Chemical looping oxidative dehydrogenation (CL-ODH) is an economically promising method for convertingethane into higher value-added ethylene utilizing lattice oxygen in redox catalysts, also known as oxygen carriers....Chemical looping oxidative dehydrogenation (CL-ODH) is an economically promising method for convertingethane into higher value-added ethylene utilizing lattice oxygen in redox catalysts, also known as oxygen carriers. Inthis study, perovskite-type oxide SrCoO_(3-δ) and B-site Mn ion-doped oxygen carriers (SrCo_(1-x)MnxO_(3-δ), x=0.1, 0.2, 0.3)were prepared and tested for the CL-ODH of ethane. The oxygen-deficient perovskite SrCoO_(3-δ) exhibited high ethyleneselectivity of up to 96.7% due to its unique oxygen vacancies and lattice oxygen migration rates. However, its low ethyleneyield limits its application in the CL-ODH of ethane. Mn doping promoted the reducibility of SrCoO_(3-δ) oxygen carriers,thereby improving ethane conversion and ethylene yield, as demonstrated by characterization and evaluation experiments.X-ray diffraction results confirmed the doping of Mn into the lattice of SrCoO_(3-δ), while X-ray photoelectron spectroscopy(XPS) indicated an increase in lattice oxygen ratio upon incorporation of Mn into the SrCoO_(3-δ) lattice. Additionally, H2temperature-programmed reduction (H2-TPR) tests revealed more peaks at lower temperature reduction zones and a declinein peak positions at higher temperatures. Among the four tested oxygen carriers, SrCo0.8Mn0.2O_(3-δ) exhibited satisfactoryperformance with an ethylene yield of 50% at 710 °C and good stability over 20 redox cycles. The synergistic effect of Mnplays a key role in increasing ethylene yields of SrCoO_(3-δ) oxygen carriers. Accordingly, SrCo0.8Mn0.2O_(3-δ) shows promisingpotential for the efficient production of ethylene from ethane via CL-ODH.展开更多
Background Clostridium butyricum(CB)is a probiotic that can regulate intestinal microbial composition and improve meat quality.Rumen protected fat(RPF)has been shown to increase the dietary energy density and provide ...Background Clostridium butyricum(CB)is a probiotic that can regulate intestinal microbial composition and improve meat quality.Rumen protected fat(RPF)has been shown to increase the dietary energy density and provide essential fatty acids.However,it is still unknown whether dietary supplementation with CB and RPF exerts beneficial effects on growth performance and nutritional value of goat meat.This study aimed to investigate the effects of dietary CB and RPF supplementation on growth performance,meat quality,oxidative stability,and meat nutritional value of finishing goats.Thirty-two goats(initial body weight,20.5±0.82 kg)were used in a completely randomized block design with a 2 RPF supplementation(0 vs.30 g/d)×2 CB supplementation(0 vs.1.0 g/d)factorial treatment arrangement.The experiment included a 14-d adaptation and 70-d data and sample collection period.The goats were fed a diet consisted of 400 g/kg peanut seedling and 600 g/kg corn-based concentrate(dry matter basis).Result Interaction between CB and RPF was rarely observed on the variables measured,except that shear force was reduced(P<0.05)by adding CB or RPF alone or their combination;the increased intramuscular fat(IMF)content with adding RPF was more pronounced(P<0.05)with CB than without CB addition.The pH24h(P=0.009),a*values(P=0.007),total antioxidant capacity(P=0.050),glutathione peroxidase activities(P=0.006),concentrations of 18:3(P<0.001),20:5(P=0.003)and total polyunsaturated fatty acids(P=0.048)were increased,whereas the L*values(P<0.001),shear force(P=0.050)and malondialdehyde content(P=0.044)were decreased by adding CB.Furthermore,CB supplementation increased essential amino acid(P=0.027),flavor amino acid(P=0.010)and total amino acid contents(P=0.024)as well as upregulated the expression of lipoprotein lipase(P=0.034)and peroxisome proliferator-activated receptorγ(PPARγ)(P=0.012),and downregulated the expression of stearoyl-CoA desaturase(SCD)(P=0.034).The RPF supplementation increased dry matter intake(P=0.005),averaged daily gain(trend,P=0.058),hot carcass weight(P=0.046),backfat thickness(P=0.006),concentrations of 16:0(P<0.001)and c9-18:1(P=0.002),and decreased the shear force(P<0.001),isoleucine(P=0.049)and lysine content(P=0.003)of meat.In addition,the expressions of acetyl-CoA carboxylase(P=0.003),fatty acid synthase(P=0.038),SCD(P<0.001)and PPARγ(P=0.022)were upregulated due to RPF supplementation,resulting in higher(P<0.001)content of IMF.Conclusions CB and RPF could be fed to goats for improving the growth performance,carcass traits and meat quality,and promote fat deposition by upregulating the expression of lipogenic genes of Longissimus thoracis muscle.展开更多
Ethane chemical looping oxidative dehydrogenation(CL-ODH)to ethylene is a new technology for converting ethane to ethylene.In the current study MeO/LaCoO_(3)(MeO=Fe_(2)O_(3),NiO or Co_(2)O_(3))composite metal oxides w...Ethane chemical looping oxidative dehydrogenation(CL-ODH)to ethylene is a new technology for converting ethane to ethylene.In the current study MeO/LaCoO_(3)(MeO=Fe_(2)O_(3),NiO or Co_(2)O_(3))composite metal oxides were prepared via citrate gel and impregnation methods,and used as oxygen carriers for CL-ODH.X-ray diffraction results indicated that all oxygen carriers had a perovskite structure even after eight redox cycles.Under a reaction temperature of 650°C,a reaction pressure of 0.1 MPa,and a weight hourly space velocity(WHSV)of 7500 mL/(g·h),ethane conversion over Co_(2)O_(3)/LaCoO_(3) reached 100%and ethylene selectivity reached 60%,both of which were better than corresponding values attained over Fe_(2)O_(3)/LaCoO_(3) and NiO/LaCoO_(3).Ethylene selectivity remained stable for 80 cycles over Co_(2)O_(3)/LaCoO_(3),then decreased gradually after 80 cycles.X-ray photoelectron spectroscopy results and evaluation results indicated that lattice oxygen and O_(2)2-had a direct relationship with ethane conversion and ethylene selectivity.Co_(2)O_(3)/LaCoO_(3) exhibited a strong capacity to release and absorb oxygen,mainly due to interaction between Co_(2)O_(3) and LaCoO_(3).展开更多
Ethane chemical looping oxidative dehydrogenation(CL-ODH)to ethylene is a new technology for ethylene preparation.Fe_(2)O_(3)/MgO oxygen carrier was prepared using the co-precipitation method.The influence of added Ni...Ethane chemical looping oxidative dehydrogenation(CL-ODH)to ethylene is a new technology for ethylene preparation.Fe_(2)O_(3)/MgO oxygen carrier was prepared using the co-precipitation method.The influence of added NiO and its different loadings on Fe_(2)O_(3)/MgO were investigated.Then,a series of oxygen carriers were applied in the CL-ODH of the ethane cycle system.Brunauer-Emmett-Teller(BET),X-ray diffractometry(XRD),X-ray photoelection spectroscopy(XPS),and H2-temperature programmed reduction(TPR)were used to characterize the physicochemical properties of these oxygen carriers.It was confirmed that an interaction between NiO and Fe_(2)O_(3) occurred based on the XPS and H2-TPR results.Based on the CL-ODH activity performance tests conducted in a fixed-bed reactor,it was revealed that ethylene selectivity was significantly improved after NiO addition.Fe_(2)O_(3)-10%NiO/MgO showed the best activity performance with 93%ethane conversion and 50%ethylene selectivity at a reaction temperature of 650℃,atmospheric pressure,and space velocity of 7500 mL/(g·h).展开更多
