Promoted catalytic property of Cu/SSZ-13 by introducing a minority of Mn for NO removal from diesel engine exhaust

The Cu-exchanged SSZ-13 with the small-pore chabazite framework is considered as a highly efficient catalyst for selective catalytic reduction of NO with NH_(3)(NH_(3)-SCR).In order to further improve the catalytic property,a series of Mn ion-assisted Cu/SSZ-13 powder catalysts were prepared by co-exchange method and stepwise exchange method.It is found that the NH_(3)-SCR activity,N_(2) selectivity,hydrothermal stability and sulfur resistance of Cu/SSZ-13 are promoted by introducing a minority of Mn(0.15%to 0.23%(mass))through co-exchange method.Characterization results reveal that the Cu,Mn co-exchange enables the higher amounts of Cu^(2+)active sites,the abundant medium strong and strong acid,the optimized ratio of Lewis acid to Brønsted acid etc.,which are required for a good NH_(3)-SCR catalytic property over broad temperature range and under harsh working environment.Moreover,a monolithic catalyst was prepared by impregnating a cordierite ceramic support into the coating slurry containing the optimized CuMn/SSZ-13 powder.The diesel engine bench tests show that Cu,Mn co-exchange gives the monolith catalyst a better catalytic property than commercial catalysts.This work provides an important guidance for the rational design of secondary-ion-assisted zeolites applied in NH_(3)-SCR.

Dynamic Regulation of Hydrogen Bonding Networks and Solvation Structures for Synergistic Solar‑Thermal Desalination of Seawater and Catalytic Degradation of Organic Pollutants

Although solar steam generation strategy is efficient in desalinating seawater,it is still challenging to achieve continuous solar-thermal desalination of seawater and catalytic degradation of organic pollutants.Herein,dynamic regulations of hydrogen bonding networks and solvation structures are realized by designing an asymmetric bilayer membrane consisting of a bacterial cellulose/carbon nanotube/Co_(2)(OH)_(2)CO_(3)nanorod top layer and a bacterial cellulose/Co_(2)(OH)_(2)CO_(3)nanorod(BCH)bottom layer.Crucially,the hydrogen bonding networks inside the membrane can be tuned by the rich surface–OH groups of the bacterial cellulose and Co_(2)(OH)_(2)CO_(3)as well as the ions and radicals in situ generated during the catalysis process.Moreover,both SO_(4)^(2−)and HSO_(5)−can regulate the solvation structure of Na^(+)and be adsorbed more preferentially on the evaporation surface than Cl^(−),thus hindering the de-solvation of the solvated Na^(+)and subsequent nucleation/growth of NaCl.Furthermore,the heat generated by the solar-thermal energy conversion can accelerate the reaction kinetics and enhance the catalytic degradation efficiency.This work provides a flow-bed water purification system with an asymmetric solar-thermal and catalytic membrane for synergistic solar thermal desalination of seawater/brine and catalytic degradation of organic pollutants.

Research on the Construction of Intellectual Property System and Optimization of Business Environment in China

With the rapid development of globalization and information technology,intellectual property has been one of the key drivers of economic growth,and the construction of intellectual property system has become an important criterion for measuring the quality of business environment.This article is intended to explore the current status of intellectual property system construction in China,the challenges,and its relationship with the business environment,to propose the corresponding countermeasures and suggestions.The study finds that the legal system of intellectual property in China is gradually improving,and judicial and administrative protection are continuously strengthened.However,the challenges still remain such as frequent infringements,rights hard to protect and insufficient international cooperation.These issues not only affect the legitimate rights and interests of innovation entities,but also for the market fairness and the level of the business environment.Therefore,this article proposes that strengthening the perfection of the intellectual property legal system,enhancing intellectual property services and support capabilities,strengthening international cooperation and exchanges,and accelerating the cultivation of composite talents.It aims to provide theoretical references for the construction of intellectual property system and the optimization of the business environment,promote the high-quality development of economy and enhance the global competitiveness of the country.

Modified-EISA synthesis of mesoporous high surface area CeO_2 and catalytic property for CO oxidation

Mesoporous CeO2 particles with high surface area were synthesized using a modified evaporation-induced self assembly(EISA) method which combined citric acid as complexing agent.As-prepared powder and further thermal treatment samples were characterized by X-ray diffraction(XRD),transmission electron microscopy(TEM),selected area electron diffraction(SAED),Fourier transform infrared spectrometer(FTIR),thermogravimetry and differential thermal analysis(TG-DTA),Brunauer-Emmett-Teller(BET) and Barrett-Joyner-Ha...

