Effects of initial δ phase(Ni_3Nb) on hot tensile deformation behaviors and material constants of Ni-based superalloy

Effects of initial δ phase（Ni_3Nb） on the hot tensile deformation behaviors and material constants of a Ni-based superalloy were investigated over wide ranges of strain rate and deformation temperature. It is found that the true stress-true strain curves exhibit peak stress at a small strain, and the peak stress increases with the increase of initial δ phase. After the peak stress, initial δ phase promotes the dynamic softening behaviors, resulting in the decreased flow stress. An improved Arrhenius constitutive model is proposed to consider the synthetical effects of initial δ phase, deformation temperature, strain rate, and strain on hot deformation behaviors. In the improved model, material constants are expressed as the functions of the content of initial δ phase and strain. A good agreement between the predicted and measured results indicates that the improved Arrhenius constitutive model can well describe hot deformation behaviors of the studied Ni-based superalloy.

Upsilon Constants and Their Usefulness in Planck Scale Quantum Cosmology

This paper introduces the two Upsilon constants to the reader. Their usefulness is described with respect to acting as coupling constants between the CMB temperature and the Hubble constant. In addition, this paper summarizes the current state of quantum cosmology with respect to the Flat Space Cosmology (FSC) model. Although the FSC quantum cosmology formulae were published in 2018, they are only rearrangements and substitutions of the other assumptions into the original FSC Hubble temperature formula. In a real sense, this temperature formula was the first quantum cosmology formula developed since Hawking’s black hole temperature formula. A recent development in the last month proves that the FSC Hubble temperature formula can be derived from the Stephan-Boltzmann law. Thus, this Hubble temperature formula effectively unites some quantum developments with the general relativity model inherent in FSC. More progress towards unification in the near-future is expected.

Dual laterolog borehole correction based on dynamic tool constants

The positive and negative difference of deep and shallow resisitivity in formation without invasion is caused mainly by the fixed two tool constants from numerical simulations. A dynamic calibration method for tool constants is proposed based on the effects of the mud and formation resisitivity ratio on the two constants calculated using the finite element method （FEM）. Finally, four specific examples are given to validate the dynamic calibration method. It is an automatic borehole correction method and can give more accurate formation resistivity. The method is useful for dual laterolog logging.

Fundamental Physical Constants and Primary Physical Parameters

Every four years the Committee on Data for Science and Technology (CODATA) supplies a self-consistent set of values of the basic constants and conversion factors of physics recommended for international use. In 2013, the World-Universe Model (WUM) proposed a principally different depiction of the World as an alternative to the picture of the Big Bang Model. This article: 1) Gives the short history of Classical Physics before Special Relativity;2) Calculates Fundamental Physical Constants based on experimentally measured Rydberg constant, Electrodynamic constant, Electron Charge-to-Mass Ratio, and Planck constant;3) Discusses Electrodynamic constant and Speed of Light;4) Considers Dimensionless Fundamental Parameters (Dirac Large Number Q and Dimensionless Rydberg Constant α);5) Calculates Newtonian Constant of Gravitation based on the Inter-connectivity of Primary Physical Parameters;6) Makes a detailed analysis of the Self-consistency of Fundamental Physical Constants and Primary Physical Parameters through the prism of WUM. The performed analysis suggests: 1) Discontinuing using the notion “Vacuum” and its characteristics (Speed of Light in Vacuum, Characteristic Impedance of Vacuum, Vacuum Magnetic Permeability, Vacuum Electric Permittivity);2) Accepting the exact numerical values of Electrodynamic constant, Planck constant, Elementary charge, and Dimensionless Rydberg Constant α. WUM recommends the predicted value of Newtonian Constant of Gravitation in 2018 to be considered in CODATA Recommend Values of the Fundamental Physical Constants 2022.

Influence of dopant content on morphology and optical constants of ZnO:Na films by sol-gel method

Undoped and Na-doped ZnO films were deposited by sol-gel method.The effects of sodium incorporation on structure,surface morphology and optical constants of the films were investigated.X-ray diffraction patterns show the hexagonal wurtzite polycrystalline structure and that the sodium incorporation leads to the change in the structural characteristics of ZnO films.The SEM observations show that the surface morphology of the films is affected by the sodium incorporation.The transmission spectra show that the average transmittance of the films is above 85% in the visible range.The absorption edge initially blue-shifts and then red-shifts with the increase of Na doping content.The optical constants of these films were calculated using transmission spectra.Refractive indices of the films in the visible range decrease at first and then increase with increasing Na doping content.

