Phys. Chem. R@ Data 19 1179 （1990）]. With the new invert potential,...The potential energy snrface of a CO2-N2 mixture is determined by using an inversion method, together with a new collision integral correlation [J. Phys. Chem. R@ Data 19 1179 （1990）]. With the new invert potential, the transport properties of CO2-N2 mixture are presented in a temperature range front 273.15 K to 3273.15 K at low density by employing the Chapman-Enskog scheme and the Wang Chang-Uhlenbeck de Boer theory, consisting of a viscosity coefficient, a thermal conductivity coefficient, a binary diffusion coefficient, and a thermal diffusion factor. The accuracy of the predicted results is estimated to be 2% for viscosity, 5% for thermal conductivity, and 10% for binary diffusion coefficient.展开更多
We calculated the uniform dielectric breakdown field strength of residual 30% CF3I/CO2 gas mixtures during the arc extinction process over the temperature range 300-3500 K at 0.1 MPa. The limiting reduced field streng...We calculated the uniform dielectric breakdown field strength of residual 30% CF3I/CO2 gas mixtures during the arc extinction process over the temperature range 300-3500 K at 0.1 MPa. The limiting reduced field strengths are decided by a balance of electron generation and loss based on chemical reactions estimated by the electron energy distribution function （EEDF）, which employs the Boltzmann equation method with two-term expanding approximation in the steady-state Townsend （SST） condition. During the insulation recovery phase, the hot CF3I/CO2 gas mixtures have maximum dielectric strength at a temperature of about 1500 K. At room temperature 300 K, the electric strength after arc extinction （90.3 Td, 1 Td=10-21 V.m2） is only 38% of the original value before arc （234.9 Td）. The adverse insulation recovery ability of CF3I/CO2 gas mixtures in arc extinction hinders its application in electric circuit breakers and other switchgears as an arc quenching and insulating medium.展开更多
Monte Carlo simulations are adopted to study the electron motion in the mixture of H2 and CH4 during diamond synthesis via Glow Plasma-assisted Chemical Vapor Deposition (GPCVD). The non-uniform electric field is used...Monte Carlo simulations are adopted to study the electron motion in the mixture of H2 and CH4 during diamond synthesis via Glow Plasma-assisted Chemical Vapor Deposition (GPCVD). The non-uniform electric field is used and the avalanche of electrons is taken into account in this simulation. The average energy distribution of electrons and the space distribution of effective species such as CH3, CH+3, CH+ and H at various gas pressures are given in this paper, and optimum experimental conditions are inferred from these results.展开更多
Highly selective separation of CO_2 from its methane-containing binary gas mixture can be achieved by using Poly(ether-block-amide)(PEBAX)mixed matrix membranes(MMMs).According to FESEM and AFM analyses,silica-based n...Highly selective separation of CO_2 from its methane-containing binary gas mixture can be achieved by using Poly(ether-block-amide)(PEBAX)mixed matrix membranes(MMMs).According to FESEM and AFM analyses,silica-based nanoparticles were homogenously integrated within the polymer matrix,facilitating penetration of CO_2 through the membrane while acting as barrier for methane gas.The membrane containing 4.6 wt% fumed silica(FS)(PEBAX/4.6 wt%FS)exhibits astonishing selectivity results where binary gas mixture of CO_2/CH_4 was used as feed gas.As detected by gas chromatography,in the permeate side,data showed a significant increase of CO_2 permeance,while CH_4 transport through the mixed matrix membrane was not detectable.Moreover,PEBAX/4.6 wt%FS greatly exceeds the Robeson limit.According to data reported on CO_2/CH_4 gas pair separation in the literature,the results achieved in this work are beyond those data reported in the literature,particularly when PEBAX/4.6 wt%FS membrane was utilized.展开更多
