Faults Analysis and Diagnosis of DRJ-460 Dish Centrifugal Separator′s Helical Gear

The main faults of dish centrifugal separator's helical gear are described inthis paper. In order to diagnose the DRJ-460 dish centrifugal separator correctly, the vibration istested with a helical gear under both normal and abnormal conditions. After comparing severalgeneral methods of the gear's fault feature extraction, a new convenient and effective method ispresented on the basis of analyzing the vibration spectrum under different rotary velocities.

Optimization of Drying Process for Plasma Protein from Tibetan Sheep

Fresh blood of Tibetan sheep was subjected to protein separation and spray drying, and the effects of drying process on water content, yield and nitrogen soluble index of plasma powder from blood of Tibetan sheep were investigated. The results showed that the optimum separation parameters were a centrifugal speed at 6 000 r/min, centrifugal time of 20 min, a mass fraction of dry matter of 20%, an inlet air temperature at 180 ℃ and a feed rate at 400 ml/h, under which the plasma protein was a pale yellow powdery solid, indicating a good separation effect.

Removal of primary iron rich phase from aluminum-silicon melt by centrifugal separation

Recycling is a major consideration in continued aluminum use due to the enormous demand for high quality products. Some impurity elements gradually accumulate through the repetitive reuse of aluminum alloy scrap. Of them, the iron content should be suppressed under the allowed limit. In the present research, a novel separation method was introduced to remove primary iron-rich intermetallic compounds by centrifugation during solidification of AI-Si-Fe alloys. This method does not use the density difference between two phases as in other centrifugal methods, but uses the order of solidification in AI-Si-Fe alloys, because iron promotes the formation of intermetallic compounds with other alloying elements as a primary phase. Two AI-Si-Fe alloys which have different iron contents were chosen as the starting materials. The iron-rich phase could be efficiently removed by centrifuging under a centrifugal force of 40 g. Coarse intermetallic compounds were found in the sample inside the crucible, while rather fine intermetallic compounds were found in the sample outside the crucible. Primary intermetallic compounds were linked to each other via aluminum-rich matrix, and formed like a network. The highest iron removal fraction is 67% and the lowest one is 7% for AI-12Si-1.7Fe alloy. And they are 82% and 18% for AI-12Si-3.4Fe alloy, respectively.

Metals Recovery from Fine Printed Circuit Boards Using Falcon SB Concentrator

Physical methods show great potential and advantages on comprehensive reutilization of waste printed circuit boards (PCBs) because of lower investment and operation cost, higher efficiency and environment friendliness. However, metals contained in fine fraction of PCBs cannot be recovered effectively by conventional equipments such as high tension electrostatic separator or shaking table. In the paper, this conundrum was resolved successfully with the enhanced Falcon SB concentrator. The separation mechanism of Falcon SB concentrator was analyzed and main factors affecting separation efficiency such as magnitude of rotation frequency of bowl, water counter pressure and slurry concentration of feed were studied and interaction of factors above also were investigated using Design-Expert software. Experiment results show that complete liberation degree and great difference of density between metals and nonmetals are suitable to recover metals from -74 μm PCBs using enhanced Falcon SB concentrator and 80.77 % integration efficiency can be achieved when slurry concentration of feed is 40 g/L with the water counter pressure of 0.01 MPa and rotation frequency of 50 Hz.

A Parametric Study for High-Efficiency Gas-Liquid Separator Design

A gas liquid centrifugal separator is widely used in industry on account of its simple geometry and little maintenance. These separators have considerable advantages over filters, scrubbers or precipitators in term of compact design, lower pressure drop and higher capacity. A gas liquid centrifugal separator is a device that utilizes centrifugal forces and low pressure caused by rotational motion to separate liquid from gas by density differences. Efficient and reliable separation is required for the optimum operation. These separators are often operated at less than peak efficiency due to the entrainment of separated liquid through an outlet pipe which is closely associated with the very complicated flow phenomena involved. Design parameters such as length of the separation space, vane exit angle, inlet to outlet diameter ratio, models for separation efficiency and pressure drop as a function of physical dimensions are not available in literature. This leaves the designer with very little to go on except known designs and experimentation. The aim of present study is to perform a parametric study to get higher efficiency for gas-liquid separator. A parametric study has been carded out with the help of CFD tools to analyze a separation performance of a centrifugal separator by varying the length of separator space. The best design parameters are analyzed based upon obtained results, tangential velocities, vortices, total pressure losses. From the present study several attempts are made to improve the performance of conventional centrifugal separators.