Biaxial tensile properties and elastic constants evaluation of envelope material for airship

This paper presents an experimental study to determine the tensile properties of the envelope fabric Uretek3216L under biaxial cyclic loading.First the biaxial cyclic tests were carefully carried out on the envelope material to obtain the stress-strain data and the corresponding nonlinearity and orthotropy of the material were analyzed. Then for some determination options with different stress ratios the least squares method minimizing the strain terms was used to calculate the elastic constants from the experimental data.Finally the influences of the determination options with different stress ratios and the reciprocal relationship on the elastic constants were discussed.Results show that the orthotropy of the envelope material can be attributed to the unbalanced crimp of their constitutive yarns in warp and weft directions and the elastic constants vary noticeably with the determination options as well as the normalized stress ratios.In real design practice it is more reasonable to use constants determined for specific stress states in particular stress ratios depending on the project＆#39;s needs.Also calculating the structures with two limitative sets of elastic constants instead of using only one set is recommendable in light of the great variety of the constant＆#39;s values.

Simultaneous estimation of aerosol optical constants and size distribution from angular light-scattering measurement signals

The angular light-scattering measurement（ALSM） method combined with an improved artificial bee colony algorithm is introduced to determine aerosol optical constants and aerosol size distribution（ASD） simultaneously. Meanwhile, an optimized selection principle of the ALSM signals based on the sensitivity analysis and principle component analysis（PCA）is proposed to improve the accuracy of the retrieval results. The sensitivity analysis of the ALSM signals to the optical constants or characteristic parameters in the ASD is studied first to find the optimized selection region of measurement angles. Then, the PCA is adopted to select the optimized measurement angles within the optimized selection region obtained by sensitivity analysis. The investigation reveals that, compared with random selection measurement angles, the optimized selection measurement angles can provide more useful measurement information to ensure the retrieval accuracy. Finally,the aerosol optical constants and the ASDs are reconstructed simultaneously. The results show that the retrieval accuracy of refractive indices is better than that of absorption indices, while the characteristic parameters in ASDs have similar retrieval accuracy. Moreover, the retrieval accuracy in studying L-N distribution is a little better than that in studying Gamma distribution for the difference of corresponding correlation coefficient matrixes of the ALSM signals. All the results confirm that the proposed technique is an effective and reliable technique in estimating the aerosol optical constants and ASD simultaneously.

Thickness dependence of the optical constants of oxidized copper thin films based on ellipsometry and transmittance

Thin oxidized copper films in various thickness values are deposited onto quartz glass substrates by electron beam evaporation. The ellipsometry parameters and transmittance in a wavelength range of 300 nm-1000 nm are collected by a spectroscopic ellipsometer and a spectrophotometer respectively. The effective thickness and optical constants, i.e., refractive index n and extinction coefficient k, are accurately determined by using newly developed ellipsometry combined with transmittance iteration method. It is found that the effective thickness determined by this method is close to the physical thickness and has obvious difference from the mass thickness for very thin film due to variable density of film. Furthermore, the thickness dependence of optical constants of thin oxidized Cu films is analyzed.

Proton radiation effects on optical constants of Al film reflector

The Al film reflectors can yield a high-reflectance over a broad wavelength region, and have been widely used in the spacecraft optical instruments for high quality optical applications. Under the irradiation of charged particles in the Earth radiation belt, the reflectors could be deteriorated. In order to reveal the deterioration mechanism, the change in optical constants of Al film reflector induced by proton radiation with 60 keV was studied in an environment of vacuum with heat sink. Experimental results showed that when the radiation damage primarily occurs in the Al reflecting film, the extinction coefficient k will gradually decrease with increasing radiation fluence, which results in the decrease of the energies of reflective light. Therefore, the proton radiation induced an obvious degradation of spectral reflectance in the wavelength region from 200 to 800nm on the Al film reflector.