The oxygen distribution and evolution within the oxygen carrier exert significant influence on chemical looping processes.This paper describes the influence of oxygen bulk diffusion within FeVO4 oxygen carrier pellets...The oxygen distribution and evolution within the oxygen carrier exert significant influence on chemical looping processes.This paper describes the influence of oxygen bulk diffusion within FeVO4 oxygen carrier pellets on the chemical looping oxidative propane dehydrogenation(CL-ODH).During CL-ODH,the oxygen concentration at the pellet surface initially decreased and then maintained stable before the final decrease.At the stage with the stable surface oxygen concentration,the reaction showed a stable C3H6 formation rate and high C3H6 selectivity.Therefore,based on Fick’s second law,the oxygen distribution and evolution in the oxygen carrier at this stage were further analyzed.It was found that main reactions of selective oxidation and over-oxidation were controlled by the oxygen bulk diffusion.C3H8 conversion rate kept decreasing during this stage due to the decrease of the oxygen flux caused by the decline of oxygen gradient within the oxygen carrier,while C3H6 selectivity increased due to the decrease of overoxidation.In addition,reaction rates could increase with the propane partial pressure due to the increase of the oxygen gradient within the oxygen carrier until the bulk transfer reached its limit at higher propane partial pressure.This study provides fundamental insights for the diffusion-controlled chemical looping reactions.展开更多
The kinetics of aniline degradation by persulfate processes with iron(Ⅱ) activation at ambient temperature was investigated in this study.With iron(Ⅱ) as initiator,the oxidation reactions were found to follow a ...The kinetics of aniline degradation by persulfate processes with iron(Ⅱ) activation at ambient temperature was investigated in this study.With iron(Ⅱ) as initiator,the oxidation reactions were found to follow a biphasic rate phenomenon:a rapid transformation followed by a slow but sustained oxidation process.In the first 30 s,the reaction mainly relies on the persulfate-Fe^(2+) reaction in which aniline is oxidized rapidly.After 30 s,the aniline was still oxidized but the rate of reaction tended to be slower and the rates were clearly linear-proportional.After the initial fast oxidation,the reactions appeared to follow a pseudo-first-order model.展开更多
The removal of the natural organic matter present in coffee processing wastewater through chemical coagulation-flocculation and advanced oxidation processes (AOP) had been studied. The effectiveness of the removal o...The removal of the natural organic matter present in coffee processing wastewater through chemical coagulation-flocculation and advanced oxidation processes (AOP) had been studied. The effectiveness of the removal of natural organic matter using commercial flocculants and UV/H202, UV/O3 and UV/H2O2/O3 processes was determined under acidic conditions. For each of these processes, different operational conditions were explored to optimize the treatment efficiency of the coffee wastewater. Coffee wastewater is characterized by a high chemical oxygen demand (COD) and low total suspended solids. The outcomes of coffee wastewater treatment using coagulation-flocculation and photodegradation processes were assessed in terms of reduction of COD, color, and turbidity. It was found that a reduction in COD of 67% could be realized when the coffee wastewater was treated by chemical coagulation-flocculation with lime and coagulant T-1. When coffee wastewater was treated by coagulation-flocculation in combination with UV/H2O2, a COD reduction of 86% was achieved, although only after prolonged UV irradiation. Of the three advanced oxidation processes considered, UV/H2O2, UV/O3 and UV/H2O2/O3, we found that the treatment with UV/H2O2/O3 was the most effective, with an efficiency of color, turbidity and further COD removal of 87%, when applied to the flocculated coffee wastewater.展开更多
Double-perovskite type oxide LaSrFeCoO(LSFCO) was used as oxygen carrier for chemical looping steam methane reforming(CL-SMR) due to its unique structure and reactivity. Two different oxidation routes,steam-oxidat...Double-perovskite type oxide LaSrFeCoO(LSFCO) was used as oxygen carrier for chemical looping steam methane reforming(CL-SMR) due to its unique structure and reactivity. Two different oxidation routes,steam-oxidation and steam-air-stepwise-oxidation, were applied to investigate the recovery behaviors of the lattice oxygen in the oxygen carrier. The characterizations of the oxide were determined by X-ray diffraction(XRD), X-ray photoelectron spectroscopy(XPS), hydrogen temperature-programmed reduction(H-TPR) and scanning electron microscopy(SEM). The fresh sample LSFCO exhibits a monocrystalline perovskite structure with cubic symmetry and high crystallinity, except for a little impurity phase due to the antisite defect of Fe/Co disorder. The deconvolution distribution of XPS patterns indicated that Co,and Fe are predominantly in an oxidized state(Feand Fe) and(Coand Co), while O 1s exists at three species of lattice oxygen, chemisorbed oxygen and physical adsorbed oxygen. The double perovskite structure and chemical composition recover to the original state after the steam and air oxidation, while the Co ion cannot incorporate into the double perovskite structure and thus form the CoO just via individual steam oxidation. In comparison to the two different oxidation routes, the sample obtained by steam-oxidation exhibits even higher CHconversion, CO and Hselectivity and stronger hydrogen generation capacity.展开更多
Supercritical water oxidation (SCWO) has been drawing much attention due to effectively destroy a large variety of high-risk wastes resulting from munitions demilitarization and complex industrial chemical. An impor...Supercritical water oxidation (SCWO) has been drawing much attention due to effectively destroy a large variety of high-risk wastes resulting from munitions demilitarization and complex industrial chemical. An important design consideration in the development of supercritical water oxidation is the information of decomposition rate. In this paper, the decomposition rate of dimethyl methylphosphonate(DMMP), which is similar to the nerve agent VX and GB(Sarin) in its structure, was investigated under SCWO conditions. The experiments were performed in an isothermal tubular reactor with a H2O2 as an oxidant. The reaction temperatures were ranged from 398 to 633℃ at a fixed pressure of 24 MPa. The conversion of DMMP was monitored by analyzing total organic carbon (TOC) on the liquid effluent samples. It is found that the oxidative decomposition of DMMP proceeded rapidly and a high TOC decomposition up to 99.99% was obtained within 11 s at 555℃. On the basis of data derived from experiments, a global kinetic equation for the decomposition of DMMP was developed. The model predictions agreed well with the experimental data.展开更多
