Comparative Study on Galvanic-Coupled Intrabody Channel Characteristic Measurement Methods

The galvanic-coupled intrabody communication(GCIBC)uses the human body as the channel for data transmission.The signal flow through different paths within different measure-ment schemes,resulting in distinct deviations in the experimental results.This method completely uses human body channel to transmit low-power signals,and has good anti-interference perform-ance.However,for a long time,the channel research of GCIBC has not determined a set of recog-nized and accurate measurement methods and standards.However,few researcher analyze the dif-ferences and principles between different measurement methods.This paper aims at three com-monly used measurement methods.Abstract the equivalent schematic diagrams of three measure-ment schemes:direct measurement,using high-precision differential probe and using balun.The sig-nal return paths generated by three measurement methods are analyzed,the impedance matching and energy transmission efficiency are compared.According to the analysis,the empirical expres-sions in different cases are listed.The mechanism between the channel measurement results gener-ated by the set experimental configuration and the comparison experiment is clarified.The compar-ison experiment with complete floating measurement is carried out as a reference to verify the pro-posed opinion.The measurement error caused by different experimental configurations is verified.This study can provide a reference opinions for the experimental error analysis of GCIBC research in the future,and provide suggestions for the selection of experimental configuration.

Power Flow Model for Medium-voltage Distribution Systems Considering Measurement and Structure Characteristics

Medium-voltage distribution systems(MVDSs)mainly consist of a feeder head,lines,distribution transformers,and the equivalent load or power supply interfaced with the distribution transformers.The information of such load or power supply can be measured via the three-wattmeter method(THM)and the two-wattmeter method(TWM).The measurements can be used to perform the control of the power supply and simulate the characteristics of the load,so the models of the load and the power supply need to consider the measurement characteristics.Existing research works on three-phase power flow(PF)just consider the measurement characteristics of THM.Hence,the PF equation of the bus measured via TWM is firstly built.Based on conventional measurements,an accurate and general model of the grounded and ungrounded slack bus is proposed.Furthermore,the influence arising from the connection type and angle shift of distribution transformers on the admittance matrix is considered,and thus a general three-phase transformer model is summarized,which is applicable for all the transformers mentioned herein.Finally,Newton's method is adopted to solve the PF calculation,and the performance of the proposed PF model is demonstrated through designed tests.

A Comparative Study of the Electrodes Gels’Electrical Properties in the Measurement Issues of Intrabody Communication

Intrabody communication(IBC)technology is becoming progressively more standard-ized due to its low power consumption and high security features incorporated into the third phys-ical layer of the IEEE 802.15.6 standard.Even then,there are still many challenges in normalizing the measurement issues of IBC.A major concern that should not be overlooked is the electrodes in the IBC,especially the popular use of gel electrodes.In the channel measurements,gel electrodes are commonly employed to improve the signal-to-noise ratio and prevent electrodes from falling off.In this paper,a comparative study of the electrical properties of gel was investigated during the measurement of human channel characteristics and to clarify the differences of them.Firstly,the basis of electrostatic field pole plate measurements and electromagnetic theory were introduced to interpretate how the relative permittivity and conductivity of different gels will influence the meas-urement results.Then the in vivo experiments with different gel or dry electrodes were performed to compare the differences induced by the gel.The results indicate that the influence of the gel on the human channel measurement is mainly concentrated below 400 kHz(the attenuation is re-duced by 16.7 dB on average),and the stability of the permittivity and conductivity of the gel has a direct impact on the stability of its measurement of the human channel.This result may provide a meaningful reference for the standardization of electrode usage in IBC.

Detonation Propagation Characteristics of Superposition Explosive Materials

In order to investigate detonation propagation characteristics of different charge patterns,the detonation velocities of superposition strip shaped charges made up of a detonating cord and explosives were measured by a detonation velocity measuring instrument under conditions of different ignition.The experimental results and theoretical analysis show that the maximum detonation propagation velocity depends on the explosive materials with the maximum velocity among all the explosive materials.Using detonating cord in a superposition charge can shorten detonation propagation time and improve the efficiency of explosive energy.The measurement method of detonation propagation velocity and experimental results are presented and investigated.

Extraction algorithm for longitudinal and transverse mechanical information of AFM

The atomic force microscope(AFM)can measure nanoscale morphology and mechanical properties and has a wide range of applications.The traditional method for measuring the mechanical properties of a sample does so for the longitudinal and transverse properties separately,ignoring the coupling between them.In this paper,a data processing and multidimensional mechanical information extraction algorithm for the composite mode of peak force tapping and torsional resonance is proposed.On the basis of a tip–sample interaction model for the AFM,longitudinal peak force data are used to decouple amplitude and phase data of transverse torsional resonance,accurately identify the tip–sample longitudinal contact force in each peak force cycle,and synchronously obtain the corresponding characteristic images of the transverse amplitude and phase.Experimental results show that the measured longitudinal mechanical characteristics are consistent with the transverse amplitude and phase characteristics,which verifies the effectiveness of the method.Thus,a new method is provided for the measurement of multidimensional mechanical characteristics using the AFM.

New dark current component of InGaAs/InP HPDs confirmed by DLTS

The dark current of In_(0.47) Ga_(0.53) As/InP heterojunction photodiodes (HPDs) was analysed. We found that there exists a new dark current component──deep level-assisted tunnelling current.DLTS was used to measure the In_(0.47)Ga_(0.53)As/InP HPDs. An electronic trap which has a thermal activation energy of O.44 eV, level concentration of 3.10×10￣(13)cm￣(-3) and electronic capture cross section of 1.72×10￣(12)cm￣2 has been found.It's existence results in the new tunnelling current.

