An internal failure mode for a soil-nailed system consists of failure at nail heads,slope facing,nail strength,along groutesoil interface and pullout failure.A better understanding of pullout of soil nail thus becomes...An internal failure mode for a soil-nailed system consists of failure at nail heads,slope facing,nail strength,along groutesoil interface and pullout failure.A better understanding of pullout of soil nail thus becomes important to assess the stability of a soil-nailed system.In the present study,an investigation into the pullout behaviour of soil nail with circular discs along the shaft has been carried out by a threedimensional finite element analysis using Abaqus/Explicit routine.A total of 67 simulations have been performed to accurately predict the pullout behaviour of soil nail.The soil nail under study has circular discs along its shaft varying in numbers from 1 to 4.The pullout of this soil nail in a pullout test box has been simulated with a constant overburden pressure of 20 kPa acting on the nail.The pullout load edisplacement characteristics,stresses around soil nail and failure mechanism during pullout are studied.Variations of dimensionless factors such as normalised pullout load factor and bearing capacity factor have been obtained with different combinations of parameters in terms of relative disc spacing ratio,anchorage length ratio,embedment ratio,diameter ratio and displacement ratio.From the results of analyses,it is found that nail with more circular discs requires higher pullout load.There are critical relative disc spacing ratio and diameter ratio which significantly affect the pullout behaviour of nail.展开更多
Mode matching is used for the analysis of monopole antenna on circular disc, which is achieved by developing a novel model consisting of two artificial ground planes above and bellow the monopole antenna. Using this m...Mode matching is used for the analysis of monopole antenna on circular disc, which is achieved by developing a novel model consisting of two artificial ground planes above and bellow the monopole antenna. Using this model, the input impedance is computed and compared with measured data reported in literatures, and excellent agreement is observed.展开更多
Under spinning conditions, lubricant on islandic spot patterned M2 steel disc experiences centrifugal and tangential force components. Depending upon the relative position of the spots and the flow of lubricant, accum...Under spinning conditions, lubricant on islandic spot patterned M2 steel disc experiences centrifugal and tangential force components. Depending upon the relative position of the spots and the flow of lubricant, accumulation of lubricant in front of patterned islandic spots creates thrusting to mating part and subsequently reduces contact between the mating couple. Whilst wear debris is likely to be spun off the plateau of the spots to their neighbouring valleys so as to reduce wear. Hence, it gives favorable tribological characteristics. Aiming at verifying such mechanisms, studies were performed on M2 steel disc specimens slid with ASSAB 17 tool steel pin. The M2 steel disc specimens were respectively （i） machined with non-patterned （NP）, （ii） etched to produce in-lined （INE） islandic patterns, and （iii） etched to produce staggered （STE） islandic spot patterns. Results indicated that the INE patterned discs gave most favorable wear characteristics, the NP of the worse characteristics whilst the STE ranged in the middle. However, the actual contact mechanism leads to the descending sequence of favorable friction behaviors nominally as： NP, INE and STE.展开更多
A method of calculating a possible stability loss by a rotating circular annular disc of variable thickness is suggested within the theory of perfect plasticity with the help of small parameter method. A characteristi...A method of calculating a possible stability loss by a rotating circular annular disc of variable thickness is suggested within the theory of perfect plasticity with the help of small parameter method. A characteristic equation for a critical radius of a plastic zone is obtained as a first approximation. The formula for the critical angular velocity, determining the stability loss of the disc according to the self-balanced form, is derived. The method using which we can take into account the disc’s geometry and loading parameters is also specified. The efficiency of the proposed method is shown in Section 5 while considering an illustrative example. The values of critical angular velocity of rotating are found numerically for different parameters of the disc.展开更多