Wastewater after chemical flooding is difficult to be treated by biological methods due to the residual chemicals in the wastewater. Fenton oxidation, which has been widely applied to detoxifying hazardous organic com...Wastewater after chemical flooding is difficult to be treated by biological methods due to the residual chemicals in the wastewater. Fenton oxidation, which has been widely applied to detoxifying hazardous organic compounds and improving the biodegradability of these compounds, can solve this problem. So, in this paper, Fenton oxidation was used to enhance the biodegradability of the wastewater after chemical flooding. The op- timum operating conditions for the Fenton oxidation process were 2.5 g/L Fe2 + , 600 mg/L H202 and 30 rain of treatment time. The wastewater pre- treated by Fenton oxidation was treated by aerobic activated sludge. It was found that a small amount of H202 can significantly increase both the biodegradation rate and extent of the wastewater. The effluent CODc, and HPAM contents were 260 and 94 mg/L respectively after the aerobic bio- logical process with the biodegradation time of 24 h. After Fenton oxidation combining with biodegradation, the total CODc, removal efficiency was up to 90%, and polymer and oil degrading efficiencies were 95% and 92% respectively.展开更多
Anode material for lithium ion battery is prepared by chemical oxidation of natural graphite. After oxidation, the properties of natural graphite are modified, such as surface structure, the content of graphite phases...Anode material for lithium ion battery is prepared by chemical oxidation of natural graphite. After oxidation, the properties of natural graphite are modified, such as surface structure, the content of graphite phases, the number of micropores and its stability. thus the modified natural graphite can be used as anode material for commercial lithium ion battery. The reversible capacity is increased from 100 mAh/g to above 300 mAh/g, and its cycling properly is also satisfactory.展开更多
A novel sensor for ocean electric field testing has been fabricated by polyacrylonitrile-based on carbon fibers with electro-chemical oxidation.The surface profile characteristics of the carbon fibers were characteriz...A novel sensor for ocean electric field testing has been fabricated by polyacrylonitrile-based on carbon fibers with electro-chemical oxidation.The surface profile characteristics of the carbon fibers were characterized by scanning electron microscope,Fourier transform infrared spectra and contact angle.Cyclic voltammetry and Tafel curves have been used to study its electro-chemical performances.Two identical electrodes in sea water as the electric field sensor will swiftly respond to applied electric field which causes positive and negative ions to move in opposite direction,resulting in a electric potential difference(ΔE).Test result indicates that the offset potential is typically below 1 m V with a drift of 60-170μVd^-1.Typical self noise level is 1.07 nV√Hz^(1/2)@1 Hz.The electric field response indicates that the modified electrode pair shows better response to AC sine signal of amplitude and frequency(5 mV and 1 mHz)respectively than its blank.The electric field response model of the modified electrodes is creatively presented according to its electric double layer capacitance and Faraday pseudo-capacitance.Many advantages of the carbon fiber electric field electrode will make it have potential application prospect.展开更多
To improve the oxidation-resistance properties,SiC and TaC species were introduced in C/C composites by chemical vapor infiltration(CVI) methods. The oxidation-resistance properties of C-SiC-TaC-C composites were stud...To improve the oxidation-resistance properties,SiC and TaC species were introduced in C/C composites by chemical vapor infiltration(CVI) methods. The oxidation-resistance properties of C-SiC-TaC-C composites were studied by X-Ray diffractometry(XRD),JEOL-6360LV scanning electronic microscopy(SEM) and AdventurerTM electronic balance with precision of 0.1 mg. The results show that,1) the oxidation rate of the composites increases continuously with time at all experimental temperatures;2) The oxidation rate increases with temperature within 700-1 100 ℃,slowly in 700-800 ℃,acutely in 800-1 100 ℃;it reaches a maximum value at 1 100 ℃,then decreases within 1 100-1 400 ℃;3) The relationship curve of oxidation rate with temperature can be divided into three regions. The oxidation rate is controlled by reactivity in region Ⅰ,the mixed effects of reactivity and gas diffusion in region Ⅱ,gas phase diffusion in region Ⅲ;4) The composites exhibit a higher oxidation onset temperature in low temperature region and a lower oxidation rate at high temperature due to the oxidation of TaC to(Ta,O) and the formation of the dense SiO2-Ta2O5 oxide layer respectively. With the addition of SiC/TaC species,the oxidation-resistant properties of C/C composites can be improved effectively.展开更多
XPS and chemical trapping experments with H2, NH3, and CH3I as trapping agents were carried out for studying the adsorption of propylene over MoO3 or r-Bi2MoO6. The results show that the fragmentation of carbon chain ...XPS and chemical trapping experments with H2, NH3, and CH3I as trapping agents were carried out for studying the adsorption of propylene over MoO3 or r-Bi2MoO6. The results show that the fragmentation of carbon chain takes place during the adsorption of propylene through breaking C -C double bond and C-C bond on Mo2+ and the adjacent lattice oxygen, leading to formation of the oxygen- or nitrogen-containing by-products of C1 and C2 species. Diffuse-Reflection Fourier Transform Infrared (DRFTIR) Spectroscopy was used to study the surface species formed during the chemisorption and reaction of propylene over y-Bi2MoO6 at a lower temperature. The results that C1, C2 adspecies were detected by DRFTIR at 175℃ are consistent with the results of XPS and chemical trapping experiments, whlle the results at 50℃ Grasselli et al.展开更多
The experimental degradation of a water soluble dye, potassium indigo tetrasulfonate salt, has been studied using stand-alone ozonation and photocatalytic oxidation process. Progress of the dye oxidation was followed ...The experimental degradation of a water soluble dye, potassium indigo tetrasulfonate salt, has been studied using stand-alone ozonation and photocatalytic oxidation process. Progress of the dye oxidation was followed by UV-VIS spectrophotometric measurements at controlled operating conditions. The organic content of reaction samples was measured to verify the process efficiency in dye mineralization. According to current results, almost complete color removal was obtained for ozonation within about 1 h reaction time. The reduction of the organic load was almost 80% from its original while initial sulphur content decreased to 32.5%. Dye conversion of 100% was obtained by means of a photocatalytic process using TiO2 as catalyst at 294 nm irradiated UV light. This complete color removal for the catalytic process was observed within 7 min of reaction time. The calculated initial rate of reaction of photocatalysis treatment was 8 times faster than that of ozonolysis. However, the remaining organic load of photocatalysis was almost 88% from its original while the final sulphur content was 27.3%. This contrasting behavior of the performance of the type of oxidation process stressed importance of physicochemical phenomena and intermediates molecules present during dye degradation. An insightful and mechanistic aspect of the dye oxidation was developed by performing quantumchemical calculations.展开更多