A series of modifiedγ-Al_2O_3supported iron-based catalysts(M-Fe/γ-Al_2O_3)was developed to reduce SO_2in actual smelter off-gases using CO–H_2gas mixture as reducing agent for sulfur production.Used as modifiers,t...A series of modifiedγ-Al_2O_3supported iron-based catalysts(M-Fe/γ-Al_2O_3)was developed to reduce SO_2in actual smelter off-gases using CO–H_2gas mixture as reducing agent for sulfur production.Used as modifiers,three metal additives—Ni,Co,and Ce were added to Fe/γ-Al_2O_3catalysts.Changes in catalyst structure and active phase were characterized with X-ray diffraction,XPS,SEM,and EDS.The reduction ability of catalysts was exhibited via CO-TPR.The prepared catalysts only need to be pre-reacted for a period of time,eliminating the need for presulfidation treatment.Reaction conditions were optimized in a fixed bed reactor to achieve high SO_2conversion and sulfur selectivity.XRD characterization was carried out to verify the resulting sulfur products.Combining in situ infrared characterization and catalyst evaluation of support and active component,the reaction mechanism was investigated and proposed.展开更多
The effects of 5 wt.-% Al and 10 wt.-% Al on the sulfidation behaviour of the Fe-25Cralloy in H<sub>2</sub>S-H<sub>2</sub> gas mixtures in the temperature range of 700～900 C has been studied.T...The effects of 5 wt.-% Al and 10 wt.-% Al on the sulfidation behaviour of the Fe-25Cralloy in H<sub>2</sub>S-H<sub>2</sub> gas mixtures in the temperature range of 700～900 C has been studied.Thesulfidation resistance of Fe-25Cr was improved and the sulfide scale morphologies,compositionand structure of Fe-25Cr changed remarkably.The sulfidation kinetics of the alloys with alu-minium obeyed basically the parabolic law after an initial period of reaction time.The sulfida-tion mechanism of the Fe-Cr-Al alloy has been proposed.展开更多
This experiment was conducted in Xinxiang, Henan from June 2013 to June 2014. Total four treatments were designed including farmers ’ common practice （F, 250 kg/hm^2）, 80% F （LF, 200 kg/hm^2）, 80% F＋biochar （LF...This experiment was conducted in Xinxiang, Henan from June 2013 to June 2014. Total four treatments were designed including farmers ’ common practice （F, 250 kg/hm^2）, 80% F （LF, 200 kg/hm^2）, 80% F＋biochar （LFC） and no fertilizer （CK） to measure the dynamic emissions of CO2 and N2O from a summer maize-winter wheat field by static chamber-gas chromatography method. The results showed that the soil CO2 emission was 21.8-1 022.7 mg/（m^2·h）, and was mainly influenced by soil temperature and moisture content. During the growth of summer maize, the soil CO2 emission was more significantly affected by soil moisture con-tent; and in winter wheat growing season, it was more significantly affected by soil temperature in the top 5 cm. The LF and LFC treatments significantly reduced the soil cumulative CO2 emission, especial y during the growth of winter wheat. Fertiliza-tion and irrigation were the main factors influencing the soil N2O emission. The soil N2O emission during the fertilization period accounted for 73.9%-74.5% and 40.5%-43.6% of the soil cumulative N2O emission during the summer maize-and winter wheat-growing season, respectively. The peak of emission fluxes was determined by fertilization amount, while the occurrence time of emission peak and emission re-duction effect were influenced by irrigation. The LF treatment reduced the soil cu-mulative N2O emission by 15.7%-16.8% and 18.1%-18.5% during the growth period of summer maize and winter wheat, respectively. Reduced nitrogen fertilization is an effective way for reducing N2O emission in intensive high-yielding farmland. Under a suitable nitrogen level （200 kg/hm^2）, the application of biochar showed no significant effect on the soil N2O emission in a short term. The N2O emission factors of the L and LF treatments were 0.60% and 0.56%, respectively. ln the intensive high-yield-ing farmland of North China, reducing the nitrogen application amount is an appro-priate measure to mitigate greenhouse gas emissions without crop yield loss.展开更多
