Large quantity of fine Ti（C,N） particles, 15-30 nm in size, were observed in low carbon hot strips added to a small amount of Ti and produced by CSP process. The results showed that the precipitation of Ti（C,N） mo...Large quantity of fine Ti（C,N） particles, 15-30 nm in size, were observed in low carbon hot strips added to a small amount of Ti and produced by CSP process. The results showed that the precipitation of Ti（C,N） mostly took place during soaking and hot rolling, which is significantly different from that in the conventional production. These fine Ti carbonitride particles could be very effective on the austenite grain refinement by hindering grain growth of recrystallized austenite. Their precipitation behavior was discussed and compared with that of the steels produced in the conventional production.展开更多
Transmission electron microscopy （TEM） and physics-chemical phase analysis were employed to investigate the precipitates in high strength steels microalloyed with Ti produced by compact strip production （CSP）. It ...Transmission electron microscopy （TEM） and physics-chemical phase analysis were employed to investigate the precipitates in high strength steels microalloyed with Ti produced by compact strip production （CSP）. It was seen that precipitates in Ti microalloyed steels mainly included TiN, Ti4C2S2, and TiC. The size of TiN particles varied from 50 to 500 nm, and they could precipitate during or before soaking. The Ti4C2S2 with the size of 40-100 nm might precipitate before rolling, and the TiC particles with the size of 5-50 nm precipitated heterogeneously. High Ti content would lead to the presence of bigger TiC particles that precipitated in austenite, and by contrast, TiC particles that precipitated in ferrite and the transformation of austenite to ferrite was smaller. They were less than 30 nm and mainly responsible for precipitate strengthening. It should be noted that the TiC particles in higher Ti content were generally smaller than those in the steel with a lower Ti content.展开更多
Cold-rolled steel sheets in automotive applications require an excellent deep draw ability, which is characterized by the Lankford value （r-value）. In this study, a correlation was identified between r-value and pan...Cold-rolled steel sheets in automotive applications require an excellent deep draw ability, which is characterized by the Lankford value （r-value）. In this study, a correlation was identified between r-value and pancake-shaped grain flatness which is indicated as the ratio of grain diameter in the rolling direction （RD） and normal direction （ND） of sheets （dr/dn）. A mathematical model （ r = e^0.345（dn^1/2-dr^1/2） ） was developed to calculate r-value by the microstructure of steel sheets hot-rolled by compact strip production （CSP）. It is shown that the r-value is higher, if the microstructure of steel sheet is of pancake-shaped grains elongated in the rolling direction. The calculated r-value is confirmed to fit exactly to the measured one from the large-scale production.展开更多
In comparison with conventional production for hot strips, compact strip production (CSP) brings about some new micro-structural phenomena. Investigations were carried out to clarify the grain refinement mechanism of ...In comparison with conventional production for hot strips, compact strip production (CSP) brings about some new micro-structural phenomena. Investigations were carried out to clarify the grain refinement mechanism of low carbon steel strips produced by the EAF-CSP process. Samples, obtained from the same rolling stock during continuous rolling, were examined through SEM, TEM and XEDS. Thin slabs have a dominant columnar structure and the spacing of the secondary dendrite arms ranges from 90 to -125 μm. The average grain sizes for the central area of the samples from the 1st to 6th pass are 41.6, 25.2, 21.4, 20.2, 13.1, 6.7 μm, respectively. Large number of nanometer oxide and sulfide have been found in the low carbon steel produced by the CSP process. The grain refinement mechanism can be summarized as follows: finer solidification structure of the thin slab; austenite recrystalliza-tion at higher temperature and stain accumulation at lower temperature caused by the great reduction of single rolling pass during continuous rolling; nano-scaled precipitates of sulfide and oxide which drag grain boundaries of austenite or ferrite to prevent the grain coarsening.展开更多
基金This work was financially supported by the National Natural Science Foundation of China (No.50371009)
文摘Large quantity of fine Ti（C,N） particles, 15-30 nm in size, were observed in low carbon hot strips added to a small amount of Ti and produced by CSP process. The results showed that the precipitation of Ti（C,N） mostly took place during soaking and hot rolling, which is significantly different from that in the conventional production. These fine Ti carbonitride particles could be very effective on the austenite grain refinement by hindering grain growth of recrystallized austenite. Their precipitation behavior was discussed and compared with that of the steels produced in the conventional production.
文摘Transmission electron microscopy （TEM） and physics-chemical phase analysis were employed to investigate the precipitates in high strength steels microalloyed with Ti produced by compact strip production （CSP）. It was seen that precipitates in Ti microalloyed steels mainly included TiN, Ti4C2S2, and TiC. The size of TiN particles varied from 50 to 500 nm, and they could precipitate during or before soaking. The Ti4C2S2 with the size of 40-100 nm might precipitate before rolling, and the TiC particles with the size of 5-50 nm precipitated heterogeneously. High Ti content would lead to the presence of bigger TiC particles that precipitated in austenite, and by contrast, TiC particles that precipitated in ferrite and the transformation of austenite to ferrite was smaller. They were less than 30 nm and mainly responsible for precipitate strengthening. It should be noted that the TiC particles in higher Ti content were generally smaller than those in the steel with a lower Ti content.
文摘Cold-rolled steel sheets in automotive applications require an excellent deep draw ability, which is characterized by the Lankford value （r-value）. In this study, a correlation was identified between r-value and pancake-shaped grain flatness which is indicated as the ratio of grain diameter in the rolling direction （RD） and normal direction （ND） of sheets （dr/dn）. A mathematical model （ r = e^0.345（dn^1/2-dr^1/2） ） was developed to calculate r-value by the microstructure of steel sheets hot-rolled by compact strip production （CSP）. It is shown that the r-value is higher, if the microstructure of steel sheet is of pancake-shaped grains elongated in the rolling direction. The calculated r-value is confirmed to fit exactly to the measured one from the large-scale production.
文摘In comparison with conventional production for hot strips, compact strip production (CSP) brings about some new micro-structural phenomena. Investigations were carried out to clarify the grain refinement mechanism of low carbon steel strips produced by the EAF-CSP process. Samples, obtained from the same rolling stock during continuous rolling, were examined through SEM, TEM and XEDS. Thin slabs have a dominant columnar structure and the spacing of the secondary dendrite arms ranges from 90 to -125 μm. The average grain sizes for the central area of the samples from the 1st to 6th pass are 41.6, 25.2, 21.4, 20.2, 13.1, 6.7 μm, respectively. Large number of nanometer oxide and sulfide have been found in the low carbon steel produced by the CSP process. The grain refinement mechanism can be summarized as follows: finer solidification structure of the thin slab; austenite recrystalliza-tion at higher temperature and stain accumulation at lower temperature caused by the great reduction of single rolling pass during continuous rolling; nano-scaled precipitates of sulfide and oxide which drag grain boundaries of austenite or ferrite to prevent the grain coarsening.