Nano-TiO2 photocatalytic oxidation was used to perform the advanced treatment of biologically treated chemical comprehensive wastewater. The effects of reaction time,nano-TiO2 dosage and initial p H of the wastewater ...Nano-TiO2 photocatalytic oxidation was used to perform the advanced treatment of biologically treated chemical comprehensive wastewater. The effects of reaction time,nano-TiO2 dosage and initial p H of the wastewater on the removal rate of COD were tested. The GC/MS and EEM techniques were used to qualitatively analyze organic compounds in the wastewater before and after treatment. The result showed that after the biologically treated chemical comprehensive wastewater was treated by nano-TiO2 photocatalytic oxidation under the conditions of reaction time 3 h,nano-TiO2 dosage 8 g/L,and pH 8. 0,the effluent COD was 61. 9 mg/L and its removal rate was 63. 8%. Additionally,the species of organic pollutants reduced from 12 to 6. Meanwhile,the content of humic-like and fulvic-like substances dropped dramatically.展开更多
Acidic black 10B dye wastewater was treated by chemical oxidation and adsorption of activated carbon fixed bed and all kinds of influential factors of removal CODcr were discussed. When the initial concentration of th...Acidic black 10B dye wastewater was treated by chemical oxidation and adsorption of activated carbon fixed bed and all kinds of influential factors of removal CODcr were discussed. When the initial concentration of the dye was 150 mg/L, CODer was 432 mg/L and chrome was 2800 times, the appropriate conditions determined by the experiment were as follows: r(NaC10)--4.84 g/L, 25 min, pH=6, height of activated carbon fixed bed was 10 cm. Under these conditions, the decolorizing rate can come up to about 100% and total removed rate of CODer reached at 89.6%. Comparison of UV-Vis adsorption spectrums before and after treatment showed that decomposition effects of chemical oxidation and adsorption of activated carbon fixed bed on acidic black 10B dye wastewater were satisfactory.展开更多
Male sterility induced by a chemical hybridization agent (CHA) is an important tool for utilizing crop heterosis. Leaves, especially the flag leaves, as CHA initial recipients play a decisive role in inducing male s...Male sterility induced by a chemical hybridization agent (CHA) is an important tool for utilizing crop heterosis. Leaves, especially the flag leaves, as CHA initial recipients play a decisive role in inducing male sterility. To investigate effects of different treatment times of CHA-SQ-1 used, morphological, biochemical and physiological responses of wheat flag leaves were detected in thistudy. CHA induced programmed cell death (PCD) as shown in terminal deoxynucleotidyl transferase-mediated dUTP nick end-labelling (TUNEL) and DNA laddering analysis. In the early phase, CHA-SQ-1 trig- gered organelle changes arid PCD in wheat leaves accompanied by excess production of reactive oxygen species (O2- and H202) and down-regulation of the activities of superoxide dismutase (SOD), catalase (CAT) and guaiacol peroxidase (POD). Meanwhile, leaf cell DNAs showed ladder-like patterns on agarose gel, indicating that CHA-SQ-1 led to the activation of the responsible endonuclease. The oxidative stress assays showed that lipid peroxidation was strongly activated and photosynthesis was obviously inhibited in SQ-l-induced leaves. However, CHA contents in wheat leaves gradually reduced along with the time CHA-SQ-1 applied. Young flags returned to an oxidative/antioxidative balance and ultimately developed into mature green leaves. These results provide explanation of the relations between PCD and anther abortion and practical application of CHA for hybrid breeding.展开更多
The results of a system analysis of the efficiency of nitrous oxide(N_2O) as a propellant component for small space vehicles(SSV) were presented. A criterion for mass efficiency of the SSV propulsion system(PS) is det...The results of a system analysis of the efficiency of nitrous oxide(N_2O) as a propellant component for small space vehicles(SSV) were presented. A criterion for mass efficiency of the SSV propulsion system(PS) is determined. The current global state-of-the-art of SSV PSs is shown. The application field of nitrous oxide in SSV PSs is calculated and mass efficiency of N_2O application is quantitatively determined. An overview of physical and chemical as well as operational properties of nitrous oxide as a promising, non-toxic component of rocket propellant is provided. Main physical and chemical constants of gaseous and liquid nitrous oxide; chemical properties of N_2O, thermal stability of N_2O, catalytic decomposition of N_2O, a mechanism of decomposition of N_2O, catalysts for decomposition of N_2O, ballast additives to N_2O, application of nitrous oxide, nitrous oxide as a rocket propellant, production of nitrous oxide, toxicity of nitrous oxide, fire hazard of N_2O, requirements to equipment when handling N_2O; storage and transportation of N_2O are considered. It is demonstrated that nitrous oxide is a chemical compound meeting the requirements to rocket propellants, including those related to the environmental friendliness of propellants. With 75 references.展开更多
The chemical stripping method of titanium alloy oxide films was studied. An environment friendly solution hydrogen peroxide and sodium hydroxide without hydrofluoric acid or fluoride were used to strip the oxide films...The chemical stripping method of titanium alloy oxide films was studied. An environment friendly solution hydrogen peroxide and sodium hydroxide without hydrofluoric acid or fluoride were used to strip the oxide films. The morphologies of the surface and cross-section of the oxide films before and after the films stripping were characterized by using scanning electron microscopy (SEM). The microstructure and chemical compositions of the oxide films before and after the films stripping were investigated by using Raman spectroscopy (Raman) and X-ray photoelectron spectroscopy (XPS). It was shown that the thickness of the oxide film was in the range of 5-6 μm. The oxide films were stripped for 2 to 8 min in the solution. Moreover, the effect of the stripping time on the efficiency of the film stripping was investigated, and the optimum stripping time was between 6-8 min. When the stripping solution completely dissolved the whole film, the α/β microstructure of the titanium alloy Ti-10V-2Fe-3Al was partly revealed. The stripping mechanism was discussed in terms of the dissolution of film delamination. The hydrogen peroxide had a significant effect on the dissolution of the titanium alloy anodic oxide film. The feasibility of the dissolution reaction also was evaluated.展开更多
基金the SINOPEC Research and Development Project(No.JR22094).