A Novel 3D Metal Coordination Polymer Based on Tetranuclear Cobalt Cluster Building Blocks:Synthesis,Crystal Structure and Photocatalytic Property

A novel 3D MCP,[Co;（μ;-OH）(btc)（bmip）];(1,H;btc=1,3,5-benzenetricarboxylate acid,bmip=1,3-bis（2-methylimidazolyl）propane),was synthesized under hydrothermal conditions and characterized by single-crystal X-ray diffraction,powder XRD,FT-IR,TGA and elemental analysis techniques.MCP 1 features a 3D framework based on tetranuclear Co（Ⅱ）clusters where the four cobalt ions are coplanar,and shows an unusual binodal（3,10）-connected topology.Furthermore,the photocatalytic experiment result indicates the degradation ratios of rhodamine B（RhB）reach 78.2%when MCP 1 acts as catalyst.

Effects of ultrasonic impregnation combined with calcination in N_2 atmosphere on the property of Co_3O_4/CeO_2 composites for catalytic methane combustion

CoO/CeOcomposites with high surface areas and ultrafine crystalline sizes for catalytic combustion of methane were firstly prepared by a new sol-gel method which combined ultrasonic impregnation treatment and calcination in Natmosphere. The samples were characterized by various means such as nitrogen adsorption/desorption, X-ray diffraction(XRD), Htemperature-programmed reduction(H-TPR),X-ray photoelectron spectroscopy(XPS) and transmission electron microscopy(TEM). Results showed that the modified catalyst had the mesoporous structure, comparatively higher amount of surface oxygen and larger oxygen vacancies than others. As a result of the structure and surface composition merits, a high methane combustion conversion(50%) could be obtained at a low temperature of 262 °C for the modified CoO/CeOcomposites catalysts. The experimental results demonstrated that ultrasonic impregnation treatment combined with the Nthermal treatment prior to calcination in air had a promising application for preparation of CoO/CeOcomposites catalysts for low-temperature catalytic combustion of methane.

Syntheses and catalytic performances of three coordination polymers with tetracarboxylate ligands

Three zincand cobaltcoordination polymers,namely{[Zn_(2)(μ_(6)-adip)(phen)_(2)]·4H_(2)O}_(n)(1),{[Co_(2)(μ_(6)-adip)(bipy)_(2)]·4H_(2)O}_(n)(2),and[Co_(2)(μ4-adip)(μ-bpa)_(2)]_(n)(3)have been constructed hydrothermally using H4adip(H4adip=5,5′-azanediyldiisophthalic acid),phen(phen=1,10-phenanthroline),bipy(bipy=2,2′-bipyridine),bpa(bpa=bis(4-pyridyl)amine),and zinc and cobalt chlorides at 160℃.The products were isolated as stable crystalline solids and were characterized by IR spectra,elemental analyses,thermogravimetric analyses,and single-crystal X-ray diffrac-tion analyses.Single-crystal X-ray diffraction analyses revealed that three compounds crystallize in the orthorhom-bic system Pnna(1 and 2)or P21212(3)space groups.All compounds exhibit 3D frameworks.The catalytic perfor-mances in the Henry reaction of these compounds were investigated.Compound 3 exhibited an effective catalytic activity in the Henry reaction at 70℃.CCDC:2339391,1;2339392,2;2339393,3.

Syntheses,crystal structures,and catalytic properties of three zinc(Ⅱ),cobalt(Ⅱ)and nickel(Ⅱ)coordination polymers constructed from 5⁃(4⁃carboxyphenoxy)nicotinic acid

Three zinc(Ⅱ),cobalt(Ⅱ),and nickel(Ⅱ)coordination polymers,namely[Zn(μ^(3-)cpna)(μ-dpea)_(0.5)]_(n)(1),[Co(μ^(3-)cpna)(μ-dpey)_(0.5)]_(n)(2),and[Ni(μ^(3-)cpna)(μ-dpey)_(0.5)(H_(2)O)]_(n)(3),have been constructed hydrothermally using H_(2)cpna(5-(4-carboxyphenoxy)nicotinic acid),dpea(1,2-di(4-pyridyl)ethane),dpey(1,2-di(4-pyridyl)ethylene),and zinc,cobalt,and nickel chlorides at 160℃.The products were isolated as stable crystalline solids and were characterized by IR spectra,elemental analyses,thermogravimetric analyses,and single-crystal X-ray diffraction analyses.Single-crystal X-ray diffraction analyses revealed that three compounds crystallize in the triclinic system,space group P1.Compounds 1-3 show 2D layer structures.The catalytic activities in the Knoevenagel condensation reaction of these compounds were investigated.Compounds 1 and 2 exhibit effective catalytic activities in the Knoevenagel condensa-tion reaction at room temperature.For this reaction,various parameters were optimized,followed by the investiga-tion of the substrate scope.CCDC:2335676,1;2335677,2;2335678,3.