For a rotating inhomogeneous circular disk a way of calculating dynamics of boundary shape perturbation and failure of bearing capacity is proposed in terms of small parameter method. Characteristic equation of plasti...For a rotating inhomogeneous circular disk a way of calculating dynamics of boundary shape perturbation and failure of bearing capacity is proposed in terms of small parameter method. Characteristic equation of plastic zone critical radius is obtained as a first approximation. A formula of critical angular velocity is derived which determines the stability loss of the disc according to the self-balanced form. Efficiency of the proposed method is shown by an illustrative example considered in Section 7. Values of critical angular velocity of rotation are found numerically for different parameters of the disc.展开更多
文摘An internal failure mode for a soil-nailed system consists of failure at nail heads,slope facing,nail strength,along groutesoil interface and pullout failure.A better understanding of pullout of soil nail thus becomes important to assess the stability of a soil-nailed system.In the present study,an investigation into the pullout behaviour of soil nail with circular discs along the shaft has been carried out by a threedimensional finite element analysis using Abaqus/Explicit routine.A total of 67 simulations have been performed to accurately predict the pullout behaviour of soil nail.The soil nail under study has circular discs along its shaft varying in numbers from 1 to 4.The pullout of this soil nail in a pullout test box has been simulated with a constant overburden pressure of 20 kPa acting on the nail.The pullout load edisplacement characteristics,stresses around soil nail and failure mechanism during pullout are studied.Variations of dimensionless factors such as normalised pullout load factor and bearing capacity factor have been obtained with different combinations of parameters in terms of relative disc spacing ratio,anchorage length ratio,embedment ratio,diameter ratio and displacement ratio.From the results of analyses,it is found that nail with more circular discs requires higher pullout load.There are critical relative disc spacing ratio and diameter ratio which significantly affect the pullout behaviour of nail.
文摘Mode matching is used for the analysis of monopole antenna on circular disc, which is achieved by developing a novel model consisting of two artificial ground planes above and bellow the monopole antenna. Using this model, the input impedance is computed and compared with measured data reported in literatures, and excellent agreement is observed.
基金the National Natural Science Foundation of China(No. 50575173).
文摘Under spinning conditions, lubricant on islandic spot patterned M2 steel disc experiences centrifugal and tangential force components. Depending upon the relative position of the spots and the flow of lubricant, accumulation of lubricant in front of patterned islandic spots creates thrusting to mating part and subsequently reduces contact between the mating couple. Whilst wear debris is likely to be spun off the plateau of the spots to their neighbouring valleys so as to reduce wear. Hence, it gives favorable tribological characteristics. Aiming at verifying such mechanisms, studies were performed on M2 steel disc specimens slid with ASSAB 17 tool steel pin. The M2 steel disc specimens were respectively （i） machined with non-patterned （NP）, （ii） etched to produce in-lined （INE） islandic patterns, and （iii） etched to produce staggered （STE） islandic spot patterns. Results indicated that the INE patterned discs gave most favorable wear characteristics, the NP of the worse characteristics whilst the STE ranged in the middle. However, the actual contact mechanism leads to the descending sequence of favorable friction behaviors nominally as： NP, INE and STE.
文摘A method of calculating a possible stability loss by a rotating circular annular disc of variable thickness is suggested within the theory of perfect plasticity with the help of small parameter method. A characteristic equation for a critical radius of a plastic zone is obtained as a first approximation. The formula for the critical angular velocity, determining the stability loss of the disc according to the self-balanced form, is derived. The method using which we can take into account the disc’s geometry and loading parameters is also specified. The efficiency of the proposed method is shown in Section 5 while considering an illustrative example. The values of critical angular velocity of rotating are found numerically for different parameters of the disc.
文摘For a rotating inhomogeneous circular disk a way of calculating dynamics of boundary shape perturbation and failure of bearing capacity is proposed in terms of small parameter method. Characteristic equation of plastic zone critical radius is obtained as a first approximation. A formula of critical angular velocity is derived which determines the stability loss of the disc according to the self-balanced form. Efficiency of the proposed method is shown by an illustrative example considered in Section 7. Values of critical angular velocity of rotation are found numerically for different parameters of the disc.