文摘Chemical looping oxidative dehydrogenation (CL-ODH) is an economically promising method for convertingethane into higher value-added ethylene utilizing lattice oxygen in redox catalysts, also known as oxygen carriers. Inthis study, perovskite-type oxide SrCoO_(3-δ) and B-site Mn ion-doped oxygen carriers (SrCo_(1-x)MnxO_(3-δ), x=0.1, 0.2, 0.3)were prepared and tested for the CL-ODH of ethane. The oxygen-deficient perovskite SrCoO_(3-δ) exhibited high ethyleneselectivity of up to 96.7% due to its unique oxygen vacancies and lattice oxygen migration rates. However, its low ethyleneyield limits its application in the CL-ODH of ethane. Mn doping promoted the reducibility of SrCoO_(3-δ) oxygen carriers,thereby improving ethane conversion and ethylene yield, as demonstrated by characterization and evaluation experiments.X-ray diffraction results confirmed the doping of Mn into the lattice of SrCoO_(3-δ), while X-ray photoelectron spectroscopy(XPS) indicated an increase in lattice oxygen ratio upon incorporation of Mn into the SrCoO_(3-δ) lattice. Additionally, H2temperature-programmed reduction (H2-TPR) tests revealed more peaks at lower temperature reduction zones and a declinein peak positions at higher temperatures. Among the four tested oxygen carriers, SrCo0.8Mn0.2O_(3-δ) exhibited satisfactoryperformance with an ethylene yield of 50% at 710 °C and good stability over 20 redox cycles. The synergistic effect of Mnplays a key role in increasing ethylene yields of SrCoO_(3-δ) oxygen carriers. Accordingly, SrCo0.8Mn0.2O_(3-δ) shows promisingpotential for the efficient production of ethylene from ethane via CL-ODH.
基金supported by the National Key Research and Development Program of China(2022YFD1301105)the earmarked fund for CARS(CARS-36)+2 种基金the Natural Science Foundation of Heilongjiang Province(YQ2021C018)the Postdoctoral Foundation of Heilongjiang Province(LBH-Z21100)the Open Project Program of International Joint Research Laboratory in Universities of Jiangsu Province of China for Domestic Animal Germplasm Resources and Genetic Improvement(IJRLD-KF202204).
文摘Background Clostridium butyricum(CB)is a probiotic that can regulate intestinal microbial composition and improve meat quality.Rumen protected fat(RPF)has been shown to increase the dietary energy density and provide essential fatty acids.However,it is still unknown whether dietary supplementation with CB and RPF exerts beneficial effects on growth performance and nutritional value of goat meat.This study aimed to investigate the effects of dietary CB and RPF supplementation on growth performance,meat quality,oxidative stability,and meat nutritional value of finishing goats.Thirty-two goats(initial body weight,20.5±0.82 kg)were used in a completely randomized block design with a 2 RPF supplementation(0 vs.30 g/d)×2 CB supplementation(0 vs.1.0 g/d)factorial treatment arrangement.The experiment included a 14-d adaptation and 70-d data and sample collection period.The goats were fed a diet consisted of 400 g/kg peanut seedling and 600 g/kg corn-based concentrate(dry matter basis).Result Interaction between CB and RPF was rarely observed on the variables measured,except that shear force was reduced(P<0.05)by adding CB or RPF alone or their combination;the increased intramuscular fat(IMF)content with adding RPF was more pronounced(P<0.05)with CB than without CB addition.The pH24h(P=0.009),a*values(P=0.007),total antioxidant capacity(P=0.050),glutathione peroxidase activities(P=0.006),concentrations of 18:3(P<0.001),20:5(P=0.003)and total polyunsaturated fatty acids(P=0.048)were increased,whereas the L*values(P<0.001),shear force(P=0.050)and malondialdehyde content(P=0.044)were decreased by adding CB.Furthermore,CB supplementation increased essential amino acid(P=0.027),flavor amino acid(P=0.010)and total amino acid contents(P=0.024)as well as upregulated the expression of lipoprotein lipase(P=0.034)and peroxisome proliferator-activated receptorγ(PPARγ)(P=0.012),and downregulated the expression of stearoyl-CoA desaturase(SCD)(P=0.034).The RPF supplementation increased dry matter intake(P=0.005),averaged daily gain(trend,P=0.058),hot carcass weight(P=0.046),backfat thickness(P=0.006),concentrations of 16:0(P<0.001)and c9-18:1(P=0.002),and decreased the shear force(P<0.001),isoleucine(P=0.049)and lysine content(P=0.003)of meat.In addition,the expressions of acetyl-CoA carboxylase(P=0.003),fatty acid synthase(P=0.038),SCD(P<0.001)and PPARγ(P=0.022)were upregulated due to RPF supplementation,resulting in higher(P<0.001)content of IMF.Conclusions CB and RPF could be fed to goats for improving the growth performance,carcass traits and meat quality,and promote fat deposition by upregulating the expression of lipogenic genes of Longissimus thoracis muscle.
文摘Ethane chemical looping oxidative dehydrogenation(CL-ODH)to ethylene is a new technology for converting ethane to ethylene.In the current study MeO/LaCoO_(3)(MeO=Fe_(2)O_(3),NiO or Co_(2)O_(3))composite metal oxides were prepared via citrate gel and impregnation methods,and used as oxygen carriers for CL-ODH.X-ray diffraction results indicated that all oxygen carriers had a perovskite structure even after eight redox cycles.Under a reaction temperature of 650°C,a reaction pressure of 0.1 MPa,and a weight hourly space velocity(WHSV)of 7500 mL/(g·h),ethane conversion over Co_(2)O_(3)/LaCoO_(3) reached 100%and ethylene selectivity reached 60%,both of which were better than corresponding values attained over Fe_(2)O_(3)/LaCoO_(3) and NiO/LaCoO_(3).Ethylene selectivity remained stable for 80 cycles over Co_(2)O_(3)/LaCoO_(3),then decreased gradually after 80 cycles.X-ray photoelectron spectroscopy results and evaluation results indicated that lattice oxygen and O_(2)2-had a direct relationship with ethane conversion and ethylene selectivity.Co_(2)O_(3)/LaCoO_(3) exhibited a strong capacity to release and absorb oxygen,mainly due to interaction between Co_(2)O_(3) and LaCoO_(3).