A New Property of Conjugated Polymer PFP: Catalytic Degradation of Methylene Blue Aqueous Solution

A new property of conjugated polymer poly（furancarbinol-co-phenol）（PFP） was studied. The target copolymer was used as a catalyst after proper heating treatment. And dye methylene blue （MB） could be fully degraded and largely mineralized on PFP, under natural light or even in dark, in a few minutes. Furthermore, the catalytic activity could be preserved after several runs and the catalyst was readily separated. The effect of calcination temperature was also observed.

Ionothermal Synthesis, Crystal Structure and Photocatalytic Property of a New Cobalt Coordination Polymer

The reaction of flexible bis（imidazole） ligand and 1,2-bis（imidazol-l＇-yl）methane （bimm） with Co（Ⅱ） salt under ionothermal method resulted in the formation of a new coordination polymer {[Co（bimm）3]·（PF6）2}n （1）. X-ray single-crystal diffraction determination reveals that 1 crystallizes in the triclinic Pi space group, with α = 8.647（6）, b = 12.092（9）, c = 14.967（1 l） A, α = 88.912（8）, β = 81.199（8）, ）, = 89.395（8）°, V= 1546 （2） A3, Z = 2, Mr = 793.39, Dc= 1.704 Mg/m3,μ = 0.768 mm-1 F（000） = 798, the final R = 0.0626 and wR = 0.1634 for 4319 observed reflections with I〉 2σ（I）. In compound 1, the Co（lI） ion is connected to another Co（ll） by two bimm ligands to form 1D double chains which are further linked by bimm ligands to form a 2D wavelike layer. Topologically, the structure of 1 represents a uninodal 2D 4-connected sq1/Shubnikov tetragonal plane net. Moreover, thermogravimetric analyses and photocatalytic property for 1 have also been investigated.

SYNTHETIC AND CATALYTIC PROPERTY STUDIES ON SILICA SUPPORTED BIS-(ACETYLACETONATO) COBALT(Ⅱ) COMPLEXES^(**)

This paper reports mainly the preparation of silica supported acetylacetone ligands and their cobalt complexes, the characterization of their chemical structure, and the evaluation of their catalytic activity in the reaction for the preparation of ethers directly from alkanols and benzyl chloride. The results indicate that those silica supported β-diketone cobalt complexes (SACO) not only can simplify the reaction procedure of the ether preparation but also show a much higher catalytic activity in comparison with other homogeneous catalysts. In addition, SACO can be recovered and reused although their catalytic activity descend gradually as a result of the decrease in their cobalt content.

Synthesis and Photocatalytic Property of the ZrO_2/TiO_2 Pillared Laponite

The ZrO2/TiO2 pillared laponite （Ti-Zr-lap） photocatalysts were prepared with intercalation reaction by supercritical fluid drying （SCFD）,and characterized by XRD,TEM,SEM and BET surface area analysis,and the photocatalytic properties of Ti-Zr-lap were investigated by degradation of azo dye acid red B （ARB）.The results showed that the ZrO2/TiO2 pillared structures in laponite could be formed,with the mass fraction of （Zr4＋＋Ti4＋）/laponite （Xm） increasing,the basal spacing and the BET surface area of Ti-Zr-lap significantly increased.The Ti-Zr-lap used as photocatalyst had the advantages of stable and porous layered structure,large surface area with the anatase type TiO2.Compared with the Ti-Zr-lap dried by air drying,the Ti-Zr-lap dried by SCFD showed better photocatalytic property which was very close to that of P25 TiO2.Using the Ti-Zr-lap as photocatalyst with the optimum Xm of 0.16 and the calcination temperature of 500 ℃,under the conditions of the initial concentration of ARB 20 mg/L,photocatalyst concentration of 1.5 g/L and irradiation time 60 min,the decoloring rate of ARB could achieve 98.3%,indicating that the Ti-Zr-lap had excellent photocatalytic property.