In order to better understand the prevailing mechanism of CO2 storage in coal and estimate CO2 sequestration capacity of a coal seam and enhanced coalbed methane recovery （ECBM） with CO2 injection into coal, we inve...In order to better understand the prevailing mechanism of CO2 storage in coal and estimate CO2 sequestration capacity of a coal seam and enhanced coalbed methane recovery （ECBM） with CO2 injection into coal, we investigated the preferential adsorption of CH4 and CO2 on coals. Adsorption of pure CO2, CH4 and their binary mixtures on high-rank coals from Qinshui Basin in China were employed to study the preferential adsorption behaviour. Multiple regression equations were presented to predict CH4 equi- librium concentration from equilibrium pressure and its initial-composition in feed gas. The results show that preferential adsorption of CO2 on coals over the entire pressure range under competitive sorption conditions was observed, however, preferential adsorption of CH4 over CO2 on low-volatile bituminous coal from higher CH4-compostion in source gas was found at up to 1O MPa pressure. Preferential adsorp- tion of CO2 increases with increase of CH4 concentration in source gas, and decreases with increasing pressure. Although there was no systematic investigation of the effect of coal rank on preferential adsorp- tion, there are obvious differences in preferential adsorption of gas between low-volatile bituminous coal and anthracite. The obtained preferential adsorption gives rise to the assumption that CO2 sequestration in coal beds with subsequent CO2-ECBM might be an ootion in Qinshui Basins, China.展开更多
高压断路器分合闸过程中触头间隙介质的绝缘强度及其变化是断路器结构设计的重要性能指标。搭建高压断路器触头间隙介质绝缘特性实验回路,测量C_(4)F_(7)N/CO_(2)混合气体断路器空载分合闸过程中不同压强、不同C4F7N含量时触头间隙介质...高压断路器分合闸过程中触头间隙介质的绝缘强度及其变化是断路器结构设计的重要性能指标。搭建高压断路器触头间隙介质绝缘特性实验回路,测量C_(4)F_(7)N/CO_(2)混合气体断路器空载分合闸过程中不同压强、不同C4F7N含量时触头间隙介质的动态击穿电压,研究C_(4)F_(7)N/CO_(2)混合气体断路器的关合预击穿特性和分闸绝缘特性。实验发现,断路器空载分合闸过程中C_(4)F_(7)N/CO_(2)混合气体动态击穿电压存在“低电压击穿”现象;合闸过程中,动态击穿电压分散性较大,C_(4)F_(7)N/CO_(2)混合气体断路器的关合预击穿特性显著劣于SF6断路器,增大压强或增加C4F7N含量对混合气体动态击穿电压分散性的改善不大;正、负极性条件下0.7MPa时9%C_(4)F_(7)N/91%CO_(2)混合气体的分闸平均绝缘强度上升率(rate of rise of dielectric strength,RRDS)分别为49.8kV/ms和42.7kV/ms,具有“反极性”效应;分闸过程中,“低电压击穿”现象主要出现在刚分后2ms(开距约6mm)范围以内,断路器若在此时间(开距)范围内熄弧,极易发生弧后重击穿现象,因此,C_(4)F_(7)N/CO_(2)混合气体断路器结构设计时应避免在此范围内熄弧。展开更多
基金supported by the Ministry of Science and Technology Project of China(2009, No. GJB20011)
文摘The protective behavior for a molten AZ91D alloy in an open melting furnace was investigated under a protective gas mixture containing 3% SO2 and 97% CO2, and the protection mechanism was discussed. Experimental results show that the gas mixture provides effective protection for AZ91D melt in the temperature range from 680 ℃ to 730 ℃. The microstructure, chemical composition and phase composition of the surface film formed on the molten AZ91D alloy were analyzed using scanning electron microscopy （SEM） with energy dispersive spectrometer （EDS） and X-ray diffraction （XRD）. The SEM results demonstrate that the surface films with an average thickness between 0.5 pm and 2 pm are dense and coherent in the protected temperature range. The EDS results reveal that the surface film mainly contains elements S, C, O, AI and Mg. The XRD results show that the surface film consists of MgO, MgS and a small amount of C phase.