Experiments and Simulation of Thermal Behaviors of the Dual-drive Servo Feed System

The machine tool equipped with the dual-drive servo feed system could realize high feed speed as well as sharp precision. Currently, there is no report about the thermal behaviors of the dual-drive machine, and the current research of the thermal characteristics of machines mainly focuses on steady simulation. To explore the influence of thermal characterizations on the precision of a jib boring machine assembled dual-drive feed system, the thermal equilibrium tests and the research on thermal-mechanical transient behaviors are carried out. A laser interferometer, infrared thermography and a temperature-displacement acquisition system are applied to measure the temperature distribution and thermal deformation at different feed speeds. Subsequently, the finite element method （FEM） is used to analyze the transient thermal behaviors of the boring machine. The complex boundary conditions, such as heat sources and convective heat transfer coefficient, are calculated. Finally, transient variances in temperatures and deformations are compared with the measured values, and the errors between the measurement and the simulation of the temperature and the thermal error are 2 ~C and 2.5 pm, respectively. The researching results demonstrate that the FEM model can predict the thermal error and temperature distribution very well under specified operating condition. Moreover, the uneven temperature gradient is due to the asynchronous dual-drive structure that results in thermal deformation. Additionally, the positioning accuracy decreases as the measured point became further away from the motor, and the thermal error and equilibrium period both increase with feed speeds. The research proposes a systematical method to measure and simulate the boring machine transient thermal behaviors.

Characteristics Measurement of AFLM-Grating Cavity WDM Fiber Laser

In this paper, we study an FLM-grating cavity WDM fiber laser with dynamic polarization compensation technique for maintaining the output polarization states. We observe the characteristics and obtain the optimal experimental results.

Polarization Projection for 3D Geometry-Based Stochastic Channel Model

Comprehensive radiation characteristics of polarized antenna are crucial in creating practical channel coefficients for next generation wireless communication system designs.Being currently supported within3 D geometry-based stochastic channel models(GSCM),field patterns are technically obtained by chamber measurement(or by its best fitting).However,in some channel related performance analysis scenarios,design insight can be crystallized better by starting the derivations with theoretical co-polarization and cross-polarization components.Specifically,these two components are mathematically linked with field patterns through the proposed polarization projection algorithm.In this manuscript,we focus on revealing the transformation criterion of polarization states between the antenna plane and the propagation plane.In practice,it makes retrieving the field patterns by electromagnetic computation possible.Meanwhile,the impact imposed by distinct antenna orientations is geometrically illustrated and consequently incorporated into the proposed algorithm.This will further facilitate flexible performance evaluation of related radio transmission technologies.Our conclusions are verified by the closed-form expression of the dipole field pattern(via an analytical approach) and by chamber measurement results.Moreover,we find that its 2D degenerative case is aligned with the definitions in 3^(rd) generation partnership project(3GPP)technical report 25.996.The most obvious benefit of the proposed algorithm is to significantly reduce the cost on generating channel coefficients in GSCM simulation.

Measured Impedance and Threshold Value of Electrode Line Impedance Supervision Based Protection in HVDC Transmission System

At present,electrode line impedance supervision(ELIS)based protection is widely used to detect faults on grounding electrode lines,which are indispensable elements of high-voltage direct current(HVDC)systems.The existing theoretical analysis of measured impedance is based on lumped line model and the threshold value is generally set according to engineering experience,which have caused the dead zone problem and even accidents.Therefore,a study on measured impedance of ELIS-based protection and its threshold value selection method is carried out to solve this problem.In this study,the expressions of measured impedance under normal operation and fault conditions are deduced based on rigorous and accurate line model.Based on the expressions,the characteristics of the measured impedance are calculated and analyzed.With the characteristics of the measured impedance,the applicability of the protection with the traditional threshold value is further discussed and the distribution of the dead zone can be located.Then,the method to calculate the threshold value of ELIS-based protection is proposed.With a proper threshold value selected by the proposed method,the dead zone of ELIS-based protection is effectively eliminated,and the protection can identify all types of faults even with large transition resistances.Case studies on PSCAD/EMTDC have been conducted to verify the conclusion.

Jump-diffusions with state-dependent switching:existence and uniqueness,Feller property,linearization,and uniform ergodicity

This work focuses on a class of jump-diffusions with state-dependent switching. First, compared with the existing results in the literature, in our model, the characteristic measure is allowed to be a-finite. The existence and uniqueness of the underlying process are obtained by representing the switching component as a stochastic integral with respect to a Poisson random measure and by using a successive approximation method. Then, the Feller property is proved by means of introducing auxiliary processes and by making use of Radon-Nikodym derivatives. Furthermore, the irreducibility and all compact sets being petite are demonstrated. Based on these results, the uniform ergodicity is established under a general Lyapunov condition. Finally, easily verifiable conditions for uniform ergodicity are established when the jump-diffusions are linearizable with respect to the variable x （the state variable corresponding to the jump-diffusion component） in a neighborhood of the infinity, and some examples are presented to illustrate the results.

Optimal Transportation for Generalized Lagrangian

This paper deals with the optimal transportation for generalized Lagrangian L = L（x, u, t）, and considers the following cost function： c（x, y） = inf x（0）=x x（1）=y u∈U∫0^1 L（x（s）, u（x（s）, s）, s）ds, where U is a control set, and x satisfies the ordinary equation x（s） = f（x（s）, u（x（s）, s））.It is proved that under the condition that the initial measure μ0 is absolutely continuous w.r.t. the Lebesgue measure, the Monge problem has a solution, and the optimal transport map just walks along the characteristic curves of the corresponding Hamilton-Jacobi equation：Vt（t, x） ＋ sup u∈U = 0,V（0, x） = Φ0（x）.