Study on Property of Salicylaldehyde Schiff Base Metal Complexes for Catalytic Oxidation of Model Sulfides

Seven kinds of Schiff base metal complexes(C1-C7)were synthesized by the reaction of substituted salicylaldehyde Schiff base with cobalt nitrate,nickel nitrate,and copper nitrate,respectively.The oxygen carrying performance,and the catalytic property of complexes for the oxidation of model sulfides 1-hexanethiol,dibutyl sulfide,and 2-methylthiophene along with their influencing factors were explored,while the oxidized products of the model sulfides were also analyzed and characterized.The results show that the catalytic oxidation property of the complexes is determined by their oxygen carrying performance and solubility in n-octane.The oxygen carrying performance of the complexes is mainly affected by the central ion species,the electronic effects,and the spatial effects of the substituents as well as the degree of conjugation.More specifically,the oxygen carrying performance can be improved by enhancing the oxygenation capacity of the central metal ions,increasing the electron donating ability of the ligand substituent,and diminishing the steric hindrance as well as extending the conjugated chain.Complexes C7 were found to be with high oxygen carrying capacity and high solubility in n-octane,which shows the best catalytic oxidation property,and the oxidation conversion rates for 1-hexylthiol,dibutyl sulfide,and 2-methylthiophene are 74.2%,65.1%,and 22.7%,respectively.Upon using the oxidation catalyst of Schiff base metal complexes,three sulfides can be oxidized by oxygen to form sulfones and sulfoxides.1-Hexanethiol and dibutyl sulfide will continue to be oxidized to form sulfates and sulfites.

Electron Donating Property and Catalytic Activity ofPerovskite-type Mixed Oxides (ABO_3) Consisting of Rare Earth and 3d Transition Metals

The catalytic activity of Perovskite-type mixed oxides (LaCoO3, PrCoO3 and SmCoO3) for the reduction of cyclohexanone to cyclohexanol with 2-propanol (Meerwein-PonndorfVerley reduction) has been studied. The data have been correlated with the surface electron donor properties of these mixed oxides

THE CORRELATION BETWEEN ZrO_2 PHASE AND ITS CATALYTIC PROPERTY

In this letter, the preparation of three ZrO2 phases has beed briefly described and their catalytic results have been presented for CO hydrogenation to olefin. These catalysts had a good selectivity for light olefin. Monoclinic ZrO2 catalyst had a high selectivity for isobutene, while the other phase catalysts had not

Mn_(x)Co_(3-x)O_(4)Microtubules with Enhanced Catalytic Activity Towards Toluene Combustion:Effects of Redox Property and Oxygen Species

The redox property and oxygen species play an important role in the catalytic oxidation of volatile organic compounds(VOCs).In this paper,a series of Mn_(x)Co_(3-x)O_(4)catalysts with tubular structure were synthesized and applied for the catalytic combustion of toluene.Various characterization technologies were employed to reveal the relationship between the catalytic performance of the Mn_(x)Co_(3-x)O_(4)catalysts and Mn doping.The results of XRD,SEM and N2 adsorption-desorption analyses showed that the Mn doping had significant effects on the structure and morphology of the Mn_(x)Co_(3-x)O_(4)catalysts.The H2-TPR,O2-TPD,and XPS results proved that the strong interaction between Co and Mn resulted in the enhanced Olatt mobility,the richer active oxygen species,and the enhanced redox property in comparison with the pure Co_(3)O_(4)sample,which were crucial to the improvement of the catalytic activity of Co-Mn catalysts.The best catalyst,Co5-Mn5 sample,exhibited a good and stable activity to catalytically oxidize toluene at low temperatures even in the presence of water vapor,indicating that it is a potential material to be used in the commercialization of catalytic abatement of toluene.

Synthesis of Hierarchical TS-1 and Its Recycling Catalytic Property for Oxidative Desulfurization