文摘Ethane chemical looping oxidative dehydrogenation(CL-ODH)to ethylene is a new technology for ethylene preparation.Fe_(2)O_(3)/MgO oxygen carrier was prepared using the co-precipitation method.The influence of added NiO and its different loadings on Fe_(2)O_(3)/MgO were investigated.Then,a series of oxygen carriers were applied in the CL-ODH of the ethane cycle system.Brunauer-Emmett-Teller(BET),X-ray diffractometry(XRD),X-ray photoelection spectroscopy(XPS),and H2-temperature programmed reduction(TPR)were used to characterize the physicochemical properties of these oxygen carriers.It was confirmed that an interaction between NiO and Fe_(2)O_(3) occurred based on the XPS and H2-TPR results.Based on the CL-ODH activity performance tests conducted in a fixed-bed reactor,it was revealed that ethylene selectivity was significantly improved after NiO addition.Fe_(2)O_(3)-10%NiO/MgO showed the best activity performance with 93%ethane conversion and 50%ethylene selectivity at a reaction temperature of 650℃,atmospheric pressure,and space velocity of 7500 mL/(g·h).
基金the National Key Research and Development Program of China (2021YFA1501302)the National Natural Science Foundation of China (22122808, U20B6002)+1 种基金the Haihe Laboratory of Sustainable Chemical Transformations and the Program of Introducing Talents of Discipline to Universities (BP0618007) for financial supportsupported by the XPLORER PRIZE by Tencent Foundation
文摘The oxygen distribution and evolution within the oxygen carrier exert significant influence on chemical looping processes.This paper describes the influence of oxygen bulk diffusion within FeVO4 oxygen carrier pellets on the chemical looping oxidative propane dehydrogenation(CL-ODH).During CL-ODH,the oxygen concentration at the pellet surface initially decreased and then maintained stable before the final decrease.At the stage with the stable surface oxygen concentration,the reaction showed a stable C3H6 formation rate and high C3H6 selectivity.Therefore,based on Fick’s second law,the oxygen distribution and evolution in the oxygen carrier at this stage were further analyzed.It was found that main reactions of selective oxidation and over-oxidation were controlled by the oxygen bulk diffusion.C3H8 conversion rate kept decreasing during this stage due to the decrease of the oxygen flux caused by the decline of oxygen gradient within the oxygen carrier,while C3H6 selectivity increased due to the decrease of overoxidation.In addition,reaction rates could increase with the propane partial pressure due to the increase of the oxygen gradient within the oxygen carrier until the bulk transfer reached its limit at higher propane partial pressure.This study provides fundamental insights for the diffusion-controlled chemical looping reactions.
基金supported by a grant from E.I.du Pont de Nemours and Company to Rutgers University.Partial funding wasalso provided by the Natural Science Foundation of Guangdong Province(No.9351064101000001)Science and Technology Planning Project of Guangdong Province(No.2007A020100001-13)the Key Laboratory of Environmental Protection and Eco-Remediation of Guangdong Higher Education Institutions(China)
文摘The kinetics of aniline degradation by persulfate processes with iron(Ⅱ) activation at ambient temperature was investigated in this study.With iron(Ⅱ) as initiator,the oxidation reactions were found to follow a biphasic rate phenomenon:a rapid transformation followed by a slow but sustained oxidation process.In the first 30 s,the reaction mainly relies on the persulfate-Fe^(2+) reaction in which aniline is oxidized rapidly.After 30 s,the aniline was still oxidized but the rate of reaction tended to be slower and the rates were clearly linear-proportional.After the initial fast oxidation,the reactions appeared to follow a pseudo-first-order model.
文摘The removal of the natural organic matter present in coffee processing wastewater through chemical coagulation-flocculation and advanced oxidation processes (AOP) had been studied. The effectiveness of the removal of natural organic matter using commercial flocculants and UV/H202, UV/O3 and UV/H2O2/O3 processes was determined under acidic conditions. For each of these processes, different operational conditions were explored to optimize the treatment efficiency of the coffee wastewater. Coffee wastewater is characterized by a high chemical oxygen demand (COD) and low total suspended solids. The outcomes of coffee wastewater treatment using coagulation-flocculation and photodegradation processes were assessed in terms of reduction of COD, color, and turbidity. It was found that a reduction in COD of 67% could be realized when the coffee wastewater was treated by chemical coagulation-flocculation with lime and coagulant T-1. When coffee wastewater was treated by coagulation-flocculation in combination with UV/H2O2, a COD reduction of 86% was achieved, although only after prolonged UV irradiation. Of the three advanced oxidation processes considered, UV/H2O2, UV/O3 and UV/H2O2/O3, we found that the treatment with UV/H2O2/O3 was the most effective, with an efficiency of color, turbidity and further COD removal of 87%, when applied to the flocculated coffee wastewater.
基金The financial support of the National Natural Science Foundation of China(51406208,51406214)supported by the Science&Technology Research Project of Guangdong Province(2015A010106009)the support of Key Laboratory of Renewable Energy,Chinese Academy of Sciences(Y607j51001)
文摘Double-perovskite type oxide LaSrFeCoO(LSFCO) was used as oxygen carrier for chemical looping steam methane reforming(CL-SMR) due to its unique structure and reactivity. Two different oxidation routes,steam-oxidation and steam-air-stepwise-oxidation, were applied to investigate the recovery behaviors of the lattice oxygen in the oxygen carrier. The characterizations of the oxide were determined by X-ray diffraction(XRD), X-ray photoelectron spectroscopy(XPS), hydrogen temperature-programmed reduction(H-TPR) and scanning electron microscopy(SEM). The fresh sample LSFCO exhibits a monocrystalline perovskite structure with cubic symmetry and high crystallinity, except for a little impurity phase due to the antisite defect of Fe/Co disorder. The deconvolution distribution of XPS patterns indicated that Co,and Fe are predominantly in an oxidized state(Feand Fe) and(Coand Co), while O 1s exists at three species of lattice oxygen, chemisorbed oxygen and physical adsorbed oxygen. The double perovskite structure and chemical composition recover to the original state after the steam and air oxidation, while the Co ion cannot incorporate into the double perovskite structure and thus form the CoO just via individual steam oxidation. In comparison to the two different oxidation routes, the sample obtained by steam-oxidation exhibits even higher CHconversion, CO and Hselectivity and stronger hydrogen generation capacity.
