Rolling path squeezes and rolling residual stresses of large diameter circular saw body for wood, generated by rolling pressure from 10 up to 120 bar were examined. X-ray diffraction, Barkhausen noise (BN) and Full Wi...Rolling path squeezes and rolling residual stresses of large diameter circular saw body for wood, generated by rolling pressure from 10 up to 120 bar were examined. X-ray diffraction, Barkhausen noise (BN) and Full Width of the peak at a Half Maximum (FWHM) (o) methods for evaluation of residual stresses were used. Dependencies of a tangential rolling residual stresses inside rolling paths upon rolling pressure p (bar) and rolling area A (mm2) were evaluated. The rolling pressure, as large as 60 bar, resulting in the rolling squeeze as high as 0.04 mm2, and, tangential residual compression stresses inside a rolling path, as large as ?TI = ?822 MPa, was considered to be the largest for the practical application.展开更多
To look for the optimum cutting speed, the tungsten carbide tipped saw was used asan example in this paper. And then, on the basis of the experimental results and theoretical calculation,the equations of tool life was...To look for the optimum cutting speed, the tungsten carbide tipped saw was used asan example in this paper. And then, on the basis of the experimental results and theoretical calculation,the equations of tool life was introduced, and as an example, the minimum cost and maximum production cutting speed When the particleboards were cut by circulax saw, were obtained.展开更多
The effects of the location,number and stiffness of guide pads on the lowest critical rotational frequencies of the rotating circular saw damped at the inside and free at the perimeter are discussed by the non linear...The effects of the location,number and stiffness of guide pads on the lowest critical rotational frequencies of the rotating circular saw damped at the inside and free at the perimeter are discussed by the non linear theory and the perturbation theory of structural vibration analysis The influence of the centrifugal force and the cutting temperature are considered in the course of the analysis The results of the analysis and the calculation show that the introduction of one guide does not stably raise critical rotational frequencies of the circular saw The two guides can raise lowest critical rotational frequency of the circular saw when the angle between the two guides fixed on the direction of the circumference satisfies the certain conditions展开更多
本文分析了圆锯片设计及制造优化中减振降噪水平与动态稳定性的研究热点与前沿理论的演进路径,基于可视化分析软件CiteSpace,以2002—2022年中国知网和Web of Science核心合集数据库为数据来源,分别从年发文量、关键词、发文作者及发文...本文分析了圆锯片设计及制造优化中减振降噪水平与动态稳定性的研究热点与前沿理论的演进路径,基于可视化分析软件CiteSpace,以2002—2022年中国知网和Web of Science核心合集数据库为数据来源,分别从年发文量、关键词、发文作者及发文机构,对圆锯片结构设计及生产工艺的一般方法及特点进行初步探讨,根据关键词时间线及突显词对未来发展趋势进行展望。研究结果表明,2002—2022年圆锯片相关研究领域的中英文文献发文量平稳,研究机构间的合作相对分散,研究热点主要集中在圆锯片结构设计优化和生产工艺优化方面。结合关键词演变知识图谱,总结了提升圆锯片减振降噪水平及动态稳定性的方法,指明了该领域未来的研究重点和发展方向。展开更多
基金support of the Poznan Networking&Supercomputing Center(PCSS)calculation grant
文摘Rolling path squeezes and rolling residual stresses of large diameter circular saw body for wood, generated by rolling pressure from 10 up to 120 bar were examined. X-ray diffraction, Barkhausen noise (BN) and Full Width of the peak at a Half Maximum (FWHM) (o) methods for evaluation of residual stresses were used. Dependencies of a tangential rolling residual stresses inside rolling paths upon rolling pressure p (bar) and rolling area A (mm2) were evaluated. The rolling pressure, as large as 60 bar, resulting in the rolling squeeze as high as 0.04 mm2, and, tangential residual compression stresses inside a rolling path, as large as ?TI = ?822 MPa, was considered to be the largest for the practical application.
文摘To look for the optimum cutting speed, the tungsten carbide tipped saw was used asan example in this paper. And then, on the basis of the experimental results and theoretical calculation,the equations of tool life was introduced, and as an example, the minimum cost and maximum production cutting speed When the particleboards were cut by circulax saw, were obtained.
文摘The effects of the location,number and stiffness of guide pads on the lowest critical rotational frequencies of the rotating circular saw damped at the inside and free at the perimeter are discussed by the non linear theory and the perturbation theory of structural vibration analysis The influence of the centrifugal force and the cutting temperature are considered in the course of the analysis The results of the analysis and the calculation show that the introduction of one guide does not stably raise critical rotational frequencies of the circular saw The two guides can raise lowest critical rotational frequency of the circular saw when the angle between the two guides fixed on the direction of the circumference satisfies the certain conditions
文摘本文分析了圆锯片设计及制造优化中减振降噪水平与动态稳定性的研究热点与前沿理论的演进路径,基于可视化分析软件CiteSpace,以2002—2022年中国知网和Web of Science核心合集数据库为数据来源,分别从年发文量、关键词、发文作者及发文机构,对圆锯片结构设计及生产工艺的一般方法及特点进行初步探讨,根据关键词时间线及突显词对未来发展趋势进行展望。研究结果表明,2002—2022年圆锯片相关研究领域的中英文文献发文量平稳,研究机构间的合作相对分散,研究热点主要集中在圆锯片结构设计优化和生产工艺优化方面。结合关键词演变知识图谱,总结了提升圆锯片减振降噪水平及动态稳定性的方法,指明了该领域未来的研究重点和发展方向。