Because of its unique pore structure,good hydrothermal stability and high specific surface area,hierarchical TS-1 zeolite(HTS-1)has become an important catalyst for the deep oxidative desulfurization of fuel oils.In this work,HTS-1 has been successfully synthesized by a hydrothermal crystallization method using the C-SiO_(2)composite as both silicon source and mesoporous template,tetrapropylammonium hydroxide as microporous template,and tetrabutylorthotitanate as titanium source.The C-SiO_(2)composite is obtained by mild carbonization of the SiO_(2)/T-40(Tween 40)xerogel,which is prepared by the two step sol-gel method.The reaction conditions for the oxidative desulfurization(ODS)of dibenzothiophene(DBT)and 4,6-dimethyldibenzothiophene(4,6-DMDBT)over HTS-1 are optimized systematically,and the recycling performances of HTS-1 are investigated in detail.After the 15th run,HTS-1 still maintains high DBT conversion(90.6%)and 4,6-DMDBT conversion(86.0%)without deactivation.The samples before and after recycle tests are characterized by XRD,FT-IR,CHN analysis,UV-Vis and SEM techniques.The results indicate that the crystal structure and morphology of regenerated HTS-1 samples are well kept,which accounts for the good structural stability and reusability of HTS-1.In addition,active intermediates for the ODS of bulky organic sulfides over HTS-1,i.e.,Ti-peroxo(Ti-OOtBu)species,are captured by the UV-Vis technique.Finally,a possible reaction mechanism for the ODS process over HTS-1 is proposed.

Deformable Catalytic Material Derived from Mechanical Flexibility for Hydrogen Evolution Reaction

Deformable catalytic material with excellent flexible structure is a new type of catalyst that has been applied in various chemical reactions,especially electrocatalytic hydrogen evolution reaction(HER).In recent years,deformable catalysts for HER have made great progress and would become a research hotspot.The catalytic activities of deformable catalysts could be adjustable by the strain engineering and surface reconfiguration.The surface curvature of flexible catalytic materials is closely related to the electrocatalytic HER properties.Here,firstly,we systematically summarized self-adaptive catalytic performance of deformable catalysts and various micro–nanostructures evolution in catalytic HER process.Secondly,a series of strategies to design highly active catalysts based on the mechanical flexibility of lowdimensional nanomaterials were summarized.Last but not least,we presented the challenges and prospects of the study of flexible and deformable micro–nanostructures of electrocatalysts,which would further deepen the understanding of catalytic mechanisms of deformable HER catalyst.

Recent advances in cobalt phosphide-based materials for electrocatalytic water splitting:From catalytic mechanism and synthesis method to optimization design

Electrochemical water splitting has long been considered an effective energy conversion technology for trans-ferring intermittent renewable electricity into hydrogen fuel,and the exploration of cost-effective and high-performance electrocatalysts is crucial in making electrolyzed water technology commercially viable.Cobalt phosphide(Co-P)has emerged as a catalyst of high potential owing to its high catalytic activity and durability in water splitting.This paper systematically reviews the latest advances in the development of Co-P-based materials for use in water splitting.The essential effects of P in enhancing the catalytic performance of the hydrogen evolution reaction and oxygen evolution reaction are first outlined.Then,versatile synthesis techniques for Co-P electrocatalysts are summarized,followed by advanced strategies to enhance the electrocatalytic performance of Co-P materials,including heteroatom doping,composite construction,integration with well-conductive sub-strates,and structure control from the viewpoint of experiment.Along with these optimization strategies,the understanding of the inherent mechanism of enhanced catalytic performance is also discussed.Finally,some existing challenges in the development of highly active and stable Co-P-based materials are clarified,and pro-spective directions for prompting the wide commercialization of water electrolysis technology are proposed.

Catalytic effect in lithium metal batteries: From heterogeneous catalyst to homogenous catalyst

Lithium metal batteries are regarded as prominent contenders to address the pressing needs owing to the high theoretical capacity.Toward the broader implementation,the primary obstacle lies in the intricate multi-electron,multi-step redox reaction associated with sluggish conversion kinetics,subsequently giving rise to a cascade of parasitic issues.In order to smooth reaction kinetics,catalysts are widely introduced to accelerate reaction rate via modulating the energy barrier.Over past decades,a large amount of research has been devoted to the catalyst design and catalytic mechanism exploration,and thus the great progress in electrochemical performance has been realized.Therefore,it is necessary to make a comprehensive review toward key progress in catalyst design and future development pathway.In this review,the basic mechanism of lithium metal batteries is provided along with corresponding advantages and existing challenges detailly described.The main catalysts employed to accelerate cathode reaction with emphasis on their catalytic mechanism are summarized as well.Finally,the rational design and innovative direction toward efficient catalysts are suggested for future application in metal-sulfur/gas battery and beyond.This review is expected to drive and benefit future research on rational catalyst design with multi-parameter synergistic impacts on the activity and stability of next-generation metal battery,thus opening new avenue for sustainable solution to climate change,energy and environmental issues,and the potential industrial economy.