文摘Supercritical water oxidation (SCWO) has been drawing much attention due to effectively destroy a large variety of high-risk wastes resulting from munitions demilitarization and complex industrial chemical. An important design consideration in the development of supercritical water oxidation is the information of decomposition rate. In this paper, the decomposition rate of dimethyl methylphosphonate(DMMP), which is similar to the nerve agent VX and GB(Sarin) in its structure, was investigated under SCWO conditions. The experiments were performed in an isothermal tubular reactor with a H2O2 as an oxidant. The reaction temperatures were ranged from 398 to 633℃ at a fixed pressure of 24 MPa. The conversion of DMMP was monitored by analyzing total organic carbon (TOC) on the liquid effluent samples. It is found that the oxidative decomposition of DMMP proceeded rapidly and a high TOC decomposition up to 99.99% was obtained within 11 s at 555℃. On the basis of data derived from experiments, a global kinetic equation for the decomposition of DMMP was developed. The model predictions agreed well with the experimental data.
基金supported by Zhejiang Provincial Natural Science Foundation of China under Grant No.LQ13D060001 and No.LY14D060003Science and Technology Plan Project of Zhoushan City under Grant No.2014C41004
文摘Wastewater after chemical flooding is difficult to be treated by biological methods due to the residual chemicals in the wastewater. Fenton oxidation, which has been widely applied to detoxifying hazardous organic compounds and improving the biodegradability of these compounds, can solve this problem. So, in this paper, Fenton oxidation was used to enhance the biodegradability of the wastewater after chemical flooding. The op- timum operating conditions for the Fenton oxidation process were 2.5 g/L Fe2 + , 600 mg/L H202 and 30 rain of treatment time. The wastewater pre- treated by Fenton oxidation was treated by aerobic activated sludge. It was found that a small amount of H202 can significantly increase both the biodegradation rate and extent of the wastewater. The effluent CODc, and HPAM contents were 260 and 94 mg/L respectively after the aerobic bio- logical process with the biodegradation time of 24 h. After Fenton oxidation combining with biodegradation, the total CODc, removal efficiency was up to 90%, and polymer and oil degrading efficiencies were 95% and 92% respectively.
文摘Anode material for lithium ion battery is prepared by chemical oxidation of natural graphite. After oxidation, the properties of natural graphite are modified, such as surface structure, the content of graphite phases, the number of micropores and its stability. thus the modified natural graphite can be used as anode material for commercial lithium ion battery. The reversible capacity is increased from 100 mAh/g to above 300 mAh/g, and its cycling properly is also satisfactory.
基金supported by the National Defense Science and Technology Innovation Zone Project(No.18-H863-05-ZT-001-018-09)
文摘A novel sensor for ocean electric field testing has been fabricated by polyacrylonitrile-based on carbon fibers with electro-chemical oxidation.The surface profile characteristics of the carbon fibers were characterized by scanning electron microscope,Fourier transform infrared spectra and contact angle.Cyclic voltammetry and Tafel curves have been used to study its electro-chemical performances.Two identical electrodes in sea water as the electric field sensor will swiftly respond to applied electric field which causes positive and negative ions to move in opposite direction,resulting in a electric potential difference(ΔE).Test result indicates that the offset potential is typically below 1 m V with a drift of 60-170μVd^-1.Typical self noise level is 1.07 nV√Hz^(1/2)@1 Hz.The electric field response indicates that the modified electrode pair shows better response to AC sine signal of amplitude and frequency(5 mV and 1 mHz)respectively than its blank.The electric field response model of the modified electrodes is creatively presented according to its electric double layer capacitance and Faraday pseudo-capacitance.Many advantages of the carbon fiber electric field electrode will make it have potential application prospect.
基金Project (2006CB600908) supported by National Basic Research Program of China
文摘To improve the oxidation-resistance properties,SiC and TaC species were introduced in C/C composites by chemical vapor infiltration(CVI) methods. The oxidation-resistance properties of C-SiC-TaC-C composites were studied by X-Ray diffractometry(XRD),JEOL-6360LV scanning electronic microscopy(SEM) and AdventurerTM electronic balance with precision of 0.1 mg. The results show that,1) the oxidation rate of the composites increases continuously with time at all experimental temperatures;2) The oxidation rate increases with temperature within 700-1 100 ℃,slowly in 700-800 ℃,acutely in 800-1 100 ℃;it reaches a maximum value at 1 100 ℃,then decreases within 1 100-1 400 ℃;3) The relationship curve of oxidation rate with temperature can be divided into three regions. The oxidation rate is controlled by reactivity in region Ⅰ,the mixed effects of reactivity and gas diffusion in region Ⅱ,gas phase diffusion in region Ⅲ;4) The composites exhibit a higher oxidation onset temperature in low temperature region and a lower oxidation rate at high temperature due to the oxidation of TaC to(Ta,O) and the formation of the dense SiO2-Ta2O5 oxide layer respectively. With the addition of SiC/TaC species,the oxidation-resistant properties of C/C composites can be improved effectively.
基金Supported by the National Natural Science Fundation of China.
文摘XPS and chemical trapping experments with H2, NH3, and CH3I as trapping agents were carried out for studying the adsorption of propylene over MoO3 or r-Bi2MoO6. The results show that the fragmentation of carbon chain takes place during the adsorption of propylene through breaking C -C double bond and C-C bond on Mo2+ and the adjacent lattice oxygen, leading to formation of the oxygen- or nitrogen-containing by-products of C1 and C2 species. Diffuse-Reflection Fourier Transform Infrared (DRFTIR) Spectroscopy was used to study the surface species formed during the chemisorption and reaction of propylene over y-Bi2MoO6 at a lower temperature. The results that C1, C2 adspecies were detected by DRFTIR at 175℃ are consistent with the results of XPS and chemical trapping experiments, whlle the results at 50℃ Grasselli et al.