Ground state parameters,electronic properties and elastic constants of CaMg3:DFT study

The present study aims to investigate the equation of state(EOS)parameters of CaMg3 in aReCh(D09),AIFR(DO3),CU3A11(LI2)and CuTi3(L60)structures,using full potential linear muffin-tin orbitals(FP-LMTO)approach based on the density functional theory(DFT).The local density approximation(LDA)and the generalized gradient approximation(GGA)were both applied for the exchange-correlation potential term.The calculated equation of slate parameters at equilibrium,in general,agreed well with the available data of the literature.The calculations showed that under compression CaMg3 transforms from DO3 to DO9 at about 29.96GPa,and 25.1 GPa using LDA and GGA,respectively.The elastic constants C,y,aggregate moduli,Vickers hardness,sound velocity,and Debye temperature of CaMg3 in D03 structure were also reported,discussed and analyzed.Using LDA(GGA),the calculated values of Hv andθD were found at around 5.80GPa(5.93GPa)and 393.44 K(389.91 K),respectively.Electronic band structure,total density of states(TDOS)as well as the partial density of states(PDOS)have been also obtained.The electronic band structure confirms the metallic behavior of CaMg3 in DO3 phase,the valence bands are dominated by the maximum contribution of‘d’like states of Ca in the energy ranging from 2 to 3 eV for GGA,and from 4.5 to 5 eV for LDA,respectively.

TOPOLOGICAL STRUCTURE OF RENORM ALIZATION CONSTANTS I N QUANTUM FIELD THEORY AT SHORT DISTANCE KUNMING COLLABRATION OF MULTIHADRON DYNAMIOS

The anomalous dimensions of the quantum fields are the Hausdorff dimensiongrad. The present candidate of the renormalization constant is the generalized Cantor discontinuum. The Hausdorff dimensiongrad of the Minkowski space time is based upon the point set with σ-length on light cone.

THE INTRINSIC ACIDITY CONSTANTS AND SPECIFIC SURFACE AREA OF MARINE SOLID PARTICLES I. A NEW METHOD

This paper proposes a new method for determining the intrinsic acidity constants K and K The new method is a great improvement over the modified Langmuir plot method generally adopted in that determination of these constants is not dependent on the specific surface area S of the marine solid particles. The new method was used to determine K, K and S for the main inorganic components of marine solid particles, including illite, montmorillonite, kaolinite, goethite, y-AlOOH. amorphous ferric oxide, MnO2, manganite, SiO 2 and calcium carbonate, and can facilitate the study on the effect of solution constituents, solution temperature, ionic strength, etc. on the value

Key Role of Some Specific Occupied Molecular Orbitals of Short Chain n-Alkanes in Their Surface Tension and Reaction Rate Constants with Hydroxyl Radicals: DFT Study

Basing on the DFT calculations we propose the new theoretical model which describes both the surface tension σ of the short chain n-alkanes at their normal boiling points and their reaction rate constants with hydroxyl radicals OH• (at 297 ± 2 K) on the basis of their molecular orbital electronic characteristics. It has been shown that intermolecular dispersion attraction within the surface liquid monolayer of these compounds, as well as their reaction rate constants k with OH• radicals are determined by the energies Eorb of the specific occupied molecular orbitals which are the same in the determination of both the above physico-chemical characteristics of the studied n-alkanes. The received regression equations confirm the theoretically found dependences between the quantities of σ and k and the module |Eorb|. For the compounds under study this fact indicates the key role of their electronic structure particularities in determination of both the physical (surface tension) and the chemical (reaction rate constants) properties.

Magnesium (II) Adsorption from Aqueous Solutions on China Clay and the Stability Constants for Complex Formation

China clay was employed as an adsorbent for the removal of Mg 2+ from water at pH 7.0 within the temperature range of 303～328 K. The linearity of the plots indicated Langmuir type isotherms. The reaction was exothermic. A maximum removal of 35% was obtained at 0.50 mmol L -1 metal concentration and a pH of 7.0 at 303 K. The H + rel /Mg 2+ ads ratio changed from a fractional value to 2.5. Strong chemical bondings took place between oxygen atom of the surface and Mg 2+ , resulting in a surface complex species. Temperature had a significant effect on H + rel , and the stability constants also increased with increasing temperature.