基金supported by National Natural Science Foundation of China(No.51337006)。
文摘CF3I gas mixtures have attracted considerable attention as potential environmentally-friendly alternatives to SF6 gas,owing to their excellent insulating performance.This paper attempts to study the CF3I ternary gas mixtures with c-C4F8 and buffer gases N2 and CO2 by considering dielectric strength from electron transport parameters based on the Boltzmann method and synergistic effect analysis,compared with SF6 gas mixtures.The results confirm that the critical electric field strength of CF3I/c-C4F8/70%CO2 is greater than that of 30%SF6/70%CO2 when the CF3I content is greater than 17%.Moreover,a higher content of c-C4F8 decreases the sensitivity of gas mixtures to an electric field,and this phenomenon is more obvious in CF3I/c-C4F8/CO2 gas mixtures.The synergistic effects for CF3I/c-C4F8/70%N2 were most obvious when the c-C4F8 content was approximately 20%,and for CF3I/c-C4F8/70%CO2 when the c-C4F8 content was approximately 10%.On the basis of this research,CF3I/c-C4F8/70%N2 shows better insulation performance when the c-C4F8 content is in the15%–20%range.For CF3I/c-C4F8/70%CO2,when the c-C4F8 content is in the 10%–15%range,the gas mixtures have excellent performance.Hence,these gas systems might be used as alternative gas mixtures to SF6 in high-voltage equipment.
基金Supported by the National Key Research and Development Plan of China(2017YFC0307306)National Natural Science Foundation of China(51676197,51576197)+2 种基金CAS Program(KGZD-EW-301)Guangzhou Science and Technology Project(201804010411)Youth Innovation Promotion Association CAS
文摘To obtain the fundamental data of CO2/N2 gas mixture hydrate formation kinetics and CO2 separation and sequestration mechanisms,the gas hydrate formation process by a binary CO2/N2 gas mixture(50:50)in fine sediments(150–250μm)was investigated in a semibatch vessel at variable temperatures(273,275,and 277 K)and pressures(5.8–7.8 MPa).During the gas hydrate reaction process,the changes in the gaseous phase composition were determined by gas chromatography.The results indicate that the gas hydrate formation process of the binary CO2/N2 gas mixture in fine sediments can be reduced to two stages.Firstly,the dissolved gas containing a large amount of CO2 formed gas hydrates,and then gaseous N2 participated in the gas hydrate formation.In the second stage,all the dissolved gas was consumed.Thus,both gaseous CO2 and N2 diffused into sediment.The first stage in different experiments lasted for 5–15 h,and>60%of the gas was consumed in this period.The gas consumption rate was greater in the first stage than in the second stage.After the completion of gas hydrate formation,the CO2 content in the gas hydrate was more than that in the gas phase.This indicates that CO2 formed hydrate easily than N2 in the binary mixture.Higher operating pressures and lower temperatures increased the gas consumption rate of the binary gas mixture in gas hydrate formation.
基金supported by the National Natural Science Foundation of China (Grant No. 51006083)the China Postdoctoral Science Foundation (Grant No. 20110491658)the Fundamental Research Funds for the Central Universities
文摘The potential energy snrface of a CO2-N2 mixture is determined by using an inversion method, together with a new collision integral correlation [J. Phys. Chem. R@ Data 19 1179 （1990）]. With the new invert potential, the transport properties of CO2-N2 mixture are presented in a temperature range front 273.15 K to 3273.15 K at low density by employing the Chapman-Enskog scheme and the Wang Chang-Uhlenbeck de Boer theory, consisting of a viscosity coefficient, a thermal conductivity coefficient, a binary diffusion coefficient, and a thermal diffusion factor. The accuracy of the predicted results is estimated to be 2% for viscosity, 5% for thermal conductivity, and 10% for binary diffusion coefficient.
基金supported by National Natural Science Foundation of China(No.10875093)
文摘We calculated the uniform dielectric breakdown field strength of residual 30% CF3I/CO2 gas mixtures during the arc extinction process over the temperature range 300-3500 K at 0.1 MPa. The limiting reduced field strengths are decided by a balance of electron generation and loss based on chemical reactions estimated by the electron energy distribution function （EEDF）, which employs the Boltzmann equation method with two-term expanding approximation in the steady-state Townsend （SST） condition. During the insulation recovery phase, the hot CF3I/CO2 gas mixtures have maximum dielectric strength at a temperature of about 1500 K. At room temperature 300 K, the electric strength after arc extinction （90.3 Td, 1 Td=10-21 V.m2） is only 38% of the original value before arc （234.9 Td）. The adverse insulation recovery ability of CF3I/CO2 gas mixtures in arc extinction hinders its application in electric circuit breakers and other switchgears as an arc quenching and insulating medium.