文摘The experimental degradation of a water soluble dye, potassium indigo tetrasulfonate salt, has been studied using stand-alone ozonation and photocatalytic oxidation process. Progress of the dye oxidation was followed by UV-VIS spectrophotometric measurements at controlled operating conditions. The organic content of reaction samples was measured to verify the process efficiency in dye mineralization. According to current results, almost complete color removal was obtained for ozonation within about 1 h reaction time. The reduction of the organic load was almost 80% from its original while initial sulphur content decreased to 32.5%. Dye conversion of 100% was obtained by means of a photocatalytic process using TiO2 as catalyst at 294 nm irradiated UV light. This complete color removal for the catalytic process was observed within 7 min of reaction time. The calculated initial rate of reaction of photocatalysis treatment was 8 times faster than that of ozonolysis. However, the remaining organic load of photocatalysis was almost 88% from its original while the final sulphur content was 27.3%. This contrasting behavior of the performance of the type of oxidation process stressed importance of physicochemical phenomena and intermediates molecules present during dye degradation. An insightful and mechanistic aspect of the dye oxidation was developed by performing quantumchemical calculations.
文摘Nano-TiO2 photocatalytic oxidation was used to perform the advanced treatment of biologically treated chemical comprehensive wastewater. The effects of reaction time,nano-TiO2 dosage and initial p H of the wastewater on the removal rate of COD were tested. The GC/MS and EEM techniques were used to qualitatively analyze organic compounds in the wastewater before and after treatment. The result showed that after the biologically treated chemical comprehensive wastewater was treated by nano-TiO2 photocatalytic oxidation under the conditions of reaction time 3 h,nano-TiO2 dosage 8 g/L,and pH 8. 0,the effluent COD was 61. 9 mg/L and its removal rate was 63. 8%. Additionally,the species of organic pollutants reduced from 12 to 6. Meanwhile,the content of humic-like and fulvic-like substances dropped dramatically.
文摘Acidic black 10B dye wastewater was treated by chemical oxidation and adsorption of activated carbon fixed bed and all kinds of influential factors of removal CODcr were discussed. When the initial concentration of the dye was 150 mg/L, CODer was 432 mg/L and chrome was 2800 times, the appropriate conditions determined by the experiment were as follows: r(NaC10)--4.84 g/L, 25 min, pH=6, height of activated carbon fixed bed was 10 cm. Under these conditions, the decolorizing rate can come up to about 100% and total removed rate of CODer reached at 89.6%. Comparison of UV-Vis adsorption spectrums before and after treatment showed that decomposition effects of chemical oxidation and adsorption of activated carbon fixed bed on acidic black 10B dye wastewater were satisfactory.
基金supported by the National High Technology Research and Development Program of China (2011AA10A106)the National Natural Science Foundation of China (31171611, 31371697)+1 种基金the Technological Innovation and Over Planning Projects of Shaanxi Province, China (2014KTZB02-01-02, 2011KTZB02-01-01)the Projects Opening Up New Function of Precision Instrument of Northwest A&F University, China (dysb130210)
文摘Male sterility induced by a chemical hybridization agent (CHA) is an important tool for utilizing crop heterosis. Leaves, especially the flag leaves, as CHA initial recipients play a decisive role in inducing male sterility. To investigate effects of different treatment times of CHA-SQ-1 used, morphological, biochemical and physiological responses of wheat flag leaves were detected in thistudy. CHA induced programmed cell death (PCD) as shown in terminal deoxynucleotidyl transferase-mediated dUTP nick end-labelling (TUNEL) and DNA laddering analysis. In the early phase, CHA-SQ-1 trig- gered organelle changes arid PCD in wheat leaves accompanied by excess production of reactive oxygen species (O2- and H202) and down-regulation of the activities of superoxide dismutase (SOD), catalase (CAT) and guaiacol peroxidase (POD). Meanwhile, leaf cell DNAs showed ladder-like patterns on agarose gel, indicating that CHA-SQ-1 led to the activation of the responsible endonuclease. The oxidative stress assays showed that lipid peroxidation was strongly activated and photosynthesis was obviously inhibited in SQ-l-induced leaves. However, CHA contents in wheat leaves gradually reduced along with the time CHA-SQ-1 applied. Young flags returned to an oxidative/antioxidative balance and ultimately developed into mature green leaves. These results provide explanation of the relations between PCD and anther abortion and practical application of CHA for hybrid breeding.
文摘The results of a system analysis of the efficiency of nitrous oxide(N_2O) as a propellant component for small space vehicles(SSV) were presented. A criterion for mass efficiency of the SSV propulsion system(PS) is determined. The current global state-of-the-art of SSV PSs is shown. The application field of nitrous oxide in SSV PSs is calculated and mass efficiency of N_2O application is quantitatively determined. An overview of physical and chemical as well as operational properties of nitrous oxide as a promising, non-toxic component of rocket propellant is provided. Main physical and chemical constants of gaseous and liquid nitrous oxide; chemical properties of N_2O, thermal stability of N_2O, catalytic decomposition of N_2O, a mechanism of decomposition of N_2O, catalysts for decomposition of N_2O, ballast additives to N_2O, application of nitrous oxide, nitrous oxide as a rocket propellant, production of nitrous oxide, toxicity of nitrous oxide, fire hazard of N_2O, requirements to equipment when handling N_2O; storage and transportation of N_2O are considered. It is demonstrated that nitrous oxide is a chemical compound meeting the requirements to rocket propellants, including those related to the environmental friendliness of propellants. With 75 references.
基金Funded by the National Natural Science Foundation of China(No. 51171011)
文摘The chemical stripping method of titanium alloy oxide films was studied. An environment friendly solution hydrogen peroxide and sodium hydroxide without hydrofluoric acid or fluoride were used to strip the oxide films. The morphologies of the surface and cross-section of the oxide films before and after the films stripping were characterized by using scanning electron microscopy (SEM). The microstructure and chemical compositions of the oxide films before and after the films stripping were investigated by using Raman spectroscopy (Raman) and X-ray photoelectron spectroscopy (XPS). It was shown that the thickness of the oxide film was in the range of 5-6 μm. The oxide films were stripped for 2 to 8 min in the solution. Moreover, the effect of the stripping time on the efficiency of the film stripping was investigated, and the optimum stripping time was between 6-8 min. When the stripping solution completely dissolved the whole film, the α/β microstructure of the titanium alloy Ti-10V-2Fe-3Al was partly revealed. The stripping mechanism was discussed in terms of the dissolution of film delamination. The hydrogen peroxide had a significant effect on the dissolution of the titanium alloy anodic oxide film. The feasibility of the dissolution reaction also was evaluated.