Prediction of Henry Constants and Adsorption Mechanism of Volatile Organic Compounds on Multi-Walled Carbon Nanotubes by Using Support Vector Regression

Support vector regression （SVR） combined with particle swarm optimization for its parameter optimization is employed to establish a model for predicting the Henry constants of multi-walled carbon nanotubes （MWNTs） for adsorption of volatile organic compounds （VOCs）. The prediction performance of SVR is compared with those of the model of theoretical linear salvation energy relationship （TLSER）. By using leave-one-out cross validation of SVR test Henry constants for adsorption of 35 VOCs on MWNTs, the root mean square error is 0.080, the mean absolute percentage error is only 1.19~, and the correlation coefficient （R2） is as high as 0.997. Compared with the results of the TLSER model, it is shown that the estimated errors by SVR are ali smaller than those achieved by TLSER. It reveals that the generalization ability of SVR is superior to that of the TLSER model Meanwhile, multifactor analysis is adopted for investigation of the influences of each molecular structure descriptor on the Henry constants. According to the TLSER model, the adsorption mechanism of adsorption of carbon nanotubes of VOCs is mainly a result of van der Waals and interactions of hydrogen bonds. These can provide the theoretical support for the application of carbon nanotube adsorption of VOCs and can make up for the lack of experimental data.

First-principles study of the elastic constants and optical properties of uranium metal

We perform first-principles calculations of the lattice constants, elastic constants, and optical properties for alpha- and gamma-uranium based on the ultra-soft pseudopotential method. Lattice constants and equilibrium atomic volume are consistent pretty well with the experimental results. Some difference exists between our calculated elastic constants and the experimental data. Based on the satisfactory ground state electronic structure calculations, the optical co ductivity, dielectric function, refractive index, and extinction coefficients are also obtained. These calculated optical properties are compared with our results and other published experimental data.

Rate Constants for the Reactions of NO_3~.and SO_4^(._) Radicals with Oxalic Acid and Oxalate Anions in Aqueous Solution

Rate constants for the reactions of NO3 and SO4 radicals with oxalic acid and oxalate anions in aqueous solution have been measured using pulse radiolysis and laser flash photolysis.

Elastic Constants of Superconducting MgB2 from Molecular Dynamics Simulations with Shell Model

The elastic constants of superconducting MgB2 are calculated using a molecular dynamics method (MD)with shell model. The lattice parameters, five independent elastic constants, equations of state (EOS), Debye temperature, and bulk modulus of MgB2 are obtained. Meanwhile, the dependence of the bulk modulus B, the lattice parameters a and c, and the unit cell volume V on the applied pressure are presented. It is demonstrated that the method introduced here can well reproduce the experimental results with a reasonable accuracy.

Determination of Formation Constants of Co￣(2+), Ni￣(2+),Cu￣(2+) and Zn￣(2+) Complexes with Humic and Fulvic Acidsby Potentiometric Titration Method

The formation constants of Co￣(2+), Ni￣(2+), Cu￣(2+) and Zn￣(2+) complexes with humic acid (HA) and fulvicacid (FA) in red soil were determined by the potentiometric titration method. The constants as a functionof composition of the complexation solutions were obtained by two graphical approaches respectively Theformation constants decreased with increasing concentration of metal in the solution. The results provideunambiguous evidence for the heterogeneity of the function groups of humic substances. The formationconstants of FA were much smaller than those of HA, and the formation constants of Cu￣(2+) were muchgreater than those of Co￣(2+) , Ni￣(2+) and Zn￣(2+) . The potentiometric titration method for determining formationconstants are also discussed in the article.

A new mixed scheme based on variation of constants for Sobolev equation with nonlinear convection term

A new mixed scheme which combines the variation of constants and the H1-Galerkin mixed finite element method is constructed for nonlinear Sobolev equation with nonlinear con- vection term. Optimal error estimates are derived for both semidiscrete and fully discrete schemes. Finally, some numerical results are given to confirm the theoretical analysis of the proposed method.