基金This work was supported by Doctor Foundation of Hebei Education Committee Hebei Natural Science Foundation(599091 ) of China
文摘Monte Carlo simulations are adopted to study the electron motion in the mixture of H2 and CH4 during diamond synthesis via Glow Plasma-assisted Chemical Vapor Deposition (GPCVD). The non-uniform electric field is used and the avalanche of electrons is taken into account in this simulation. The average energy distribution of electrons and the space distribution of effective species such as CH3, CH+3, CH+ and H at various gas pressures are given in this paper, and optimum experimental conditions are inferred from these results.
基金financial support of Research Institute of Petroleum Industry
文摘Highly selective separation of CO_2 from its methane-containing binary gas mixture can be achieved by using Poly(ether-block-amide)(PEBAX)mixed matrix membranes(MMMs).According to FESEM and AFM analyses,silica-based nanoparticles were homogenously integrated within the polymer matrix,facilitating penetration of CO_2 through the membrane while acting as barrier for methane gas.The membrane containing 4.6 wt% fumed silica(FS)(PEBAX/4.6 wt%FS)exhibits astonishing selectivity results where binary gas mixture of CO_2/CH_4 was used as feed gas.As detected by gas chromatography,in the permeate side,data showed a significant increase of CO_2 permeance,while CH_4 transport through the mixed matrix membrane was not detectable.Moreover,PEBAX/4.6 wt%FS greatly exceeds the Robeson limit.According to data reported on CO_2/CH_4 gas pair separation in the literature,the results achieved in this work are beyond those data reported in the literature,particularly when PEBAX/4.6 wt%FS membrane was utilized.
基金Supported by the National Science Fund for Excellent Young Scholars(21422607)Key Program of National Natural Science Foundation of China(91434203)
文摘A series of modifiedγ-Al_2O_3supported iron-based catalysts(M-Fe/γ-Al_2O_3)was developed to reduce SO_2in actual smelter off-gases using CO–H_2gas mixture as reducing agent for sulfur production.Used as modifiers,three metal additives—Ni,Co,and Ce were added to Fe/γ-Al_2O_3catalysts.Changes in catalyst structure and active phase were characterized with X-ray diffraction,XPS,SEM,and EDS.The reduction ability of catalysts was exhibited via CO-TPR.The prepared catalysts only need to be pre-reacted for a period of time,eliminating the need for presulfidation treatment.Reaction conditions were optimized in a fixed bed reactor to achieve high SO_2conversion and sulfur selectivity.XRD characterization was carried out to verify the resulting sulfur products.Combining in situ infrared characterization and catalyst evaluation of support and active component,the reaction mechanism was investigated and proposed.
基金Financially supported by the National Natural Science Foundation of China and the Chinese Corrosion Science Laboratory
文摘The effects of 5 wt.-% Al and 10 wt.-% Al on the sulfidation behaviour of the Fe-25Cralloy in H<sub>2</sub>S-H<sub>2</sub> gas mixtures in the temperature range of 700～900 C has been studied.Thesulfidation resistance of Fe-25Cr was improved and the sulfide scale morphologies,compositionand structure of Fe-25Cr changed remarkably.The sulfidation kinetics of the alloys with alu-minium obeyed basically the parabolic law after an initial period of reaction time.The sulfida-tion mechanism of the Fe-Cr-Al alloy has been proposed.
基金Supported by National Key Technology Research and Development Program(2013BAD11B03)National Natural Science Foundation(31272249,31071865,41505100)~~
文摘This experiment was conducted in Xinxiang, Henan from June 2013 to June 2014. Total four treatments were designed including farmers ’ common practice （F, 250 kg/hm^2）, 80% F （LF, 200 kg/hm^2）, 80% F＋biochar （LFC） and no fertilizer （CK） to measure the dynamic emissions of CO2 and N2O from a summer maize-winter wheat field by static chamber-gas chromatography method. The results showed that the soil CO2 emission was 21.8-1 022.7 mg/（m^2·h）, and was mainly influenced by soil temperature and moisture content. During the growth of summer maize, the soil CO2 emission was more significantly affected by soil moisture con-tent; and in winter wheat growing season, it was more significantly affected by soil temperature in the top 5 cm. The LF and LFC treatments significantly reduced the soil cumulative CO2 emission, especial y during the growth of winter wheat. Fertiliza-tion and irrigation were the main factors influencing the soil N2O emission. The soil N2O emission during the fertilization period accounted for 73.9%-74.5% and 40.5%-43.6% of the soil cumulative N2O emission during the summer maize-and winter wheat-growing season, respectively. The peak of emission fluxes was determined by fertilization amount, while the occurrence time of emission peak and emission re-duction effect were influenced by irrigation. The LF treatment reduced the soil cu-mulative N2O emission by 15.7%-16.8% and 18.1%-18.5% during the growth period of summer maize and winter wheat, respectively. Reduced nitrogen fertilization is an effective way for reducing N2O emission in intensive high-yielding farmland. Under a suitable nitrogen level （200 kg/hm^2）, the application of biochar showed no significant effect on the soil N2O emission in a short term. The N2O emission factors of the L and LF treatments were 0.60% and 0.56%, respectively. ln the intensive high-yield-ing farmland of North China, reducing the nitrogen application amount is an appro-priate measure to mitigate greenhouse gas emissions without crop yield loss.
基金supported by the National Natural Science Foundation of China(Nos.51174127 and 21176145)the Natural Science Foundation of Shandong Province(No.ZR2011DM005)the Open Research Fund Program of Key Laboratory of Mine Disaster Prevention and Control(Shandong University of Science and Technology)(No.MDPC0806)
文摘In order to better understand the prevailing mechanism of CO2 storage in coal and estimate CO2 sequestration capacity of a coal seam and enhanced coalbed methane recovery （ECBM） with CO2 injection into coal, we investigated the preferential adsorption of CH4 and CO2 on coals. Adsorption of pure CO2, CH4 and their binary mixtures on high-rank coals from Qinshui Basin in China were employed to study the preferential adsorption behaviour. Multiple regression equations were presented to predict CH4 equi- librium concentration from equilibrium pressure and its initial-composition in feed gas. The results show that preferential adsorption of CO2 on coals over the entire pressure range under competitive sorption conditions was observed, however, preferential adsorption of CH4 over CO2 on low-volatile bituminous coal from higher CH4-compostion in source gas was found at up to 1O MPa pressure. Preferential adsorp- tion of CO2 increases with increase of CH4 concentration in source gas, and decreases with increasing pressure. Although there was no systematic investigation of the effect of coal rank on preferential adsorp- tion, there are obvious differences in preferential adsorption of gas between low-volatile bituminous coal and anthracite. The obtained preferential adsorption gives rise to the assumption that CO2 sequestration in coal beds with subsequent CO2-ECBM might be an ootion in Qinshui Basins, China.
文摘高压断路器分合闸过程中触头间隙介质的绝缘强度及其变化是断路器结构设计的重要性能指标。搭建高压断路器触头间隙介质绝缘特性实验回路,测量C_(4)F_(7)N/CO_(2)混合气体断路器空载分合闸过程中不同压强、不同C4F7N含量时触头间隙介质的动态击穿电压,研究C_(4)F_(7)N/CO_(2)混合气体断路器的关合预击穿特性和分闸绝缘特性。实验发现,断路器空载分合闸过程中C_(4)F_(7)N/CO_(2)混合气体动态击穿电压存在“低电压击穿”现象;合闸过程中,动态击穿电压分散性较大,C_(4)F_(7)N/CO_(2)混合气体断路器的关合预击穿特性显著劣于SF6断路器,增大压强或增加C4F7N含量对混合气体动态击穿电压分散性的改善不大;正、负极性条件下0.7MPa时9%C_(4)F_(7)N/91%CO_(2)混合气体的分闸平均绝缘强度上升率(rate of rise of dielectric strength,RRDS)分别为49.8kV/ms和42.7kV/ms,具有“反极性”效应;分闸过程中,“低电压击穿”现象主要出现在刚分后2ms(开距约6mm)范围以内,断路器若在此时间(开距)范围内熄弧,极易发生弧后重击穿现象,因此,C_(4)F_(7)N/CO_(2)混合气体断路器结构设计时应避免在此范围内熄弧。
